SIST EN 960:2006
(Main)Headforms for use in the testing of protective helmets
Headforms for use in the testing of protective helmets
This European standard specifies the dimensional and constructional details of headforms for use in the testing of protective helmets. A recommended method of constructing wooden headforms is given in Annexes B and C.
Prüfköpfe zur Prüfung von Schutzhelmen
Diese Europäische Norm legt die Einzelheiten zu den Größen und der Konstruktion von Prüfköpfen zur
Prüfung von Schutzhelmen fest.
Fausses tetes a utiliser lors des essais de casques de protection
La présente Norme européenne spécifie les dimensions et les détails de construction des fausses tetes a
utiliser lors des essais de casques de protection.
Modeli glav za preskušanje zaščitnih čelad
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 960:2006
01-december-2006
1DGRPHãþD
SIST EN 960:1996
SIST EN 960:1996/A1:1999
0RGHOLJODY]DSUHVNXãDQMH]DãþLWQLKþHODG
Headforms for use in the testing of protective helmets
Prüfköpfe zur Prüfung von Schutzhelmen
Fausses tetes a utiliser lors des essais de casques de protection
Ta slovenski standard je istoveten z: EN 960:2006
ICS:
13.340.20 Varovalna oprema za glavo Head protective equipment
SIST EN 960:2006 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
EUROPEAN STANDARD
EN 960
NORME EUROPÉENNE
EUROPÄISCHE NORM
June 2006
ICS 13.340.20 Supersedes EN 960:1994
English Version
Headforms for use in the testing of protective helmets
Fausses têtes à utiliser lors des essais de casques de Prüfköpfe zur Prüfung von Schutzhelmen
protection
This European Standard was approved by CEN on 18 May 2006.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Central Secretariat or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania,
Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2006 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 960:2006: E
worldwide for CEN national Members.
---------------------- Page: 2 ----------------------
EN 960:2006 (E)
Contents Page
Foreword. 3
Introduction . 4
1 Scope . 6
2 Terms and definitions . 6
3 Requirements. 7
3.1 Materials and general characteristics. 7
3.2 Dimensions . 8
3.3 Marking . 8
Annex A (normative) Spherical coordinates . 11
Annex B (informative) Equations defining the radii of the spherical coordinate system for sizes 495 to
645 . 33
Annex C (informative) Tabular history of headform H, 565 mm and dimension y. 36
Annex ZA (informative) Relationship between this European Standard and the Essential Requirements of
EU Directive 89/686/EEC . 37
Bibliography. 38
2
---------------------- Page: 3 ----------------------
EN 960:2006 (E)
Foreword
This document (EN 960:2006) has been prepared by Technical Committee CEN/TC 158 "Head protection", the
secretariat of which is held by BSI.
This European Standard shall be given the status of a national standard, either by publication of an identical text
or by endorsement, at the latest by December 2006, and conflicting national standards shall be withdrawn at the
latest by December 2006.
This document supersedes EN 960:1994.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EU Directive 89/686/EEC.
For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this document.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden,
Switzerland and United Kingdom.
3
---------------------- Page: 4 ----------------------
EN 960:2006 (E)
Introduction
In preparing this revision of EN 960 it was decided to address several areas of concern, which had arisen
during the life of the previous version of this European Standard, namely:
dimensional errors are present;
several desirable definitions, characteristics and headform markings are missing;
it is impossible to verify or demonstrate compliance of a headform with the standard because of the
absence of tolerances associated with the specified dimensions;
the method of dimensioning the headforms, whilst essential to enable manufacture of the original wooden
headforms, does not facilitate a straightforward method of tolerancing these dimensions.
It was also acknowledged that headforms are specified, in various helmet standards, for tests where other than
a full headform is required. Accordingly, in this revision, “half headforms” and “three-quarter headforms” have
been specified, in addition to “full headforms”.
Half headforms are usually rigidly mounted (not falling), so consequently their mass is not important and is,
therefore, not specified in this European Standard.
Three-quarter headforms are also used rigidly mounted, but are often used in a falling headform and helmet
assembly arrangement for shock absorption tests, where they are typically supported by means of a ball joint
and cantilever. In such cases, the falling mass comprises that of the headform and of the supporting system.
