SIST EN 300 433 V2.1.1:2016
(Main)Citizens' Band (CB) radio equipment - Harmonised Standard covering the essential requirements of article 3.2 of the Directive 2014/53/EU
Citizens' Band (CB) radio equipment - Harmonised Standard covering the essential requirements of article 3.2 of the Directive 2014/53/EU
The present document covers the technical requirements for transmitters and receivers used in stations of angle
modulated, Double Side Band (DSB) modulated and/or Single Side Band (SSB) modulated Citizens' Band (CB) radio
equipment operating in all or part of the frequency band 26,960 MHz to 27,410 MHz with a channel spacing of 10 kHz,
and intended for analogue speech and/or data transmission.
Citizens' Band radio equipment operation is in accordance with ECC Decision (11)03 on the harmonised use of
frequencies for Citizens' Band (CB) radio equipment [i.2].
Any equipment using national regulations on Citizens' Band (CB) permitting the use of channels outside of the carrier
frequencies shown in table 1 within the frequency range from 26 MHz to 28 MHz can use the present document.
The types of equipment covered by the present document are as follows:
- Base station: equipment fitted with antenna connector.
- Mobile station: equipment fitted with antenna connector.
- Hand portable stations:
a) either fitted with an antenna connector; or
b) without an external antenna connector but fitted with a permanent internal or a temporary internal 50 Ω
RF connector which allows access to the transmitter output and the receiver input.
Hand portable station equipment without an external or internal Radio Frequency (RF) connector and without the possibility
of having a temporary internal 50 Ω RF connector is not covered by the present document (integral antenna equipment).
The present document contains requirements to demonstrate that "... Radio equipment shall be so constructed that it both
effectively uses and supports the efficient use of radio spectrum in order to avoid harmful interference" and that "....radio
equipment supports certain features ensuring access to emergency services".
In addition to the present document, other ENs that specify technical requirements in respect of essential requirements
under other parts of article 3 of the Radio Equipment Directive [i.4] may apply to equipment within the scope of the
present document.
Radijska oprema CB - Harmonizirani standard, ki zajema bistvene zahteve člena 3.2 direktive 2014/53/EU
Ta dokument zajema tehnične zahteve za oddajnike in sprejemnike, ki se uporabljajo v postajah radijske opreme CB s kotno modulacijo, dvobočnim (DSB) in/ali enobočnim (SSB) prenosom, ki deluje v celotnem frekvenčnem pasu ali v delu frekvenčnega pasu od 26,960 do 27,410 MHz z razmikom 10 kHz med kanali
ter je namenjena za analogni govor in/ali prenos podatkov.
Delovanje radijske opreme CB je v skladu s Sklepom Odbora za elektronske komunikacije (11)03 o usklajeni uporabi frekvenc za radijsko opremo CB [i.2].
Ta dokument se lahko uporablja za katero koli opremo, ki upošteva nacionalne predpise o CB, ki dovoljujejo uporabo kanalov zunaj frekvenc nosilcev, navedenih v tabeli 1, v frekvenčnem območju od 26 do 28 MHz.
Ta dokument zajema naslednje vrste opreme:
– bazno postajo (oprema z antenskim priključkom);
– mobilno postajo (oprema z antenskim priključkom);
– prenosne postaje:
a) z antenskim priključkom; ali
b) brez zunanjega antenskega priključka, vendar s stalnim ali začasnim notranjim 50-ohmskim
radijsko frekvenčnim (RF) priključkom, ki omogoča dostop do izhoda oddajnika in vhoda sprejemnika.
Ta dokument ne zajema prenosne opreme brez zunanjega ali notranjega radijsko frekvenčnega priključka in brez možnosti namestitve začasnega notranjega 50-ohmskega priključka (vgrajene antene).
