ElectroMagnetic Compatibility (EMC) standard for radio equipment and services - Part 33: Specific conditions for Ultra-WideBand (UWB) devices - Harmonised Standard covering the essential requirements of article 3.1(b) of the Directive 2014/53/EU

The present document, together with ETSI EN 301 489-1 [1], specifies technical characteristics and methods of
measurements for radio devices based on UWB technology in respect of ElectroMagnetic Compatibility (EMC).
The present document applies to fixed, mobile or portable UWB devices, e.g.:
• stand alone radio equipment with or without its own control provisions;
• plug-in radio devices intended for use with, or within, a variety of host systems, e.g. personal computers,
hand-held terminals, etc.;
• plug-in radio devices intended for use within combined equipment, e.g. cable modems, set-top boxes, access
points, etc.;
• combined equipment or a combination of a plug-in radio device and a specific type of host equipment;
• equipment for use in road and rail vehicles;
• ground and wall probing radar equipment;
• (tank) level probing radar equipment;
• material sensing devices.
NOTE: If a system includes transponders, these are measured together with the transmitter and examples of
Ultra-WideBand equipment are given in the related harmonised standards of article 3.2 of Directive
2014/53/EU [i.1].
Technical specifications related to the antenna port and emissions from the enclosure port of Ultra-WideBand (UWB)
equipment are not included in the present document. Such technical specifications are found in the relevant product
standards for the effective use of the radio spectrum.
The present document specifies the applicable test conditions, performance assessment and performance criteria for
Ultra-WideBand (UWB) equipment and associated ancillary equipment.
Examples of Ultra-WideBand equipment are given in the related harmonised standards.
In case of differences (for instance concerning special conditions, definitions, abbreviations) between the present
document and ETSI EN 301 489-1 [1], the provisions of the present document take precedence.
The environmental classification and the emission and immunity requirements used in the present document are as
stated in ETSI EN 301 489-1 [1], except for any special conditions included in the present document.
The present document covers the essential requirements of article 3.1b of Directive 2014/53/EU [i.1] under the
conditions identified in annex A.

Standard elektromagnetne združljivosti (EMC) za radijsko opremo in storitve - 33. del: Posebni pogoji za ultra širokopasovne (UWB) naprave - Harmonizirani standard, ki zajema bistvene zahteve člena 3.1(b) direktive 2014/53/EU

Ta dokument skupaj s standardom ETSI EN 301 489-1 [1] določa tehnične karakteristike in merilne metode za ultra širokopasovne (UWB) radijske naprave v zvezi z elektromagnetno združljivostjo (EMC).
Ta dokument se uporablja za fiksne, mobilne ali prenosne ultra širokopasovne naprave, npr.:
• samostojno radijsko opremo s pripadajočimi določbami o nadzoru ali brez;
• vtične radijske naprave za uporabo z različnimi gostiteljskimi sistemi, npr. osebnimi računalniki, ročnimi terminali itd., ali v njih;
•vtične radijske naprave za uporabo v sestavljenih sistemih, npr. kabelskih modemih, komunikatorjih, dostopnih točkah itd.;
• sestavljene sisteme ali kombinacijo vtične radijske naprave in posebne vrste gostiteljske opreme;
• opremo, ki se uporablja v cestnih in železniških vozilih;
• radarsko opremo za sondiranje tal in zidov;
• opremo za sondiranje nivoja v rezervoarjih;
• zaznavala snovi.
OPOMBA: Če sistem vključuje transponderje, se ti izmerijo skupaj z oddajnikom, in primeri ultra širokopasovne opreme so podani v ustreznih harmoniziranih standardih člena 3.2 direktive 2014/53/EU [i.1].
Ta dokument ne vključuje tehničnih specifikacij v zvezi z antenskim vhodom in sevanjem iz vhoda na ohišju ultra širokopasovne opreme. Takšne tehnične specifikacije so navedene v ustreznih standardih za izdelek na področju učinkovite uporabe radijskega spektra.
Ta dokument določa veljavne preskusne pogoje, oceno zmogljivosti in merila zmogljivosti za ultra širokopasovno opremo in povezano pomožno opremo.
Primeri ultra širokopasovne opreme so podani v ustreznih harmoniziranih standardih.
Če se ta dokument in standard ETSI EN 301 489-1 [1] razlikujeta (na primer glede posebnih pogojev, opredelitev, kratic), imajo prednost določbe tega dokumenta.
Okoljska razvrstitev ter zahteve glede sevanja in odpornosti iz tega dokumenta so navedene v standardu ETSI EN 301 489-1 [1], razen posebnih pogojev iz tega dokumenta.
Ta dokument zajema bistvene zahteve člena 3.1b direktive 2014/53/EU [i.1] pod pogoji iz dodatka A.

General Information

Status
Published
Public Enquiry End Date
30-Jun-2016
Publication Date
27-Feb-2017
Technical Committee
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
14-Feb-2017
Due Date
21-Apr-2017
Completion Date
28-Feb-2017

Buy Standard

Standard
SIST EN 301 489-33 V2.1.1:2017
English language
25 pages
sale 10% off
Preview
sale 10% off
Preview

e-Library read for
1 day
Standard
ETSI EN 301 489-33 V2.1.1 (2017-02) - Part 33: Specific conditions for Ultra-WideBand (UWB) devices; Part 33: Specific conditions for Ultra-WideBand (UWB) devices; Harmonised Standard covering the essential requirements of article 3.1(b) of Directive 2014/53/EU
English language
25 pages
sale 15% off
Preview
sale 15% off
Preview
Standard
ETSI EN 301 489-33 V2.1.1 (2016-11) - ElectroMagnetic Compatibility (EMC) standard for radio equipment and services; Part 33: Specific conditions for Ultra-WideBand (UWB) devices; Harmonised Standard covering the essential requirements of article 3.1(b) of Directive 2014/53/EU
English language
24 pages
sale 15% off
Preview
sale 15% off
Preview
Standard
ETSI EN 301 489-33 V2.1.0 (2016-04) - ElectroMagnetic Compatibility (EMC) standard for radio equipment and services; Part 33: Specific conditions for Ultra-WideBand (UWB) devices; Harmonised Standard covering the essential requirements of article 3.1(b) of the Directive 2014/53/EU
English language
18 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.L]LUDQL(8ElectroMagnetic Compatibility (EMC) standard for radio equipment and services - Part 33: Specific conditions for Ultra-WideBand (UWB) devices - Harmonised Standard covering the essential requirements of article 3.1(b) of the Directive 2014/53/EU33.100.01Elektromagnetna združljivost na splošnoElectromagnetic compatibility in general33.060.20Sprejemna in oddajna opremaReceiving and transmitting equipmentICS:Ta slovenski standard je istoveten z:ETSI EN 301 489-33 V2.1.1 (2017-02)SIST EN 301 489-33 V2.1.1:2017en01-april-2017SIST EN 301 489-33 V2.1.1:2017SLOVENSKI

STANDARD
SIST EN 301 489-33 V2.1.1:2017

ETSI EN 301 489-33 V2.1.1 (2017-02) ElectroMagnetic Compatibility (EMC) standard for radio equipment and services; Part 33: Specific conditions for Ultra-WideBand (UWB) devices; Harmonised Standard covering the essential requirements of article 3.1(b) of Directive 2014/53/EU

HARMONISED EUROPEAN STANDARD SIST EN 301 489-33 V2.1.1:2017
ETSI ETSI EN 301 489-33 V2.1.1 (2017-02)2

Reference REN/ERM-EMC-343 Keywords EMC, harmonised standard, radio, UWB ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: +33 4 92 94 42 00
Fax: +33 4 93 65 47 16

Siret N° 348 623 562 00017 - NAF 742 C Association à but non lucratif enregistrée à la Sous-Préfecture de Grasse (06) N° 7803/88

Important notice The present document can be downloaded from: http://www.etsi.org/standards-search The present document may be made available in electronic versions and/or in print. The content of any electronic and/or print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx If you find errors in the present document, please send your comment to one of the following services: https://portal.etsi.org/People/CommiteeSupportStaff.aspx Copyright Notification No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm except as authorized by written permission of ETSI. The content of the PDF version shall not be modified without the written authorization of ETSI. The copyright and the foregoing restriction extend to reproduction in all media.

© European Telecommunications Standards Institute 2017. All rights reserved.