Some helmet standards specify total falling mass, whereas some specify only the mass of the headform. For
this reason, only the dimensions, not the masses, of the three-quarter headforms are specified in this European
Standard. It is to be hoped that in future revisions, mass will also be agreed.
The opportunity has been taken to specify more adequately the centre of gravity and the geometric centre of
headforms, including the nomination of which of these characteristics is more appropriate to the different types
of headform specified and to whether the headforms are intended to be used rigidly mounted or in guided fall or
in free fall.
Whilst, in the past, the nominal sizes of headforms have been specified in multiples of ten millimetres (50, 51,
52 etc.), the actual circumferences are closer to five millimetres greater or less than nominal. In this revision
therefore, the size designations have been specified according to the actual nominal circumference, in
increments of ten millimetres (505, 515, 525 etc.).
Helmets for children have been available for a number of years but headforms to test them are not specified in
EN 960:1994. Following searches of the literature it was found that smaller headforms were specified in other
publications. However, when comparing the dimensions given for these headforms with those specified for the
headforms in EN 960, it was quite obvious that these smaller headforms were not specified as comprehensively
as those in EN 960. Hence, incorporation of these data would be neither straightforward nor consistent. It was
decided therefore, to develop, from the existing EN 960 dimensions, the specification for five new, smaller,
headforms below size 495.
In order to overcome the problems of tolerancing, it was decided to replace the existing dimensioning system
with a spherical coordinate system. Namely, using point ‘R’ (the geometric centre) as the datum and then
specifying the radius of points on the outer surface of the headform at various angles measured from point ‘R’.
Appropriate tolerances have then been assigned to the radius and to the angles.
As part of the process, linear regression lines through the existing data sets for head sizes A to Q were
established and the spherical coordinates were specified from the equations of these regression lines. The
coordinates of the new, smaller heads, sizes 445 to 485, were derived by simple scaling of the corresponding
points of head size 495 in proportion to the respective circumferences.
4
---------------------- Page: 5 ----------------------
EN 960:2006 (E)
Partly because of the impossibility of assigning these smaller heads code letters less than A (the other end of
the alphabet was considered and dismissed), it was decided to abandon the code letter system of identification.
Further, the concept of ‘internal circumference of a helmet’ was removed. Instead, headforms have now been
classified only according to a size designation, which corresponds to their circumference.
During this revision the opportunity was taken to correct obvious errors present in the existing tables, which
evidence themselves on the headforms as spurious bumps and depressions. Also, the data points were
smoothed where obvious discontinuities occurred and the protruding chin was removed.
Whilst, ideally, the dimensions of headforms already in existence, which ‘satisfy’ EN 960:1994, should comply
with the dimensions given in this revision, because of the preceding paragraph, there are a few points which fall
outside of the tolerances specified.
The spherical coordinates of head sizes 445 to 645 are given in the normative Annex A. The equations, which
define the radii of the spherical coordinates in terms of headform circumference and vertical and horizontal
angles, are given in the informative Annex B.
The first international draft standard for headforms was ISO/R1511:1970, followed many years later by
ISO/DIS 6220:1983. Both of these documents were based upon the British Standard, BS 1869:1960, which
itself was developed from the first set of test headforms produced by the UK Transport and Road Research
Laboratory in the 1950s. The TRRL headforms were designated solely by their size, given in inches. The
increment between each size was one eighth of an inch.
During the drafting of BS 1869, the concept of code letters was introduced, but unfortunately, errors of
transposition from the TRRL data were made, which resulted in incorrect dimensions being specified and the
inclusion of headform code letter H, circumference 565 mm. This headform was also specified in R1511, but
subsequently dropped from ISO/DIS 6220 and EN 960:1994. The dimensional errors however, were carried
forward through R1511, ISO/DIS 6220 and EN 960:1994.
A summary of this brief history is tabulated in informative Annex C.
5
---------------------- Page: 6 ----------------------
EN 960:2006 (E)
1 Scope
This European Standard specifies the dimensional and constructional details of headforms for use in the testing
of protective helmets.
