SIST EN 303 979 V1.1.1:2015
Satellite Earth Stations and Systems (SES); Harmonized EN for Earth Stations on Mobile Platforms (ESOMP) transmitting towards satellites in non-geostationary orbit in the 27,5 GHz to 29,1 GHz and 29,5 GHz to 30,0 GHz frequency bands covering the essential requirements of article 3.2 of the R&TTE Directive
Satellite Earth Stations and Systems (SES); Harmonized EN for Earth Stations on Mobile Platforms (ESOMP) transmitting towards satellites in non-geostationary orbit in the 27,5 GHz to 29,1 GHz and 29,5 GHz to 30,0 GHz frequency bands covering the essential requirements of article 3.2 of the R&TTE Directive
The present document applies to Earth Stations on Mobile Platforms (ESOMP), which have the following characteristics.
• The ESOMP is designed for both mobile and stationary operation.
• The ESOMP operates on various mobile platforms such as trains, maritime vessels, aircraft and other vehicles and, therefore, may be subject to occasional disturbances and interruptions in the satellite link.
• The ESOMP is operating as part of a satellite network (e.g. star, mesh or point-to-point) used for the distribution and/or exchange of information.
• The ESOMP is comprised of all the equipment, electrical and mechanical, from the antenna itself to the interface with other communications equipment on a mobile platform (usually referred to as the terrestrial interface).
• The ESOMP comprises of one or more emitters and the system overview given in figure 1 should be interpreted accordingly.
• The ESOMP transmits within the frequency range from 27,5 GHz to 29,1 GHz and 29,5 GHz to 30,0 GHz, which is a band allocated to the Fixed Satellite Services (FSS) (Earth-to-space) among other services. National regulations will specify the bands available for the operation of the ESOMP. Such regulations may designate some parts of the frequency range 27,5 GHz to 29,1 GHz to terrestrial services such as the Fixed Service.
However, the operation of the ESOMP may be permitted under national regulations in the 29,50 GHz to 30,00 GHz band since this band is allocated on a primary basis to the Fixed-Satellite Service.
• The ESOMP receives in one or more frequencies within the range from 17,30 GHz to 20,20 GHz (FSS).
• The ESOMP uses linear or circular polarization.
• The ESOMP operates through non-geostationary satellites.
• The ESOMP is designed for unattended operation.
• The ESOMP is controlled and monitored by a Network Control Facility (NCF). This function may be performed centrally (e.g. for a network of ESOMPs with a central hub) or it could be performed within the ESOMP for autonomous control. The NCF is outside the scope of the present document.
• The ESOMP operating in the 27,5 GHz to 28,6 GHz and 29,5 GHz to 30 GHz bands: epfd limits given in Article 22 of the ITU Radio Regulations [i.6] apply for the ESOMPs operating with the NGSO system for the protection of the GSO networks (see No 22.5D of the ITU RR).
• ESOMP operating in the 28,6 GHz to 29,1 GHz band: No 9.11A of the ITU RR applies to the NGSO network of the ESOMP, meaning that the NGSO will be required to coordinate with earlier filed GSO networks or NGSO systems (See No. 5.523A of the ITU RR).
The present document applies to the ESOMP with its ancillary equipment and its various telecommunication ports, and when operated within the boundary limits of the operational environmental profile as declared by the applicant and when installed as required by the applicant's declaration or in the user documentation. The present document is intended to cover the provisions of Directive 1999/5/EC [i.2] (R&TTE Directive) article 3.2, which states that "… radio equipment shall be so constructed that it effectively uses the spectrum allocated to terrestrial/space radio communications and orbital resources so as to avoid harmful interference".
NOTE 1: Operational requirements are defined by national administrations and by relevant ECC Decisions. In addition to the present document, other ENs that specify technical requirements in respect of essential requirements under other parts of Article 3 of the Directive 1999/5/EC [i.2] (R&TTE Directive) may apply to equipment within the scope of the present document.
NOTE 2: A list of such ENs is included on the web site http://www.newapproach.org/.
Satellite Earth Stations and Systems (SES) - Harmonized EN for Earth Stations on Mobile Platforms (ESOMP) transmitting towards satellites in geostationary orbit in the 27,5 GHz to 30,0 GHz frequency bands covering the essential requirements of article 3.2 of the R&TTE Directive
Satelitske zemeljske postaje in sistemi (SES) - Harmonizirani EN za zemeljske postaje na mobilnih platformah (ESOMP), ki oddajajo proti satelitom v negeostacionarni orbiti v pasovih od 27,5 GHz do 29,1 GHz in od 29,5 GHz do 30,0 GHz, ki zajema bistvene zahteve člena 3.2 direktive R&TTE
Ta dokument se uporablja za zemeljske postaje na mobilnih platformah (ESOMP) z naslednjimi značilnostmi.