Ta dokument vsebuje zahteve, s katerimi se dokazuje, da »... je radijska oprema sestavljena tako, da učinkovito uporablja in tudi podpira učinkovito uporabo radijskega spektra, tako da ne pride do škodljivih motenj«, ter da »... radijska oprema podpira določene funkcije, ki zagotavljajo dostop do storitev za nujne primere«.
Poleg tega dokumenta se za opremo na področju uporabe tega dokumenta uporabljajo tudi drugi standardi EN, ki določajo tehnične zahteve v zvezi z bistvenimi zahtevami iz drugih delov 3. člena direktive o radijski opremi [i.4].
General Information
Buy Standard
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 300 433 V2.1.1:2016
01-julij-2016
5DGLMVNDRSUHPD&%+DUPRQL]LUDQLVWDQGDUGNL]DMHPDELVWYHQH]DKWHYHþOHQD
GLUHNWLYH(8
Citizens' Band (CB) radio equipment - Harmonised Standard covering the essential
requirements of article 3.2 of the Directive 2014/53/EU
Ta slovenski standard je istoveten z: ETSI EN 300 433 V2.1.1 (2016-05)
ICS:
33.060.01 Radijske komunikacije na Radiocommunications in
splošno general
SIST EN 300 433 V2.1.1:2016 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 300 433 V2.1.1:2016
---------------------- Page: 2 ----------------------
SIST EN 300 433 V2.1.1:2016
ETSI EN 300 433 V2.1.1 (2016-05)
HARMONISED EUROPEAN STANDARD
Citizens' Band (CB) radio equipment;
Harmonised Standard covering the essential requirements
of article 3.2 of the Directive 2014/53/EU
---------------------- Page: 3 ----------------------
SIST EN 300 433 V2.1.1:2016
2 ETSI EN 300 433 V2.1.1 (2016-05)
Reference
REN/ERM-TGDMR-346
Keywords
CB, radio, testing
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2016.
All rights reserved.
TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.
TM
3GPP and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI
---------------------- Page: 4 ----------------------
SIST EN 300 433 V2.1.1:2016
3 ETSI EN 300 433 V2.1.1 (2016-05)
Contents
Intellectual Property Rights . 6
Foreword . 6
Modal verbs terminology . 6
1 Scope . 7
2 References . 7
2.1 Normative references . 7
2.2 Informative references . 8
3 Definitions, symbols and abbreviations . 8
3.1 Definitions . 8
3.2 Symbols . 9
3.3 Abbreviations . 9
4 General and operational requirements . 10
4.0 General . 10
4.1 Choice of model for testing . 10
4.1.0 General . 10
4.1.1 Auxiliary test equipment . 11
4.1.2 Declarations by the provider . 11
4.2 Testing of equipment that does not have an external 50 Ω RF connector (integral antenna equipment) . 11
4.3 Mechanical and electrical design . 11
4.3.1 General . 11
4.3.2 Controls . 11
4.3.3 PTT and voice- activated switch . 11
4.3.4 Combination with other equipment . 11
4.4 Operating frequencies . 12
4.5 Marking . 12
5 Test conditions, power sources and ambient temperatures . 12
5.0 Environmental profile . 12
5.1 Normal and extreme test conditions . 12
5.2 Test power source . 13
5.3 Normal test conditions . 13
5.3.1 Normal temperature and humidity . 13
5.3.2 Normal test power source . 13
5.3.2.1 Mains voltage . 13
5.3.2.2 Regulated lead-acid battery power sources used on vehicles . 13
5.3.2.3 Other power sources . 13
5.4 Extreme test conditions . 13
5.4.1 Extreme temperatures . 13
5.4.2 Extreme test power source . 14
5.4.2.1 Mains voltage . 14
5.4.2.2 Regulated lead-acid battery power sources used on vehicles . 14
5.4.2.3 Power sources using other types of batteries . 14
