SIST EN ISO 8747:2001

Grooved pins with countersunk head (ISO 8747:1997)

Senkkerbnägel (ISO 8747:1997)

Diese Internationale Norm beschreibt die Eigenschaften von Senkkerbnägeln, mit drei gleichmäßig verteilten Längskerben auf der Außenfläche. Die Kerbnägelhaben einen Nenndurchmesser d1 von 1,4 mm bis einschließlich 20 mm. Der zu jeder Seite der Kerbe verdrängte Werkstoff, der den aufgeweiterten Durchmesser d2 bildet, welcher größer als der Nenndurchmesser d1 ist, führt zu einer kraftschlüssigen Verbindung, wenn diese Kerbnägel in eine Bohrung mit einem Durchmesser gleich dem Nenndurchmesser d1 (siehe Abschnitt 4) gepreßt werden.

Clous cannelés a tete fraisée (ISO 8747:1997)

La présente Norme internationale prescrit les caractéristiques des clous cannelés à tête fraisée, à trois cannelures constantes sur toute leur longueur, débouchantes d'un côté et régulièrement espacées, de diamètre nominal, d1, de 1,4 mm à 20 mm inclus. Le matériau refoulé de chaque côté des cannelures forme un renflement dont le diamètre d2, supérieur au diamètre nominal d1, permet un ajustement serré de ces clous cannelés lorsqu'ils sont emmanchés en force dans un trou de diamètre de perçage égal au diamètre nominal du clou d1 (voir article 4).

Zasekani zatiči z ugrezno glavo in brazdami enake globine po vsej dolžini (ISO 8747:1997)

General Information

• Status: Published
• Publication Date: 30-Jun-2001
• ICS: 21.060.50 - Pins, nails
• Technical Committee: ISEL - Mechanical elements
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 01-Jul-2001
• Due Date: 01-Jul-2001
• Completion Date: 01-Jul-2001
• Ref Project: EN ISO 8747:1997 - Grooved pins with countersunk head (ISO 8747:1997)

Relations

• Replaces: SIST EN 28747:1996 - Grooved pins with countersunk head (ISO 8747:1986)
• Effective Date: 01-Jul-2001

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 8747:2001
01-julij-2001
1DGRPHãþD
SIST EN 28747:1996
=DVHNDQL]DWLþL]XJUH]QRJODYRLQEUD]GDPLHQDNHJORELQHSRYVHMGROåLQL,62

Grooved pins with countersunk head (ISO 8747:1997)
Senkkerbnägel (ISO 8747:1997)
Clous cannelés a tete fraisée (ISO 8747:1997)
Ta slovenski standard je istoveten z: EN ISO 8747:1997
ICS:
21.060.50 =DWLþLåHEOML Pins, nails
SIST EN ISO 8747:2001 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 8747:2001

---------------------- Page: 2 ----------------------

SIST EN ISO 8747:2001

---------------------- Page: 3 ----------------------

SIST EN ISO 8747:2001

---------------------- Page: 4 ----------------------

SIST EN ISO 8747:2001
INTERNATIONAL ISO
STANDARD 8747
Second edition
1997-11-15
Grooved pins with countersunk head
Clous cannelés à tête fraisée
A
Reference number
ISO 8747:1997(E)

---------------------- Page: 5 ----------------------

SIST EN ISO 8747:2001
ISO 8747:1997(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide
federation of national standards bodies (ISO member bodies). The work of
preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which
a technical committee has been established has the right to be represented
on that committee. International organizations, governmental and non-
governmental, in liaison with ISO, also take part in the work. ISO
collaborates closely with the International Electrotechnical Commission
(IEC) on all matters of electrotechnical standardization.
Draft International Standards adopted by the technical committees are
circulated to the member bodies for voting. Publication as an International
Standard requires approval by at least 75 % of the member bodies casting
a vote.
International Standard ISO 8747 was prepared by Technical Committee
ISO/TC 2, Fasteners.
This second edition cancels and replaces the first edition (ISO 8747:1986),
which has been technically revised.
©  ISO 1997
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced
or utilized in any form or by any means, electronic or mechanical, including photocopying and
microfilm, without permission in writing from the publisher.
International Organization for Standardization
Case postale 56 • CH-1211 Genève 20 • Switzerland
Internet [e-mail]
X.400 c=ch; a=400net; p=iso; o=isocs; s=central
Printed in Switzerland
ii

---------------------- Page: 6 ----------------------

SIST EN ISO 8747:2001
©
INTERNATIONAL STANDARD  ISO ISO 8747:1997(E)
Grooved pins with countersunk head
1 Scope
This International Standard specifies the characteristics of countersunk head grooved pins which have three
equally spaced grooves impressed longitudinally on their exterior surface, with nominal diameter, d , from
1
1,4 mm to 20 mm inclusive.
The displaced material to each side of the grooves forming an expanded diameter, d , which is larger than the
2
nominal diameter, d , will cause a non-positive locking fit when these grooved pins are forced into a drilled
1
hole equal to the nominal diameter d (see clause 4).
1
2 Normative references
The following standards contain provisions which, through reference in this text, constitute provisions of this
International Standard. At the time of publication, the editions indicated were valid. All standards are subject
to revision, and parties to agreements based on this International Standard are encouraged to investigate the
possibility of applying the
...