• Zemeljska postaja na mobilni platformi je izdelana za mobilno in stacionarno delovanje.
• Zemeljska postaja na mobilni platformi deluje na različnih mobilnih platformah, npr. na vlakih, morskih plovilih, letalih in drugih vozilih, pri čemer lahko pride do občasnih motenj in prekinitev v satelitski povezavi.
• Zemeljska postaja na mobilni platformi deluje kot del satelitskega omrežja (npr. zvezdnega, mrežnega ali od točke do točke), ki se uporablja za distribucijo in/ali izmenjavo informacij.
• Zemeljska postaja na mobilni platformi je sestavljena iz vse opreme, električne in mehanske, od same antene do vmesnikov z drugo komunikacijsko opremo na mobilni platformi (običajno se imenujejo zemeljski vmesniki).
• Zemeljska postaja na mobilni platformi je sestavljena iz enega ali več oddajnikov, pri čemer naj bi se pregled sistema na sliki 1 razlagal v skladu s tem.
• Zemeljska postaja na mobilni platformi oddaja na frekvenci od 27,5 GHz do 29,1 GHz in od 29,5 GHz do 30,0 GHz – to je pas, ki je med drugimi storitvami dodeljen fiksnim satelitskim storitvam (FSS) (zemlja–vesolje). V okviru nacionalnih predpisov bodo opredeljeni pasovi, ki so na voljo za delovanje zemeljske postaje na mobilni platformi. V okviru teh predpisov se lahko nekateri deli frekvenčnega razpona 27,5 GHz do 29,1 GHz dodelijo zemeljskim storitvam, kot je fiksna storitev.
Vendar se lahko delovanje zemeljske postaje na mobilni platformi dovoli v skladu z nacionalnimi predpisi v pasu od 29,5 GHz do 30,0 GHz, ker je ta pas primarno dodeljen fiksni satelitski storitvi.
• Zemeljska postaja na mobilni platformi sprejema v eni ali več frekvencah v obsegu od 17,30 GHz do 20,20 GHz (fiksne satelitske storitve).
• Zemeljska postaja na mobilni platformi uporablja linearno ali krožno polarizacijo.
• Zemeljska postaja na mobilni platformi deluje prek negeostacionarnih satelitov.
• Zemeljska postaja na mobilni platformi je izdelana za nenadzorovano delovanje.
•Zemeljska postaja na mobilni platformi se krmili in spremlja z napravo za krmiljenje omrežja (NCF). Ta funkcija se lahko izvaja centralno (npr. za omrežje zemeljskih postaj na mobilni platformi s centralnim vozliščem) ali pa se lahko izvaja v sami zemeljski postaji na mobilni platformi za avtonomno krmiljenje. Naprava za krmiljenje omrežja ne spada v področje uporabe tega dokumenta.
• Zemeljska postaja na mobilni platformi, ki deluje v pasovih 27,5 GHz do 28,6 GHz in 29,5 GHz do 30 GHz: mejne vrednosti EPFD iz člena 22 Pravilnika o radiokomunikacijah Mednarodne telekomunikacijske zveze [i.6] se uporabljajo za zemeljske postaje na mobilni platformi, ki delujejo s sistemom v negeostacionarni orbiti za zaščito omrežij v geostacionarni orbiti (glej št. 22.5D Pravilnika o radiokomunikacijah Mednarodne telekomunikacijske zveze).
• Zemeljska postaja na mobilni platformi, ki deluje v pasu 28,6 GHz do 29,1 GHz: št. 9.11A Pravilnika o radiokomunikacijah Mednarodne telekomunikacijske zveze se nanaša na omrežje v negeostacionarni orbiti zemeljske postaje na mobilni platformi, kar pomeni, da se mora negeostacionarna orbita usklajevati s prej prijavljenimi omrežji v geostacionarni orbiti ali sistemi v negeostacionarni orbiti) (glej št. 5.523A Pravilnika o radiokomunikacijah Mednarodne telekomunikacijske zveze).
