SIST EN 61076-2-001:2007
(Main)Connectors for electronic equipment -- Part 2-001: Circular connectors - Blank detail specification
Connectors for electronic equipment -- Part 2-001: Circular connectors - Blank detail specification
Shall contain information which contributes to a proper application of the connectors. It will also provide specifics for a better understanding of the detail specification.
Steckverbinder für elektronische Einrichtungen -- Teil 2-001: Rundsteckverbinder - Vordruck für Bauartspezifikation
Connecteurs pour équipements électroniques -- Partie 2-001: Connecteurs circulaires - Spécification particulière cadre
Cette publication porte également le numéro QC 480101, qui est le numéro de spécification dans le système CEI d'assurance de la qualité des composants électroniques (IECQ).
Konektorji za elektronsko opremo - 2-001. del: Okrogli konektorji - Okvirna podrobna specifikacija (IEC 61076-2-001:2001)
General Information
Relations
Standards Content (Sample)
6,67(16/29(16.,MDQXDU67$1'$5'LVWRYHWHQ(1.RQHNWRUML]DHOHNWURQVNRRSUHPRGHO2NURJOLNRQHNWRUML2NYLUQDSRGUREQDVSHFLILNDFLMD,(&&RQQHFWRUVIRUHOHFWURQLFHTXLSPHQW3DUW&LUFXODUFRQQHFWRUV%ODQNGHWDLOVSHFLILFDWLRQ,(& !"#$%&'( )&!*- . 5HIHUHQþQDãWHYLOND6,67(1HQ,&6
EUROPEAN STANDARDEN 61076-2-001NORME EUROPÉENNEEUROPÄISCHE NORMDecember 2001CENELECEuropean Committee for Electrotechnical StandardizationComité Européen de Normalisation ElectrotechniqueEuropäisches Komitee für Elektrotechnische NormungCentral Secretariat: rue de Stassart 35, B - 1050 Brussels© 2001 CENELEC -All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.Ref. No. EN 61076-2-001:2001 EICS 31.220.10English versionConnectors for electronic equipmentPart 2-001: Circular connectors -Blank detail specification(IEC 61076-2-001:2001)Connecteurs pour équipementsélectroniquesPartie 2-001: Connecteurs circulaires -Spécification particulière cadre(CEI 61076-2-001:2001)Steckverbinder für elektronischeEinrichtungenTeil 2-001: Rundsteckverbinder -Vordruck für Bauartspezifikation(IEC 61076-2-001:2001)This European Standard was approved by CENELEC on 2001-12-01. CENELEC members are bound tocomply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration.Up-to-date lists and bibliographical references concerning such national standards may be obtained onapplication to the Central Secretariat or to any CENELEC member.This European Standard exists in three official versions (English, French, German). A version in any otherlanguage made by translation under the responsibility of a CENELEC member into its own language andnotified to the Central Secretariat has the same status as the official versions.CENELEC members are the national electrotechnical committees of Austria, Belgium, Czech Republic,Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands,Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.
EN 61076-2-001:2001- 2 -ForewordThe text of document 48B/1085/FDIS, future edition 1 of IEC 61076-2-001, prepared by SC 48B,Connectors, of IEC TC 48, Electromechanical components and mechanical structures for electronicequipment, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC asEN 61076-2-001 on 2001-12-01.The following dates were fixed:–latest date by which the EN has to be implementedat national level by publication of an identicalnational standard or by endorsement(dop)2002-09-01–latest date by which the national standards conflictingwith the EN have to be withdrawn(dow)2001-12-01Annexes designated "normative" are part of the body of the standard.In this standard, annexes A and ZA are normative.Annex ZA has been added by CENELEC.__________Endorsement noticeThe text of the International Standard IEC 61076-2-001:2001 was approved by CENELEC as aEuropean Standard without any modification.__________
- 3 -EN 61076-2-001:2001Annex ZA(normative)Normative references to international publicationswith their corresponding European publicationsThis European Standard incorporates by dated or undated reference, provisions from otherpublications. These normative references are cited at the appropriate places in the text and thepublications are listed hereafter. For dated references, subsequent amendments to or revisions of anyof these publications apply to this European Standard only when incorporated in it by amendment orrevision. For undated references the latest edition of the publication referred to applies (includingamendments).NOTEWhen an international publication has been modified by common modifications, indicated by (mod), the relevantEN/HD applies.PublicationYearTitleEN/HDYearIEC 60917SeriesModular order for the development ofmechanical structures for electronicequipment practicesEN 60917SeriesIEC 61076-2- 1)Connectors for use in d.c. low-frequency analogue and in digitalhigh-speed data applicationsPart 2: Circular connectors withassessed quality - SectionalspecificationEN 61076-21999 2)
1) Undated reference.2) Valid edition at time of issue.
