SIST EN ISO 4017:2011
(Main)Hexagon head screws - Product grades A and B (ISO 4017:2011)
Hexagon head screws - Product grades A and B (ISO 4017:2011)
This International Standard specifies the characteristics of hexagon head screws with threads from M1,6 up to and including M64, of product grade A for threads M1,6 to M24 and nominal lengths up to and including 10d or 150 mm, whichever is the shorter, and product grade B for threads over M24 or nominal lengths over 10d or 150 mm, whichever is the shorter.
NOTE This type of product is the same as that covered by ISO 4014 with the exception of threading up to head and nominal lengths up to and including 200 mm as preferred lengths.
If, in special cases, specifications other than those listed in this International Standard are required, they can be selected from existing International Standards, for example ISO 724, ISO 888, ISO 898-1, ISO 965-1, ISO 3506-1, ISO 4753 and ISO 4759-1.
Sechskantschrauben mit Gewinde bis Kopf - Produktklassen A und B (ISO 4017:2011)
Diese Internationale Norm legt Eigenschaften von Sechskantschrauben mit Gewinde bis Kopf und Gewinden
von M 1,6 bis M 64, mit Produktklasse A für Gewinde von M 1,6 bis M 24 und Nennlängen ≤ 10 d oder
≤ 150 mm, wobei der kleinere Zahlenwert gilt, und mit Produktklasse B für Gewinde über M 24 oder
Nennlängen > 10 d oder > 150 mm, wobei der kleinere Zahlenwert gilt, fest.
ANMERKUNG Diese Sechskantschrauben entsprechen denen nach ISO 4014. Sie haben lediglich Gewinde bis Kopf
und sind handelsüblich nur in Nennlängen bis 200 mm festgelegt.
Falls in besonderen Fällen andere Festlegungen als die in dieser Norm aufgeführten benötigt werden, können
diese den entsprechenden ISO-Normen entnommen werden, z. B. ISO 724, ISO 888, ISO 898-1, ISO 965-1,
ISO 3506-1, ISO 4753 und ISO 4759-1.
Vis à tête hexagonale entièrement filetées - Grades A et B (ISO 4017:2011)
L'ISO 4017:2010 sp�cifie les caract�ristiques des vis � t�te hexagonale enti�rement filet�es de filetage M1,6 � M64 inclus, de grade A pour les filetages M1,6 � M24 inclus et les longueurs nominales inf�rieures ou �gales � 10d ou � 150 mm, la plus petite des deux valeurs �tant retenue, et de grade B pour les filetages sup�rieurs � M24 ou les longueurs nominales sup�rieures � 10d ou � 150 mm, la plus petite des deux valeurs �tant retenue.
Vijaki s šestrobo glavo z navojem do glave - Razreda izdelave A in B (ISO 4017:2011)
Ta mednarodni standard določa značilnosti vijakov s šestrobo glavo z navojem do glave od M1,6 do vključno M64 razreda izdelave A za navoje od M1,6 do M24 in z nazivnimi dolžinami do vključno 10d ali 150 mm, odvisno od tega, kaj je krajše, in razreda izdelave B za navoje nad M24 oziroma z nazivnimi dolžinami nad 10d ali 150 mm, odvisno od tega, kaj je krajše.
OPOMBA: Ta tip proizvoda je enak kot tip, zajet z ISO 4014, razen navoja do glave in nominalnih dolžin do in vključno 200 mm kot prednostnih dolžin.