5.4.2.4 Other power sources . 14
5.5 Procedure for tests at extreme temperatures . 14
6 General test conditions . 14
6.1 Arrangements for test signals applied to the receiver input . 14
6.2 Receiver mute or squelch facility . 15
6.3 Receiver rated audio output power . 15
6.4 Transmitter rated RF power. 15
6.5 Normal test modulation . 15
6.5.1 DSB modulation . 15
6.5.2 SSB modulation . 15
6.5.3 Angle modulation (FM modulation with Preemphasis/Deemphasis) . 16
6.6 Artificial antenna . 16
6.7 Test fixture . 16
ETSI
---------------------- Page: 5 ----------------------
SIST EN 300 433 V2.1.1:2016
4 ETSI EN 300 433 V2.1.1 (2016-05)
6.8 Arrangement for test signals at the input of the transmitter . 16
6.9 Test site and general arrangements for radiated measurements. 16
7 Technical characteristics of the transmitter . 16
7.1 Frequency error . 16
7.1.0 Applicability . 16
7.1.1 Definition . 16
7.1.2 Method of measurement . 17
7.1.3 Limit . 17
7.2 Transmitter power . 17
7.2.1 Definition . 17
7.2.2 Method of measurement . 17
7.2.2.1 Method of measurement (conducted) . 17
7.2.2.2 Method of measurement (effective radiated power) . 17
7.2.3 Limits . 18
7.3 Maximum permissible frequency deviation . 18
7.3.0 Applicability . 18
7.3.1 Definition . 18
7.3.2 Method of measurement . 18
7.3.3 Limit . 19
7.4 Adjacent and alternate channel power . 19
7.4.1 Definition . 19
7.4.2 Method of measurement . 19
7.4.3 Limits . 20
7.5 Unwanted emissions in the spurious domain. 20
7.5.1 Definition . 20
7.5.2 Method of measurement . 21
7.5.2.1 Method of measuring the power level in a specified load (clause 7.5.1 a)) . 21
7.5.2.1.1 Method of measuring the power level in a specified load (for angle modulation) . 21
7.5.2.1.2 Method of measuring the power level in a specified load (for DSB and/or SSB) . 21
7.5.2.2 Method of measuring the effective radiated power (clause 7.5.1 b)) . 21
7.5.2.3 Method of measuring the effective radiated power (clause 7.5.1 c)) . 22
7.5.3 Limits . 22
7.6 Transient behaviour of the transmitter . 23
7.6.0 Applicability . 23
7.6.1 Definitions . 23
7.6.2 Method of measurement . 24
7.6.3 Limits . 26
8 Methods of measurement for receiver parameters . 26
8.1 Maximum usable sensitivity . 26
8.1.0 Applicability . 26
8.1.1 Definition . 26
8.1.2 Method of measurement . 26
8.1.3 Limits . 26
8.2 Adjacent channel selectivity . 26
8.2.0 Applicability . 26
8.2.1 Definition . 27
8.2.2 Method of measurement . 27
8.2.3 Limits . 27
8.3 Intermodulation response rejection . 27
8.3.0 Applicability . 27
8.3.1 Definition . 27
8.3.2 Method of measurement . 27
8.3.3 Limits . 28
8.4 Spurious radiations . 28
8.4.1 Definition . 28
8.4.2 Method of measurement . 28
8.4.2.1 Method of measuring the power level in a specified load . 28
8.4.2.2 Method of measuring the effective radiated power . 28
8.4.2.3 Method of measuring the effective radiated power . 29
8.4.3 Limits . 29
ETSI
---------------------- Page: 6 ----------------------
SIST EN 300 433 V2.1.1:2016
5 ETSI EN 300 433 V2.1.1 (2016-05)
8.5 Blocking and Spurious Response Rejection . 29
8.5.0 Applicability . 29
8.5.1 Definition . 29
8.5.2 Method of measurement . 30
8.5.3 Limits . 30
9 Testing for compliance with technical requirements . 30
9.1 Test conditions, power supply and ambient temperatures . 30
9.2 Interpretation of the measurement results . 30
Annex A (normative): Radiated measurement . 32