General Information
Buy Standard
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Satellite Earth Stations and Systems (SES) - Harmonized EN for Earth Stations on Mobile Platforms (ESOMP) transmitting towards satellites in geostationary orbit in the 27,5 GHz to 30,0 GHz frequency bands covering the essential requirements of article 3.2 of the R&TTE DirectiveSatellite Earth Stations and Systems (SES); Harmonized EN for Earth Stations on Mobile Platforms (ESOMP) transmitting towards satellites in non-geostationary orbit in the 27,5 GHz to 29,1 GHz and 29,5 GHz to 30,0 GHz frequency bands covering the essential requirements of article 3.2 of the R&TTE Directive33.060.30Radiorelejni in fiksni satelitski komunikacijski sistemiRadio relay and fixed satellite communications systemsICS:Ta slovenski standard je istoveten z:EN 303 979 V1.1.1SIST EN 303 979 V1.1.1:2015en,fr,de01-oktober-2015SIST EN 303 979 V1.1.1:2015SLOVENSKI
STANDARD
SIST EN 303 979 V1.1.1:2015
ETSI EN 303 979 V1.1.1 (2015-07) Satellite Earth Stations and Systems (SES); Harmonised EN for Earth Stations on Mobile Platforms (ESOMP) transmitting towards satellites in non-geostationary orbit in the 27,5 GHz to 29,1 GHz and 29,5 GHz to 30,0 GHz frequency bands covering the essential requirements of article 3.2 of the R&TTE Directive
HARMONISED EUROPEAN STANDARD SIST EN 303 979 V1.1.1:2015
ETSI ETSI EN 303 979 V1.1.1 (2015-07) 2
Reference DEN/SES-00364 Keywords antenna, earth station, mobile, non-GSO, regulation, satellite ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00
Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C Association à but non lucratif enregistrée à la Sous-Préfecture de Grasse (06) N° 7803/88
Important notice The present document can be downloaded from: http://www.etsi.org/standards-search The present document may be made available in electronic versions and/or in print. The content of any electronic and/or print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at http://portal.etsi.org/tb/status/status.asp If you find errors in the present document, please send your comment to one of the following services: https://portal.etsi.org/People/CommiteeSupportStaff.aspx Copyright Notification No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm except as authorized by written permission of ETSI. The content of the PDF version shall not be modified without the written authorization of ETSI. The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2015. All rights reserved.
DECTTM, PLUGTESTSTM, UMTSTM and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members. 3GPPTM and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association. SIST EN 303 979 V1.1.1:2015
ETSI ETSI EN 303 979 V1.1.1 (2015-07) 3 Contents Intellectual Property Rights . 7 Foreword . 7 Modal verbs terminology . 7 Introduction . 7 1 Scope . 9 2 References . 10 2.1 Normative references . 10 2.2 Informative references . 11 3 Definitions, symbols and abbreviations . 11 3.1 Definitions . 11 3.2 Symbols . 13 3.3 Abbreviations . 13 4 Technical requirements specifications . 14 4.1 General . 14 4.1.1 Environmental profile . 14 4.1.2 Operational configurations . 14 4.1.3 Determination of geographic location of the ESOMP . 14 4.1.4 EIRPAggregate for networks of ESOMPs . 15 4.1.5 Presentation of equipment for testing purposes . 15 4.1.6 Choice of model for testing . 15 4.1.7 Mechanical and electrical design . 15 4.1.7.1 General . 15 4.1.7.2 Marking (equipment identification) . 15 4.1.7.3 Equipment identification . 15 4.2 Conformance requirements . 16 4.2.1 Off-axis spurious radiation . 16 4.2.1.1 Justification . 16 4.2.1.2 Specification. 16 4.2.1.3 Conformance tests . 17 4.2.2 On-axis spurious radiation . 17 4.2.2.1 Justification . 17 4.2.2.2 Specification. 17 4.2.2.2.1 "Carrier-on" radio state . 17 4.2.2.2.2 "Carrier-off" and "Emissions disabled" radio states . 17 4.2.2.3 Conformance tests . 17 4.2.3 epfd Limits . 18 4.2.3.1 Justification . 18 4.2.3.2 Specification. 18 4.2.3.3 Conformance tests . 18 4.2.4 Uplink Power Control Specification . 18 4.2.5 Carrier suppression . 18 4.2.5.1 Justification . 18 4.2.5.2 Specification. 18 4.2.5.3 Conformance tests . 18 4.2.6 Antenna pointing and polarization alignment . 18 4.2.6.1 Antenna pointing accuracy . 18 4.2.6.1.1 Purpose . 18 4.2.6.1.2 Pointing accuracy specification . 18 4.2.6.1.3 On-axis cross polarization isolation specification . 19 4.2.6.1.4 Conformance tests . 19 4.2.6.2 Antenna Pointing Error Detection . 19 4.2.6.2.1 Purpose . 19 4.2.6.2.2 Pointing error detection specification . 19 SIST EN 303 979 V1.1.1:2015