DECTTM, PLUGTESTSTM, UMTSTM and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members. 3GPPTM and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association. SIST EN 301 489-33 V2.1.1:2017

ETSI ETSI EN 301 489-33 V2.1.1 (2017-02)3 Contents Intellectual Property Rights ................................................................................................................................ 5 Foreword ............................................................................................................................................................. 5 Modal verbs terminology .................................................................................................................................... 5 1 Scope ........................................................................................................................................................ 6 2 References ................................................................................................................................................ 6 2.1 Normative references ......................................................................................................................................... 6 2.2 Informative references ........................................................................................................................................ 8 3 Definitions and abbreviations ................................................................................................................... 8 3.1 Definitions .......................................................................................................................................................... 8 3.2 Abbreviations ..................................................................................................................................................... 8 4 Test conditions ......................................................................................................................................... 8 4.1 General ............................................................................................................................................................... 8 4.2 Arrangements for test signals ............................................................................................................................. 8 4.2.1 General .......................................................................................................................................................... 8 4.2.2 Arrangements for test signals at the RF input of transmitters ....................................................................... 8 4.2.3 Arrangements for test signals at the RF output of transmitters ..................................................................... 9 4.2.4 Arrangements for test signals at the RF input of receivers ........................................................................... 9 4.2.5 Arrangements for test signals at the RF output of receivers ......................................................................... 9 4.2.6 Arrangements for testing transmitter and receiver together (as a system) .................................................... 9 4.3 Exclusion bands .................................................................................................................................................. 9 4.3.1 for EMC emission test .................................................................................................................................. 9 4.3.2 for EMC immunity test ................................................................................................................................. 9 4.4 Narrow band responses of receivers ................................................................................................................. 10 4.5 Normal test modulation .................................................................................................................................... 10 5 Performance assessment ......................................................................................................................... 10 5.1 General ............................................................................................................................................................. 10 5.2 Equipment which can provide an UWB communications link ......................................................................... 10 5.3 Equipment which does not provide an UWB communications link ................................................................. 10 5.4 Ancillary equipment ......................................................................................................................................... 10 5.5 Equipment classification .................................................................................................................................. 10 6 Performance criteria ............................................................................................................................... 11 6.0 Introduction ...................................................................................................................................................... 11 6.1 Performance criteria for continuous phenomena applied to transmitters and receivers ................................... 11 6.2 Performance criteria for transient phenomena applied to transmitters and receivers ....................................... 11 6.3 Performance criteria for equipment which does not provide an UWB communication link ............................ 11 6.4 Performance criteria for ancillary equipment tested on a stand alone basis ..................................................... 12 7 Applicability overview ........................................................................................................................... 12 7.1 Emission ........................................................................................................................................................... 12 7.2 Immunity .......................................................................................................................................................... 12 8 Methods of measurement and limits for EMC emissions ...................................................................... 12 8.1 Test configuration............................................................................................................................................. 12 8.2 Enclosure port of ancillary equipment measured on a stand alone basis .......................................................... 12 8.2.1 General ........................................................................................................................................................ 12 8.2.2 Test method ................................................................................................................................................ 13 8.2.3 Limits .......................................................................................................................................................... 13 8.3 DC power input/output ports ............................................................................................................................ 13 8.3.1 General ........................................................................................................................................................ 13 8.3.2 Test method ................................................................................................................................................ 13 8.3.3 Limits .......................................................................................................................................................... 13 8.4 AC mains power input/output ports ................................................................................................................. 14 8.4.1 General ........................................................................................................................................................ 14 8.4.2 Test method ................................................................................................................................................ 14 SIST EN 301 489-33 V2.1.1:2017

ETSI ETSI EN 301 489-33 V2.1.1 (2017-02)4 8.4.3 Limits .......................................................................................................................................................... 14 8.4.3.1 General .................................................................................................................................................. 14 8.4.3.2 AC Power port used for power supply only .......................................................................................... 14 8.4.3.3 AC power input port also used for PLC Communications .................................................................... 14 8.5 Harmonic current emissions (AC mains input port) ......................................................................................... 15 8.6 Voltage fluctuations and flicker (AC mains input port) ................................................................................... 15 8.7 Wired network ports ......................................................................................................................................... 15 8.7.1 General ........................................................................................................................................................ 15 8.7.2 Test method ................................................................................................................................................ 15 8.7.3 Limits .......................................................................................................................................................... 15 9 Test methods and levels for immunity tests ........................................................................................... 16 9.1 Test configuration............................................................................................................................................. 16 9.2 Radio frequency electromagnetic field (80 MHz to 6 000 MHz) ..................................................................... 16 9.2.1 General ........................................................................................................................................................ 16 9.2.2 Test method ................................................................................................................................................ 16 9.2.3 Performance criteria .................................................................................................................................... 16 9.3 Electrostatic discharge ...................................................................................................................................... 17 9.3.1 General ........................................................................................................................................................ 17 9.3.2 Test method ................................................................................................................................................ 17 9.3.3 Performance criteria .................................................................................................................................... 17 9.4 Fast transients, common mode ......................................................................................................................... 17 9.4.1 General ........................................................................................................................................................ 17 9.4.2 Test method ................................................................................................................................................ 17 9.4.3 Performance criteria .................................................................................................................................... 18 9.5 Radio frequency, common mode ...................................................................................................................... 18 9.5.1 General ........................................................................................................................................................ 18 9.5.2 Test method ................................................................................................................................................ 18 9.5.3 Performance criteria .................................................................................................................................... 18 9.6 Transients and surges in the vehicular environment ......................................................................................... 18 9.6.1 General ........................................................................................................................................................ 18 9.6.2 Test method ................................................................................................................................................ 19 9.6.3 Performance criteria .................................................................................................................................... 19 9.7 Voltage dips and interruptions .......................................................................................................................... 19 9.7.1 General ........................................................................................................................................................ 19 9.7.2 Test method ................................................................................................................................................ 19 9.7.3 Performance criteria .................................................................................................................................... 19 9.8 Surges ............................................................................................................................................................... 20 9.8.1 General ........................................................................................................................................................ 20 9.8.2 Test method ................................................................................................................................................ 20 9.8.2.0 General .................................................................................................................................................. 20 9.8.2.1 Test method for wired network ports directly connected to outdoor cables .......................................... 20 9.8.2.2 Test method for wired network ports connected to indoor cables ......................................................... 20 9.8.2.3 Test method for mains ports .................................................................................................................. 20 9.8.3 Performance criteria .................................................................................................................................... 21 Annex A (informative): Relationship between the present document and the essential requirements of Directive 2014/53/EU ......................................................... 22 Annex B (informative): Change history ............................................................................................... 24 History .............................................................................................................................................................. 25

SIST EN 301 489-33 V2.1.1:2017

ETSI ETSI EN 301 489-33 V2.1.1 (2017-02)5 Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (https://ipr.etsi.org/). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This Harmonised European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic compatibility and Radio spectrum Matters (ERM). The present document has been prepared under the Commission's standardisation request C(2015) 5376 final [i.2] to provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation of the laws of the Member States relating to the making available on the market of radio equipment and repealing Directive 1999/5/EC [i.1]. Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with the normative clauses of the present document given in table A.1 confers, within the limits of the scope of the present document, a presumption of conformity with the corresponding essential requirements of that Directive, and associated EFTA regulations. The present document is part 33 of a multi-part deliverable. Full details of the entire series can be found in part 1 [1].

National transposition dates Date of adoption of this EN: 27 January 2017 Date of latest announcement of this EN (doa): 30 April 2017 Date of latest publication of new National Standard or endorsement of this EN (dop/e):

31 October 2017 Date of withdrawal of any conflicting National Standard (dow): 31 October 2018

Modal verbs terminology In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and "cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of provisions). "must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation. SIST EN 301 489-33 V2.1.1:2017

ETSI ETSI EN 301 489-33 V2.1.1 (2017-02)6 1 Scope The present document, together with ETSI EN 301 489-1 [1], specifies technical characteristics and methods of measurements for radio devices based on UWB technology in respect of ElectroMagnetic Compatibility (EMC). The present document applies to fixed, mobile or portable UWB devices, e.g.: • stand alone radio equipment with or without its own control provisions; • plug-in radio devices intended for use with, or within, a variety of host systems, e.g. personal computers, hand-held terminals, etc.; • plug-in radio devices intended for use within combined equipment, e.g. cable modems, set-top boxes, access points, etc.; • combined equipment or a combination of a plug-in radio device and a specific type of host equipment; • equipment for use in road and rail vehicles; • ground and wall probing radar equipment; • (tank) level probing radar equipment; • material sensing devices. NOTE: If a system includes transponders, these are measured together with the transmitter and examples of Ultra-WideBand equipment are given in the related harmonised standards of article 3.2 of Directive 2014/53/EU [i.1]. Technical specifications related to the antenna port and emissions from the enclosure port of Ultra-WideBand (UWB) equipment are not included in the present document. Such technical specifications are found in the relevant product standards for the effective use of the radio spectrum. The present document specifies the applicable test conditions, performance assessment and performance criteria for Ultra-WideBand (UWB) equipment and associated ancillary equipment. Examples of Ultra-WideBand equipment are given in the related harmonised standards. In case of differences (for instance concerning special conditions, definitions, abbreviations) between the present document and ETSI EN 301 489-1 [1], the provisions of the present document take precedence. The environmental classification and the emission and immunity requirements used in the present document are as stated in ETSI EN 301 489-1 [1], except for any special conditions included in the present document. The present document covers the essential requirements of article 3.1b of Directive 2014/53/EU [i.1] under the conditions identified in annex A. 2 References 2.1 Normative references References are specific, identified by date of publication and/or edition number or version number. Only the cited version applies. Referenced documents which are not found to be publicly available in the expected location might be found at https://docbox.etsi.org/Reference/. NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee their long term validity. The following referenced documents are necessary for the application of the present document. SIST EN 301 489-33 V2.1.1:2017

