SIST EN 14617-12:2012

Agglomerated stone - Test methods - Part 12: Determination of dimensional stability

This European Standard specifies the test method to be used for the determination of the dimensional stability and warping of agglomerated stones when in contact with water.
This European Standard applies to agglomerated stones to be installed by adhesive on walls and floors.
The test is mainly performed to classify the material according to the degree of sensitivity to water and to select a suitable adhesive for the correct laying of agglomerated stones.

Künstlich hergestellter Stein - Prüfverfahren - Teil 12: Bestimmung der Maßhaltigkeit

Diese Europäische Norm legt das zur Bestimmung von Maßhaltigkeit und Verwölbung (Werfen) von künstlich hergestellten Steinen anzuwendende Prüfverfahren fest, wenn diese mit Wasser in Kontakt kommen.
Diese Europäische Norm gilt für künstlich hergestellte Steine, die mit Klebstoff an Wänden und auf Fußböden zu verlegen sind.
Die Prüfung wird hauptsächlich vorgenommen, um das Material entsprechend dem Grad der Empfindlichkeit gegenüber Wasser zu klassifizieren und um einen geeigneten Klebstoff für die Verlegung der künstlich hergestellten Steine auszuwählen.

Pierre agglomérée - Méthodes d'essai - Partie 12: Détermination de la stabilité dimensionnelle

La présente Norme européenne spécifie une méthode d’essai à utiliser pour déterminer la stabilité
dimensionnelle et le gauchissement de pierres agglomérées lorsqu’elles sont en contact avec l’eau.
La présente Norme européenne s’applique aux pierres agglomérées devant être collées sur les murs et les
sols.
L’essai est principalement réalisé pour classer le matériau en fonction de son degré de sensibilité à l’eau et
pour sélectionner un adhésif approprié pour une pose correcte des pierres agglomérées.

Aglomeriran kamen - Preskusne metode - 12. del: Ugotavljanje dimenzijske stabilnosti

Ta evropski standard določa preskusno metodo za ugotavljanje dimenzijske stabilnosti in zvijanja aglomeriranega kamna ob stiku z vodo. Ta evropski standard se uporablja za aglomerirani kamen, namenjen za lepljenje na zidove in tla. Namen preskusa je razvrstiti material glede na stopnjo občutljivosti na vodo in izbrati ustrezno lepilo za pravilno polaganje aglomeriranega kamna.

General Information

• Status: Published
• Publication Date: 10-Jun-2012
• ICS: 91.100.15 - Mineral materials and products
• Technical Committee: IKER - Ceramics
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 01-Jun-2012
• Due Date: 06-Aug-2012
• Completion Date: 11-Jun-2012
• Ref Project: EN 14617-12:2012 - Agglomerated stone - Test methods - Part 12: Determination of dimensional stability

Relations

• Replaces: SIST EN 14617-12:2005 - Agglomerated stone - Test methods - Part 12: Determination of dimensional stability
• Effective Date: 01-Jul-2012

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Aglomeriran kamen - Preskusne metode - 12. del: Ugotavljanje dimenzijske stabilnostiKünstlich hergestellter Stein - Prüfverfahren - Teil 12: Bestimmung der MaßhaltigkeitPierre agglomérée - Méthodes d'essai - Partie 12: Détermination de la stabilité dimensionnelleAgglomerated stone - Test methods - Part 12: Determination of dimensional stability91.100.15Mineralni materiali in izdelkiMineral materials and productsICS:Ta slovenski standard je istoveten z:EN 14617-12:2012SIST EN 14617-12:2012en,fr,de01-julij-2012SIST EN 14617-12:2012SLOVENSKI
STANDARDSIST EN 14617-12:20051DGRPHãþD



SIST EN 14617-12:2012



EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 14617-12
April 2012 ICS 91.100.15 Supersedes EN 14617-12:2005English Version
Agglomerated stone - Test methods - Part 12: Determination of dimensional stability
Pierre agglomérée - Méthodes d'essai - Partie 12: Détermination de la stabilité dimensionnelle
Künstlich hergestellter Stein - Prüfverfahren - Teil 12: Bestimmung der Maßhaltigkeit This European Standard was approved by CEN on 9 March 2012.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2012 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 14617-12:2012: ESIST EN 14617-12:2012



EN 14617-12:2012 (E) 2 Contents Page Foreword .31 Scope .52 Normative references .53 Principle .54 Apparatus .55 Test conditions .66 Test specimens .67 Test procedure .78 Expression of results .79 Test report .8Annex A (normative)
Test method for tiles below 12 mm .9Annex B (informative)
Choice of the adhesive . 10Bibliography . 12 SIST EN 14617-12:2012



EN 14617-12:2012 (E) 3 Foreword This document (EN 14617-12:2012) has been prepared by Technical Committee CEN/TC 246 “Natural stones”, the secretariat of which is held by UNI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by October 2012, and conflicting national standards shall be withdrawn at the latest by October 2012. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 14617-12:2005. Clauses 1 and 3, 4.1, 4.2, 4.3, 4.4 and Clauses 5 to 8 have been modified since the last edition of this European Standard. A new Annex A (normative) has been added, the Annex B (informative) has been modified since the last edition (Annex A) and 4.5 has been deleted. This European Standard is one of a series of standards for test methods for agglomerated stones which includes the following: EN 14617-1, Agglomerated stone — Test methods — Part 1: Determination of apparent density and water absorption EN 14617-2, Agglomerated stone — Test methods — Part 2: Determination of flexural strength (bending) EN 14617-4, Agglomerated stone — Test methods — Part 4: Determination of the abrasion resistance
EN 14617-5, Agglomerated stone — Test methods — Part 5: Determination of freeze and thaw resistance EN 14617-6, Agglomerated stone — Test methods — Part 6: Determination of thermal shock resistance EN 14617-8, Agglomerated stone — Test methods — Part 8: Determination of resistance to fixing (dowel hole) EN 14617-9, Agglomerated stone — Test methods — Part 9: Determination of impact resistance EN 14617-10, Agglomerated stone — Test methods — Part 10: Determination of chemical resistance EN 14617-11, Agglomerated stone — Test methods — Part 11: Determination of linear thermal expansion coefficient EN 14617-12, Agglomerated stone — Test methods — Part 12: Determination of dimensional stability EN 14617-13, Agglomerated stone — Test methods — Part 13: Determination of electrical resistivity EN 14617-15, Agglomerated stone — Test methods — Part 15: Determination of compressive strength EN 14617-16, Agglomerated stone — Test methods — Part 16: Determination of dimensions, geometric characteristics and surface quality of modular tiles According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, SIST EN 14617-12:2012



EN 14617-12:2012 (E) 4 Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
SIST EN 14617-12:2012



EN 14617-12:2012 (E) 5 1 Scope This European Standard specifies the test method to be used for the determination of the dimensional stability and warping of agglomerated stones w
...