NORMEINTERNATIONALECEIIECINTERNATIONALSTANDARD61076-2-001QC 480101Première éditionFirst edition2001-10Connecteurs pour équipements électroniques –Partie 2-001:Connecteurs circulaires –Spécification particulière cadreConnectors for electronic equipment –Part 2-001:Circular connectors –Blank detail specification Commission Electrotechnique Internationale International Electrotechnical CommissionPour prix, voir catalogue en vigueurFor price, see current catalogue IEC 2001
Droits de reproduction réservés
Copyright - all rights reservedAucune partie de cette publication ne peut être reproduite niutilisée sous quelque forme que ce soit et par aucun procédé,électronique ou mécanique, y compris la photocopie et lesmicrofilms, sans l'accord écrit de l'éditeur.No part of this publication may be reproduced or utilized inany form or by any means, electronic or mechanical,including photocopying and microfilm, without permission inwriting from the publisher.International Electrotechnical Commission3, rue de Varembé
Geneva, SwitzerlandTelefax: +41 22 919 0300e-mail: inmail@iec.ch IEC web site
http://www.iec.chCODE PRIXPRICE CODEXB
61076-2-001 © IEC:2001– 3 –CONTENTSFOREWORD .7INTRODUCTION.111General information.151.1Scope.151.2Number of contacts or contact cavities.151.2.1Rear or panes mounting for fixed connectors.151.2.2Contact mounting for fixed, front or rear release.151.3Ratings and characteristics.151.4Normative references.181.5Marking.181.6IEC type designation.221.7Ordering information.222Technical information.262.1Definitions.262.2Survey of styles and variants.262.3Information on application.262.3.1Complete connectors (pairs).262.3.2Fixed connectors.262.3.3Free connectors.262.3.4Accessories.302.3.5Shielding/grounding.302.3.6Basic type of terminations.302.4Contact arrangements.303Drawings and dimensions.343.1General.343.2Isometric view and common features.343.2.1Common features.383.2.2Height dimensions.383.2.3Depth dimensions.383.3Engagement (mating) information.423.3.1Engaging (mating) direction.423.3.2Inclination.423.4Fixed connectors.423.4.1Dimensions.423.4.2Terminations.423.5Free connectors.463.5.1Dimensions.463.5.2Terminations.463.6Accessories.463.7Mounting information for fixed connectors.463.7.1Mounting on printed boards.463.7.2Mounting on panels.503.8Assembly information for free connectors.50
61076-2-001 © IEC:2001– 5 –3.9Gauges.503.9.1Sizing gauges and retention force gauges.503.9.2Endurance, engaging/separating/insertion/withdrawal force gauges.543.9.3Probes.543.9.4Test panel (for voltage proof test).544Characteristics.584.1Climatic category.584.2Electrical.584.2.1Creepage and clearance distances.584.2.2Voltage proof.584.2.3Current-carrying capacity.624.2.4Contact resistance.624.2.5Insulation resistance.624.3Mechanical.624.3.1Mechanical operation.624.3.2Engaging and separating forces (or insertion and withdrawal forces).664.3.3Contact retention in insert.664.3.4Polarizing method.665Test schedule.705.1General.705.1.1Arrangement for contact resistance measurement.705.1.2Arrangement for dynamic stress tests.705.1.3Arrangement for testing static load, axial.705.1.4Wiring of specimens.705.2Test schedules.745.2.1Basic (minimum) test schedule.745.2.2Full test schedule.786Quality assessment procedures.134Annex A (normative)
New test and additional test phases.137
61076-2-001 © IEC:2001– 7 –INTERNATIONAL ELECTROTECHNICAL COMMISSION___________CONNECTORS FOR ELECTRONIC EQUIPMENT –Part 2-001: Circular connectors –Blank detail specificationFOREWORD1)The IEC (International Electrotechnical Commission) is a worldwide organization for standardization comprisingall national electrotechnical committees (IEC National Committees). The object of the IEC is to promoteinternational co-operation on all questions concerning standardization in the electrical and electronic fields. Tothis end and in addition to other activities, the IEC publishes International Standards. Their preparation isentrusted to technical committees; any IEC National Committee interested in the subject dealt with mayparticipate in this preparatory work. International, governmental and non-governmental organizations liaisingwith the IEC also participate in this preparation. The IEC collaborates closely with the International Organizationfor Standardization (ISO) in accordance with conditions determined by agreement between the twoorganizations.2)The formal decisions or agreements of the IEC on technical matters express, as nearly as possible, aninternational consensus of opinion on the relevant subjects since each technical committee has representationfrom all interested National Committees.3)The documents produced have the form of recommendations for international use and are published in the formof standards, technical specifications, technical reports or guides and they are accepted by the NationalCommittees in that sense.4)
