SIST EN 16867:2020+A1:2022
(Main)Building hardware - Mechatronic door furniture - Requirements and test methods
Building hardware - Mechatronic door furniture - Requirements and test methods
1.1 General
This document applies to Mechatronic door furniture (MDF) fitted on the door set which gives the possibility to control the locking and/or release part through an electronic authorization means. This can be operable by credentials (i.e. card, code, biometric).
The MDF according to this document is combined with locks according to EN 12209, EN 14846, prEN 15685 or may be a part of an emergency exit device according to EN 179, EN 1125 or EN 13637.
The MDF may be standalone or linkable to an external control system.
The document would allow classifying the MDF upon several characteristics such as category of use, durability, environmental, security, and type of operating device.
The suitability of the MDF for use on fire or smoke-door assemblies is determined by fire resistance tests conducted in addition to the performance testing specified by this document.
1.2 Exclusions
This document does not cover:
- mechatronic cylinders according to EN 15684;
- electromechanical operated locks and striking plates according to EN 14846.
Schlösser und Baubeschläge - Mechatronische Türbeschläge - Anforderungen und Prüfverfahren
1.1 Allgemeines
Dieses Dokument gilt für an der Tür angebrachte mechatronische Türbeschläge (MDF, en. mechatronic door furniture), die die Möglichkeit eröffnen, den Schließ und/oder Öffnungsvorgang durch eine elektronische Freigabeberechtigung zu steuern. Das kann durch Berechtigungsnachweise erfolgen (d. h. Karte, Code, biometrisch).
Der diesem Dokument entsprechende MDF wird mit Schlössern nach EN 12209, EN 14846, EN 15685 kombiniert oder kann Teil eines Notausgangverschlusses nach EN 179, EN 1125 oder EN 13637 sein.
Der MDF kann eigenständig ausgeführt sein oder mit einem externen Steuersystem verbunden werden.
Das Dokument würde es ermöglichen, die MDF mittels mehrerer Eigenschaften, wie etwa Gebrauchskategorie, Dauerfunktionstüchtigkeit, Umweltbeständigkeit, Schutz und Typ der Betätigungsvorrichtung zu klassifizieren.
Die Eignung des MDF für die Verwendung an Feuer oder Rauchschutzeinbauten wird durch Prüfungen des Feuerwiderstands bestimmt, die zusätzlich zu den in diesem Dokument festgelegten Leistungsprüfungen durchgeführt werden.
1.2 Ausnahmen
Dieses Dokument behandelt nicht:
- mechatronische Schließzylinder nach EN 15684;
- elektromechanisch betätigte Schlösser und Schließbleche nach EN 14846.
Quincaillerie pour le bâtiment - Poignée de porte mécatronique - Exigences et méthodes d'essai
1.1 Généralités
Le présent document s’applique aux ensembles plaques béquilles mécatroniques (MDF) montés sur un bloc-porte permettant de contrôler l'élément de verrouillage et/ou de déverrouillage sur une ouverture de porte d'un dispositif d'autorisation électronique. Ils peuvent être manœuvrés par des authentifiants (c'est-à-dire une carte, un code, la biométrique).
Le MDF conforme au présent document est combiné à des serrures conformes à l’EN 12209, l’EN 14846, l’EN 15685 ou peut faire partie d'un dispositif de sortie de secours selon l’EN 179, l’EN 1125 ou l’EN 13637.
Un MDF peut être indépendant ou raccordable à un système de contrôle externe.
Le présent document permet de classer les MDF en fonction de plusieurs caractéristiques telles que la catégorie d'utilisation, la durabilité, l'environnement, la sécurité, et le type de dispositif de manœuvre.
L’aptitude des MDF à l’utilisation sur des blocs-blocs-portes coupe-feu et/ou étanches aux fumées est déterminée par des essais de résistance au feu, qui s’ajoutent aux essais de performance spécifiés dans le présent document.
1.2 Exclusions
Le présent document ne couvre pas :
- les cylindres mécatroniques conformes à l’EN 15684 ;
- les serrures et gâches électromécaniques conformes à l’EN 14846.