2 Terms and definitions
For the purposes of this European Standard, the following terms and definitions apply.
2.1
headform
three dimensional approximation of part, or all, of the human head, excluding facial features and pinnae. Three
general forms are characterized in this European Standard, viz:
full headform - extends from the crown downwards to below the chin and includes part of the neck;
three-quarter headform - extends from the crown downwards at the sides and rear to below the level of the
basic plane;
half headform - extends from the crown downwards at the sides and rear to approximately the level of the
basic plane
2.2
size designation
circumference of a given headform, expressed in mm, as shown in Table 1
2.3
circumference, C
for a given headform, the length of its periphery, measured at the level of the reference plane
2.4
AA’ plane
for a given headform, the horizontal transverse plane located at a vertical distance 12,7 mm above and parallel
to the reference plane
NOTE This plane is deemed to correspond to the level of the lower edge of the headband of a helmet. It is the basis upon
which the size designation of a helmet may be specified.
2.5
reference plane
for a given headform, when erect, the horizontal plane located at a vertical distance ‘y’ measured down the
central vertical axis from the centre of the crown
NOTE All horizontal datum levels are quoted relative to this plane.
2.6
central vertical axis
vertical axis lying along the intersection of the vertical longitudinal plane and the vertical transverse plane
2.7
crown
area on the upper, outer surface of a headform, centred on the central vertical axis
2.8
vertical longitudinal plane
for a given headform, the vertical plane of symmetry, perpendicular to the reference plane and located mid-way
between the left hand and right hand extremities of the headform
6
---------------------- Page: 7 ----------------------
EN 960:2006 (E)
NOTE This corresponds to the mid-sagittal plane of the human head.
2.9
vertical transverse plane
for a given headform, the vertical plane perpendicular to both the vertical longitudinal plane and the reference
plane and located mid-way between the front and rear extremities of the headform
NOTE This corresponds to the coronal plane of the human head.
2.10
basic plane
for a given headform, the horizontal plane located at a vertical distance ‘x’ below and parallel to the reference
plane
NOTE This corresponds to the basic plane of the human head being the longitudinal plane which passes through the lower
level of the eye orbits and the upper level of the external opening of the ear canals.
2.11
centre of gravity of the three-quarter headform
point A
for a given headform, the point on the central vertical axis located at a vertical distance 12,7mm above the
reference plane
2.12
centre of gravity of the full headform
point G
for a given headform, the point on the central vertical axis located at a vertical distance ‘z’ below the reference
plane, as given in Table 1
2.13
geometric centre
point R
for a given headform, the point on the central vertical axis, located at its intersection with the reference plane
NOTE This point is the datum for all the dimensions given in Annex A.
3 Requirements
3.1 Materials and general characteristics
3.1.1 Headforms for shock absorption and penetration tests, with falling headform/helmet assembly
The headforms shall be made of metal and, together with any means for their support, shall exhibit no
resonance below a frequency of 2 000 Hz.
Full headforms shall have the following characteristics:
a) the centre of gravity shall be located within a 10 mm radius of point G on the central vertical axis;
b) a facility for attaching an accelerometer shall be incorporated such that, with the headform in any angular
orientation, the respective sensitive axes of the accelerometer shall pass within 10 mm of point G;
c) the appropriate mass, if specified in Table 1.
Three-quarter headforms shall have the following characteristics:
i) the centre of gravity shall be located within a 10 mm radius of point A on the central vertical axis;
7
---------------------- Page: 8 ----------------------
EN 960:2006 (E)
ii) a facility for attaching an accelerometer shall be incorporated within the headform or its means of
support, such that, with the headform in any angular orientation, the respective sensitive axes of the
accelerometer shall pass within 10 mm of point A.
NOTE 1 For this type of test, full and three-quarter headforms may be specified in the respective helmet standard.
NOTE 2 The geometry of the half headform does not facilitate its use for this type of test.
NOTE 3 Care should be taken to ensure that the total mass of the headform, when fitted with the accelerometer and
its means of attachment, falls within any tolerances specified in either this standard or the respective helmet standard, as
appropriate.