ETSI ETSI EN 301 489-33 V2.1.1 (2017-02)7 [1] ETSI EN 301 489-1 (V2.1.1) (02-2017): "ElectroMagnetic Compatibility (EMC) standard for radio equipment and services; Part 1: Common technical requirements; Harmonised Standard covering the essential requirements of article 3.1(b) of Directive 2014/53/EU and the essential requirements of article 6 of Directive 2014/30/EU". [2] ETSI EN 302 065-1 (V2.1.1) (11-2016): "Short Range Devices (SRD) using Ultra Wide Band technology (UWB); Harmonised Standard covering the essential requirements of article 3.2 of the Directive 2014/53/EU; Part 1: Requirements for Generic UWB applications". [3] ETSI EN 302 065-2 (V2.1.1) (11-2016): "Short Range Devices (SRD) using Ultra Wide Band technology (UWB); Harmonised Standard covering the essential requirements of article 3.2 of the Directive 2014/53/EU; Part 2: Requirements for UWB location tracking". [4] ETSI EN 302 065-3 (V2.1.1) (11-2016): "Short Range Devices (SRD) using Ultra Wide Band technology (UWB); Harmonised Standard covering the essential requirements of article 3.2 of the Directive 2014/53/EU; Part 3: Requirements for UWB devices for ground based vehicular applications". [5] ETSI EN 302 065-4 (V1.1.1) (11-2016): "Short Range Devices (SRD) using Ultra Wide Band technology (UWB); Harmonised Standard covering the essential requirements of article 3.2 of the Directive 2014/53/EU; Part 4: Material Sensing devices using UWB technology below 10,6 GHz". [6] ETSI EN 302 066 (V2.1.1) (01-2017): "Short Range Devices (SRD); Ground- and Wall- Probing Radar applications (GPR/WPR) imaging systems; Harmonised Standard covering the essential requirements of article 3.2 of the Directive 2014/53/EU". [7] ETSI EN 302 372 (V2.1.1) (12-2016): "Short Range Devices (SRD); Tank Level Probing Radar (TLPR) equipment operating in the frequency ranges 4,5 GHz to 7 GHz, 8,5 GHz to 10,6 GHz, 24,05 GHz to 27 GHz, 57 GHz to 64 GHz, 75 GHz to 85 GHz; Harmonised Standard covering the essential requirements of article 3.2 of the Directive 2014/53/EU". [8] ETSI EN 302 729 (V2.1.1) (12-2016): "Short Range Devices (SRD); Level Probing Radar (LPR) equipment operating in the frequency ranges 6 GHz to 8,5 GHz, 24,05 GHz to 26,5 GHz, 57 GHz to 64 GHz, 75 GHz to 85 GHz; Harmonised Standard covering the essential requirements of article 3.2 of the Directive 2014/53/EU". [9] CENELEC EN 55032:2015: "Electromagnetic compatibility of multimedia equipment - Emission Requirements". [10] CENELEC EN 61326-1:2013: "Electrical equipment for measurement, control and laboratory use - EMC requirements - Part 1: General requirements". [11] CENELEC EN 61326-2-3:2013: "Electrical equipment for measurement, control and laboratory use - EMC requirements - Part 2-3: Particular requirements - Test configuration, operational conditions and performance criteria for transducers with integrated or remote signal conditioning". [12] CENELEC EN 61326-2-5:2013: "Electrical equipment for measurement, control and laboratory use - EMC requirements - Part 2-5: Particular requirements - Test configurations, operational conditions and performance criteria for field devices with interfaces according to IEC 61748-1, CP 3/2". [13] CENELEC EN 61000-6-2:2005: "Electromagnetic compatibility (EMC) - Part 6-2: Generic standards - Immunity for industrial environments". [14] CENELEC EN 61000-6-3:2007 "Electromagnetic compatibility (EMC) - Part 6-3: Generic standards -Emission standard for residential, commercial and light-industrial environments". [15] ETSI EN 303 883 (V1.1.1) (09-2016): "Short Range Devices (SRD) using Ultra Wide Band (UWB);Measurement Techniques". SIST EN 301 489-33 V2.1.1:2017

ETSI ETSI EN 301 489-33 V2.1.1 (2017-02)8 2.2 Informative references References are either specific (identified by date of publication and/or edition number or version number) or non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the referenced document (including any amendments) applies. NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee their long term validity. The following referenced documents are not necessary for the application of the present document but they assist the user with regard to a particular subject area. [i.1] Directive 2014/53/EU of the European Parliament and of the council of 16 April 2014 on the harmonisation of the laws of the Member States relating to the making available on the market of radio equipment and repealing Directive 1999/5/EC. [i.2] Commission Implementing Decision C(2015) 5376 final of 4.8.2015 on a standardisation request to the European Committee for Electrotechnical Standardisation and to the European Telecommunications Standards Institute as regards radio equipment in support of Directive 2014/53/EU of the European Parliament and of the Council. 3 Definitions and abbreviations 3.1 Definitions For the purposes of the present document, the terms and definitions given in ETSI EN 301 489-1, clause 3 [1] apply. 3.2 Abbreviations For the purposes of the present document, the abbreviations given in ETSI EN 301 489-1, clause 3 [1] and in specific UWB standards ETSI EN 302 065 parts 1 [2], 2 [3], 3 [4] and 4 [5], ETSI EN 302 066 [6], ETSI EN 302 372 [7] and ETSI EN 302 729 [8] apply. 4 Test conditions 4.1 General For the purposes of the present document, the test

...

ETSI EN 301 489-33 V2.1.1 (2017-02)
HARMONISED EUROPEAN STANDARD
ElectroMagnetic Compatibility (EMC)
standard for radio equipment and services;
Part 33: Specific conditions for
Ultra-WideBand (UWB) devices;
Harmonised Standard covering the essential requirements
of article 3.1(b) of Directive 2014/53/EU
---------------------- Page: 1 ----------------------
2 ETSI EN 301 489-33 V2.1.1 (2017-02)
Reference
REN/ERM-EMC-343
Keywords
EMC, harmonised standard, radio, UWB
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search

The present document may be made available in electronic versions and/or in print. The content of any electronic and/or

print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any

existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the

print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.

Users of the present document should be aware that the document may be subject to revision or change of status.

Information on the current status of this and other ETSI documents is available at

https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx

If you find errors in the present document, please send your comment to one of the following services:

https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification

No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying

and microfilm except as authorized by written permission of ETSI.

The content of the PDF version shall not be modified without the written authorization of ETSI.

The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2017.
All rights reserved.
TM TM TM

DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.

3GPP and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and

of the 3GPP Organizational Partners.

GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.

ETSI
---------------------- Page: 2 ----------------------
3 ETSI EN 301 489-33 V2.1.1 (2017-02)
Contents

Intellectual Property Rights ................................................................................................................................ 5

Foreword ............................................................................................................................................................. 5

Modal verbs terminology .................................................................................................................................... 5

1 Scope ........................................................................................................................................................ 6

2 References ................................................................................................................................................ 6

2.1 Normative references ......................................................................................................................................... 6

2.2 Informative references ........................................................................................................................................ 8

3 Definitions and abbreviations ................................................................................................................... 8

3.1 Definitions .......................................................................................................................................................... 8

3.2 Abbreviations ..................................................................................................................................................... 8

4 Test conditions ......................................................................................................................................... 8

4.1 General ............................................................................................................................................................... 8

4.2 Arrangements for test signals ............................................................................................................................. 8

4.2.1 General .......................................................................................................................................................... 8

4.2.2 Arrangements for test signals at the RF input of transmitters ....................................................................... 8

4.2.3 Arrangements for test signals at the RF output of transmitters ..................................................................... 9

4.2.4 Arrangements for test signals at the RF input of receivers ........................................................................... 9

4.2.5 Arrangements for test signals at the RF output of receivers ......................................................................... 9

4.2.6 Arrangements for testing transmitter and receiver together (as a system) .................................................... 9

4.3 Exclusion bands .................................................................................................................................................. 9

4.3.1 for EMC emission test .................................................................................................................................. 9

4.3.2 for EMC immunity test ................................................................................................................................. 9

4.4 Narrow band responses of receivers ................................................................................................................. 10

4.5 Normal test modulation .................................................................................................................................... 10

5 Performance assessment ......................................................................................................................... 10

5.1 General ............................................................................................................................................................. 10

5.2 Equipment which can provide an UWB communications link ......................................................................... 10

5.3 Equipment which does not provide an UWB communications link ................................................................. 10

5.4 Ancillary equipment ......................................................................................................................................... 10

5.5 Equipment classification .................................................................................................................................. 10

6 Performance criteria ............................................................................................................................... 11

6.0 Introduction ...................................................................................................................................................... 11

6.1 Performance criteria for continuous phenomena applied to transmitters and receivers ................................... 11

6.2 Performance criteria for transient phenomena applied to transmitters and receivers ....................................... 11

6.3 Performance criteria for equipment which does not provide an UWB communication link ............................ 11

6.4 Performance criteria for ancillary equipment tested on a stand alone basis ..................................................... 12

7 Applicability overview ........................................................................................................................... 12

7.1 Emission ........................................................................................................................................................... 12

7.2 Immunity .......................................................................................................................................................... 12

8 Methods of measurement and limits for EMC emissions ...................................................................... 12

8.1 Test configuration............................................................................................................................................. 12

8.2 Enclosure port of ancillary equipment measured on a stand alone basis .......................................................... 12

8.2.1 General ........................................................................................................................................................ 12

8.2.2 Test method ................................................................................................................................................ 13

8.2.3 Limits .......................................................................................................................................................... 13

8.3 DC power input/output ports ............................................................................................................................ 13

8.3.1 General ........................................................................................................................................................ 13

8.3.2 Test method ................................................................................................................................................ 13

