oSIST prEN IEC 61084-2-3:2023

Cable trunking systems and cable ducting systems for electrical installations - Part 2-3: Particular requirements - Slotted cable trunking systems intended for installation in cabinets

This part 2-3 of the EN IEC 61084 series specifies particular requirements and tests slotted cable
trunking systems intended for mounting inside cabinets in electrical and/or communication system installations.

Elektroinstallationskanalsysteme für elektrische Installationen - Teil 2-3: Besondere Anforderungen an Verdrahtungskanäle zum Einbau in Schaltschränke

Systèmes de goulottes et systèmes de conduits-profilés pour installations électriques - Partie 2-3: Exigences particulières - Systèmes de goulottes de câblage pour installation dans les armoires

L'IEC 61084-2-3:2017 spécifie les exigences et les essais pour les systèmes de goulottes (SG) et les systèmes de conduits-profilés (SCP) destinés au logement de conducteurs isolés, câbles et éventuels autres équipements électriques et, si nécessaire, à leur séparation de protection électrique, dans des installations électriques et/ou de systèmes de communication. La tension maximale de ces installations est de 1 000 V en courant alternatif et 1 500 V en courant continu.
Les systèmes de goulottes de câblage sont prévus pour être montés à l’intérieur d’armoires dans des installations électriques et/ou de systèmes de communication.
Le présent document ne s’applique pas aux systèmes de conduits, systèmes de chemins de câble, systèmes d’échelles à câble, systèmes de canalisations préfabriquées ou aux équipements couverts par d’autres normes.
Cette Norme internationale doit être utilisée conjointement avec l’IEC 61084-1:2017.

Sistemi kabelskih korit in sistemi kabelskih cevi za električne inštalacije - 2-3. del: Posebne zahteve - Utorski sistemi kabelskih korit za inštalacije v priključnih omaricah

General Information

• Status: Not Published
• Public Enquiry End Date: 28-Feb-2023
• ICS: 29.060.01 - Electrical wires and cables in general
• ICS: 29.120.10 - Conduits for electrical purposes
• Technical Committee: I11 - Imaginarni 11
• Current Stage: 4020 - Public enquire (PE) (Adopted Project)
• Start Date: 14-Dec-2022
• Due Date: 03-May-2023
• Completion Date: 11-May-2023
• Directive: 2014/35/EU - Directive 2014/35/EU of the European Parliament and of the Council of 26 February 2014 on the harmonisation of the laws of the Member States relating to the making available on the market of electrical equipment designed for use within certain voltage limits
• Mandate: M/511 - Mandate to CEN, CENELEC and ETSI relating to harmonised standards in the field of the Low Voltage Directive
• Ref Project: FprEN IEC 61084-2-3:2023 - Cable trunking systems and cable ducting systems for electrical installations - Part 2-3: Particular requirements - Slotted cable trunking systems intended for installation in cabinets

Relations

• Revised: SIST EN 50085-2-3:2010 - Cable trunking systems and cable ducting systems for electrical installations - Part 2-3: Particular requirements for slotted cable trunking systems intended for installation in cabinets
• Effective Date: 09-Jun-2020
• Amended By: oSIST prEN IEC 61084-2-3:2023/oprAA:2023 - Cable trunking systems and cable ducting systems for electrical installations - Part 2-3: Particular requirements - Slotted cable trunking systems intended for installation in cabinets
• Effective Date: 09-Jun-2020

Standards Content (Sample)

SLOVENSKI STANDARD
oSIST prEN IEC 61084-2-3:2023
01-februar-2023
Sistemi kabelskih korit in sistemi kabelskih cevi za električne inštalacije - 2-3. del:
Posebne zahteve - Utorski sistemi kabelskih korit za inštalacije v priključnih
omaricah
Cable trunking systems and cable ducting systems for electrical installations - Part 2-3:
Particular requirements - Slotted cable trunking systems intended for installation in
cabinets
Elektroinstallationskanalsysteme für elektrische Installationen - Teil 2-3: Besondere
Anforderungen an Verdrahtungskanäle zum Einbau in Schaltschränke
Systèmes de goulottes et systèmes de conduits-profilés pour installations électriques -
Partie 2-3: Exigences particulières - Systèmes de goulottes de câblage pour installation
dans les armoires
Ta slovenski standard je istoveten z: prEN IEC 61084-2-3:2022
ICS:
29.120.10 Inštalacijske cevi za Conduits for electrical
električne namene purposes
oSIST prEN IEC 61084-2-3:2023 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN IEC 61084-2-3:2023

---------------------- Page: 2 ----------------------
oSIST prEN IEC 61084-2-3:2023


EUROPEAN STANDARD DRAFT
prEN IEC 61084-2-3
NORME EUROPÉENNE

EUROPÄISCHE NORM

December 2022
ICS 29.060.01; 29.120.10 Will supersede EN 50085-2-3:2010
English Version
Cable trunking systems and cable ducting systems for electrical
installations - Part 2-3: Particular requirements - Slotted cable
trunking systems intended for installation in cabinets
(IEC 61084-2-3:2017)
Systèmes de goulottes et systèmes de conduits-profilés Elektroinstallationskanalsysteme für elektrische
pour installations électriques - Partie 2-3: Exigences Installationen - Teil 2-3: Besondere Anforderungen an
particulières - Systèmes de goulottes de câblage pour Verdrahtungskanäle zum Einbau in Schaltschränke
installation dans les armoires (IEC 61084-2-3:2017)
(IEC 61084-2-3:2017)
This draft European Standard is submitted to CENELEC members for enquiry.
Deadline for CENELEC: 2023-03-03.

The text of this draft consists of the text of IEC 61084-2-3:2017.

If this draft becomes a European Standard, CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which
stipulate the conditions for giving this European Standard the status of a national standard without any alteration.