Stavbno okovje - Mehatronsko okovje za vrata - Zahteve in preskusne metode (vključuje dopolnilo A1)
1.1 Splošno
Ta dokument se uporablja za mehatronsko okovje za vrata (MDF), nameščeno na vratni sklop, ki omogoča nadzor dela za zaklepanje in/ali odklepanje prek sredstev za elektronsko avtorizacijo. To je mogoče upravljati s poverilnicami (tj. kartica, koda, biometrija).
Mehatronsko okovje za vrata se skladno s tem dokumentom uporablja v kombinaciji s ključavnicami v skladu s standardi EN 12209, EN 14846 in prEN 15685 oziroma je lahko del naprave za zasilni izhod v skladu s standardom EN 179, EN 1125 ali EN 13637.
Mehatronsko okovje za vrata je lahko samostojno ali povezano z zunanjim nadzornim sistemom.
Dokument bi omogočal razvrstitev mehatronskega okovja za vrata po različnih značilnostih, kot so kategorija uporabe, trajnost, vpliv na okolje, varnost in vrsta naprave za upravljanje.
Ustreznost mehatronskega okovja za vrata za uporabo pri sestavih požarnih ali dimnih vrat se določi s preskusi požarne odpornosti, ki se izvajajo poleg preskušanja delovanja, določenega v tem dokumentu.
1.2 Izključitve
Ta dokument ne zajema:
– mehatronskih cilindrov v skladu s standardom EN 15684;
– elektromehanskih ključavnic in zapornih plošč v skladu s standardom EN 14846.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 16867:2020+A1:2022
01-januar-2022
Stavbno okovje - Mehatronsko okovje za vrata - Zahteve in preskusne metode
(vključuje dopolnilo A1)
Building hardware - Mechatronic door furniture - Requirements and test methods
Schlösser und Baubeschläge - Mechatronische Türbeschläge - Anforderungen und
Prüfverfahren
Quincaillerie pour le bâtiment - Poignée de porte mécatronique - Exigences et méthodes
d'essai
Ta slovenski standard je istoveten z: EN 16867:2020+A1:2021
ICS:
91.190 Stavbna oprema Building accessories
SIST EN 16867:2020+A1:2022 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 16867:2020+A1:2022
---------------------- Page: 2 ----------------------
SIST EN 16867:2020+A1:2022
EN 16867:2020+A1
EUROPEAN STANDARD
NORME EUROPÉENNE
November 2021
EUROPÄISCHE NORM
ICS 91.190 Supersedes EN 16867:2020
English Version
Building hardware - Mechatronic door furniture -
Requirements and test methods
Quincaillerie pour le bâtiment - Poignée de porte Schlösser und Baubeschläge - Mechatronische
mécatronique - Exigences et méthodes d'essai Türbeschläge - Anforderungen und Prüfverfahren
This European Standard was approved by CEN on 27 January 2020 and includes Amendment 1 approved by CEN on 22
September 2021.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2021 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 16867:2020+A1:2021 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN 16867:2020+A1:2022
EN 16867:2020+A1:2021 (E)
Contents Page
European foreword . 3
Introduction . 3
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 7
4 Requirements . 10
5 Test — general and test apparatus . 27
6 Test methods — procedures . 27
7 Classification system . 54
8 Marking . 56
Annex A (normative) MDF suitable for use on fire resistant / smoke control doors . 57
Annex B (normative) Tool sets for attack resistance tests . 58
Annex C (informative) Table of test procedures . 60
Annex D (informative) Manufacturer’s declaration of compliance . 62
Annex E (informative) Examples of calculation of effective code variations for ICC . 64
Bibliography . 66
2
---------------------- Page: 4 ----------------------
SIST EN 16867:2020+A1:2022
EN 16867:2020+A1:2021 (E)
European foreword
This document (EN 16867:2020+A1:2021) has been prepared by Technical Committee CEN/TC 33
“Doors, windows, shutters, building hardware and curtain walling”, the secretariat of which is held by
AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by May 2021, and conflicting national standards shall be
withdrawn at the latest by May 2021.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document includes Amendment 1 approved by CEN on 22 September 2021.