8.3.3 Limits .......................................................................................................................................................... 13

8.4 AC mains power input/output ports ................................................................................................................. 14

8.4.1 General ........................................................................................................................................................ 14

8.4.2 Test method ................................................................................................................................................ 14

ETSI
---------------------- Page: 3 ----------------------
4 ETSI EN 301 489-33 V2.1.1 (2017-02)

8.4.3 Limits .......................................................................................................................................................... 14

8.4.3.1 General .................................................................................................................................................. 14

8.4.3.2 AC Power port used for power supply only .......................................................................................... 14

8.4.3.3 AC power input port also used for PLC Communications .................................................................... 14

8.5 Harmonic current emissions (AC mains input port) ......................................................................................... 15

8.6 Voltage fluctuations and flicker (AC mains input port) ................................................................................... 15

8.7 Wired network ports ......................................................................................................................................... 15

8.7.1 General ........................................................................................................................................................ 15

8.7.2 Test method ................................................................................................................................................ 15

8.7.3 Limits .......................................................................................................................................................... 15

9 Test methods and levels for immunity tests ........................................................................................... 16

9.1 Test configuration............................................................................................................................................. 16

9.2 Radio frequency electromagnetic field (80 MHz to 6 000 MHz) ..................................................................... 16

9.2.1 General ........................................................................................................................................................ 16

9.2.2 Test method ................................................................................................................................................ 16

9.2.3 Performance criteria .................................................................................................................................... 16

9.3 Electrostatic discharge ...................................................................................................................................... 17

9.3.1 General ........................................................................................................................................................ 17

9.3.2 Test method ................................................................................................................................................ 17

9.3.3 Performance criteria .................................................................................................................................... 17

9.4 Fast transients, common mode ......................................................................................................................... 17

9.4.1 General ........................................................................................................................................................ 17

9.4.2 Test method ................................................................................................................................................ 17

9.4.3 Performance criteria .................................................................................................................................... 18

9.5 Radio frequency, common mode ...................................................................................................................... 18

9.5.1 General ........................................................................................................................................................ 18

9.5.2 Test method ................................................................................................................................................ 18

9.5.3 Performance criteria .................................................................................................................................... 18

9.6 Transients and surges in the vehicular environment ......................................................................................... 18

9.6.1 General ........................................................................................................................................................ 18

9.6.2 Test method ................................................................................................................................................ 19

9.6.3 Performance criteria .................................................................................................................................... 19

9.7 Voltage dips and interruptions .......................................................................................................................... 19

9.7.1 General ........................................................................................................................................................ 19

9.7.2 Test method ................................................................................................................................................ 19

9.7.3 Performance criteria .................................................................................................................................... 19

9.8 Surges ............................................................................................................................................................... 20

9.8.1 General ........................................................................................................................................................ 20

9.8.2 Test method ................................................................................................................................................ 20

9.8.2.0 General .................................................................................................................................................. 20

9.8.2.1 Test method for wired network ports directly connected to outdoor cables .......................................... 20

9.8.2.2 Test method for wired network ports connected to indoor cables ......................................................... 20

9.8.2.3 Test method for mains ports .................................................................................................................. 20

9.8.3 Performance criteria .................................................................................................................................... 21

Annex A (informative): Relationship between the present document and the essential

requirements of Directive 2014/53/EU ......................................................... 22

Annex B (informative): Change history ............................................................................................... 24

History .............................................................................................................................................................. 25

ETSI
---------------------- Page: 4 ----------------------
5 ETSI EN 301 489-33 V2.1.1 (2017-02)
Intellectual Property Rights

IPRs essential or potentially essential to the present document may have been declared to ETSI. The information

pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found

in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in

respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web

server (https://ipr.etsi.org/).

Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee

can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web

server) which are, or may be, or may become, essential to the present document.
Foreword

This Harmonised European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic

compatibility and Radio spectrum Matters (ERM).

The present document has been prepared under the Commission's standardisation request C(2015) 5376 final [i.2] to

provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation

of the laws of the Member States relating to the making available on the market of radio equipment and repealing

Directive 1999/5/EC [i.1].

Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with

the normative clauses of the present document given in table A.1 confers, within the limits of the scope of the present

document, a presumption of conformity with the corresponding essential requirements of that Directive, and associated

EFTA regulations.

The present document is part 33 of a multi-part deliverable. Full details of the entire series can be found in part 1 [1].

National transposition dates
Date of adoption of this EN: 27 January 2017
Date of latest announcement of this EN (doa): 30 April 2017
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 31 October 2017
Date of withdrawal of any conflicting National Standard (dow): 31 October 2018
Modal verbs terminology

In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and

"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of

provisions).

"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.

ETSI
---------------------- Page: 5 ----------------------
6 ETSI EN 301 489-33 V2.1.1 (2017-02)
1 Scope

The present document, together with ETSI EN 301 489-1 [1], specifies technical characteristics and methods of

measurements for radio devices based on UWB technology in respect of ElectroMagnetic Compatibility (EMC).

The present document applies to fixed, mobile or portable UWB devices, e.g.:
• stand alone radio equipment with or without its own control provisions;

• plug-in radio devices intended for use with, or within, a variety of host systems, e.g. personal computers,

hand-held terminals, etc.;

• plug-in radio devices intended for use within combined equipment, e.g. cable modems, set-top boxes, access

points, etc.;

• combined equipment or a combination of a plug-in radio device and a specific type of host equipment;

• equipment for use in road and rail vehicles;
• ground and wall probing radar equipment;
• (tank) level probing radar equipment;
• material sensing devices.

NOTE: If a system includes transponders, these are measured together with the transmitter and examples of

Ultra-WideBand equipment are given in the related harmonised standards of article 3.2 of Directive

2014/53/EU [i.1].

Technical specifications related to the antenna port and emissions from the enclosure port of Ultra-WideBand (UWB)

equipment are not included in the present document. Such technical specifications are found in the relevant product

standards for the effective use of the radio spectrum.

The present document specifies the applicable test conditions, performance assessment and performance criteria for

Ultra-WideBand (UWB) equipment and associated ancillary equipment.

Examples of Ultra-WideBand equipment are given in the related harmonised standards.

In case of differences (for instance concerning special conditions, definitions, abbreviations) between the present

document and ETSI EN 301 489-1 [1], the provisions of the present document take precedence.

The environmental classification and the emission and immunity requirements used in the present document are as

stated in ETSI EN 301 489-1 [1], except for any special conditions included in the present document.

The present document covers the essential requirements of article 3.1b of Directive 2014/53/EU [i.1] under the

conditions identified in annex A.
2 References
2.1 Normative references

References are specific, identified by date of publication and/or edition number or version number. Only the cited

version applies.

Referenced documents which are not found to be publicly available in the expected location might be found at

https://docbox.etsi.org/Reference/.

NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee

their long term validity.

The following referenced documents are necessary for the application of the present document.

ETSI
---------------------- Page: 6 ----------------------
7 ETSI EN 301 489-33 V2.1.1 (2017-02)

[1] ETSI EN 301 489-1 (V2.1.1) (02-2017): "ElectroMagnetic Compatibility (EMC) standard for

radio equipment and services; Part 1: Common technical requirements; Harmonised Standard

covering the essential requirements of article 3.1(b) of Directive 2014/53/EU and the essential

requirements of article 6 of Directive 2014/30/EU".

[2] ETSI EN 302 065-1 (V2.1.1) (11-2016): "Short Range Devices (SRD) using Ultra Wide Band

technology (UWB); Harmonised Standard covering the essential requirements of article 3.2 of the

Directive 2014/53/EU; Part 1: Requirements for Generic UWB applications".

[3] ETSI EN 302 065-2 (V2.1.1) (11-2016): "Short Range Devices (SRD) using Ultra Wide Band

technology (UWB); Harmonised Standard covering the essential requirements of article 3.2 of the

Directive 2014/53/EU; Part 2: Requirements for UWB location tracking".

[4] ETSI EN 302 065-3 (V2.1.1) (11-2016): "Short Range Devices (SRD) using Ultra Wide Band

technology (UWB); Harmonised Standard covering the essential requirements of article 3.2 of the

Directive 2014/53/EU; Part 3: Requirements for UWB devices for ground based vehicular

applications".

[5] ETSI EN 302 065-4 (V1.1.1) (11-2016): "Short Range Devices (SRD) using Ultra Wide Band

technology (UWB); Harmonised Standard covering the essential requirements of article 3.2 of the

Directive 2014/53/EU; Part 4: Material Sensing devices using UWB technology below 10,6 GHz".

[6] ETSI EN 302 066 (V2.1.1) (01-2017): "Short Range Devices (SRD); Ground- and Wall- Probing

Radar applications (GPR/WPR) imaging systems; Harmonised Standard covering the essential

requirements of article 3.2 of the Directive 2014/53/EU".

[7] ETSI EN 302 372 (V2.1.1) (12-2016): "Short Range Devices (SRD); Tank Level Probing Radar

(TLPR) equipment operating in the frequency ranges 4,5 GHz to 7 GHz, 8,5 GHz to 10,6 GHz,

24,05 GHz to 27 GHz, 57 GHz to 64 GHz, 75 GHz to 85 GHz; Harmonised Standard covering the

essential requirements of article 3.2 of the Directive 2014/53/EU".