ETSI ETSI EN 303 979 V1.1.1 (2015-07) 4 4.2.6.2.3 Polarization angle alignment specification . 19 4.2.6.2.4 Conformance tests . 20 4.2.7 Cessation of emissions . 20 4.2.7.1 Justification . 20 4.2.7.2 Specification. 20 4.2.7.2.1 Specification 1: Mode of cessation of emissions . 20 4.2.7.2.2 Specification 2: Conditions under which the ESOMP shall cease emissions . 20 4.2.7.2.3 Specification 3: Cessation of emissions . 21 4.2.7.2.4 Specification 4: Fault conditions . 21 4.2.7.3 Conformance tests . 21 4.2.8 Identification of the ESOMP . 21 4.2.8.1 Justification . 21 4.2.8.2 Specification. 21 4.2.8.3 Conformance tests . 21 4.2.9 Control and Monitoring Functions (CMFs) . 22 4.2.9.1 ESOMP States . 22 4.2.9.1.1 General . 22 4.2.9.1.2 CMF state diagram . 23 4.2.9.2 Processor monitoring . 24 4.2.9.2.1 Justification . 24 4.2.9.2.2 Specification . 24 4.2.9.2.3 Conformance tests . 24 4.2.9.3 Transmit subsystem monitoring . 25 4.2.9.3.1 Justification . 25 4.2.9.3.2 Specification . 25 4.2.9.3.3 Conformance tests . 25 4.2.9.4 Power-on/Reset . 25 4.2.9.4.1 Justification . 25 4.2.9.4.2 Specification . 25 4.2.9.4.3 Conformance tests . 25 4.2.9.5 Control Channel (CC) and Response Channel (RC) . 25 4.2.9.5.1 Justification . 25 4.2.9.5.2 Specification . 25 4.2.9.5.3 Conformance tests . 26 4.2.9.6 Network control commands . 26 4.2.9.6.1 Justification . 26 4.2.9.6.2 Specification . 26 4.2.9.6.3 Conformance tests . 27 4.2.9.7 Initial burst transmission . 27 4.2.9.7.1 Justification . 27 4.2.9.7.2 Specification . 27 4.2.9.7.3 Conformance tests . 27 4.2.9.8 Inhibition of transmissions . 27 4.2.9.8.1 Justification . 27 4.2.9.8.2 Specification . 27 4.2.9.8.3 Conformance tests . 27 5 Testing for compliance with technical requirements . 28 5.1 Environmental conditions for testing . 28 5.2 Essential radio test suites . 28 6 Test methods for all aspects of the ESOMP . 28 6.1 General . 28 6.1.1 General requirements . 28 6.1.2 Interpretation of measurement results . 28 6.1.3 Measuring receiver . 29 6.2 Off-axis spurious radiation . 30 6.2.1 General . 30 6.2.2 Test method . 30 6.2.2.1 General . 30 6.2.2.2 Multi-carrier operation . 31 6.2.3 Measurements up to 1 000 MHz . 31 SIST EN 303 979 V1.1.1:2015
ETSI ETSI EN 303 979 V1.1.1 (2015-07) 5 6.2.3.1 Test site . 31 6.2.3.2 Measuring receivers . 31 6.2.3.3 Procedure . 31 6.2.4 Measurements above 1 000 MHz . 32 6.2.4.1 General . 32 6.2.4.2 Identification of the significant frequencies of spurious radiation . 32 6.2.4.2.1 Test site. 32 6.2.4.2.2 Procedure . 32 6.2.4.3 Measurement of radiated power levels of identified spurious radiation . 32 6.2.4.3.1 Test site. 32 6.2.4.3.2 Procedure . 33 6.2.4.4 Measurement of conducted spurious radiation at the antenna flange . 34 6.2.4.4.1 Test site. 34 6.2.4.4.2 Procedure . 34 6.3 On-axis spurious radiation . 35 6.3.1 Test method . 35 6.3.1.1 General . 35 6.3.1.2 Test site . 35 6.3.1.3 Method of measurement . 35 6.3.1.3.1 General . 35 6.3.1.3.2 Method of measurement at the antenna flange . 35 6.3.1.3.3 Method of measurement for an EUT with antenna . 37 6.4 epfd limits . 38 6.5 Carrier suppression . 38 6.5.1 Test method . 38 6.6 Antenna pointing . 38 6.6.1 General . 38 6.6.2 Test method . 38 6.7 Polarization angle alignment capability . 39 6.7.1 General . 39 6.7.2 Test method . 39 6.8 Cessation of emissions of the ESOMP . 39 6.8.1 General . 39 6.8.2 Test Method . 39 6.8.2.1 Required documentation . 39 6.8.2.2 Cessation of emissions from the "Transmission enabled" state . 39 6.8.2.3 Cessation of emission from the "Transmission disabled" state . 40 6.8.2.4 Cessation of emission from the "Initial Phase" state . 40 6.8.2.4.1 EUTs transmitting initial bursts . 40 6.8.2.4.2 EUTs not transmitting initial bursts . 40 6.8.2.5 "Single action" means of cessation of emissions. 41 6.8.2.6 Fault conditions . 41 6.9 Identification of ESOMP . 42 6.9.1 Test arrangement . 42 6.9.2 Test method . 42 6.10 Control and monitoring functions . 42 6.10.1 General . 42 6.10.2 Test arrangement . 42 6.10.3 Processor monitoring- Test method . 42 6.10.4 Transmit subsystem monitoring-Test method . 42 6.10.5 Power-on/Reset-Test method . 43 6.10.6 Control Channel and Response Channel -Test method . 43 6.10.7 Network Control commands-Test method . 44 6.10.8 Initial burst transmission-Test method . 45 6.10.9 Inhibition of tra
...