This document supersedes EN 16867:2020.
The start and finish of text introduced or altered by amendment is indicated in the text by tags !" .
This document is one of a series of European Standards dedicated to building hardware products.
European Standards for mechanically operated lever handles and knob furniture (EN 1906) are also
available.
The performance tests incorporated in this document are considered to be reproducible and as such will
provide a consistent and objective assessment of the performance of these products throughout CEN
Member.
Any feedback and questions on this document should be directed to the users’ national standards body.
A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organisations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia,
Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland,
Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of North
Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United
Kingdom.
3
---------------------- Page: 5 ----------------------
SIST EN 16867:2020+A1:2022
EN 16867:2020+A1:2021 (E)
Introduction
The development of building hardware to include electrically and electronic operations and control has
introduced a large number of products on the market.
For locks and door furniture, the range of electrical or electronic components to be fitted to existing
mechanical locks or door furniture to a complete Mechatronic Door Furniture (MDF) has increased.
Also, complete units with lock and door furniture in unique combination to MDF occur frequently.
Typically, MDF is installed directly on the door leaf and includes all functions like operating the follower
of the lock, reading and decoding the credential and power.
Following components and units are covered by this document.
Type A: Handle or knob operated door furniture with electrically operated actuator, reading unit for
credential and power supply to be combined with a mechanical operated lock where the lock meets
EN 12209 or EN 15685.
Type B: Handle or knob operated door furniture with reading unit for credential and power supply to be
combined with electrically operated locks where the lock meets EN 14846.
This document does not cover electrically operated locks or striking plates in combination with an access
control system not fitted on the door.
This document provides the MDF with requirements for:
— category of use to ensure the performance during its normal use;
— durability to ensure good performance during lifetime;
— specification for system management;
— suitability for use on fire resistant/smoke controlled doors;
— environmental resistance for good performance during lifetime in different environmental
conditions;
— security for different types of credentials;
— attack resistance to ensure use on Burglary resistant doors;
— product information to give summary of the performance.
The performance tests incorporated in this document are considered to be reproducible and as such will
provide a consistent and objective assessment of the performance of these devices throughout CEN
Member States.
It is assumed that MDF will conform to the legal regulations i.e. RED – Radio Equipment Directive
2014/53/EU.
On occasion, there could be a need for additional functions within the design of the MDF. Purchasers
should convince themselves that the products are suitable for their intended use. This is particularly
important when the operation of such additional functions is safety-related. Accordingly, this document
includes assessment of such features when they are included in the MDF design.
4
---------------------- Page: 6 ----------------------
SIST EN 16867:2020+A1:2022
EN 16867:2020+A1:2021 (E)
1 Scope
1.1 General
This document applies to Mechatronic door furniture (MDF) fitted on the door set which gives the
possibility to control the locking and/or release part through an electronic authorization means. This can
be operable by credentials (i.e. card, code, biometric).
The MDF, according to this document, is combined with locks according to EN 12209, EN 14846,
EN 15685 or can be a part of an emergency exit device according to EN 179, EN 1125 or EN 13637.
The MDF can be standalone or linkable to an external control system.
The document would allow classifying the MDF upon several characteristics such as category of use,
durability, environmental, security, and type of operating device.
The suitability of the MDF for use on fire or smoke-door assemblies is determined by fire resistance tests
conducted in addition to the performance testing specified by this document.