In order to promote international unification, IEC National Committees undertake to apply IEC InternationalStandards transparently to the maximum extent possible in their national and regional standards. Anydivergence between the IEC Standard and the corresponding national or regional standard shall be clearlyindicated in the latter.5)
The IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for anyequipment declared to be in conformity with one of its standards.6)
Attention is drawn to the possibility that some of the elements of this International Standard may be the subjectof patent rights. The IEC shall not be held responsible for identifying any or all such patent rights.International Standard IEC 61076-2-001 has been prepared by subcommittee 48B: Connectors,of IEC technical committee 48: Electromechanical components and mechanical structures forelectronic equipment.The text of this standard is based on the following documents:FDISReport on Voting48B/1085/FDIS48B/1116/RVDFull information for the approval of this standard can be found in the report on voting indicatedin the above table.Future standards in this series will carry the new general title as cited above. Titles of existingstandards in this series will be updated when a new edition is prepared.This publication has been drafted in accordance with the ISO/IEC Directives, Part 3.Annex A forms an integral part of this specification.The QC number that appears on the front cover of this publication is the specification numberof the IEC Quality Assessment System for Electronic Components (IECQ).
61076-2-001 © IEC:2001– 9 –It should be used in conjunction with the applicable sectional specification, see 1.1 of IEC 61076-2.The committee has decided that the contents of this publication will remain unchanged until2002. At this date, the publication will be•reconfirmed;•withdrawn;•replaced by a revised edition, or•amended.
61076-2-001 © IEC:2001– 11 –INTRODUCTIONIn prior years, IEC subcommittee 48B had prepared detail specifications as part of a two-leveldocument system. When the IECQ system was introduced, SC 48B was urged to considerchanging to the four-level specification system as described in IEC Guide 102. This blank detailspecification is part of that four-level document system.This blank detail specification is a supplementary document to the sectional specificationIEC 61076-2 and contains requirements for style, lay-out, and the minimum content of detailspecifications.For the scope and definition of this blank detail specification, see 1.2 of IEC 61076-1 and 1.1 ofIEC 61076-2.Detail specifications not complying with these requirements should not be considered as beingin accordance with the IECQ system, and should not be so described.The complete requirements for the circular connectors described herein should correspond tothis blank detail specification and the current issues of IEC 61076-1 and IEC 61076-2.In the preparation of detail specifications, the contents of 1.2.3 of IEC 61076-1 should be takeninto account.NOTE
In order to facilitate the use of this standard, ‘Guidance notes’ are provided on the left page and thematching clause numbers are on the right page. French pages are followed immediately by English pages. The‘Guidance notes’ are provided to aid the specification preparer in writing a more complete and accurate document.They represent the minimum information necessary. The specification preparer is encouraged to add figures oradditional text that will make the requirements clearer to the user.
– 14 –61076-2-001 IEC:2001Guidance notesThe following pages give a recommended layout of a detail specification. The contents of thispage give guidance on the information which should wherever possible be given on the frontpage of a detail specification (see IEC Guide 102).For the scope and definition of a detail specification, see 1.2.3 of IEC 61076-1.The numbers between brackets on the front page of the detail specification correspond to thefollowing information.Identification of the detail specification(1)The International Electrotechnical Commission or the National Standards Organizationunder whose authority the detail specification is drafted. It should also be stated where thedetail specification can be obtained.(2)The IECQ QC number of the detail specification and date of issue.(3)The IECQ QC number and issue number of the generic specification.(4)Any information required by the national systems.Identification of the connector(5)A short description of the type of connector.(6)Information on the typical construction of the connector, for example it should be statedwhether or not the connector is suitable for mounting on panels.(7)Outline drawing, preferably of isometric or similar projection, from which the connector maybe clearly identified.(8)Information on performance level(s) and assessment level(s) specified in the document.(9)Reference data on the most important properties, to allow comparison between the variousconnector types.NOTE
It may be convenient for some of this information to be given in tabular form.
