SIST EN ISO 29022:2013
(Main)Dentistry - Adhesion - Notched-edge shear bond strength test (ISO 29022:2013)
Dentistry - Adhesion - Notched-edge shear bond strength test (ISO 29022:2013)
This International Standard specifies a shear test method used to determine the adhesive bond strength between direct dental restorative materials and tooth structure, e.g. dentine or enamel. The method as described is principally intended for dental adhesives. The method includes substrate selection, storage and handling of tooth structure, as well as the procedure for testing.
Zahnheilkunde - Haftfähigkeit - V-Kerb-Scherverbundfestigkeitsprüfung (ISO 29022:2013)
In dieser Internationalen Norm wird ein Abscherprüfverfahren beschrieben, mit dem die Abscher-verbundfestigkeit zwischen direkten zahnärztlichen Restaurationswerkstoffen und der Zahnstruktur, z. B. Dentin oder Schmelz, bestimmt werden kann. Das beschriebene Verfahren ist hauptsächlich für zahnärztliche Adhäsive vorgesehen. Das Verfahren beschreibt die Auswahl des Substrates, die Lagerung und Handhabung der Zahnstruktur, sowie die Durchführung der Prüfung.
ANMERKUNG 1 Weil die Prüfung der Haftfestigkeit an der Zahnstruktur techniksensitiv ist, sind Erfahrungen mit dem Prüfverfahren erforderlich.
ANMERKUNG 2 Das Prüfverfahren kann mit entsprechenden Änderungen auch für adhäsive Restaurationswerkstoffe (z. B. Glasionomerzemente) verwendet werden.
Médecine bucco-dentaire - Adhésion - Essai de résistance au cisaillement de bord cranté (ISO 29022:2013)
L'ISO 29022:2013 spécifie une méthode d'essai de cisaillement qui permet de déterminer la force d'adhérence entre les produits de restauration dentaire directe et la structure dentaire, par exemple la dentine ou l'émail. La méthode décrite est principalement destinée aux adhésifs dentaires. La méthode comprend le choix du substrat, le stockage et le conditionnement de la structure dentaire, ainsi que le mode opératoire d'essai.
Zobozdravstvo - Adhezija - Preskus oprijemne trdnosti škarij z nazobčanim rezilom (ISO 29022:2013)
Ta mednarodni standard določa preskusno metodo škarij za ugotavljanje oprijemne trdnosti lepila med neposrednimi dentalnimi obnovitvenimi materiali in zobno strukturo, npr. dentinom ali zobno sklenino. Opisana metoda je prvenstveno namenjena za dentalna lepila. Metoda vključuje izbiro podlage, shranjevanje zobne strukture in rokovanje z njo ter postopek preskušanja.
General Information
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 29022:2013
01-september-2013
=RER]GUDYVWYR$GKH]LMD3UHVNXVRSULMHPQHWUGQRVWLãNDULM]QD]REþDQLP
UH]LORP ,62
Dentistry - Adhesion - Notched-edge shear bond strength test (ISO 29022:2013)
Zahnheilkunde - Haftfähigkeit - V-Kerb-Scherverbundfestigkeitsprüfung (ISO
29022:2013)
Médecine bucco-dentaire - Adhésion - Essai de résistance au cisaillement de bord
cranté (ISO 29022:2013)
Ta slovenski standard je istoveten z: EN ISO 29022:2013
ICS:
11.060.10 =RERWHKQLþQLPDWHULDOL Dental materials
SIST EN ISO 29022:2013 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 29022:2013
---------------------- Page: 2 ----------------------
SIST EN ISO 29022:2013
EUROPEAN STANDARD
EN ISO 29022
NORME EUROPÉENNE
EUROPÄISCHE NORM
June 2013
ICS 11.060.10
English Version
Dentistry - Adhesion - Notched-edge shear bond strength test
(ISO 29022:2013)
Médecine bucco-dentaire - Adhérence - Essai de Zahnheilkunde - Adhäsion - Verbundprüfung der
résistance au cisaillement sur échantillons à bord entaillé Abscherfestigkeit mit ausgesparter Klinge (ISO
(ISO 29022:2013) 29022:2013)
This European Standard was approved by CEN on 11 April 2013.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2013 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 29022:2013: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 29022:2013
EN ISO 29022:2013 (E)
Contents Page
Foreword .3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 29022:2013
EN ISO 29022:2013 (E)
Foreword
This document (EN ISO 29022:2013) has been prepared by Technical Committee ISO/TC 106 “Dentistry” in
collaboration with Technical Committee CEN/TC 55 “Dentistry” the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by December 2013, and conflicting national standards shall be withdrawn
at the latest by December 2013.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
Endorsement notice
The text of ISO 29022:2013 has been approved by CEN as EN ISO 29022:2013 without any modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 29022:2013
---------------------- Page: 6 ----------------------
SIST EN ISO 29022:2013
INTERNATIONAL ISO
STANDARD 29022
First edition
2013-06-01
Dentistry — Adhesion — Notched-
edge shear bond strength test
Médecine bucco-dentaire — Adhérence — Essai de résistance au
cisaillement sur échantillons à bord entaillé
Reference number
ISO 29022:2013(E)
©
ISO 2013
---------------------- Page: 7 ----------------------
SIST EN ISO 29022:2013
ISO 29022:2013(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2013