3.1.2 Headforms for shock absorption and penetration tests, with rigidly mounted (not falling)
headform/helmet assembly
The headforms shall be made of a rigid material which does not affect the measurements of shock absorption
or penetration (e.g. wood). The headforms, together with their means of support, shall exhibit no resonance
below a frequency of 2 000 Hz.
NOTE For this type of test, full, three-quarter and half headforms may be specified in the respective helmet standard.
3.1.3 Headforms for geometric examination or positional marking of the helmet
The headforms shall be made of any suitable material.
3.1.4 Headforms for other tests
When a test requires the headform to be made from a specific material or to possess specific material
characteristics (e.g. thermal or electrical conductivity, thermal capacity etc.), these materials and characteristics
shall be as specified in the relevant helmet standard.
3.2 Dimensions
The outer surface of each headform shall lie within the locus of the coordinates given in Annex A. Between
coordinate points, the outer surface of the headform shall be curved and smooth.
th
NOTE The exact geometry of the surface between the specified coordinates may be determined, for example, by a 5 order
spline function.
3.3 Marking
3.3.1 Headforms for geometric examination or positional marking of the helmet shall be marked with:
a) size designation of the headform;
b) reference plane;
c) basic plane;
d) vertical longitudinal plane;
e) vertical transverse plane.
3.3.2 All other headforms shall be marked, at least, with the size designation of the headform.
NOTE Other marking may be required by specific helmet standards.
8
---------------------- Page: 9 ----------------------
EN 960:2006 (E)
1 4
2 5
6
3
7
Section on vertical longitudinal plane
Key
1 AA' plane
2 reference plane
3 basic plane
4 point A
5 point R
6 point G
7 central vertical axis
Figure 1 — Principal planes and reference points of a headform
9
z
12,7
x
y
h
---------------------- Page: 10 ----------------------
EN 960:2006 (E)
Table 1 — Dimensions for Figure 1 and headform masses
Size
h (mm) x (mm) y (mm) z (mm) Mass (g)
designation
445 108,5 21,0 81,7 9,9
455 110,6 21,5 83,3 10,1
1 970 ± 75
465 112,7 22,0 84,8 10,4
475 114,8 22,5 86,4 10,6
485 116,9 23,0 88,0 10.8
495 119,0 23,5 89,7 11,1
3 100 ± 100
505 121,1 24,0 91,2 11,3
515 123,2 24,5 92,7 11,5
525 125,3 25,0 94,5 11,7
535 127,4 25,5 96,0 11,9 4 100 ± 120
545 129,5 26,0 97,5 12,1
555 131,6 26,5 99,1 12,3
565 133,7 27,0 100,8 12,5
575 135,8 27,5 102,4 12,7 4 700 ± 140
585 137,9 28,0 103,9 12,9
595 140,0 28,5 105,4 13,1
605 142,1 29,0 107,2 13,3 5 600 ± 160
615 144,2 29,5 108,7 13,5
625 146,3 30,0 110,2 13,7
6 100 ± 180
635 148,4 30,5 111,8 13,9
645 150,5 31,0 113,5 14,1
10
---------------------- Page: 11 ----------------------
EN 960:2006 (E)
Annex A
(normative)
Spherical coordinates
The spherical coordinates are given in Tables A.1 to A.21.