61076-2-001 © IEC:2001– 15 –[1]IECQ/IECDetail specification number[2]Generic specification numberElectronic components of assessed quality in accordance with:[3]National number of detailspecification(it is not necessary to use this if theIECQ/IEC number is identical)[4]Outline drawing[7]Product description[5][6][8]Performance level(s):Assessment level(s):Combination ofperformance levelsand assessment levels:Reference data[9]Information on the availability of components qualified to this detail specification is given in the qualifiedproducts lists.1 General information1.1 ScopeThis part of IEC 61076 establishes uniform specifications, type testing requirements and qualityassessment procedures for a subfamily of circular connectors.1.2 Number of contacts or contact cavities1.2.1 Rear or panes mounting for fixed connectors1.2.2 Contact mounting for fixed, front or rear release1.3 Ratings and characteristicsRated voltageCurrent-carrying capacity Insulation resistanceClimatic categoryCreepage and clearance distances
– 18 –61076-2-001 IEC:2001Guidance notes1.4 Normative referencesIt may be necessary to make reference to other documents in addition to those stated, in whichcase the list of related documents will be extended beyond those referenced.Where reference is made to standards already listed in IEC 61076-1 and IEC 61076-2, suchlisting shall not be repeated in 1.4 of the detail specification.1.5 MarkingThe marking of the connector and the package shall be in accordance with 2.6 of IEC 61076-1.
61076-2-001 © IEC:2001– 19 –1.4
Normative referencesThe following normative documents contain provisions which, through reference in this text,constitute provisions of this part of IEC 61076. For dated references, subsequent amendmentsto, or revisions of, any of these publications do not apply. However, parties to agreementsbased on this part of IEC 61076 are encouraged to investigate the possibility of applying themost recent editions of the normative documents indicated below. For undated references, thelatest edition of the normative document referred to applies. Members of IEC and ISO maintainregisters of currently valid International Standards.IEC 60917 (all parts), Modular order for the development of mechanical structures forelectronic equipment practicesIEC 61076-2, Connectors for use in d.c., low frequency analogue and digital high speed dataapplications – Part 2: Circular connectors with assessed quality – Sectional specification1.5
Marking
– 22 –61076-2-001 IEC:2001Guidance notes1.6 IEC type designationThe designation shall be derived in accordance with 2.5 of IEC 61076-2:Example: IEC61076-2-XXLLNNLLL or NL or NNLLetter denoting style ofconnectorLetter denoting housing or body sizeTwo numbers denoting the insertarrangementLetter denoting the type of contactMFHLetter denoting the type of terminationESPCWILetter or number denoting contact polarizationLetter or number denoting the variant codeNumber and letter denoting performance level (PL) and assessment level (AL)respectively1.7 Ordering informationFor ordering connectors according to this detail specification, the type designation described in1.6 shall be used.
61076-2-001 © IEC:2001– 23 –1.6
IEC type designation1.7
Ordering information
– 26 –61076-2-001 IEC:2001Guidance notes2 Technical informationThe detail specification shall contain information which contributes to a proper application ofthe connectors. It will also provide specifics for a better understanding of the detailspecification.2.1 DefinitionsIn addition to the terminology used in and applicable to the detail specification, as stated in 2.1of IEC 61076-2, it is recommended to list those definitions which are particular to theconnectors specified in the detail specification.2.2 Survey of styles and variantsShould the detail specification be applicable to a range of styles and/or variants, a survey ofthe range covered shall be included in the form of a table in the detail specification. The tableshown, table "1", may be amended to include additional and or alternative details if this isapplicable in describing the styles and variants.NOTE
Tables used in detail specifications shall be numbered in sequence, the numbering in this standard hasbeen used as an example and therefore numbered as "x" using inverted commas.2.3 Information on applicationIf required, rules and recommendations for the use of the connectors specified in the detailspecification shall, unless sufficiently covered by dimensional information in clause 3, be listedfor:2.3.1 Complete connectors (pairs)2.3.2 Fixed connectors2.3.3 Free connectorsNOTE
The category of free connectors includes free coupler connectors. These connectors have coupling orlatching hardware as an integral part of the connector. Information about the coupling hardware should be included,as necessary, in this clause and in clauses 3 and 5.