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2013 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 29022:2013
ISO 29022:2013(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Tooth substrate and storage . 1
4.1 General . 1
4.2 Time after extraction . 2
4.3 Condition of teeth . 2
4.4 Initial preparation and storage of teeth . 2
5 Tooth surface preparation . 2
5.1 General . 2
5.2 Potting (mounting) of teeth . 2
5.3 Surface preparation . 3
5.4 Storage of prepared specimens . 3
6 Specimen production, handling and storage . 3
6.1 General . 3
6.2 Preconditioning . 3
6.3 Application of adhesive . 3
6.4 Insertion into bonding clamp . 4
6.5 Composite placement . 4
6.6 Specimen handling and storage . 4
7 Notched-edge shear test . 5
7.1 Apparatus . 5
7.2 Shear loading . 6
7.3 Test . 6
7.4 Recording and treatment of results . 6
7.5 Report . 6
Annex A (normative) Detailed drawings of notched-edge shear apparatus .8
© ISO 2013 – All rights reserved iii
---------------------- Page: 9 ----------------------
SIST EN ISO 29022:2013
ISO 29022:2013(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International
Standards adopted by the technical committees are circulated to the member bodies for voting.
Publication as an International Standard requires approval by at least 75 % of the member bodies
casting a vote.
ISO 29022 was prepared by Technical Committee ISO/TC 106, Dentistry, Subcommittee SC 1, Filling and
restorative materials.
iv © ISO 2013 – All rights reserved
---------------------- Page: 10 ----------------------
SIST EN ISO 29022:2013
ISO 29022:2013(E)
Introduction
The International Organization for Standardization (ISO) draws attention to the fact that it is claimed that
compliance with this document may involve the use of a patent concerning testing shear bond strength.
ISO takes no position concerning the evidence, validity and scope of this patent right.
The holder of this patent right has ensured ISO that he/she is willing to negotiate licenses under
reasonable and non-discriminatory terms and conditions with applicants throughout the world. In
this respect, the statement of the holder of this patent right is registered with ISO. Information may be
obtained from:
Neil T. Jessop, Ultradent Products, Inc., 505 West 10200 South, South Jordan, Utah 84095-3942, USA.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights other than those identified above. ISO shall not be held responsible for identifying any or
all such patent rights.
The purpose of this International Standard is to establish a simple and easy to use method for documenting
a claim that a material adheres to tooth substance. While the method described in this International
Standard has been used for comparing dental adhesive materials, users of this International Standard
should evaluate usefulness of this method for their particular application(s). There is a variety of other
dental adhesion test methods that may also be suitable or preferable, depending on the objective (e.g.
academic research).
© ISO 2013 – All rights reserved v
---------------------- Page: 11 ----------------------
SIST EN ISO 29022:2013
---------------------- Page: 12 ----------------------
SIST EN ISO 29022:2013
INTERNATIONAL STANDARD ISO 29022:2013(E)
Dentistry — Adhesion — Notched-edge shear bond
strength test
1 Scope
This International Standard specifies a shear test method used to determine the adhesive bond strength
between direct dental restorative materials and tooth structure, e.g. dentine or enamel. The method as
described is principally intended for dental adhesives. The method includes substrate selection, storage
and handling of tooth structure, as well as the procedure for testing.
NOTE 1 Testing adhesion to tooth structure is technique sensitive and experience with the test method is required.
NOTE 2 With modification, it may be possible to use this method for adhesive restorative materials (e.g. glass-
ionomer materials).
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.
ISO 1942, Dentistry — Vocabulary
ISO 3696, Water for analytical laboratory use — Specification and test methods
ISO 6344−1, Coated abrasives — Grain size analysis — Part 1: Grain size distribution test
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 1942 and the following apply.
3.1
bond strength
force per unit area required to break a bonded assembly with failure occurring in or near the
adhesive/adherend interface
3.2
direct dental restorative material
material used to restore a tooth that is placed in the plastic or unset state and sets intraorally when
used clinically
3.3
substrate
material upon the surface of which an adhesive is spread for any purpose, such as bonding or coating
4 Tooth substrate and storage
4.1 General
Use bovine incisors or human erupted permanent third molars for the measurement of bond strength.
Record the type of substrate used.
© ISO 2013 – All rights reserved 1
---------------------- Page: 13 --------
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.