11
---------------------- Page: 12 ----------------------
EN 960:2006 (E)
Table A.1 — Spherical coordinates for full headform size 445
Angle H
1 - 445
0 15 30 45 60 75 90 105 120 135 150 165 180
90 80,3 80,3 80,3 80,3 80,3 80,3 80,3 80,3 80,3 80,3 80,3 80,3 80,3
79,3 79,1 79,1 79,2 79,4 79,8 79,8 80,1 80,8 81,0 81,6 81,7 81,6
80
70 78,9 78,8 78,8 78,8 78,6 78,6 78,7 79,5 80,7 81,9 82,8 83,1 83,0
60 79,6 79,6 79,6 78,7 77,5 76,7 76,9 78,1 79,8 82,1 83,6 83,8 83,8
Angle V
50 80,8 80,7 80,8 78,4 75,7 74,2 74,2 75,9 78,2 81,3 83,7 83,8 83,7
above
40 81,3 81,1 81,0 77,1 73,2 71,0 70,9 72,9 75,9 79,7 83,0 83,1 83,1
80,7 80,5 79,8 74,7 69,9 67,4 67,1 69,4 73,1 77,4 81,4 82,0 82,2
30
20 79,4 79,0 77,5 71,6 66,3 63,6 63,4 66,0 69,8 74,6 79,3 80,8 81,2
10 78,5 77,5 75,3 68,8 63,5 60,6 60,5 63,2 66,7 71,7 76,9 79,6 80,1
Reference
0 79,0 77,4 74,4 67,6 62,4 59,7 59,5 62,0 65,7 70,5 75,3 78,4 79,0
plane
10 80,2 79,3 75,4 67,7 62,0 59,9 59,9 61,8 64,8 69,2 72,8 75,3 75,7
20 84,0 85,1 77,3 69,2 62,8 59,8 57,5 59,6 62,2 66,1 69,6 71,8 72,3
30 91,2 92,5 80,7 71,4 65,9 63,3 57,7 59,1 61,9 65,6 68,8 70,4 69,9
40 103,1 104,5 88,6 77,8 70,9 65,1 61,7 62,3 64,5 67,3 69,5 70,4 69,6
46 113,7 115,2 93,9 83,4 76,2 68,8 66,3 66,8 68,4 70,4 71,8 72,6 72,3
Angle V
below
50 110,1 111,2 97,4 87,0 81,2 73,6 70,8 71,5 72,5 74,3 75,2 76,1 76,3
52 107,2 108,3 97,5 88,6 84,2 76,4 73,5 74,4 75,3 76,9 77,8 78,7 79,2
55 103,3 104,3 96,2 89,0 84,2 80,2 78,6 79,7 80,5 82,0 82,8 84,0 84,7
60 97,6 98,4 94,4 88,2 89,5 89,6 90,1 91,5 92,6 94,1 95,0 96,6 97,6
65 101,7 103,5 100,6 101,9 105,5 105,6 106,8 108,4 109,7 111,6 112,7 114,4 115,3
V = Vertical angle above or below the reference plane Angles in degrees, to be measured with an uncertainty of measurement not exceeding ± 0,2°.
H = Angle of vertical slice, measured in horizontal plane,
Radii in mm, with a tolerance of ± 0,5 % and measured with an uncertainty of measurement not
from front of mid-sagittal plane exceeding 0,1 mm.
The jaw line shall be radiused along its length with a nominal 5 mm radius. The base of the neck shall be squared off perpendicular to the central vertical axis.
NOTE The surface corresponding to the radii shown in italics lies below the jaw line.
12
---------------------- Page: 13 ----------------------
EN 960:2006 (E)
Table A.2 — Spherical coordinates for full headform size 455
Angle H
1 - 455
0 15 30 45 60 75 90 105 120 135 150 165 180
90 82,1 82,1 82,1 82,1 82,1 82,1 82,1 82,1 82,1 82,1 82,1 82,1 82,1
81,1 80,9 80,9 81,0 81,2 81,6 81,6 81,9 82,6 82,8 83,4 83,5 83,5
80
70 80,6 80,6 80,6 80,6 80,4 80,3 80,5 81,3 82,5 83,7 84,7 84,9 84,9
60 81,4 81,4 81,4 80,5 79,2 78,4 78,6 79,9 81,6 83,9 85,5 85,7 85,6
Angle V
50 82,6 82,5 82,6 80,1 77,4 75,9 75,9 77,6 80,0 83,1 85,6 85,7 85,6
above