1.2 Exclusions
This document does not cover:
— mechatronic cylinders according to EN 15684;
— electromechanical operated locks and striking plates according to EN 14846.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
EN 636:2012+A1:2015, Plywood — Specifications
EN 1303, Building hardware — Cylinders for locks - Requirements and test methods
EN 1634-1, Fire resistance and smoke control tests for door and shutter assemblies, openable windows and
elements of building hardware — Part 1: Fire resistance test for door and shutter assemblies and openable
windows
EN 1634-2, Fire resistance and smoke control tests for door, shutter and openable window assemblies and
elements of building hardware — Part 2: Fire resistance characterisation test for elements of building
hardware
EN 1634-3, Fire resistance and smoke control tests for door and shutter assemblies, openable windows and
elements of building hardware — Part 3: Smoke control test for door and shutter assemblies
EN 1670:2007, Building hardware — Corrosion resistance — Requirements and test methods
EN 1906:2012, Building hardware — Lever handles and knob furniture — Requirements and test methods
EN 14846, Building hardware — Locks and latches — Electromechanically operated locks and striking
plates - Requirements and test methods
EN 15684, Building hardware — Mechatronic cylinders — Requirements and test methods
5
---------------------- Page: 7 ----------------------
SIST EN 16867:2020+A1:2022
EN 16867:2020+A1:2021 (E)
EN 15685, Building hardware — Requirements and test methods — Multipoint locks, latches and locking
plates — Characteristics and test methods
EN 60068-2-1, Environmental testing — Part 2-1: Tests — Test A: Cold
EN 60068-2-2, Environmental testing — Part 2-2: Tests — Test B: Dry heat
EN 60068-2-6, Environmental testing — Part 2-6: Tests — Test Fc: Vibration (sinusoidal)
EN 60068-2-27, Environmental testing — Part 2-27: Tests — Test Ea and guidance: Shock
EN 60068-2-30, Environmental testing — Part 2-30: Tests — Test Db and guidance: Damp heat, cyclic (12
+ 12 hour cycle)
EN 60529, Degrees of protection provided by enclosures (IP Code)
EN 61000-4-2, Electromagnetic compatibility (EMC) — Part 4-2: Testing and measurement techniques -
Electrostatic discharge immunity test
EN 61000-4-3, Electromagnetic compatibility (EMC) — Part 4-3: Testing and measurement techniques —
Radiated, radio-frequency, electromagnetic field immunity test
EN 61000-4-4, Electromagnetic compatibility (EMC) — Part 4-4: Testing and measurement techniques —
Electrical fast transient/burst immunity test
EN 61000-4-5, Electromagnetic compatibility (EMC) — Part 4-5: Testing and measurement techniques —
Surge immunity test
EN 61000-4-11, Electromagnetic compatibility (EMC) — Part 4-11: Testing and measurement techniques -
Voltage dips, short interruptions and voltage variations immunity tests
EN 61000-4-29, Electromagnetic compatibility (EMC) - Part 4-29: Testing and measurement techniques -
Voltage dips, short interruptions and voltage variations on d.c. input power port immunity tests
EN ISO 10666, Drilling screws with tapping screw thread — Mechanical and functional properties
(ISO 10666)
EN ISO 15480, Fasteners — Hexagon washer head drilling screws with tapping screw thread (ISO 15480)
EN ISO 15481, Cross recessed pan head drilling screws with tapping screw thread (ISO 15481)
EN ISO 15482, Cross recessed countersunk head drilling screws with tapping screw thread (ISO 15482)
EN ISO 15483, Cross recessed raised countersunk head drilling screws with tapping screw thread
(ISO 15483)
ISO/IEC 18033-3, Information technology — Security techniques — Encryption algorithms — Part 3: Block
ciphers
ISO 10899, High-speed steel two-flute twist drills - Technical specifications
6
---------------------- Page: 8 ----------------------
SIST EN 16867:2020+A1:2022
EN 16867:2020+A1:2021 (E)
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— IEC Electropedia: available at https://www.electropedia.org/
— ISO Online browsing platform: available at https://www.iso.org/obp
3.1
access card
card or tag, read only or read write, without integrated circuit, does not provide encryption
Note 1 to entry: Can be used with contact or contactless.