This draft European Standard was established by CENELEC in three official versions (English, French, German).
A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to
the CEN-CENELEC Management Centre has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Türkiye and the United Kingdom.

Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to
provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.


European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2022 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Project: 72102 Ref. No. prEN IEC 61084-2-3:2022 E

---------------------- Page: 3 ----------------------
oSIST prEN IEC 61084-2-3:2023
prEN IEC 61084-2-3:2022 (E)
European foreword
This document (prEN IEC 61084-2-3:2022) consists of the text of document IEC 61084-2-3:2017,
prepared by SC 23A "Cable management systems" of IEC/TC 23 "Electrical accessories".
This document is currently submitted to the Enquiry.
The following dates are proposed:
• latest date by which the existence of this document (doa) dor + 6 months
has to be announced at national level
• latest date by which this document has to be (dop) dor + 12 months
implemented at national level by publication of an
identical national standard or by endorsement
• latest date by which the national standards (dow) dor + 60 months
conflicting with this document have to be withdrawn (to be confirmed or
modified when voting)
This document will supersede EN 50085-2-3:2010 and all of its amendments and corrigenda (if any).
This document has been prepared under a Standardization Request given to CENELEC by the
European Commission and the European Free Trade Association, and supports essential requirements
of EU Directive(s) / Regulation(s).
For relationship with EU Directive(s) / Regulation(s), see informative Annex ZZ, which is an integral part
of prEN IEC 61084-2-3:2022/prAA:2022.


2

---------------------- Page: 4 ----------------------
oSIST prEN IEC 61084-2-3:2023



IEC 61084-2-3

®


Edition 1.0 2017-03




INTERNATIONAL



STANDARD




NORME



INTERNATIONALE











Cable trunking systems and cable ducting systems for electrical installations –

Part 2-3: Particular requirements – Slotted cable trunking systems intended for

installation in cabinets




Systèmes de goulottes et systèmes de conduits-profilés pour installations

électriques –


Partie 2-3: Exigences particulières – Systèmes de goulottes de câblage pour

installation dans les armoires












INTERNATIONAL

ELECTROTECHNICAL

COMMISSION


COMMISSION

ELECTROTECHNIQUE


INTERNATIONALE




ICS 29.060.01; 29.120.10 ISBN 978-2-8322-4120-2



Warning! Make sure that you obtained this publication from an authorized distributor.

Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agréé.

® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale

---------------------- Page: 5 ----------------------
oSIST prEN IEC 61084-2-3:2023
– 2 – IEC 61084-2-3:2017  IEC 2017
CONTENTS
FOREWORD . 3
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 5
4 General requirements . 6
5 General conditions for tests . 6
6 Classification . 7
7 Marking and documentation . 7
8 Dimensions. 7
9 Construction . 8
10 Mechanical properties. 8
11 Electrical properties . 10
12 Thermal properties . 10
13 Fire hazard . 10
14 External influences . 11
15 Electromagnetic compatibility . 11
Annex A (informative) Types of cable trunking systems (CTS) and cable ducting
systems (CDS) . 17
Bibliography . 18

Figure 101 – Examples of pattern of fixing holes in the base of the slotted trunking
length . 12
Figure 102 – Examples of sizes for the fixing holes . 13
Figure 103 – Fixing distances for cable support test . 14
Figure 104 – Arrangements for cable support test . 15
Figure 105 – Arrangement for flame test . 16

---------------------- Page: 6 ----------------------
oSIST prEN IEC 61084-2-3:2023
IEC 61084-2-3:2017  IEC 2017 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________

CABLE TRUNKING SYSTEMS AND CABLE DUCTING
SYSTEMS FOR ELECTRICAL INSTALLATIONS –

Part 2-3: Particular requirements – Slotted cable
trunking systems intended for installation in cabinets

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 61084-2-3 has been prepared by subcommittee 23A: Cable
management systems, of IEC technical committee 23: Electrical accessories.
This International standard is to be used in conjunction with IEC 61084-1:2017.
The text of this standard is based on the following documents:
FDIS Report on voting
23A/829/FDIS 23A/835/RVD

Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.

---------------------- Page: 7 ----------------------
oSIST prEN IEC 61084-2-3:2023
– 4 – IEC 61084-2-3:2017  IEC 2017
This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.
This Part of the IEC 61084 series supplements or modifies the corresponding clauses of
IEC 61084-1:2017 as follows:
– where no particular clause or subclause of IEC 61084-1 is mentioned, the corresponding
clause or subclause applies as far as it is reasonable;
– where "addition", "modification" or “replacement” is stated, the relevant text of
IEC 61084-11 is to be adapted accordingly;
– subclauses, figures and tables which are additional to those in IEC 61084-1 are numbered
starting from 101.
In this standard, the following print types are used:
– requirements and definitions: roman type;
– compliance statements: italic type.
A list of all parts in the IEC 61084 series, published under the general title Cable trunking and
cable ducting systems for electrical installations, can be found on the IEC website.
The committee has decided that the contents of this publication will remain unchanged until
the stability date indicated on the IEC website under "http://webstore.iec.ch" in the data
related to the specific publication. At this date, the publication will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.

---------------------- Page: 8 ----------------------
oSIST prEN IEC 61084-2-3:2023
IEC 61084-2-3:2017  IEC 2017 – 5 –
CABLE TRUNKING SYSTEMS AND CABLE DUCTING
SYSTEMS FOR ELECTRICAL INSTALLATIONS –

Part 2-3: Particular requirements – Slotted cable
trunking systems intended for installation in cabinets



1 Scope
This part of the IEC 61084 series specifies requirements and tests for cable trunking systems
(CTS) and cable ducting systems (CDS) intended for the accommod
...