ETSI EN 303 979 V1.1.1 (2015-07)
HARMONISED EUROPEAN STANDARD
Satellite Earth Stations and Systems (SES);
Harmonised EN for Earth Stations on
Mobile Platforms (ESOMP) transmitting towards
satellites in non-geostationary
orbit in the 27,5 GHz to 29,1 GHz and 29,5 GHz to 30,0 GHz
frequency bands covering the essential requirements
of article 3.2 of the R&TTE Directive
---------------------- Page: 1 ----------------------
2 ETSI EN 303 979 V1.1.1 (2015-07)
Reference
DEN/SES-00364
Keywords
antenna, earth station, mobile, non-GSO,
regulation, satellite
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2015.
All rights reserved.
TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.
TM
3GPP and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI
---------------------- Page: 2 ----------------------
3 ETSI EN 303 979 V1.1.1 (2015-07)
Contents
Intellectual Property Rights . 7
Foreword . 7
Modal verbs terminology . 7
Introduction . 7
1 Scope . 9
2 References . 10
2.1 Normative references . 10
2.2 Informative references . 11
3 Definitions, symbols and abbreviations . 11
3.1 Definitions . 11
3.2 Symbols . 13
3.3 Abbreviations . 13
4 Technical requirements specifications . 14
4.1 General . 14
4.1.1 Environmental profile . 14
4.1.2 Operational configurations . 14
4.1.3 Determination of geographic location of the ESOMP . 14
4.1.4 EIRP for networks of ESOMPs . 15
Aggregate
4.1.5 Presentation of equipment for testing purposes . 15
4.1.6 Choice of model for testing . 15
4.1.7 Mechanical and electrical design . 15
4.1.7.1 General . 15
4.1.7.2 Marking (equipment identification) . 15
4.1.7.3 Equipment identification . 15
4.2 Conformance requirements . 16
4.2.1 Off-axis spurious radiation . 16
4.2.1.1 Justification . 16
4.2.1.2 Specification. 16
4.2.1.3 Conformance tests . 17
4.2.2 On-axis spurious radiation . 17
4.2.2.1 Justification . 17
4.2.2.2 Specification. 17
4.2.2.2.1 "Carrier-on" radio state . 17
4.2.2.2.2 "Carrier-off" and "Emissions disabled" radio states . 17
4.2.2.3 Conformance tests . 17
4.2.3 epfd Limits . 18
4.2.3.1 Justification . 18
4.2.3.2 Specification. 18
4.2.3.3 Conformance tests . 18
4.2.4 Uplink Power Control Specification . 18
4.2.5 Carrier suppression . 18
4.2.5.1 Justification . 18
4.2.5.2 Specification. 18
4.2.5.3 Conformance tests . 18
4.2.6 Antenna pointing and polarization alignment . 18
4.2.6.1 Antenna pointing accuracy . 18
4.2.6.1.1 Purpose . 18
4.2.6.1.2 Pointing accuracy specification . 18
4.2.6.1.3 On-axis cross polarization isolation specification . 19
4.2.6.1.4 Conformance tests . 19
4.2.6.2 Antenna Pointing Error Detection . 19
4.2.6.2.1 Purpose . 19
4.2.6.2.2 Pointing error detection specification . 19
ETSI
---------------------- Page: 3 ----------------------
4 ETSI EN 303 979 V1.1.1 (2015-07)
4.2.6.2.3 Polarization angle alignment specification . 19
4.2.6.2.4 Conformance tests . 20
4.2.7 Cessation of emissions . 20
4.2.7.1 Justification . 20
4.2.7.2 Specification. 20
4.2.7.2.1 Specification 1: Mode of cessation of emissions . 20
4.2.7.2.2 Specification 2: Conditions under which the ESOMP shall cease emissions . 20
4.2.7.2.3 Specification 3: Cessation of emissions . 21
4.2.7.2.4 Specification 4: Fault conditions . 21
4.2.7.3 Conformance tests . 21
4.2.8 Identification of the ESOMP . 21
4.2.8.1 Justification . 21
4.2.8.2 Specification. 21
4.2.8.3 Conformance tests . 21
4.2.9 Control and Monitoring Functions (CMFs) . 22
4.2.9.1 ESOMP States . 22
4.2.9.1.1 General . 22
4.2.9.1.2 CMF state diagram . 23
4.2.9.2 Processor monitoring . 24
4.2.9.2.1 Justification . 24
4.2.9.2.2 Specification . 24
4.2.9.2.3 Conformance tests . 24
4.2.9.3 Transmit subsystem monitoring . 25
4.2.9.3.1 Justification . 25