[8] ETSI EN 302 729 (V2.1.1) (12-2016): "Short Range Devices (SRD); Level Probing Radar (LPR)

equipment operating in the frequency ranges 6 GHz to 8,5 GHz, 24,05 GHz to 26,5 GHz, 57 GHz

to 64 GHz, 75 GHz to 85 GHz; Harmonised Standard covering the essential requirements of

article 3.2 of the Directive 2014/53/EU".

[9] CENELEC EN 55032:2015: "Electromagnetic compatibility of multimedia equipment - Emission

Requirements".

[10] CENELEC EN 61326-1:2013: "Electrical equipment for measurement, control and laboratory use

- EMC requirements - Part 1: General requirements".

[11] CENELEC EN 61326-2-3:2013: "Electrical equipment for measurement, control and laboratory

use - EMC requirements - Part 2-3: Particular requirements - Test configuration, operational

conditions and performance criteria for transducers with integrated or remote signal conditioning".

[12] CENELEC EN 61326-2-5:2013: "Electrical equipment for measurement, control and laboratory

use - EMC requirements - Part 2-5: Particular requirements - Test configurations, operational

conditions and performance criteria for field devices with interfaces according to IEC 61748-1,

CP 3/2".

[13] CENELEC EN 61000-6-2:2005: "Electromagnetic compatibility (EMC) - Part 6-2: Generic

standards - Immunity for industrial environments".

[14] CENELEC EN 61000-6-3:2007 "Electromagnetic compatibility (EMC) - Part 6-3: Generic

standards -Emission standard for residential, commercial and light-industrial environments".

[15] ETSI EN 303 883 (V1.1.1) (09-2016): "Short Range Devices (SRD) using Ultra Wide Band

(UWB);Measurement Techniques".
ETSI
---------------------- Page: 7 ----------------------
8 ETSI EN 301 489-33 V2.1.1 (2017-02)
2.2 Informative references

References are either specific (identified by date of publication and/or edition number or version number) or

non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the

referenced document (including any amendments) applies.

NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee

their long term validity.

The following referenced documents are not necessary for the application of the present document but they assist the

user with regard to a particular subject area.

[i.1] Directive 2014/53/EU of the European Parliament and of the council of 16 April 2014 on the

harmonisation of the laws of the Member States relating to the making available on the market of

radio equipment and repealing Directive 1999/5/EC.

[i.2] Commission Implementing Decision C(2015) 5376 final of 4.8.2015 on a standardisation request

to the European Committee for Electrotechnical Standardisation and to the European

Telecommunications Standards Institute as regards radio equipment in support of
Directive 2014/53/EU of the European Parliament and of the Council.
3 Definitions and abbreviations
3.1 Definitions

For the purposes of the present document, the terms and definitions given in ETSI EN 301 489-1, clause 3 [1] apply.

3.2 Abbreviations

For the purposes of the present document, the abbreviations given in ETSI EN 301 489-1, clause 3 [1] and in specific

UWB standards ETSI EN 302 065 parts 1 [2], 2 [3], 3 [4] and 4 [5], ETSI EN 302 066 [6], ETSI EN 302 372 [7] and

ETSI EN 302 729 [8] apply.
4 Test conditions
4.1 General

For the purposes of the present document, the test conditions of ETSI EN 301 489-1, clause 4 [1] shall apply as

appropriate. Further product related test conditions for UWB equipment are specified in the present document.

For emission and immunity tests the test modulation, t
...

Final draft ETSI EN 301 489-33 V2.1.1 (2016-11)
HARMONISED EUROPEAN STANDARD
ElectroMagnetic Compatibility (EMC) standard
for radio equipment and services;
Part 33: Specific conditions
for Ultra-WideBand (UWB) devices;
Harmonised Standard covering the essential requirements
of article 3.1(b) of Directive 2014/53/EU
---------------------- Page: 1 ----------------------
2 Final draft ETSI EN 301 489-33 V2.1.1 (2016-11)
Reference
REN/ERM-EMC-343
Keywords
EMC, harmonised standard, radio, UWB
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search

The present document may be made available in electronic versions and/or in print. The content of any electronic and/or

print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any

existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the

print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.

Users of the present document should be aware that the document may be subject to revision or change of status.

Information on the current status of this and other ETSI documents is available at

https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx

If you find errors in the present document, please send your comment to one of the following services:

https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification

No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying

and microfilm except as authorized by written permission of ETSI.

The content of the PDF version shall not be modified without the written authorization of ETSI.

The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2016.
All rights reserved.
TM TM TM

DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.

3GPP and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and

of the 3GPP Organizational Partners.

GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.

ETSI
---------------------- Page: 2 ----------------------
3 Final draft ETSI EN 301 489-33 V2.1.1 (2016-11)
Contents

Intellectual Property Rights ................................................................................................................................ 5

Foreword ............................................................................................................................................................. 5

Modal verbs terminology .................................................................................................................................... 5

1 Scope ........................................................................................................................................................ 6

2 References ................................................................................................................................................ 6

2.1 Normative references ......................................................................................................................................... 6

2.2 Informative references ........................................................................................................................................ 8

3 Definitions and abbreviations ................................................................................................................... 8

3.1 Definitions .......................................................................................................................................................... 8

3.2 Abbreviations ..................................................................................................................................................... 8

4 Test conditions ......................................................................................................................................... 8

4.1 General ............................................................................................................................................................... 8

4.2 Arrangements for test signals ............................................................................................................................. 8

4.2.1 General .......................................................................................................................................................... 8

4.2.2 Arrangements for test signals at the RF input of transmitters ....................................................................... 8

4.2.3 Arrangements for test signals at the RF output of transmitters ..................................................................... 9

4.2.4 Arrangements for test signals at the RF input of receivers ........................................................................... 9

4.2.5 Arrangements for test signals at the RF output of receivers ......................................................................... 9

4.2.6 Arrangements for testing transmitter and receiver together (as a system) .................................................... 9

4.3 Exclusion bands .................................................................................................................................................. 9

4.3.1 for EMC emission test .................................................................................................................................. 9

4.3.2 for EMC immunity test ................................................................................................................................. 9

4.4 Narrow band responses of receivers ................................................................................................................... 9

4.5 Normal test modulation .................................................................................................................................... 10

5 Performance assessment ......................................................................................................................... 10

5.1 General ............................................................................................................................................................. 10

5.2 Equipment which can provide an UWB communications link ......................................................................... 10

5.3 Equipment which does not provide an UWB communications link ................................................................. 10

5.4 Ancillary equipment ......................................................................................................................................... 10

5.5 Equipment classification .................................................................................................................................. 10

6 Performance criteria ............................................................................................................................... 11

6.0 Introduction ...................................................................................................................................................... 11

6.1 Performance criteria for continuous phenomena applied to transmitters and receivers ................................... 11

6.2 Performance criteria for transient phenomena applied to transmitters and receivers ....................................... 11

6.3 Performance criteria for equipment which does not provide an UWB communication link ............................ 11

6.4 Performance criteria for ancillary equipment tested on a stand alone basis ..................................................... 12

7 Applicability overview ........................................................................................................................... 12

7.1 Emission ........................................................................................................................................................... 12

7.2 Immunity .......................................................................................................................................................... 12

8 Methods of measurement and limits for EMC emissions ...................................................................... 12

8.1 Test configuration............................................................................................................................................. 12

8.2 Enclosure port of ancillary equipment measured on a stand alone basis .......................................................... 12

8.2.1 General ........................................................................................................................................................ 12

8.2.2 Test method ................................................................................................................................................ 12

8.2.3 Limits .......................................................................................................................................................... 13

8.3 DC power input/output ports ............................................................................................................................ 13

8.3.1 General ........................................................................................................................................................ 13

8.3.2 Test method ................................................................................................................................................ 13

8.3.3 Limits .......................................................................................................................................................... 13

8.4 AC mains power input/output ports ................................................................................................................. 13

8.4.1 General ........................................................................................................................................................ 13

8.4.2 Test method ................................................................................................................................................ 14

ETSI
---------------------- Page: 3 ----------------------
4 Final draft ETSI EN 301 489-33 V2.1.1 (2016-11)

8.4.3 Limits .......................................................................................................................................................... 14

8.4.3.1 General .................................................................................................................................................. 14

8.4.3.2 AC Power port used for power supply only .......................................................................................... 14

8.4.3.3 AC power input port also used for PLC Communications .................................................................... 14

8.5 Harmonic current emissions (AC mains input port) ......................................................................................... 14

8.6 Voltage fluctuations and flicker (AC mains input port) ................................................................................... 15

8.7 Wired network ports ......................................................................................................................................... 15

8.7.1 General ........................................................................................................................................................ 15

8.7.2 Test method ................................................................................................................................................ 15

8.7.3 Limits .......................................................................................................................................................... 15

9 Test methods and levels for immunity tests ........................................................................................... 15

9.1 Test configuration............................................................................................................................................. 15

9.2 Radio frequency electromagnetic field (80 MHz to 6 000 MHz) ..................................................................... 16

9.2.1 General ........................................................................................................................................................ 16

9.2.2 Test method ................................................................................................................................................ 16

9.2.3 Performance criteria .................................................................................................................................... 16

9.3 Electrostatic discharge ...................................................................................................................................... 16

9.3.1 General ........................................................................................................................................................ 16

9.3.2 Test method ................................................................................................................................................ 16

9.3.3 Performance criteria .................................................................................................................................... 17

