SIST EN 61076-2-001:2011
Connectors for electronic equipment - Product requirements - Part 2-001: Circular connectors - Blank detail specification
Connectors for electronic equipment - Product requirements - Part 2-001: Circular connectors - Blank detail specification
It may be necessary to refer to other documents in addition to those stated, in which case the list of related documents shall be extended beyond those referenced. If standards are referenced which are already listed in IEC 61076-1 and IEC 61076-2, their reference shall not be repeated in 1.2 of the detail product specification.
Steckverbinder für elektronische Einrichtungen - Produktanforderungen - Teil 2-001: Rundsteckverbinder - Vordruck für Bauartspezifikation
Connecteurs pour équipements électroniques - Exigences de produit - Partie 2-001: Connecteurs circulaires - Spécification particulière-cadre
La CEI 61076-2-001:2011 La présente spécification particulière cadre de produit est un document qui complète la spécification intermédiaire de produit CEI 61076-2 et contient des exigences pour le modèle, la présentation et le contenu des spécifications particulières de produit pour les connecteurs circulaires. Il convient qu'elle soit utilisée dans la conjonction avec les publications suivantes: la CEI 61076-1 et la CEI 61076-2 pour les exigences de produit ainsi que la CEI 62197-1 pour les exigences de qualité. Les pages d'échantillon peuvent être servir de modèle lors de la préparation d'une spécification particulière de produit couverte par le présent document. Le présent document n'est pas destiné à remplacer les modèles ni les guides de présentation de la CEI, mais à aider à les utiliser. Il est rappelé à tous les utilisateurs de respecter les directives et les lignes directrices applicables de la CEI lors de la préparation d'une norme. La présente Norme internationale annule et remplace la première édition de la CEI 61076-2-001 (2001). Cette édition constitue une révision technique. La présente édition contient les importantes modifications techniques suivantes par rapport à la précédente édition: - La présente Norme internationale ne contient pas les procédures d'assurance de la qualité. Comme cela est décrit dans les normes CEI 61076-1 et CEI 62197-1, une nouvelle structure de document a été établie. La CEI 61076-2-001 a été révisée pour refléter cette structure mise à jour. - Le paragraphe 3.2, Systèmes de niveaux a été ajouté. - Le paragraphe Désignation de type CEI a été retiré. - Les Articles 4 Informations dimensionnelles et 5 Caractéristiques ont été ajoutés. - Certains Articles et groupes d'essai ont été réorganisés. Le groupe d'essai HP a été ajouté.",PE
Konektorji za elektronsko opremo - Zahteve za izdelke - 2-001. del: Okrogli konektorji - Okvirna podrobna specifikacija
Poleg navedenih dokumentov so lahko potrebni sklici na druge dokumente in v tem primeru se povezani dokumenti razširijo prek navedenih. Če so narejeni sklici na standarde, ki so že navedeni v IEC 61076-1 in IEC 61076-2, se sklici v točki 1.2 podrobne specifikacije izdelka ne ponovijo.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 61076-2-001:2011
01-oktober-2011
Konektorji za elektronsko opremo - Zahteve za izdelke - 2-001. del: Okrogli
konektorji - Okvirna podrobna specifikacija
Connectors for electronic equipment - Product requirements - Part 2-001: Circular
connectors - Blank detail specification
Connecteurs pour équipements électroniques - Exigences de produit - Partie 2-001:
Connecteurs circulaires - Spécification particulière-cadre
Ta slovenski standard je istoveten z: EN 61076-2-001:2011
ICS:
31.220.10 9WLþLLQYWLþQLFHNRQHNWRUML Plug-and-socket devices.
Connectors
SIST EN 61076-2-001:2011 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 61076-2-001:2011
---------------------- Page: 2 ----------------------
SIST EN 61076-2-001:2011
EUROPEAN STANDARD
EN 61076-2-001
NORME EUROPÉENNE
August 2011
EUROPÄISCHE NORM
ICS 31.220.10 Supersedes EN 61076-2-001:2001
English version
Connectors for electronic equipment -
Product requirements -
Part 2-001: Circular connectors -
Blank detail specification
(IEC 61076-2-001:2011)
Connecteurs pour équipements Steckverbinder für elektronische
électroniques - Einrichtungen -
Exigences de produit - Produktanforderungen -
Partie 2-001: Connecteurs circulaires - Teil 2-001: Rundsteckverbinder -
Spécification particulière cadre Vordruck für Bauartspezifikation
(CEI 61076-2-001:2011) (IEC 61076-2-001:2011)
This European Standard was approved by CENELEC on 2011-07-26. CENELEC members are bound to comply
with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard
the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the Central Secretariat or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and notified
to the Central Secretariat has the same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus,
the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy,
Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia,
Spain, Sweden, Switzerland and the United Kingdom.
CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
Management Centre: Avenue Marnix 17, B - 1000 Brussels
© 2011 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 61076-2-001:2011 E
---------------------- Page: 3 ----------------------
SIST EN 61076-2-001:2011
EN 61076-2-001:2011 - 2 -
Foreword
The text of document 48B/2241/FDIS, future edition 2 of IEC 61076-2-001, prepared by SC 48B,
Connectors, of IEC TC 48, Electromechanical components and mechanical structures for electronic
equipment, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as
EN 61076-2-001 on 2011-07-26.
This European Standard supersedes EN 61076-2-001:2001.
EN 61076-2-001:2011 includes the following significant technical changes with respect to
EN 61076-2-001:2001:
a) This European Standard no longer includes the quality assessment procedures. As described in
EN 61076-1 and EN 62197-1, a new document structure has been established. EN 61076-2-001 has
been revised to reflect this updated structure.
b) Subclause 3.2, Systems of levels has been introduced.
c) The subclause IEC type designation has been removed.
d) Clauses 4 Dimensional information and 5 Characteristics have been added.
e) Some clauses and test groups have been rearranged. Test group HP has been added.
EN 61076-2-001:2011 should be used in conjunction with EN 61076-1, EN 61076-2 and EN 62197-1.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN and CENELEC shall not be held responsible for identifying any or all such patent
rights.
The following dates were fixed:
– latest date by which the EN has to be implemented
at national level by publication of an identical
(dop) 2012-04-26
national standard or by endorsement
– latest date by which the national standards conflicting
(dow) 2014-07-26
with the EN have to be withdrawn
Annex ZA has been added by CENELEC.
__________
Endorsement notice
The text of the International Standard IEC 61076-2-001:2011 was approved by CENELEC as a European
Standard without any modification.
In the official version, for Bibliography, the following note has to be added for the standard indicated:
IEC 60664-1 NOTE Harmonized as EN 60664-1.
__________
---------------------- Page: 4 ----------------------
SIST EN 61076-2-001:2011
- 3 - EN 61076-2-001:2011
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
NOTE When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD
applies.
Publication Year Title EN/HD Year
IEC 60068-1 - Environmental testing - EN 60068-1 -
Part 1: General and guidance
IEC 60352 Series Solderless connections EN 60352 Series
IEC 60512 Series Connectors for electronic equipment - Tests EN 60512 Series
and measurements
IEC 60512-1 - Connectors for electronic equipment - Tests EN 60512-1 -
and measurements -
Part 1: General
IEC 60512-1-100 - Connectors for electronic equipment - Tests EN 60512-1-100 -
and measurements -
Part 1-100: General - Applicable publications
IEC 60999-1 - Connecting devices - Electrical copper EN 60999-1 -
conductors - Safety requirements for screw-
type and screwless-type clamping units -
Part 1: General requirements and particular
requirements for clamping units for conductors
from 0,2 mm² up to 35 mm² (included)
IEC 60999-2 - Connecting devices - Electrical copper EN 60999-2 -
conductors - Safety requirements for screw-
type and screwless-type clamping units -
Part 2: Particular requirements for clamping
units for conductors above 35 mm² up to 300
mm² (included)
IEC 61076-1 2006 Connectors for electronic equipment - EN 61076-1 2006
Product requirements -
Part 1: Generic specification
IEC 61076-2 2011 Connectors for electronic equipment - EN 61076-2 2011
Product requirements -
Part 2: Sectional specification for circular
connectors
IEC 62197-1 - Connectors for electronic equipment - Quality EN 62197-1 -
assessment requirements -
Part 1: Generic specification
---------------------- Page: 5 ----------------------
SIST EN 61076-2-001:2011
---------------------- Page: 6 ----------------------
SIST EN 61076-2-001:2011
IEC 61076-2-001
®
Edition 2.0 2011-06
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Connectors for electronic equipment – Product requirements –
Part 2-001: Circular connectors – Blank detail specification
Connecteurs pour équipements électroniques – Exigences de produit –
Partie 2-001: Connecteurs circulaires – Spécification particulière cadre
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
PRICE CODE
INTERNATIONALE
CODE PRIX XC
ICS 31.220.10 ISBN 978-2-88912-561-6
® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale
---------------------- Page: 7 ----------------------
SIST EN 61076-2-001:2011
– 2 – 61076-2-001 IEC:2011
CONTENTS
FOREWORD . 5
INTRODUCTION . 7
1 Scope . 9
2 Normative references . 11
3 Technical information . 13
3.1 Terms and definitions . 13
3.2 Systems of levels . 13
3.2.1 Performance levels . 13
3.2.2 Compatibility levels, according to IEC 61076-1 Ed. 2.0 . 13
3.3 Classification into climatic categories . 13
3.4 Creepage and clearance distances . 15
3.5 Current-carrying capacity . 15
3.6 Marking . 15
4 Dimensional information . 17
4.1 General . 17
4.2 Isometric view and common features . 17
4.2.1 Common features . 19
4.2.2 Reference system . 19
4.3 Engagement (mating) information . 21
4.3.1 Engaging (mating) direction . 21
4.3.2 Perpendicular to the engaging (mating) direction . 21
4.3.3 Inclination . 21
4.4 Fixed connectors . 21
4.4.1 Dimensions . 21
4.4.2 Terminations . 21
4.5 Free connectors . 23
4.5.1 Dimensions . 23
4.5.2 Terminations . 23
4.6 Accessories . 23
4.7 Mounting information for connectors . 23
4.7.1 Mounting on panels . 25
4.8 Gauges . 25
4.8.1 Sizing gauges and retention force gauges . 25
4.8.2 Mechanical function, engaging/separating/insertion/withdrawal force
gauges . 27
4.8.3 Probes . 27
4.8.4 Contact resistance gauge . 27
4.8.5 Test panel (for voltage proof test) . 27
4.8.6 Test panel (for EMC/ crosstalk etc.) . 27
5 Characteristics . 29
5.1 General . 29
5.2 Pin assignment and other definitions . 29
5.3 Classification into climatic categories . 29
5.4 Electrical characteristics . 29
5.4.1 Creepage and clearance distances . 29
5.4.2 Voltage proof . 31
---------------------- Page: 8 ----------------------
SIST EN 61076-2-001:2011
61076-2-001 IEC:2011 – 3 –
5.4.3 Current-carrying capacity. 31
5.4.4 Contact and shield resistance . 31
5.4.5 Insulation resistance . 31
5.4.6 Impedance. 33
5.5 Mechanical characteristics . 35
5.5.1 Mechanical operation . 35
5.5.2 Effectiveness of connector coupling devices . 35
5.5.3 Engaging and separating forces (or insertion and withdrawal forces) . 35
5.5.4 Contact retention in insert . 35
5.5.5 Polarizing and coding method . 35
5.6 Other characteristics . 37
5.6.1 Shock and vibration (method either random or sine) . 37
5.6.2 Degree of protection provided by enclosures (IP code) . 37
5.6.3 Screen and shielding properties . 37
5.7 Environmental aspects . 39
5.7.1 Marking of insulation material (plastics) . 39
5.7.2 Design/ use of material . 39
6 Test schedule . 41
6.1 General . 41
6.1.1 Climatic category . 41
6.1.2 Creepage and clearance distances . 43
6.1.3 Arrangement for contact resistance measurement . 43
6.1.4 Arrangement for dynamic stress tests . 43
6.1.5 Arrangement for testing static load; axial . 43
6.1.6 Wiring of specimens . 43
6.2 Test schedules . 45
6.2.1 Basic (minimum) test schedule . 45
6.2.2 Full test schedule . 49
6.3 Test procedures and measuring methods . 73
6.4 Pre-conditioning . 73
6.5 Wiring and mounting of specimens . 73
6.5.1 Wiring . 73
6.5.2 Mounting . 73
Annex A (normative) New tests and additional test phases . 74
Bibliography . 75
Table 1 – Performance levels . 13
Table 2 – Isometric view and common features . 17
Table 3 – Performance levels, example . 28
Table 4 – Performance levels . 29
Table 5 – Creepage and clearance distances . 29
Table 6 – Performance levels . 41
Table 7 – Creepage and clearance distances . 43
Table 8 – Tests, example . 44
Table 9 – Basic tests . 45
Table 10 – Number of test specimens and contacts . 49
Table 11 – Test group P . 49
---------------------- Page: 9 ----------------------
SIST EN 61076-2-001:2011
– 4 – 61076-2-001 IEC:2011
Table 12 – Test group AP . 53
Table 13 – Test group BP . 59
Table 14 – Test group CP . 63
Table 15 – Test group DP . 65
Table 16 – Test group EP . 67
Table 17 – Test group FP . 67
Table 18 – Test group GP . 69
Table 19 – Test group HP . 69
Table 20 – Test group KP . 71
Table 21 – Test group LP . 71
---------------------- Page: 10 ----------------------
SIST EN 61076-2-001:2011
61076-2-001 IEC:2011 – 5 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
CONNECTORS FOR ELECTRONIC EQUIPMENT –
PRODUCT REQUIREMENTS –
Part 2-001: Circular connectors –
Blank detail specification
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 61076-2-001 has been prepared by subcommittee 48B:
Connectors, of IEC technical committee 48: Electromechanical components and mechanical
structures for electronic equipment.