4.2.9.3.2 Specification . 25
4.2.9.3.3 Conformance tests . 25
4.2.9.4 Power-on/Reset . 25
4.2.9.4.1 Justification . 25
4.2.9.4.2 Specification . 25
4.2.9.4.3 Conformance tests . 25
4.2.9.5 Control Channel (CC) and Response Channel (RC) . 25
4.2.9.5.1 Justification . 25
4.2.9.5.2 Specification . 25
4.2.9.5.3 Conformance tests . 26
4.2.9.6 Network control commands . 26
4.2.9.6.1 Justification . 26
4.2.9.6.2 Specification . 26
4.2.9.6.3 Conformance tests . 27
4.2.9.7 Initial burst transmission . 27
4.2.9.7.1 Justification . 27
4.2.9.7.2 Specification . 27
4.2.9.7.3 Conformance tests . 27
4.2.9.8 Inhibition of transmissions . 27
4.2.9.8.1 Justification . 27
4.2.9.8.2 Specification . 27
4.2.9.8.3 Conformance tests . 27
5 Testing for compliance with technical requirements . 28
5.1 Environmental conditions for testing . 28
5.2 Essential radio test suites . 28
6 Test methods for all aspects of the ESOMP . 28
6.1 General . 28
6.1.1 General requirements . 28
6.1.2 Interpretation of measurement results . 28
6.1.3 Measuring receiver . 29
6.2 Off-axis spurious radiation . 30
6.2.1 General . 30
6.2.2 Test method . 30
6.2.2.1 General . 30
6.2.2.2 Multi-carrier operation . 31
6.2.3 Measurements up to 1 000 MHz . 31
ETSI
---------------------- Page: 4 ----------------------
5 ETSI EN 303 979 V1.1.1 (2015-07)
6.2.3.1 Test site . 31
6.2.3.2 Measuring receivers . 31
6.2.3.3 Procedure . 31
6.2.4 Measurements above 1 000 MHz . 32
6.2.4.1 General . 32
6.2.4.2 Identification of the significant frequencies of spurious radiation . 32
6.2.4.2.1 Test site. 32
6.2.4.2.2 Procedure . 32
6.2.4.3 Measurement of radiated power levels of identified spurious radiation . 32
6.2.4.3.1 Test site. 32
6.2.4.3.2 Procedure . 33
6.2.4.4 Measurement of conducted spurious radiation at the antenna flange . 34
6.2.4.4.1 Test site. 34
6.2.4.4.2 Procedure . 34
6.3 On-axis spurious radiation . 35
6.3.1 Test method . 35
6.3.1.1 General . 35
6.3.1.2 Test site . 35
6.3.1.3 Method of measurement . 35
6.3.1.3.1 General . 35
6.3.1.3.2 Method of measurement at the antenna flange . 35
6.3.1.3.3 Method of measurement for an EUT with antenna . 37
6.4 epfd limits . 38
6.5 Carrier suppression . 38
6.5.1 Test method . 38
6.6 Antenna pointing . 38
6.6.1 General . 38
6.6.2 Test method . 38
6.7 Polarization angle alignment capability . 39
6.7.1 General . 39
6.7.2 Test method . 39
6.8 Cessation of emissions of the ESOMP . 39
6.8.1 General . 39
6.8.2 Test Method . 39
6.8.2.1 Required documentation . 39
6.8.2.2 Cessation of emissions from the "Transmission enabled" state . 39
6.8.2.3 Cessation of emission from the "Transmission disabled" state . 40
6.8.2.4 Cessation of emission from the "Initial Phase" state . 40
6.8.2.4.1 EUTs transmitting initial bursts . 40
6.8.2.4.2 EUTs not transmitting initial bursts . 40
6.8.2.5 "Single action" means of cessation of emissions. 41
6.8.2.6 Fault conditions . 41
6.9 Identification of ESOMP . 42
6.9.1 Test arrangement . 42
6.9.2 Test method . 42
6.10 Control and monitoring functions . 42
6.10.1 General . 42
6.10.2 Test arrangement . 42
6.10.3 Processor monitoring- Test method . 42
6.10.4 Transmit subsystem monitoring-Test method . 42
6.10.5 Power-on/Reset-Test method . 43
6.10.6 Control Channel and Response Channel -Test method . 43
6.10.7 Network Control commands-Test method . 44
6.10.8 Initial burst transmission-Test method . 45
6.10.9 Inhibition of transmission-Test method . 45
Annex A (normative): HS Requirements and conformance Test specifications Table
(HS-RTT) . 47
Annex B (informative): Linear Polarization Alignment Error Calculation . 49
Annex C (normative): Radiated measurement . 50
ETSI
---------------------- Page: 5 ----------------------
6 ETSI E
...