EXAMPLE magnetic stripe, barcode
3.2
actuator
electrically operated means to affect or enable operation of the MDF “at rest” position unforced condition
of the lever handle or knob
3.3
attack
unauthorized attempt to operate a MDF by various techniques (destructive and or non-destructive
techniques)
3.4
audit trail
functionality intended to provide a record of MDF and/or its credential events that will identify the
individual credential used to operate the MDF
3.5
backplate
element whose purpose is, firstly, functional, providing a bearing for the rotation of a lever handle or
knob and the means of attachment to the door; and, secondly, decorative, working as a trim plate to cover
holes provided in the door for the passage of spindles, keys or lock cylinders
3.6
coupled
status of the actuator when the bolt and/or latch bolt can be operated by the handle, knob/thumb turn
or electrically
3.7
credential
identification means containing information necessary to authorize operation of the MDF
3.8
cylinder
device, usually distinct from its associated lock or latch, operated by a key, knob or thumb turn
7
---------------------- Page: 9 ----------------------
SIST EN 16867:2020+A1:2022
EN 16867:2020+A1:2021 (E)
3.9
door furniture
combination of lever handles or knobs on backplates or roses for the purpose of operating latches or
locks
3.10
escutcheon
surround with a shaped hole to accommodate a key or a lock cylinder, with or without a pivoted cover
plate, intended primarily to protect the door leaf from abrasion caused by keys
3.11
external plate
backplate or rose that is fitted on the external face of a door
3.12
False Acceptance Rate
FAR
probability that the system incorrectly authorizes a non-authorized person, due to incorrectly matching
the biometric input with a template
Note 1 to entry: The FAR is normally expressed as a percentage, following the FAR definition this is the percentage
of invalid inputs which are incorrectly accepted.
3.13
FAR-1
1/FAR
inverse of FAR
3.14
half set
single lever or knob attached to a plate or rose which enables operation of the lock or latch from one side
of the door only
3.15
Integrated Circuit Card
ICC
card, tag or device with an integrated circuit
Note 1 to entry: Can be used with contact or contactless (RFID), active or passive.
EXAMPLE RFID, Smartcard.
3.16
inside
side of the door that is facing the controlled area
3.17
internal plate
backplate or rose that is fitted on the internal face of a door
3.18
knob
element for mechanical hand operation of the MDF
8
---------------------- Page: 10 ----------------------
SIST EN 16867:2020+A1:2022
EN 16867:2020+A1:2021 (E)
3.19
latchplate
backplate adapted for use with a latch and having no keyhole or cylinder aperture
3.20
lever handle
rotatable operating element designed as a lever with a length from its axis of rotation to its free end that
exceeds 75 mm
3.21
manufacturer
natural or legal person who manufactures a construction product or who has such a product designed or
manufactured, or markets that product under his name or trademark and putting the product on the
market
3.22
mechatronic door furniture
MDF
combination of lever handles or knobs on backplates or roses with an integrated or a remote electronic
system, which is to be used with a mechanical or electromechanical lock for the purpose of operating the
lock after verifying the authorization of a credential
3.22.1
mechatronic door furniture
MDF Type A
handle or knob operated door furniture with electrically operated actuator, reading unit for credential
and power supply to be combined with a mechanically-operated lock
Note 1 to entry: The mechanically-operated lock shall meet EN 12209 or EN 15685.
3.22.2
mechatronic door furniture
MDF Type B
handle or knob operated door furniture with reading unit for credential and power supply to be combined
with electrically-operated locks
Note 1 to entry: The electrically-operated lock shall meet EN 14846.