61076-2-001 © IEC:2001– 27 –2
Technical information2.1
Definitions2.2
Survey of styles and variantsTable "1" – Styles and variantsConnector styleandnumber of contactsStyle reference letter2.3
Information on application2.3.1
Complete connectors (pairs)2.3.2
Fixed connectors2.3.3
Free connectors
– 30 –61076-2-001 IEC:2001Guidance notes2.3.4AccessoriesWhen accessories provide an essential support to the application of the connectors, thefeatures and use shall be outlined in the detail specification, where applicable.2.3.4.1Special contactsIn the case where special contacts are used in conjunction with the contacts specified in thedetail specification, information on these contacts shall be presented "for information only",given the fact that no detail specification of such contacts has been published. Special contactsare defined as usually removable contacts for high-current, high-voltage, RF, filter or FOapplications.2.3.4.2
Coding devicesWhen coding devices which are not an integral part of the connector are used, separateinformation shall be given in the detail specification.2.3.4.3
Mounting devicesWhen mounting devices which do not form an integral part of the connector are recommended,information on these devices shall be presented in the detail specification for reference only.2.3.5
Shielding/groundingWhen shielding and/or grounding features which cannot be considered as an integral part ofthe connector or an accessory are offered, information shall be given in the detail specification.2.3.6
Basic type of terminationsWhen different types of terminations are possible, information on their use shall be presentedin the detail specification in a tabular form. More detailed dimensional information may beprovided in those parts of the detail specification which describe the dimensions of fixed andfree connectors.If no significant differences occur between terminations of fixed and free connectors, theinformation may be included in this subclause instead.2.4 Contact arrangementsWhen different mechanical contact loading per connector insert is possible and influences theintended application of the connector, information shall be given in the detail specification,preferably in the form of drawings or tables. These arrangements shall be specified by theappropriate combination of the IEC type designation specified in 1.6 of the detail specification.
61076-2-001 © IEC:2001– 31 –2.3.4
Accessories2.3.4.1
Special contacts2.3.4.2
Coding devices2.3.4.3
Mounting devices2.3.5
Shielding/grounding2.3.6
Basic type of terminations2.4
Contact arrangements
– 34 –61076-2-001 IEC:2001Guidance notes3 Drawings and dimensionsIn order to facilitate comparison of various specifications, a uniform presentation of drawinginformation is recommended in accordance with 2.7.1 of IEC 61076-1:Drawings and dimensions shall cover:a)isometric view showing the basic design including common features of related connectors;b)fixed connectors;c)free connectorsd)mating information;e)accessories;f)mounting information for fixed connectors;g)assembly information for free connectors;h)assembly information for connectors with accessories;i)testing gauges, probes and test panels.3.1 GeneralIt shall be stated in the detail specification if original dimensions are millimetres or inches.It shall be stated in the detail specification if drawings are shown in first angle or in third angleprojection.The system of lettering shall be as described by 2.7.1.1 of IEC 61076-1.The following statement shall be included in the detail specification:The shape of the connectors may deviate from those given in the following drawings aslong as the specified dimensions are not influenced.Wherever practical, the same dimension letters shall be used for corresponding dimensions offixed and free connectors.3.2 Isometric view and common featuresAn isometric view shall be included and shall show the main characteristics of the designincluding common features, if applicable.It is convenient to show the dimension reference, the dimension and the feature description inthe form of a table, see table "2".
61076-2-001 © IEC:2001– 35 –3
Drawings and dimensions3.1
GeneralThe shape of the connectors may deviate from those given in the following drawings as long asthe specified dimensions are not influenced.3.2
Isometric view and common featuresTable "2" – Isometric view and common featuresReferenceDimensionFeature description
– 38 –61076-2-001 IEC:2001Guidance notes3.2.1 Common featuresA description of all the common features relating to the style of connectors covered by thedetail specification shall be included.Data which could be specified include:a)the datum point or datum line and a reference to the datum;b) position of the mounting hole(s) of the fixed connector;c) position of the terminations of the fixed connector;d) position of the printed board;e) position of the
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.