This International Standard cancels and replaces the first edition of IEC 61076-2-001 (2001).
This edition constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous
edition:
a) This International Standard no longer includes the quality assessment procedures. As
described in IEC 61076-1 and IEC 62197-1, a new document structure has been
established. IEC 61076-2-001 has been revised to reflect this updated structure.
b) Subclause 3.2, Systems of levels has been introduced.
c) The subclause IEC type designation has been removed.
---------------------- Page: 11 ----------------------
SIST EN 61076-2-001:2011
– 6 – 61076-2-001 IEC:2011
d) Clauses 4 Dimensional information and 5 Characteristics have been added.
e) Some clauses and test groups have been rearranged. Test group HP has been added.
The text of this standard is based on the following documents:
FDIS Report on voting
48B/2241/FDIS 48B/2248/RVD
Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.
This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.
A list of all parts of the IEC 61076 series, published under the general title Connectors for
electronic equipment – Product requirements, can be found on the IEC website.
The committee has decided that the contents of this publication will remain unchanged until
the stability date indicated on the IEC web site under "http://webstore.iec.ch" in the data
related to the specific publication. At this date, the publication will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
---------------------- Page: 12 ----------------------
SIST EN 61076-2-001:2011
61076-2-001 IEC:2011 – 7 –
INTRODUCTION
This blank detail product specification is a supplementary document to the sectional product
specification IEC 61076-2 and contains requirements for style, layout and content of detail
product specifications for circular connectors. It should be used in conjunction with the
following publications: IEC 61076-1 and IEC 61076-2 for product requirements as well as
IEC 62197-1 for quality requirements.
The main content of this blank detail product specification is divided into two parts: on one
page the example for a blank detail product specification, on the other page the guidance
notes referring to the example. The guidance notes have the same numbering as the relevant
paragraphs of the example pages.
The sample pages can be used like a template when preparing a detail product specification
within the scope of this document. This document is not intended to replace the templates and
guidance notes of IEC, but to assist in their application. All users are reminded to adhere to
relevant directives and guidelines of the IEC when preparing a standard.
NOTE 1 A detail quality specification IEC 62197-2-1xx should be prepared, based on the blank detail quality
specification for circular connectors IEC 62197-2-001 and its references and should be used in conjunction with the
detail product specification IEC 61076-2-1xx.
NOTE 2 The quality assessment requirements for connectors according to the IEC 61076 series are detailed in
IEC 62197-1.
---------------------- Page: 13 ----------------------
SIST EN 61076-2-001:2011
– 8 – 61076-2-001 IEC:2011
Guidance notes
The following pages give a recommended layout of a detail product specification. The
contents of this page give guidance on the information which should, wherever possible, be
given on the front page of a detail product specification (see IEC Guide 102).
For the scope and definition of a detail product specification, see 1.2.3 of IEC 61076-1.
The numbers between brackets on the front page of the detail product specification
correspond to the following information.
Identification of the detail product specification
[1] The International Electrotechnical Commission or the national standards organization
under whose authority the detail product specification is drafted. It shall also be stated
where the detail product specification may be obtained.
[2] The IEC number of the detail product specification and date of issue.
[3] The IEC number and issue number of the generic and the sectional specifications.
[4] The national number of the detail product specification, if it differs from the IEC number.
Identification of the connector
[5] A short description of the type of connector.
[6] Information on the typical construction of the connector, for example, it should be stated
whether the connector is suitable for mounting on printed boards.
[7] Outline drawing, preferably of isometric or similar projection, from which the connector
may be clearly identified.
[8] Information on performance level(s) and assessment level(s) specified in the document,
if applicable.
[9] Reference data on the most important properties, to allow comparison between the
various connector types.
NOTE It may be convenient to give some of this information in tabular form.
---------------------- Page: 14 ----------------------
SIST EN 61076-2-001:2011
61076-2-001 IEC:2011 – 9 –
[1] IEC
Detail product specification
number
[2]
Generic specification number National number of detail product
specification
Electronic components of assessed quality in accordance with: (it is not necessary to use this if the
IEC number is identical)
[3] [4]
Outline drawing Product description
[5]
[7]
[6]
[8]
Performance level(s):
Asse
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.