3.23
No Performance Determined
NPD
no requirement and no test required
3.24
outside
side of the door that is facing the uncontrolled area
3.25
rose
element generally circular, but which may have equi-axial or approximately equi-axial shapes such as
square or octagonal, that otherwise has the same features as a backplate
9
---------------------- Page: 11 ----------------------
SIST EN 16867:2020+A1:2022
EN 16867:2020+A1:2021 (E)
3.26
security furniture
device which provides added resistance to the lock and/or cylinder against physical attack
3.27
spindle
bar, usually square in cross-section, that engages with a follower
3.28
spring-assisted handle/ knob
MDF lever handle or knob furniture that incorporates a spring which assists the return of the handle or
knob to its intended “at-rest” position
3.29
spring-loaded handle/ knob
MDF lever handle or knob that incorporates a spring which returns of the handle or knob to its intended
“at-rest” position without any assistance from the lock
3.30
tester
person who performs the test
3.31
time zone
degree of functionality intended to provide security or convenience by limiting the time that a valid
credential will operate the mechatronic door furniture
3.32
thumb turn
element of the MDF for mechanical finger operation
3.33
uncoupled
status of the actuator when neither bolt or latch bolt can be operated by the handle, knob/ thumb turn or
electrically
3.34
unsprung handle/ knob
MDF handle or knob not fitted with a spring in the backplate or rose
4 Requirements
4.1 General
4.1.1 Classification principle
The structure of the following requirements and test procedures reflects the classification in accordance
with Clause 7.
It is up to the tester together with the manufacturer to decide which requirements and test methods are
relevant to the technical design.
10
---------------------- Page: 12 ----------------------
SIST EN 16867:2020+A1:2022
EN 16867:2020+A1:2021 (E)
4.1.2 Compatibility between cooperating parts
The manufacturer shall state which cooperating parts have been designed to be used in combination. For
compatibility and functionality between cooperating parts (products) similar classification necessary.
Verified by 6.1.2.
4.1.3 Dangerous substances
National regulations on dangerous substances may require verification and declaration on release, and
sometimes content, when construction products covered by this document are placed on those markets.
In the absence of European harmonized test methods, verification and declaration on release/content
should be done taking into account national provisions in the place of use.
NOTE An informative database covering European and national provisions on dangerous substances is
available at the Construction website on EUROPA accessed through https://ec.europa.eu/growth/tools-
databases/cp-ds_en.
Verified by 6.1.3.
4.1.4 Operation time for change of status
Operation time for a change of status between uncoupled and coupled status or vice versa shall not
exceed 3 s. Verified by 6.1.4.
4.1.5 Product information requirements
Products classified in accordance with this document shall have clear and detailed instructions for their
installation and maintenance. These instructions shall at least contain:
a) the limitation of the products intended use, the limitation of the door mass and door dimensions,
temperature range and the field of door application and centre distance between axes where
applicable;
b) the spindle and fastening elements shall be specified by the manufacturer. The manufacturer should
state clearly the door thickness or range of door thicknesses for which the furniture is suitable, and
in the case of spring-assisted and spring-loaded furniture, the angle of rotation possible by the
design;
c) information to ensure that the product can conform to the performance requirements of this
document, including known restriction of use, for example conditions under which the product could
be rendered inoperable;
d) an extended temperature range if applicable;
e) information about suitability for use on fire resistance and/or smoke control door set if applicable;
f) information of the risk of misuse, dangerous substances and explosion of heated parts;
g) if applicable information of IP classification according to EN 60529, for outside and/or inside;
h) the information of any override function if applicable (i.e. mechanical cylinder);
11
---------------------- Page: 13 ----------------------
SIST EN 16867:2020+A1:2022
EN 16867:2020+A1:2021 (E)
i) Optional information about the following product features:
1) time zone possibilities (like number of time profiles, special time functions);
2) the quality of time zones (for example recurring (daily, weekly or calendar);
3) authorization process for an access modification (code, master code);
4) audit trails: quantity, with or without time-stamp, authorized access, denied access also, access
programming;
5) effect on the coupled and uncoupled status during and after the removal of main power;
6) battery change: duration of no data loss;
7) battery low or main power failure, deeper than the minimum of working voltage;
8) external power supply in case of main power failure (if applicable);
9) duration of storage of the audit trails;
10) max number of operation with new battery and theoretical operable time for the MDF in years
without operation with new battery (battery recommended by the manufacturer) and mean
stand-by power consumption in watt;
11) for devices with external power supply:
— allowable voltage range;
— maximum current in A;
— max. power consumption in operation in A/voltage;
— typical standby consumption in watt.