A.1 Test sites and general arrangements for measurements involving the use of radiated fields . 32
A.1.0 General . 32
A.1.1 Anechoic chamber . 32
A.1.2 Anechoic chamber with a conductive ground plane . 33
A.1.3 Open Area Test Site (OATS) . 34
A.1.4 Test antenna . 35
A.1.5 Substitution antenna . 36
A.1.6 Measuring antenna . 36
A.2 Guidance on the use of radiation test sites . 36
A.2.0 General . 36
A.2.1 Verification of the test site . 36
A.2.2 Preparation of the EUT . 36
A.2.3 Power supplies to the EUT . 36
A.2.4 Volume control setting for analogue speech tests . 37
A.2.5 Range length . 37
A.2.6 Site preparation . 37
A.3 Coupling of signals . 38
A.3.1 General . 38
A.3.2 Data signals . 38
A.3.3 Speech and analogue signals . 38
A.3.3.0 General . 38
A.3.3.1 Acoustic coupler description. 38
A.3.3.2 Calibration . 39
Annex B (normative): Specification for some particular measurement arrangements . 40
B.1 Power measuring receiver specification . 40
B.1.0 General . 40
B.1.1 IF filter . 40
B.1.2 Attenuation indicator . 41
B.1.3 RMS value indicator . 41
B.1.4 Oscillator and amplifier . 41
B.2 Spectrum analyser specification . 42
B.2.1 Adjacent and alternate channel power measurement . 42
B.2.2 Unwanted emissions measurement . 42
B.3 Integrating and power summing device . 42
Annex C (normative): Relationship between the present document and the essential
requirements of Directive 2014/53/EU . 43
History . 45
ETSI
---------------------- Page: 7 ----------------------
SIST EN 300 433 V2.1.1:2016
6 ETSI EN 300 433 V2.1.1 (2016-05)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (https://ipr.etsi.org/).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This Harmonised European Standard (EN) has been produced
...
ETSI EN 300 433 V2.1.1 (2016-05)
HARMONISED EUROPEAN STANDARD
Citizens' Band (CB) radio equipment;
Harmonised Standard covering the essential requirements
of article 3.2 of the Directive 2014/53/EU
---------------------- Page: 1 ----------------------
2 ETSI EN 300 433 V2.1.1 (2016-05)
Reference
REN/ERM-TGDMR-346
Keywords
CB, radio, testing
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2016.
All rights reserved.
TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.
TM
3GPP and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI
---------------------- Page: 2 ----------------------
3 ETSI EN 300 433 V2.1.1 (2016-05)
Contents
Intellectual Property Rights . 6
Foreword . 6
Modal verbs terminology . 6
1 Scope . 7
2 References . 7
2.1 Normative references . 7
2.2 Informative references . 8
3 Definitions, symbols and abbreviations . 8
3.1 Definitions . 8
3.2 Symbols . 9
3.3 Abbreviations . 9
4 General and operational requirements . 10
4.0 General . 10
4.1 Choice of model for testing . 10
4.1.0 General . 10
4.1.1 Auxiliary test equipment . 11
4.1.2 Declarations by the provider . 11
4.2 Testing of equipment that does not have an external 50 Ω RF connector (integral antenna equipment) . 11
4.3 Mechanical and electrical design . 11
4.3.1 General . 11
4.3.2 Controls . 11
4.3.3 PTT and voice- activated switch . 11
4.3.4 Combination with other equipment . 11
4.4 Operating frequencies . 12
4.5 Marking . 12
5 Test conditions, power sources and ambient temperatures . 12
5.0 Environmental profile . 12
5.1 Normal and extreme test conditions . 12
5.2 Test power source . 13
5.3 Normal test conditions . 13