Če se v posebnih primerih zahtevajo specifikacije, ki so drugačne od navedenih v tem mednarodnem standardu, se lahko izberejo med obstoječimi mednarodnimi standardi, na primer ISO 724, ISO 888, ISO 898-1, ISO 965-1, ISO 3506-1, ISO 4753 in ISO 4759-1.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 4017:2011
01-oktober-2011
1DGRPHãþD
SIST EN ISO 4017:2002
Vijaki s šestrobo glavo z navojem do glave - Razreda izdelave A in B (ISO
4017:2011)
Hexagon head screws - Product grades A and B (ISO 4017:2011)
Sechskantschrauben mit Gewinde bis Kopf - Produktklassen A und B (ISO 4017:2011)
Vis à tête hexagonale entièrement filetées - Grades A et B (ISO 4017:2011)
Ta slovenski standard je istoveten z: EN ISO 4017:2011
ICS:
21.060.10 Sorniki, vijaki, stebelni vijaki Bolts, screws, studs
SIST EN ISO 4017:2011 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 4017:2011
---------------------- Page: 2 ----------------------
SIST EN ISO 4017:2011
EUROPEAN STANDARD
EN ISO 4017
NORME EUROPÉENNE
EUROPÄISCHE NORM
April 2011
ICS 21.060.10 Supersedes EN ISO 4017:2000
English Version
Hexagon head screws - Product grades A and B (ISO
4017:2011)
Vis à tête hexagonale entièrement filetées - Grades A et B Sechskantschrauben mit Gewinde bis Kopf -
(ISO 4017:2011) Produktklassen A und B (ISO 4017:2011)
This European Standard was approved by CEN on 31 January 2011.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2011 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 4017:2011: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 4017:2011
EN ISO 4017:2011 (E)
Contents Page
Foreword .3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 4017:2011
EN ISO 4017:2011 (E)
Foreword
This document (EN ISO 4017:2011) has been prepared by Technical Committee ISO/TC 2 "Fasteners" in
collaboration with Technical Committee CEN/TC 185 "Fasteners", the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by October 2011, and conflicting national standards shall be withdrawn at
the latest by October 2011.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 4017:2000.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of ISO 4017:2011 has been approved by CEN as a EN ISO 4017:2011 without any modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 4017:2011
---------------------- Page: 6 ----------------------
SIST EN ISO 4017:2011
INTERNATIONAL ISO
STANDARD 4017
Fourth edition
2011-04-01
Hexagon head screws — Product grades
A and B
Vis à tête hexagonale entièrement filetées — Grades A et B
Reference number
ISO 4017:2011(E)
©
ISO 2011
---------------------- Page: 7 ----------------------
SIST EN ISO 4017:2011
ISO 4017:2011(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2011
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2011 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 4017:2011
ISO 4017:2011(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 4017 was prepared by Technical Committee ISO/TC 2, Fasteners, Subcommittee SC 10, Product
standards for fasteners.
This fourth edition cancels and replaces the third edition (ISO 4017:1999), of which it constitutes a minor
revision.
© ISO 2011 – All rights reserved iii
---------------------- Page: 9 ----------------------
SIST EN ISO 4017:2011
ISO 4017:2011(E)
Introduction
This International Standard belongs to a complete family of product standards developed by ISO on external
hexagon drive fasteners. It comprises the following:
a) hexagon head bolts (ISO 4014, ISO 4015, ISO 4016 and ISO 8765);
b) hexagon head screws (ISO 4017, ISO 4018 and ISO 8676);
c) hexagon nuts (ISO 4032, ISO 4033, ISO 4034, ISO 4035, ISO 4036, ISO 7040, ISO 7041, ISO 7042,
ISO 7719, ISO 7720, ISO 8673, ISO 8674, ISO 8675, ISO 10511, ISO 10512 and ISO 10513);
d) hexagon bolts with flange (ISO 4162, ISO 15071 and ISO 15072);
e) hexagon nuts with flange (ISO 4161, ISO 7043, ISO 7044, ISO 10663, ISO 12125, ISO 12126 and
ISO 21670).
iv © ISO 2011 – All rights reserved
---------------------- Page: 10 ----------------------
SIST EN ISO 4017:2011
INTERNATIONAL STANDARD ISO 4017:2011(E)
Hexagon head screws — Product grades A and B
1 Scope
This International Standard specifies the characteristics of hexagon head screws with threads from M1,6 up to
and including M64, of product grade A for threads M1,6 to M24 and nominal lengths up to and including 10d or
150 mm, whichever is the shorter, and product grade B for threads over M24 or nominal lengths over 10d or
150 mm, whichever is the shorter.
NOTE This type of product is the same as that covered by ISO 4014 with the exception of threading up to head and
nominal lengths up to and including 200 mm as preferred lengths.
If, in special cases, specifications other than those listed in this International Standard are required, they can
be selected from existing International Standards, for example ISO 724, ISO 888, ISO 898-1, ISO 965-1,
ISO 3506-1, ISO 4753 and ISO 4759-1.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 225, Fasteners — Bolts, screws, studs and nuts — Symbols and descriptions of dimensions
ISO 724, ISO general-purpose metric screw threads — Basic dimensions
ISO 898-1, Mechanical properties of fasteners made of carbon steel and alloy steel — Part 1: Bolts, screws
and studs with specified property classes — Coarse thread and fine pitch thread
ISO 965-1, ISO general-purpose metric screw threads — Tolerances — Part 1: Principles and basic data
ISO 3269, Fasteners — Acceptance inspection
ISO 3506-1, Mechanical properties of corrosion-resistant stainless steel fasteners — Part 1: Bolts, screws and
studs
ISO 3508, Thread run-outs for fasteners with thread in accordance with ISO 261 and ISO 262
ISO 4042, Fasteners — Electroplated coatings
ISO 4753, Fasteners — Ends of parts with external ISO metric thread
ISO 4759-1, Tolerances for fasteners — Part 1: Bolts, screws, studs and nuts — Product grades A, B and C
ISO 6157-1, Fasteners — Surface discontinuities — Part 1: Bolts, screws and studs for general requirements
ISO 8839, Mechanical properties of fasteners — Bolts, screws, studs and nuts made of non-ferrous metals
ISO 8992, Fasteners — General requirements for bolts, screws, studs and nuts
ISO 10683, Fasteners — Non-electrolytically applied zinc flake coatings
© ISO 2011 – All rights reserved 1
---------------------- Page: 11 ----------------------
SIST EN ISO 4017:2011
ISO 4017:2011(E)
3 Dimensions
See Figure 1 and Tables 1 and 2.