9.4 Fast transients, common mode ......................................................................................................................... 17

9.4.1 General ........................................................................................................................................................ 17

9.4.2 Test method ................................................................................................................................................ 17

9.4.3 Performance criteria .................................................................................................................................... 17

9.5 Radio frequency, common mode ...................................................................................................................... 17

9.5.1 General ........................................................................................................................................................ 17

9.5.2 Test method ................................................................................................................................................ 18

9.5.3 Performance criteria .................................................................................................................................... 18

9.6 Transients and surges in the vehicular environment ......................................................................................... 18

9.6.1 General ........................................................................................................................................................ 18

9.6.2 Test method ................................................................................................................................................ 18

9.6.3 Performance criteria .................................................................................................................................... 18

9.7 Voltage dips and interruptions .......................................................................................................................... 19

9.7.1 General ........................................................................................................................................................ 19

9.7.2 Test method ................................................................................................................................................ 19

9.7.3 Performance criteria .................................................................................................................................... 19

9.8 Surges ............................................................................................................................................................... 19

9.8.1 General ........................................................................................................................................................ 19

9.8.2 Test method ................................................................................................................................................ 19

9.8.2.0 General .................................................................................................................................................. 19

9.8.2.1 Test method for wired network ports directly connected to outdoor cables .......................................... 20

9.8.2.2 Test method for wired network ports connected to indoor cables ......................................................... 20

9.8.2.3 Test method for mains ports .................................................................................................................. 20

9.8.3 Performance criteria .................................................................................................................................... 20

Annex A (informative): Relationship between the present document and the essential

requirements of Directive 2014/53/EU ......................................................... 21

Annex B (informative): Change history ............................................................................................... 23

History .............................................................................................................................................................. 24

ETSI
---------------------- Page: 4 ----------------------
5 Final draft ETSI EN 301 489-33 V2.1.1 (2016-11)
Intellectual Property Rights

IPRs essential or potentially essential to the present document may have been declared to ETSI. The information

pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found

in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in

respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web

server (https://ipr.etsi.org/).

Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee

can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web

server) which are, or may be, or may become, essential to the present document.
Foreword

This final draft Harmonised European Standard (EN) has been produced by ETSI Technical Committee

Electromagnetic compatibility and Radio spectrum Matters (ERM), and is now submitted for the Vote phase of the

ETSI standards EN Approval Procedure.

The present document has been prepared under the Commission's standardisation request C(2015) 5376 final [i.2] to

provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation

of the laws of the Member States relating to the making available on the market of radio equipment and repealing

Directive 1999/5/EC [i.1].

Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with

the normative clauses of the present document given in table A.1 confers, within the limits of the scope of the present

document, a presumption of conformity with the corresponding essential requirements of that Directive, and associated

EFTA regulations.

The present document is part 33 of a multi-part deliverable. Full details of the entire series can be found in part 1 [1].

Proposed national transposition dates
Date of latest announcement of this EN (doa): 3 months after ETSI publication
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 6 months after doa

Date of withdrawal of any conflicting National Standard (dow): 18 months after doa

Modal verbs terminology

In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and

"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of

provisions).

"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.

ETSI
---------------------- Page: 5 ----------------------
6 Final draft ETSI EN 301 489-33 V2.1.1 (2016-11)
1 Scope

The present document, together with ETSI EN 301 489-1 [1], specifies technical characteristics and methods of

measurements for radio devices based on UWB technology in respect of ElectroMagnetic Compatibility (EMC).

The present document applies to fixed, mobile or portable UWB devices, e.g.:
• stand alone radio equipment with or without its own control provisions;

• plug-in radio devices intended for use with, or within, a variety of host systems, e.g. personal computers,

hand-held terminals, etc.;

• plug-in radio devices intended for use within combined equipment, e.g. cable modems, set-top boxes, access

points, etc.;

• combined equipment or a combination of a plug-in radio device and a specific type of host equipment;

• equipment for use in road and rail vehicles;
• Ground and wall probing radar equipment;
• (tank) level probing radar equipment;
• Material sensing devices.

NOTE: If a system includes transponders, these are measured together with the transmitter and examples of Ultra-

WideBand equipment are given in the related harmonised standards of article 3.2 of Directive

2014/53/EU.

Technical specifications related to the antenna port and emissions from the enclosure port of Ultra-WideBand (UWB)

equipment are not included in the present document. Such technical specifications are found in the relevant product

standards for the effective use of the radio spectrum.

The present document specifies the applicable test conditions, performance assessment and performance criteria for

Ultra-WideBand (UWB) equipment and associated ancillary equipment.

Examples of Ultra-WideBand equipment are given in the related harmonised standards.

In case of differences (for instance concerning special conditions, definitions, abbreviations) between the present

document and ETSI EN 301 489-1 [1], the provisions of the present document take precedence.

The environmental classification and the emission and immunity requirements used in the present document are as

stated in ETSI EN 301 489-1 [1], except for any special conditions included in the present document.

The present document covers the essential requirements of article 3.1b of Directive 2014/53/EU under the conditions

identified in annex A.
2 References
2.1 Normative references

References are specific, identified by date of publication and/or edition number or version number. Only the cited

version applies.

Referenced documents which are not found to be publicly available in the expected location might be found at

https://docbox.etsi.org/Reference/.

NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee

their long term validity.
ETSI
---------------------- Page: 6 ----------------------
7 Final draft ETSI EN 301 489-33 V2.1.1 (2016-11)

The following referenced documents are necessary for the application of the present document.

[1] ETSI EN 301 489-1 (V2.1.1) (11-2016): "ElectroMagnetic Compatibility (EMC) standard for

radio equipment and services; Part 1: Common technical requirements; Harmonised Standard

covering the essential requirements of article 3.1(b) of Directive 2014/53/EU and the essential

requirements of article 6 of Directive 2014/30/EU".

[2] ETSI EN 302 065-1 (V2.1.1) (11-2016): "Short Range Devices (SRD) using Ultra Wide Band

technology (UWB); Harmonised Standard covering the essential requirements of article 3.2 of the

Directive 2014/53/EU; Part 1: Requirements for Generic UWB applications".

[3] ETSI EN 302 065-2 (V2.1.1) (11-2016): "Short Range Devices (SRD) using Ultra Wide Band

technology (UWB); Harmonised Standard covering the essential requirements of article 3.2 of the

Directive 2014/53/EU; Part 2: Requirements for UWB location tracking".

[4] ETSI EN 302 065-3 (V2.1.1) (11-2016): "Short Range Devices (SRD) using Ultra Wide Band

technology (UWB); Harmonised Standard covering the essential requirements of article 3.2 of the

Directive 2014/53/EU; Part 3: Requirements for UWB devices for ground based vehicular

applications".

[5] ETSI EN 302 065-4 (V1.1.1) (11-2016): "Short Range Devices (SRD) using Ultra Wide Band

technology (UWB); Harmonised Standard covering the essential requirements of article 3.2 of the

Directive 2014/53/EU; Part 4: Material Sensing devices using UWB technology below 10,6 GHz".

[6] ETSI EN 302 066 (V2.1.1) (10-2016): "Short Range Devices (SRD); Ground- and Wall- Probing

Radar applications (GPR/WPR) imaging systems; Harmonised Standard covering the essential

requirements of article 3.2 of the Directive 2014/53/EU".

[7] ETSI EN 302 372 (V2.1.1) (10-2016): "Short Range Devices (SRD); Tank Level Probing Radar

(TLPR) equipment operating in the frequency ranges 4,5 GHz to 7 GHz, 8,5 GHz to 10,6 GHz,

24,05 GHz to 27 GHz, 57 GHz to 64 GHz, 75 GHz to 85 GHz; Harmonised Standard covering the

essential requirements of article 3.2 of the Directive 2014/53/EU.".

[8] ETSI EN 302 729 (V2.1.1) (10-2016): "Short Range Devices (SRD); Level Probing Radar (LPR)

equipment operating in the frequency ranges 6 GHz to 8,5 GHz, 24,05 GHz to 26,5 GHz, 57 GHz

to 64 GHz, 75 GHz to 85 GHz; Harmonised Standard covering the essential requirements of

article 3.2 of the Directive 2014/53/EU".

[9] CENELEC EN 55032:2015: "Electromagnetic compatibility of multimedia equipment - Emission

Requirements".

[10] CENELEC EN 61326-1:2013: "Electrical equipment for measurement, control and laboratory use

- EMC requirements - Part 1: General requirements".

[11] CENELEC EN 61326-2-3:2013: "Electrical equipment for measurement, control and laboratory

use - EMC requirements - Part 2-3: Particular requirements - Test configuration, operational

conditions and performance criteria for transducers with integrated or remote signal conditioning".

[12] CENELEC EN 61326-2-5:2013: "Electrical equipment for measurement, control and laboratory

use - EMC requirements - Part 2-5: Particular requirements - Test configurations, operational

conditions and performance criteria for field devices with interfaces according to IEC 61748-1,

CP 3/2".

[13] CENELEC EN 61000-6-2:2005: "Electromagnetic compatibility (EMC) - Part 6-2: Generic

standards - Immunity for industrial environments".

[14] CENELEC EN 61000-6-3:2007 "Electromagnetic compatibility (EMC) - Part 6-3: Generic

standards -Emission standard for residential, commercial and light-industrial environments".