5.3.1 Normal temperature and humidity . 13
5.3.2 Normal test power source . 13
5.3.2.1 Mains voltage . 13
5.3.2.2 Regulated lead-acid battery power sources used on vehicles . 13
5.3.2.3 Other power sources . 13
5.4 Extreme test conditions . 13
5.4.1 Extreme temperatures . 13
5.4.2 Extreme test power source . 14
5.4.2.1 Mains voltage . 14
5.4.2.2 Regulated lead-acid battery power sources used on vehicles . 14
5.4.2.3 Power sources using other types of batteries . 14
5.4.2.4 Other power sources . 14
5.5 Procedure for tests at extreme temperatures . 14
6 General test conditions . 14
6.1 Arrangements for test signals applied to the receiver input . 14
6.2 Receiver mute or squelch facility . 15
6.3 Receiver rated audio output power . 15
6.4 Transmitter rated RF power. 15
6.5 Normal test modulation . 15
6.5.1 DSB modulation . 15
6.5.2 SSB modulation . 15
6.5.3 Angle modulation (FM modulation with Preemphasis/Deemphasis) . 16
6.6 Artificial antenna . 16
6.7 Test fixture . 16
ETSI
---------------------- Page: 3 ----------------------
4 ETSI EN 300 433 V2.1.1 (2016-05)
6.8 Arrangement for test signals at the input of the transmitter . 16
6.9 Test site and general arrangements for radiated measurements. 16
7 Technical characteristics of the transmitter . 16
7.1 Frequency error . 16
7.1.0 Applicability . 16
7.1.1 Definition . 16
7.1.2 Method of measurement . 17
7.1.3 Limit . 17
7.2 Transmitter power . 17
7.2.1 Definition . 17
7.2.2 Method of measurement . 17
7.2.2.1 Method of measurement (conducted) . 17
7.2.2.2 Method of measurement (effective radiated power) . 17
7.2.3 Limits . 18
7.3 Maximum permissible frequency deviation . 18
7.3.0 Applicability . 18
7.3.1 Definition . 18
7.3.2 Method of measurement . 18
7.3.3 Limit . 19
7.4 Adjacent and alternate channel power . 19
7.4.1 Definition . 19
7.4.2 Method of measurement . 19
7.4.3 Limits . 20
7.5 Unwanted emissions in the spurious domain. 20
7.5.1 Definition . 20
7.5.2 Method of measurement . 21
7.5.2.1 Method of measuring the power level in a specified load (clause 7.5.1 a)) . 21
7.5.2.1.1 Method of measuring the power level in a specified load (for angle modulation) . 21
7.5.2.1.2 Method of measuring the power level in a specified load (for DSB and/or SSB) . 21
7.5.2.2 Method of measuring the effective radiated power (clause 7.5.1 b)) . 21
7.5.2.3 Method of measuring the effective radiated power (clause 7.5.1 c)) . 22
7.5.3 Limits . 22
7.6 Transient behaviour of the transmitter . 23
7.6.0 Applicability . 23
7.6.1 Definitions . 23
7.6.2 Method of measurement . 24
7.6.3 Limits . 26
8 Methods of measurement for receiver parameters . 26
8.1 Maximum usable sensitivity . 26
8.1.0 Applicability . 26
8.1.1 Definition . 26
8.1.2 Method of measurement . 26
8.1.3 Limits . 26
8.2 Adjacent channel selectivity . 26
8.2.0 Applicability . 26
8.2.1 Definition . 27
8.2.2 Method of measurement . 27
8.2.3 Limits . 27
8.3 Intermodulation response rejection . 27
8.3.0 Applicability . 27
8.3.1 Definition . 27
8.3.2 Method of measurement . 27
8.3.3 Limits . 28
8.4 Spurious radiations . 28
8.4.1 Definition . 28
8.4.2 Method of measurement . 28
8.4.2.1 Method of measuring the power level in a specified load . 28
8.4.2.2 Method of measuring the effective radiated power . 28
8.4.2.3 Method of measuring the effective radiated power . 29
8.4.3 Limits . 29
ETSI
---------------------- Page: 4 ----------------------