Symbols and descriptions of dimensions are specified in ISO 225.
Dimensions in millimetres
a
β = 15° to 30°.
b
Point shall be chamfered or for threads u M4 may be as-rolled (sheared end) in accordance with ISO 4753.
c
Incomplete thread u u 2P.
d
Reference datum for d .
w
e
d ≈ pitch diameter.
s
f
Permissible shape.
Figure 1
2 © ISO 2011 – All rights reserved
---------------------- Page: 12 ----------------------
SIST EN ISO 4017:2011
ISO 4017:2011(E)
Table 1 — Preferred threads
Dimensions in millimetres
Thread, d M1,6 M2 M2,5 M3 M4 M5 M6
a
P 0,35 0,4 0,45 0,5 0,7 0,8 1
b
max. 1,05 1,2 1,35 1,5 2,1 2,4 3
a
min. 0,35 0,4 0,45 0,5 0,7 0,8 1
max. 0,25 0,25 0,25 0,40 0,40 0,50 0,50
c
min. 0,10 0,10 0,10 0,15 0,15 0,15 0,15
d max. 2 2,6 3,1 3,6 4,7 5,7 6,8
a
A 2,27 3,07 4,07 4,57 5,88 6,88 8,88
d Product grade min.
w
B 2,30 2,95 3,95 4,45 5,74 6,74 8,74
A 3,41 4,32 5,45 6,01 7,66 8,79 11,05
e Product grade min.
B 3,28 4,18 5,31 5,88 7,50 8,63 10,89
nom. 1,1 1,4 1,7 2 2,8 3,5 4
max. 1,225 1,525 1,825 2,125 2,925 3,65 4,15
Product grade A
k
min. 0,975 1,275 1,575 1,875 2,675 3,35 3,85
max. 1,3 1,6 1,9 2,2 3,0 3,74 4,24
Product grade B
min. 0,9 1,2 1,5 1,8 2,6 3,26 3,76
c
k A 0,68 0,89 1,10 1,31 1,87 2,35 2,70
w
Product grade min.
B 0,63 0,84 1,05 1,26 1,82 2,28 2,63
r min. 0,1 0,1 0,1 0,1 0,2 0,2 0,25
nom. = max. 3,20 4,00 5,00 5,50 7,00 8,00 10,00
s A 3,02 3,82 4,82 5,32 6,78 7,78 9,78
Product grade min.
B 2,90 3,70 4,70 5,20 6,64 7,64 9,64
Product grade
A B
l
nom. min. max. min. max.
2 1,8 2,2 — —
3 2,8 3,2 — —
4 3,76 4,24 — —
5 4,76 5,24 — —
6 5,76 6,24 — —
8 7,71 8,29 — —
10 9,71 10,29 — —
12 11,65 12,35 — —
16 15,65 16,35 — —
20 19,58 20,42 18,95 21,05
25 24,58 25,42 23,95 26,05
30 29,58 30,42 28,95 31,05
35 34,5 35,5 33,75 36,25
40 39,5 40,5 38,75 41,25
45 44,5 45,5 43,75 46,25
50 49,5 50,5 48,75 51,25
55 54,4 55,6 53,5 56,5
60 59,4 60,6 58,5 61,5
65 64,4 65,6 63,5 66,5
70 69,4 70,6 68,5 71,5
80 79,4 80,6 78,5 81,5
90 89,3 90,7 88,25 91,75
100 99,3 100,7 98,25 101,75
110 109,3 110,7 108,25 111,75
120 119,3 120,7 118,25 121,75
130 129,2 130,8 128 132
140 139,2 140,8 138 142
150 149,2 150,8 148 152
160 — — 158 162
180 — — 178 182
200 — — 197,7 202,3
© ISO 2011 – All rights reserved 3
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.