Draft ETSI EN 303 979 V1.1.0 (2015-03)
HARMONIZED EUROPEAN STANDARD
Satellite Earth Stations and Systems (SES);
Harmonized EN for Earth Stations on Mobile Platforms
(ESOMP) transmitting towards satellites in non-geostationary
orbit in the 27,5 GHz to 29,1 GHz and 29,5 GHz to 30,0 GHz
frequency bands covering the essential requirements
of article 3.2 of the R&TTE Directive
---------------------- Page: 1 ----------------------
2 Draft ETSI EN 303 979 V1.1.0 (2015-03)
Reference
DEN/SES-00364
Keywords
antenna, earth station, mobile, non-GSO,
regulation, satellite
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2015.
All rights reserved.
TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.
TM
3GPP and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI
---------------------- Page: 2 ----------------------
3 Draft ETSI EN 303 979 V1.1.0 (2015-03)
Contents
Intellectual Property Rights . 7
Foreword . 7
Modal verbs terminology . 7
Introduction . 7
1 Scope . 9
2 References . 10
2.1 Normative references . 10
2.2 Informative references . 11
3 Definitions, symbols and abbreviations . 11
3.1 Definitions . 11
3.2 Symbols . 13
3.3 Abbreviations . 13
4 Technical requirements specifications . 14
4.1 General . 14
4.1.1 Environmental profile . 14
4.1.2 Operational configurations . 14
4.1.3 Determination of geographic location of the ESOMP . 14
4.1.4 EIRP for networks of ESOMPs . 15
Aggregate
4.1.5 Presentation of equipment for testing purposes . 15
4.1.6 Choice of model for testing . 15
4.1.7 Mechanical and electrical design . 15
4.1.7.1 General . 15
4.1.7.2 Marking (equipment identification) . 15
4.1.7.3 Equipment identification . 15
4.2 Conformance requirements . 16
4.2.1 Off-axis spurious radiation . 16
4.2.1.1 Justification . 16
4.2.1.2 Specification. 16
4.2.1.3 Conformance tests . 17
4.2.2 On-axis spurious radiation . 17
4.2.2.1 Justification . 17
4.2.2.2 Specification. 17
4.2.2.2.1 "Carrier-on" radio state . 17
4.2.2.2.2 "Carrier-off" and "Emissions disabled" radio states . 17
4.2.2.3 Conformance tests . 17
4.2.3 epfd Limits . 18
4.2.3.1 Justification . 18
4.2.3.2 Specification. 18
4.2.3.3 Conformance tests . 18
4.2.4 Uplink Power Control Specification . 18
4.2.5 Carrier suppression . 18
4.2.5.1 Justification . 18
4.2.5.2 Specification. 18
4.2.5.3 Conformance tests . 18
4.2.6 Antenna pointing and polarization alignment . 18
4.2.6.1 Antenna pointing accuracy . 18
4.2.6.1.1 Purpose . 18
4.2.6.1.2 Pointing accuracy specification . 18
4.2.6.1.3 On-axis cross polarization isolation specification . 19
4.2.6.1.4 Conformance tests . 19
4.2.6.2 Antenna Pointing Error Detection . 19
4.2.6.2.1 Purpose . 19
4.2.6.2.2 Pointing error detection specification . 19
ETSI
---------------------- Page: 3 ----------------------
4 Draft ETSI EN 303 979 V1.1.0 (2015-03)
4.2.6.2.3 Polarization angle alignment specification . 19
4.2.6.2.4 Conformance tests . 20
4.2.7 Cessation of emissions . 20
4.2.7.1 Justification . 20
4.2.7.2 Specification. 20
4.2.7.2.1 Specification 1: Mode of cessation of emissions . 20
4.2.7.2.2 Specification 2: Conditions under which the ESOMP shall cease emissions . 20
4.2.7.2.3 Specification 3: Cessation of emissions . 21
4.2.7.2.4 Specification 4: Fault conditions . 21
4.2.7.3 Conformance tests . 21
4.2.8 Identification of the ESOMP . 21
4.2.8.1 Justification . 21
4.2.8.2 Specification. 21
4.2.8.3 Conformance tests . 21
4.2.9 Control and Monitoring Functions (CMFs) . 22
4.2.9.1 ESOMP States . 22
4.2.9.1.1 General . 22
4.2.9.1.2 CMF state diagram . 23
4.2.9.2 Processor monitoring . 24
4.2.9.2.1 Justification . 24
4.2.9.2.2 Specification . 24
4.2.9.2.3 Conformance tests . 24
4.2.9.3 Transmit subsystem monitoring . 25
4.2.9.3.1 Justification . 25