5 ETSI EN 300 433 V2.1.1 (2016-05)
8.5 Blocking and Spurious Response Rejection . 29
8.5.0 Applicability . 29
8.5.1 Definition . 29
8.5.2 Method of measurement . 30
8.5.3 Limits . 30
9 Testing for compliance with technical requirements . 30
9.1 Test conditions, power supply and ambient temperatures . 30
9.2 Interpretation of the measurement results . 30
Annex A (normative): Radiated measurement . 32
A.1 Test sites and general arrangements for measurements involving the use of radiated fields . 32
A.1.0 General . 32
A.1.1 Anechoic chamber . 32
A.1.2 Anechoic chamber with a conductive ground plane . 33
A.1.3 Open Area Test Site (OATS) . 34
A.1.4 Test antenna . 35
A.1.5 Substitution antenna . 36
A.1.6 Measuring antenna . 36
A.2 Guidance on the use of radiation test sites . 36
A.2.0 General . 36
A.2.1 Verification of the test site . 36
A.2.2 Preparation of the EUT . 36
A.2.3 Power supplies to the EUT . 36
A.2.4 Volume control setting for analogue speech tests . 37
A.2.5 Range length . 37
A.2.6 Site preparation . 37
A.3 Coupling of signals . 38
A.3.1 General . 38
A.3.2 Data signals . 38
A.3.3 Speech and analogue signals . 38
A.3.3.0 General . 38
A.3.3.1 Acoustic coupler description. 38
A.3.3.2 Calibration . 39
Annex B (normative): Specification for some particular measurement arrangements . 40
B.1 Power measuring receiver specification . 40
B.1.0 General . 40
B.1.1 IF filter . 40
B.1.2 Attenuation indicator . 41
B.1.3 RMS value indicator . 41
B.1.4 Oscillator and amplifier . 41
B.2 Spectrum analyser specification . 42
B.2.1 Adjacent and alternate channel power measurement . 42
B.2.2 Unwanted emissions measurement . 42
B.3 Integrating and power summing device . 42
Annex C (normative): Relationship between the present document and the essential
requirements of Directive 2014/53/EU . 43
History . 45
ETSI
---------------------- Page: 5 ----------------------
6 ETSI EN 300 433 V2.1.1 (2016-05)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (https://ipr.etsi.org/).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This Harmonised European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic
compatibility and Radio spectrum Matters (ERM).
The present document has been prepared under the Commission's standardisation request C(2015) 5376 final [i.5] to
provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation
of the laws of the Member States relating to the making available on the market of radio equipment and repealing
Directive 1999/5/EC [i.4].
Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with
the normative clauses of the present document given in table C.1 confers, within the limits of the scope of the present
document, a presumption of conformity with the corresponding essential requirements of that Directive, and associated
EFTA regulations.
National transposition dates
Date of adoption of this EN: 2 May 2016
Date of
...
Draft ETSI EN 300 433 V2.1.0 (2016-02)
HARMONISED EUROPEAN STANDARD
Citizens' Band (CB) radio equipment;
Harmonised Standard covering the essential requirements
of article 3.2 of the Directive 2014/53/EU
---------------------- Page: 1 ----------------------
2 Draft ETSI EN 300 433 V2.1.0 (2016-02)
Reference
REN/ERM-TGDMR-346
Keywords
CB, radio, testing
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2016.
All rights reserved.
TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.