[15] ETSI EN 303 883 (V1.1.1) (09-2016): "Short Range Devices (SRD) using Ultra Wide Band

(UWB);Measurement Techniques".
ETSI
---------------------- Page: 7 ----------------------
8 Final draft ETSI EN 301 489-33 V2.1.1 (2016-11)
2.2 Informative references

References are either specific (identified by date of publication and/or edition number or version number) or

non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the

referenced document (including any amendments) applies.

NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee

their long term validity.

The following referenced documents are not necessary for the application of the present document but they assist the

user with regard to a particular subject area.

[i.1] Directive 2014/53/EU of the European Parliament and of the council of 16 April 2014 on the

harmonisation of the laws of the Member States relating to the making available on the market of

radio equipment and repealing Directive 1999/5/EC.

[i.2] Commission Implementing Decision C(2015) 5376 final of 4.8.2015 on a standardisation request

to the European Committee for Electrotechnical Standardisation and to the European

Telecommunications Standards Institute as regards radio equipment in support of
Directive 2014/53/EU of the European Parliament and of the Council.
3 Definitions and abbreviations
3.1 Definitions

For the purposes of the present document, the terms and definitions given in ETSI EN 301 489-1, clause 3 [1] apply.

3.2 Abbreviations

For the purposes of the present document, the abbreviations given of ETSI EN 301 489-1, in clause 3 [1] and in specific

UWB standards ETSI EN 302 065 parts 1 [2], 2 [3], 3 [4] and 4 [5], ETSI EN 302 066 [6], ETSI EN 302 372 [7] and

ETSI EN 302 729 [8] apply.
4 Test conditions
4.1 General

For the purposes of the present document, the test conditions of ETSI EN 301 489-1, clause 4 [

...

Draft ETSI EN 301 489-33 V2.1.0 (2016-04)
HARMONISED EUROPEAN STANDARD
ElectroMagnetic Compatibility (EMC) standard
for radio equipment and services;
Part 33: Specific conditions
for Ultra-WideBand (UWB) devices;
Harmonised Standard covering the essential requirements
of article 3.1(b) of the Directive 2014/53/EU
---------------------- Page: 1 ----------------------
2 Draft ETSI EN 301 489-33 V2.1.0 (2016-04)
Reference
REN/ERM-EMC-343
Keywords
EMC, harmonised standard, radio, UWB
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search

The present document may be made available in electronic versions and/or in print. The content of any electronic and/or

print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any

existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the

print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.

Users of the present document should be aware that the document may be subject to revision or change of status.

Information on the current status of this and other ETSI documents is available at

https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx

If you find errors in the present document, please send your comment to one of the following services:

https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification

No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying

and microfilm except as authorized by written permission of ETSI.

The content of the PDF version shall not be modified without the written authorization of ETSI.

The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2016.
All rights reserved.
TM TM TM

DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.

3GPP and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and

of the 3GPP Organizational Partners.

GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.

ETSI
---------------------- Page: 2 ----------------------
3 Draft ETSI EN 301 489-33 V2.1.0 (2016-04)
Contents

Intellectual Property Rights ................................................................................................................................ 5

Foreword ............................................................................................................................................................. 5

Modal verbs terminology .................................................................................................................................... 5

1 Scope ........................................................................................................................................................ 6

2 References ................................................................................................................................................ 6

2.1 Normative references ......................................................................................................................................... 6

2.2 Informative references ........................................................................................................................................ 7

3 Definitions and abbreviations ................................................................................................................... 8

3.1 Definitions .......................................................................................................................................................... 8

3.2 Abbreviations ..................................................................................................................................................... 8

4 Test conditions ......................................................................................................................................... 8

4.1 General ............................................................................................................................................................... 8

4.2 Arrangements for test signals ............................................................................................................................. 8

4.2.1 General .......................................................................................................................................................... 8

4.2.2 Arrangements for test signals at the input of transmitters ............................................................................. 8

4.2.3 Arrangements for test signals at the output of transmitters ........................................................................... 8

4.2.4 Arrangements for test signals at the input of receivers ................................................................................. 8

4.2.5 Arrangements for test signals at the output of receivers ............................................................................... 8

4.2.6 Arrangements for testing transmitter and receiver together (as a system) .................................................... 8

4.3 Exclusion bands .................................................................................................................................................. 9

4.4 Narrow band responses of receivers ................................................................................................................... 9

4.5 Normal test modulation ...................................................................................................................................... 9

5 Performance assessment ........................................................................................................................... 9

5.1 General ............................................................................................................................................................... 9

5.2 Equipment which can provide an UWB communications link ........................................................................... 9

5.3 Equipment which does not provide an UWB communications link ................................................................... 9

5.4 Ancillary equipment ........................................................................................................................................... 9

5.5 Equipment classification .................................................................................................................................... 9

6 Performance criteria ............................................................................................................................... 10

6.0 Introduction ...................................................................................................................................................... 10

6.1 Performance criteria for continuous phenomena applied to transmitters and receivers ................................... 10

6.2 Performance criteria for transient phenomena applied to transmitters and receivers ....................................... 10

6.3 Performance criteria for equipment which does not provide an UWB communication link ............................ 10

6.4 Performance criteria for ancillary equipment tested on a stand alone basis ..................................................... 10

7 Applicability overview ........................................................................................................................... 10

7.1 Emission ........................................................................................................................................................... 10

7.2 Immunity .......................................................................................................................................................... 10

8 Methods of measurement and limits for EMC emissions ...................................................................... 11

8.1 Test configuration............................................................................................................................................. 11

8.2 Enclosure port of ancillary equipment measured on a stand alone basis .......................................................... 11

8.2.1 General ........................................................................................................................................................ 11

8.2.2 Test method ................................................................................................................................................ 11

8.2.3 Limits .......................................................................................................................................................... 11

8.3 DC power input/output ports ............................................................................................................................ 11

8.3.1 General ........................................................................................................................................................ 11

8.3.2 Test method ................................................................................................................................................ 11

8.3.3 Limits .......................................................................................................................................................... 11

8.4 AC mains power input/output ports ................................................................................................................. 11

8.4.1 General ........................................................................................................................................................ 11

8.4.2 Test method ................................................................................................................................................ 12

8.4.3 Limits .......................................................................................................................................................... 12

8.4.3.1 General .................................................................................................................................................. 12

ETSI
---------------------- Page: 3 ----------------------
4 Draft ETSI EN 301 489-33 V2.1.0 (2016-04)

8.4.3.2 AC Power port used for power supply only .......................................................................................... 12

8.4.3.3 AC power input port also used for PLC Communications .................................................................... 12

8.5 Harmonic current emissions (AC mains input port) ......................................................................................... 12

8.6 Voltage fluctuations and flicker (AC mains input port) ................................................................................... 12

8.7 Wired network ports ......................................................................................................................................... 12

8.7.1 General ........................................................................................................................................................ 12

8.7.2 Test method ................................................................................................................................................ 12

8.7.3 Limits .......................................................................................................................................................... 12

9 Test methods and levels for immunity tests ........................................................................................... 13

9.1 Test configuration............................................................................................................................................. 13

9.2 Radio frequency electromagnetic field (80 MHz to 6 000 MHz) ..................................................................... 13

9.2.1 General ........................................................................................................................................................ 13

9.2.2 Test method ................................................................................................................................................ 13

9.2.3 Performance criteria .................................................................................................................................... 13

9.3 Electrostatic discharge ...................................................................................................................................... 13

9.3.1 General ........................................................................................................................................................ 13

9.3.2 Test method ................................................................................................................................................ 13

9.3.3 Performance criteria .................................................................................................................................... 13

9.4 Fast transients, common mode ......................................................................................................................... 13

9.4.1 General ........................................................................................................................................................ 13

9.4.2 Test method ................................................................................................................................................ 14

9.4.3 Performance criteria .................................................................................................................................... 14

9.5 Radio frequency, common mode ...................................................................................................................... 14

9.5.1 General ........................................................................................................................................................ 14

9.5.2 Test method ................................................................................................................................................ 14

9.5.3 Performance criteria .................................................................................................................................... 14

9.6 Transients and surges in the vehicular environment ......................................................................................... 14

9.6.1 General ........................................................................................................................................................ 14

9.6.2 Test method ................................................................................................................................................ 14

9.6.3 Performance criteria .................................................................................................................................... 14

9.7 Voltage dips and interruptions .......................................................................................................................... 14

9.7.1 General ........................................................................................................................................................ 14

9.7.2 Test method ................................................................................................................................................ 15

9.7.3 Performance criteria .................................................................................................................................... 15

9.8 Surges ............................................................................................................................................................... 15

9.8.1 General ........................................................................................................................................................ 15

9.8.2 Test method ................................................................................................................................................ 15

9.8.2.0 General .................................................................................................................................................. 15

9.8.2.1 Test method for wired network ports directly connected to outdoor cables .......................................... 15

9.8.2.2 Test method for wired network ports connected to indoor cables ......................................................... 15

9.8.2.3 Test method for mains ports .................................................................................................................. 15

9.8.3 Performance criteria .................................................................................................................................... 15

Annex A (normative): Relationship between the present document and the essential

requirements of Directive 2014/53/EU ......................................................... 16

History .............................................................................................................................................................. 18

ETSI
---------------------- Page: 4 ----------------------
5 Draft ETSI EN 301 489-33 V2.1.0 (2016-04)
Intellectual Property Rights

IPRs essential or potentially essential to the present document may have been declared to ETSI. The information

pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found

in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in

respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web

server (https://ipr.etsi.org/).

Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee

can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web

server) which are, or may be, or may become, essential to the present document.
Foreword

This draft Harmonised European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic

compatibility and Radio spectrum Matters (ERM), and is now submitted for the combined Public Enquiry and Vote

phase of the ETSI standards EN Approval Procedure.

The present document has been prepared under the Commission's standardisation request C(2015) 5376 final [i.2] to

provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation

of the laws of the Member States relating to the making available on the market of radio equipment and repealing

Directive 1999/5/EC [i.1].

Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with

the normative clauses of the present document given in table A.1 confers, within the limits of the scope of the present

document, a presumption of conformity with the corresponding essential requirements of that Directive, and associated

EFTA regulations.

The present document is part 33 of a multi-part deliverable. Full details of the entire series can be found in part 1 [1].

Proposed national transposition dates
Date of latest announcement of this EN (doa): 3 months after ETSI publication
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 6 months after doa

Date of withdrawal of any conflicting National Standard (dow): 18 months after doa

Modal verbs terminology

In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and

"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of

provisions).

"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.

ETSI
---------------------- Page: 5 ----------------------
6 Draft ETSI EN 301 489-33 V2.1.0 (2016-04)
1 Scope

The present document, together with ETSI EN 301 489-1 [1], covers the assessment of radio devices based on UWB

technology in respect of ElectroMagnetic Compatibility (EMC).
The present document applies to fixed, mobile or portable UWB devices, e.g.:
• stand alone radio equipment with or without its own control provisions;

• plug-in radio devices intended for use with, or within, a variety of host systems, e.g. personal computers,

hand-held terminals, etc.;

• plug-in radio devices intended for use within combined equipment, e.g. cable modems, set-top boxes, access

points, etc.;

• combined equipment or a combination of a plug-in radio device and a specific type of host equipment;

• equipment for use in road and rail vehicles;
• Ground and wall probing radar equipment;
• (tank) level probing radar equipment;
• Material sensing devices.

Technical specifications related to the antenna port and emissions from the enclosure port of Ultra-WideBand (UWB)

equipment are not included in the present document. Such technical specifications are found in the relevant product

standards for the effective use of the radio spectrum.

The present document specifies the applicable test conditions, performance assessment and performance criteria for

Ultra-WideBand (UWB) equipment and associated ancillary equipment.

Examples of Ultra-WideBand equipment are given in the related harmonised standards.

In case of differences (for instance concerning special conditions, definitions, abbreviations) between the present

document and ETSI EN 301 489-1 [1], the provisions of the present document take precedence.

The environmental classification and the emission and immunity requirements used in the present document are as

stated in ETSI EN 301 489-1 [1], except for any special conditions included in the present document.

2 References
2.1 Normative references

References are either specific (identified by date of publication and/or edition number or version number) or

non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the

referenced document (including any amendments) applies.

Referenced documents which are not found to be publicly available in the expected location might be found at

https://docbox.etsi.org/Reference/.

NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee

their long term validity.

The following referenced documents are necessary for the application of the present document.

[1] ETSI EN 301 489-1 (V2.1.0) (04-2016): "ElectroMagnetic Compatibility (EMC) standard for

radio equipment and services; Harmonised Standard covering the essential requirements of

article 3.1(b) of the Directive 2014/53/EU and the essential requirements of article 6 of the

Directive 2014/30/EU; Part 1: Common technical requirements".
ETSI
---------------------- Page: 6 ----------------------
7 Draft ETSI EN 301 489-33 V2.1.0 (2016-04)

[2] ETSI EN 302 065-1 (V2.1.0) (04-2016): "Short Range Devices (SRD) using Ultra Wide Band

technology (UWB); Harmonised Standard covering the essential requirements of article 3.2 of the

Directive 2014/53/EU; Part 1: Requirements for Generic UWB applications".

[3] ETSI EN 302 065-2 (V2.1.0) (04-2016): "Short Range Devices (SRD) using Ultra Wide Band

technology (UWB); Harmonised Standard covering the essential requirements of article 3.2 of the

Directive 2014/53/EU; Part 2: Requirements for UWB location tracking".

[4] ETSI EN 302 065-3 (V2.1.0) (04-2016): "Short Range Devices (SRD) using Ultra Wide Band

technology (UWB); Harmonised Standard covering the essential requirements of article 3.2 of the

Directive 2014/53/EU; Part 3: Requirements for UWB devices for ground based vehicular

applications".

[5] ETSI EN 302 065-4 (V1.1.0) (04-2016): "Short Range Devices (SRD) using Ultra Wide Band

technology (UWB); Harmonised Standard covering the essential requirements of article 3.2 of the

Directive 2014/53/EU; Part 4: Material Sensing devices using UWB technology below 10,6 GHz".

[6] ETSI EN 302 066 (V2.1.0) (04-2016): "Short Range Devices (SRD); Ground- and Wall- Probing

Radar applications (GPR/WPR) imaging systems; Harmonised Standard covering the essential

requirements of article 3.2 of the Directive 2014/53/EU".

[7] ETSI EN 302 372 (V2.1.0) (04-2016): "Short Range Devices (SRD); Equipment for Detection and

Movement; Tank Level Probing Radar (TLPR) equipment operating in the frequency ranges

4,5 GHz to 7 GHz, 8,5 GHz to 10,6 GHz, 24,05 GHz to 27 GHz, 57 GHz to 64 GHz, 75 GHz to

85 GHz Harmonised Standard covering the essential requirements of article 3.2 of the Directive

2014/53/EU".

[8] ETSI EN 302 729 (V2.1.0) (04-2016): "Short Range Devices (SRD); Level Probing Radar (LPR)

equipment operating in the frequency ranges 6 GHz to 8,5 GHz, 24,05 GHz to 26,5 GHz, 57 GHz

to 64 GHz, 75 GHz to 85 GHz; Harmonised Standard covering the essential requirements of

article 3.2 of the Directive 2014/53/EU".

[9] CENELEC EN 55032:2015: "Electromagnetic compatibility of multimedia equipment - Emission

Requirements".

[10] CENELEC EN 61326-1:2013: "Electrical equipment for measurement, control and laboratory use

- EMC requirements - Part 1: General requirements".

[11] CENELEC EN 61326-2-3:2013: "Electrical equipment for measurement, control and laboratory

use - EMC requirements - Part 2-3: Particular requirements - Test configuration, operational

conditions and performance criteria for transducers with integrated or remote signal conditioning".

2.2 Informative references

References are either specific (identified by date of publication and/or edition number or version number) or

non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the

referenced document (including any amendments) applies.

NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee

their long term validity.

The following referenced documents are not necessary for the application of the present document but they assist the

user with regard to a particular subject area.

[i.1] Directive 2014/53/EU of the European Parliament and of the council of 16 April 2014 on the

harmonisation of the laws of the Member States relating to the making available on the market of

radio equipment and repealing Directive 1999/5/EC.

[i.2] Commission Implementing Decision C(2015) 5376 final of 4.8.2015 on a standardisation request

to the European Committee for Electrotechnical Standardisation and to the European

Telecommunications Standards Institute as regards radio equipment in support of Directive

2014/53/EU of the European Parliament and of the Council.
ETSI
---------------------- Page: 7 ----------------------
8 Draft ETSI EN 301 489-33 V2.1.0 (2016-04)
3 Definitions and abbreviations
3.1 Definitions

For the purposes of the present document, the terms and definitions given in clause 3 of ETSI EN 301 489-1 [1] apply.

3.2 Abbreviations

For the purposes of the present document, the abbreviations given in clause 3 of ETSI EN 301 489-1 [1] and in specific

UWB standards [2], [3], [4], [5], [6], [7] and [8] apply.
4 Test conditions
4.1 General

For the purposes of the present document, the test conditions of ETSI EN 301 489-1 [1], clause 4 shall apply as

appropriate. Further product related test conditions for UWB equipment are specified in the present document.

For emission and immunity tests the test modulation, test arrangements, etc., as specified in the present document,

clauses 4.1 to 4.5, shall apply.
4.2 Arrangements for test signals
4.2.1 General
The provisions of ETSI EN 301 489-1 [1], clause 4.2 shall apply.
4.2.2 Arrangements for test signals at the input of transmitters
The provisions of ETSI EN 301 489-1 [1], clause 4.2.1 shall apply.
4.2.3 Arrangements for test signals at the output of transmitters

The provisions of ETSI EN 301 489-1 [1], clause 4.2.2 shall apply with the following modification.

The transmitter shall be operated at its maximum rated RF output power, modulated with normal test modulation

(see clause 4.5).
4.2.4 Arrangements for test signals at the input of receivers

The provisions of ETSI EN 301 489-1 [1], clause 4.2.3 shall apply with the following modification.

A communication link shall be established at the start of the test and maintained during the test.

4.2.5 Arrangements for test signals at the output of receivers
The provisions of ETSI EN 301 489-1 [1], clause 4.2.4 shall apply.
4.2.6 Arrangements for testing transmitter and receiver together
(as a system)

The provisions of ETSI EN 301 489-1 [1], clause 4.2.5 shall apply with the following modification.

For the immunity tests of duplex transceivers, the EUT may be configured in the repeater

...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.