4.2 Category of use (1st character)
4.2.1 General
The grading 1 and 2 for category of use gives the performance aimed for product to the residential market
and grades 3 and 4 focus more on commercial building application see also 7.2.
When the MDF is fitted to the door there shall be no sharp edges.
NOTE This requirement would typically be satisfied by edges that are broken by a chamfer of 0,5 mm
maximum × 45° or by a radius of 0,5 mm minimum.
In the area of rotation of the lever handle or knob, the head of any visible fastening element shall be level
with or below the surface of the backplate or rose after fitting. However, raised head screws may stand
proud of the furniture plate by the domed height of the screw head.
Any fastening element that secures the lever handle or knob to the spindle shall not project above the
surface by more than 1 mm after fitting.
The design of MDF shall ensure that, after fitting, it is not possible for the fingers of a user to be trapped
between lever handle or knob and backplate or rose over the full range of rotation of the lever handle or
knob.
Verify according to 6.2.1.
12
---------------------- Page: 14 ----------------------
SIST EN 16867:2020+A1:2022
EN 16867:2020+A1:2021 (E)
4.2.2 Axial strength of MDF and fixing
The MDF shall resist an axial force F1 indicated in Table 1 for the different grades without breaking any
component.
The MDF shall be operable and have a maximum permanent deformation δ1 indicated in Table 1 at the
reference point after de-loaded the force.
The test shall be done in accordance with 6.2.2.
4.2.3 Requirement for free play
The maximum total movement of all knobs, thumb turns or lever handles mechanically connected to the
MDF shall not exceed the value specified in Table 1.
See Figure 2. (6.2.3)
The test shall be done in accordance with 6.2.3.
4.2.4 Free angular movement or misalignment
Where applicable the free angular movement or misalignment of the MDF shall not exceed the value
specified in Table 1.
The test shall be done in accordance with 6.2.4.
4.2.5 Operating torque
4.2.5.1 Unsprung and spring assisted lever handles
The torque M1 required to return the unsprung or spring assisted lever handle back to its intended “at-
rest” position shall be not greater than the value specified in Table 1.
After the durability test the spring-assisted lever handles only, the torque M2 required to rotate the lever
handle to a minimum angle of 40° from its intended “at-rest” position shall not exceed the value specified
in Table 1.
The test shall be done in accordance with 6.2.5.1.
4.2.5.2 Unsprung knobs
The return torque M3 value for unsprung knobs shall in either direction not be greater than the value
specified in Table 1.
The test shall be done in accordance with 6.2.5.2.
4.2.5.3 Spring loaded lever handles or knobs
For spring loaded handles, knobs or thumb turns, the torque M4 required to rotate the lever handles,
knobs or thumb turn through an angle α of 60° 0°/+5° or through the angle of rotation possible by the
design shall not be more the value specified in Table 1.
After the durability test and after removal of the torque, the lever handle or knob shall return to its
recorded “at-rest” position within angle φ according to the value specified in Table 1.
The test shall be done in accordance with 6.2.5.3.
13
---------------------- Page: 15 ----------------------
SIST EN 16867:2020+A1:2022
EN 16867:2020+A1:2021 (E)
4.2.6 Rotational torque strength
The MDF shall resist rotational torque M5 specified in Table 1 and shall show no failure of any component
and the lever handles or knobs shall still be operational after the test.
Lever handles or knobs shall not deform permanently more than a distance δ4 according to Table 1 as
measured at the reference point after de-loaded the torque.
The test shall be done in accordance with 6.2.6.
4.2.7 Minimum lever or knob torque transfer
4.2.7.1 Minimum lever torque transfer
The MDF shall be able to transfer the torque specified in Table 1.
If a MDF is equipped with a lever on the outside and this MDF is protected by a mean to prevent damage
in case of excessive torque M6 is applied to the lever, the mean shall be able to transfer a minimum torque
as specified in Table 1.
Compliance is checked by the test methods given in 6.2.7.
4.2.7.2 Minimum
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.