TM
3GPP and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI
---------------------- Page: 2 ----------------------
3 Draft ETSI EN 300 433 V2.1.0 (2016-02)
Contents
Intellectual Property Rights . 6
Foreword . 6
Modal verbs terminology . 6
1 Scope . 7
2 References . 7
2.1 Normative references . 7
2.2 Informative references . 8
3 Definitions, symbols and abbreviations . 8
3.1 Definitions . 8
3.2 Symbols . 9
3.3 Abbreviations . 9
4 General and operational requirements . 10
4.0 General . 10
4.1 Choice of model for testing . 10
4.1.0 General . 10
4.1.1 Auxiliary test equipment . 11
4.1.2 Declarations by the provider . 11
4.2 Testing of equipment that does not have an external 50 Ω RF connector (integral antenna equipment) . 11
4.3 Mechanical and electrical design . 11
4.3.1 General . 11
4.3.2 Controls . 11
4.3.3 PTT and voice- activated switch . 11
4.3.4 Combination with other equipment . 11
4.4 Operating frequencies . 12
4.5 Marking . 12
5 Test conditions, power sources and ambient temperatures . 12
5.0 Environmental profile . 12
5.1 Normal and extreme test conditions . 12
5.2 Test power source . 13
5.3 Normal test conditions . 13
5.3.1 Normal temperature and humidity . 13
5.3.2 Normal test power source . 13
5.3.2.1 Mains voltage . 13
5.3.2.2 Regulated lead-acid battery power sources used on vehicles . 13
5.3.2.3 Other power sources . 13
5.4 Extreme test conditions . 13
5.4.1 Extreme temperatures . 13
5.4.2 Extreme test power source . 14
5.4.2.1 Mains voltage . 14
5.4.2.2 Regulated lead-acid battery power sources used on vehicles . 14
5.4.2.3 Power sources using other types of batteries . 14
5.4.2.4 Other power sources . 14
5.5 Procedure for tests at extreme temperatures . 14
6 General test conditions . 14
6.1 Arrangements for test signals applied to the receiver input . 14
6.2 Receiver mute or squelch facility . 15
6.3 Receiver rated audio output power . 15
6.4 Transmitter rated RF power. 15
6.5 Normal test modulation . 15
6.5.1 DSB modulation . 15
6.5.2 SSB modulation . 15
6.5.3 Angle modulation (FM modulation with Preemphasis/Deemphasis) . 16
6.6 Artificial antenna . 16
6.7 Test fixture . 16
ETSI
---------------------- Page: 3 ----------------------
4 Draft ETSI EN 300 433 V2.1.0 (2016-02)
6.8 Arrangement for test signals at the input of the transmitter . 16
6.9 Test site and general arrangements for radiated measurements. 16
7 Technical characteristics of the transmitter . 16
7.1 Frequency error . 16
7.1.0 Applicability . 16
7.1.1 Definition . 16
7.1.2 Method of measurement . 17
7.1.3 Limit . 17
7.2 Transmitter power . 17
7.2.1 Definition . 17
7.2.2 Method of measurement . 17
7.2.2.1 Method of measurement (conducted) . 17
7.2.2.2 Method of measurement (effective radiated power) . 17
7.2.3 Limits . 18
7.3 Maximum permissible frequency deviation . 18
7.3.0 Applicability . 18
7.3.1 Definition . 18
7.3.2 Method of measurement . 18
7.3.3 Limit . 19
7.4 Adjacent and alternate channel power . 19
7.4.1 Definition . 19
7.4.2 Method of measurement . 19
7.4.3 Limits . 20
7.5 Unwanted emissions in the spurious domain. 20
7.5.1 Definition . 20
7.5.2 Method of measurement . 21
7.5.2.1 Method of measuring the power level in a specified load (clause 7.5.1 a)) . 21
7.5.2.1.1 Method of measuring the power level in a specified load (for angle modulation) . 21
7.5.2.1.2 Method of measuring the power level in a specified load (for DSB and/or SSB) . 21
7.5.2.2 Method of measuring the effective radiated power (clause 7.5.1 b)) . 21
7.5.2.3 Method of measuring the effective radiated power (clause 7.5.1 c)) . 22
7.5.3 Limits . 22
7.6 Transient behaviour of the transmitter . 23
7.6.0 Applicability . 23
7.6.1 Definitions . 23
7.6.2 Method of measurement . 24
7.6.3 Limits . 26