4.2.9.3.2 Specification . 25
4.2.9.3.3 Conformance tests . 25
4.2.9.4 Power-on/Reset . 25
4.2.9.4.1 Justification . 25
4.2.9.4.2 Specification . 25
4.2.9.4.3 Conformance tests . 25
4.2.9.5 Control Channel (CC) and Response Channel (RC) . 25
4.2.9.5.1 Justification . 25
4.2.9.5.2 Specification . 25
4.2.9.5.3 Conformance tests . 26
4.2.9.6 Network control commands . 26
4.2.9.6.1 Justification . 26
4.2.9.6.2 Specification . 26
4.2.9.6.3 Conformance tests . 27
4.2.9.7 Initial burst transmission . 27
4.2.9.7.1 Justification . 27
4.2.9.7.2 Specification . 27
4.2.9.7.3 Conformance tests . 27
4.2.9.8 Inhibition of transmissions . 27
4.2.9.8.1 Justification . 27
4.2.9.8.2 Specification . 27
4.2.9.8.3 Conformance tests . 27
5 Testing for compliance with technical requirements . 28
5.1 Environmental conditions for testing . 28
5.2 Essential radio test suites . 28
6 Test methods for all aspects of the ESOMP . 28
6.1 General . 28
6.1.1 General requirements . 28
6.1.2 Interpretation of measurement results . 28
6.1.3 Measuring receiver . 29
6.2 Off-axis spurious radiation . 30
6.2.1 General . 30
6.2.2 Test method . 30
6.2.2.1 General . 30
6.2.2.2 Multi-carrier operation . 31
6.2.3 Measurements up to 1 000 MHz . 31
ETSI
---------------------- Page: 4 ----------------------
5 Draft ETSI EN 303 979 V1.1.0 (2015-03)
6.2.3.1 Test site . 31
6.2.3.2 Measuring receivers . 31
6.2.3.3 Procedure . 31
6.2.4 Measurements above 1 000 MHz . 32
6.2.4.1 General . 32
6.2.4.2 Identification of the significant frequencies of spurious radiation . 32
6.2.4.2.1 Test site. 32
6.2.4.2.2 Procedure . 32
6.2.4.3 Measurement of radiated power levels of identified spurious radiation . 32
6.2.4.3.1 Test site. 32
6.2.4.3.2 Procedure . 33
6.2.4.3 Measurement of conducted spurious radiation at the antenna flange . 34
6.2.3.4.1 Test site. 34
6.2.3.4.2 Procedure . 34
6.3 On-axis spurious radiation . 35
6.3.1 Test method . 35
6.3.1.1 General . 35
6.3.1.2 Test site . 35
6.3.1.3 Method of measurement . 35
6.3.1.3.1 General . 35
6.3.1.3.2 Method of measurement at the antenna flange . 35
6.3.1.3.3 Method of measurement for an EUT with antenna . 37
6.4 epfd limits . 38
6.5 Carrier suppression . 38
6.5.1 Test method . 38
6.6 Antenna pointing . 38
6.6.1 General . 38
6.6.2 Test method . 38
6.7 Polarization angle alignment capability . 39
6.7.1 General . 39
6.7.2 Test method . 39
6.8 Cessation of emissions of the ESOMP . 39
6.8.1 General . 39
6.8.2 Test Method . 39
6.8.2.1 Required documentation . 39
6.8.2.2 Cessation of emissions from the "Transmission enabled" state . 39
6.8.2.3 Cessation of emission from the "Transmission disabled" state . 40
6.8.2.4 Cessation of emission from the "Initial Phase" state . 40
6.8.2.4.1 EUTs transmitting initial bursts . 40
6.8.2.4.2 EUTs not transmitting initial bursts . 40
6.8.2.5 "Single action" means of cessation of emissions. 41
6.8.2.6 Fault conditions . 41
6.9 Identification of ESOMP . 42
6.9.1 Test arrangement . 42
6.9.2 Test method . 42
6.10 Control and monitoring functions . 42
6.10.1 General . 42
6.10.2 Test arrangement . 42
6.10.3 Processor monitoring- Test method . 42
6.10.4 Transmit subsystem monitoring-Test method . 42
6.10.5 Power-on/Reset-Test method . 43
6.10.6 Control Channel and Response Channel -Test method . 43
6.10.7 Network Control commands-Test method . 44
6.10.8 Initial burst transmission-Test method . 45
6.10.9 Inhibition of transmission-Test method . 45
Annex A (normative): HS Requirements and conformance Test specifications Table
(HS-RTT) . 47
Annex B (informative): Linear Polarization Alignment Error Calculation . 49
Annex C (normative): Radiated measurement . 50
ETSI
---------------------- Page: 5 ---
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.