8 Methods of measurement for receiver parameters . 26
8.1 Maximum usable sensitivity . 26
8.1.0 Applicability . 26
8.1.1 Definition . 26
8.1.2 Method of measurement . 26
8.1.3 Limits . 26
8.2 Adjacent channel selectivity . 26
8.2.0 Applicability . 26
8.2.1 Definition . 27
8.2.2 Method of measurement . 27
8.2.3 Limits . 27
8.3 Intermodulation response rejection . 27
8.3.0 Applicability . 27
8.3.1 Definition . 27
8.3.2 Method of measurement . 27
8.3.3 Limits . 28
8.4 Spurious radiations . 28
8.4.1 Definition . 28
8.4.2 Method of measurement . 28
8.4.2.1 Method of measuring the power level in a specified load . 28
8.4.2.2 Method of measuring the effective radiated power . 28
8.4.2.3 Method of measuring the effective radiated power . 29
8.4.3 Limits . 29
ETSI
---------------------- Page: 4 ----------------------
5 Draft ETSI EN 300 433 V2.1.0 (2016-02)
8.5 Blocking and Spurious Response Rejection . 29
8.5.0 Applicability . 29
8.5.1 Definition . 29
8.5.2 Method of measurement . 30
8.5.3 Limits . 30
9 Testing for compliance with technical requirements . 30
9.1 Test conditions, power supply and ambient temperatures . 30
9.2 Interpretation of the measurement results . 30
Annex A (normative): Radiated measurement . 32
A.1 Test sites and general arrangements for measurements involving the use of radiated fields . 32
A.1.0 General . 32
A.1.1 Anechoic chamber . 32
A.1.2 Anechoic chamber with a conductive ground plane . 33
A.1.3 Open Area Test Site (OATS) . 34
A.1.4 Test antenna . 35
A.1.5 Substitution antenna . 35
A.1.6 Measuring antenna . 36
A.2 Guidance on the use of radiation test sites . 36
A.2.0 General . 36
A.2.1 Verification of the test site . 36
A.2.2 Preparation of the EUT . 36
A.2.3 Power supplies to the EUT . 36
A.2.4 Volume control setting for analogue speech tests . 36
A.2.5 Range length . 37
A.2.6 Site preparation . 37
A.3 Coupling of signals . 38
A.3.1 General . 38
A.3.2 Data signals . 38
A.3.3 Speech and analogue signals . 38
A.3.3.0 General . 38
A.3.3.1 Acoustic coupler description. 38
A.3.3.2 Calibration . 39
Annex B (normative): Specification for some particular measurement arrangements . 40
B.1 Power measuring receiver specification . 40
B.1.0 General . 40
B.1.1 IF filter . 40
B.1.2 Attenuation indicator . 41
B.1.3 RMS value indicator . 41
B.1.4 Oscillator and amplifier . 41
B.2 Spectrum analyser specification . 42
B.2.1 Adjacent and alternate channel power measurement . 42
B.2.2 Unwanted emissions measurement . 42
B.3 Integrating and power summing device . 42
Annex C (normative): Relationship between the present document and the essential
requirements of Directive 2014/53/EU . 43
History . 45
ETSI
---------------------- Page: 5 ----------------------
6 Draft ETSI EN 300 433 V2.1.0 (2016-02)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (https://ipr.etsi.org/).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This draft Harmonised European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic
compatibility and Radio spectrum Matters (ERM), and is now submitted for the combined Public Enquiry and Vote
phase of the ETSI standards EN Approval Procedure.
The present document has been prepared under the Commission's standardisation request C(2015) 5376 final [i.5] to
provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation
of the laws of the Member States relating to the making available on the market of radio equipment and repealing
Directive 1999/5/EC [i.4].
Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with
the normative clauses of the present document given in table C.1 confers, within the limits of the scope of the present
document, a presumption of conformity with the corresponding essential r
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.