40 83,1 83,0 82,8 78,9 74,8 72,6 72,5 74,5 77,6 81,5 84,8 85,0 85,0
82,5 82,3 81,6 76,4 71,5 68,9 68,7 71,0 74,7 79,1 83,2 83,9 84,1
30
20 81,2 80,7 79,3 73,3 67,8 65,1 64,9 67,5 71,4 76,2 81,0 82,6 83,0
10 80,3 79,2 77,0 70,3 64,9 62,0 61,9 64,6 68,2 73,3 78,7 81,3 81,9
Reference
0 80,7 79,1 76,1 69,1 63,8 61,1 60,9 63,4 67,2 72,1 77,0 80,1 80,7
plane
10 82,0 81,1 77,1 69,2 63,4 61,2 61,3 63,2 66,2 70,7 74,4 77,0 77,4
20 85,9 87,0 79,1 70,7 64,3 61,2 58,7 61,0 63,6 67,6 71,1 73,4 73,9
30 93,2 94,5 82,5 73,0 67,3 64,8 59,0 60,5 63,3 67,1 70,4 72,0 71,4
40 105,4 106,9 90,6 79,5 72,5 66,6 63,1 63,7 66,0 68,9 71,0 72,0 71,2
46 116,2 117,8 96,0 85,3 77,9 70,4 67,8 68,3 69,9 72,0 73,5 74,3 74,0
Angle V
below
50 112,6 113,7 99,6 89,0 83,1 75,2 72,4 73,1 74,2 75,9 76,9 77,8 78,0
52 109,6 110,7 99,7 90,6 86,1 78,1 75,2 76,1 77,0 78,6 79,5 80,5 80,9
55 105,6 106,6 98,3 91,0 86,1 82,0 80,4 81,5 82,4 83,8 84,6 85,8 86,6
60 99,8 100,6 96,5 90,2 91,5 91,7 92,1 93,5 94,7 96,2 97,2 98,8 99,8
65 104,0 105,8 102,9 104,2 107,9 108,0 109,2 110,8 112,2 114,1 115,2 117,0 117,9
V = Vertical angle above or below the reference plane Angles in degrees, to be measured with an uncertainty of measurement not exceeding ± 0,2°.
H = Angle of vertical slice, measured in horizontal plane,
Radii in mm, with a tolerance of ± 0,5 % and measured with an uncertainty of measurement not
from front of mid-sagittal plane exceeding 0,1 mm.
The jaw line shall be radiused along its length with a nominal 5 mm radius. The base of the neck shall be squared off perpendicular to the central vertical axis.
NOTE The surface corresponding to the radii shown in italics lies below the jaw line.
13
---------------------- Page: 14 ----------------------
EN 960:2006 (E)
Table A.3 — Spherical coordinates for full headform size 465
Angle H
1 - 465
0 15 30 45 60 75 90 105 120 135 150 165 180
90 83,9 83,9 83,9 83,9 83,9 83,9 83,9 83,9 83,9 83,9 83,9 83,9 83,9
82,9 82,6 82,6 82,8 83,0 83,3 83,4 83,7 84,4 84,6 85,3 85,4 85,3
80
70 82,4 82,3 82,4 82,4 82,2 82,1 82,3 83,0 84,4 85,5 86,6 86,8 86,7
60 83,2 83,1 83,2 82,3 81,0 80,2 80,4 81,6 83,4 85,8 87,4 87,6 87,5
Angle V
50 84,4 84,3 84,4 81,9 79,2 77,6 77,6 79,3 81,7 85,0 87,5 87,5 87,5
above
40 84,9 84,8 84,6 80,6 76,5 74,2 74,1 76,2 79,3 83,3 86,7 86,8 86,9
84,3 84,2 83,4 78,1 73,0 70,4 70,2 72,6 76,3 80,9 85,1 85,7 85,9
30
20 83,0 82,5 81,0 74,9 69,3 66,5 66,3 69,0 72,9 77,9 82,8 84,4 84,8
10 82,1 80,9 78,7 71,8 66,3 63,4 63,3 66,1 69,7 75,0 80,4 83,1 83,7
Reference
0 82,5 80,9 77,7 70,7 65,2 62,4 62,2 64,8 68,7 73,7 78,7 81,9 82,5
plane
10 83,8 82,9 78,8 70,7 64,8 62,5 62,6 64,6 67,7 72,3 76,1 78,7 79,1
20 87,8 89,0 80,8 72,3 65,7 62,5 60,0 62,3 65,0 69,1 72,7 75,0 75,5
30 95,3 96,6 84,3 74,6 68,8 66,2 60,3 61,8 64,7 68,5 71,9 73,5 73,0
40 107,7 109,2 92,6 81,3 74,1 68,0 64,4 65,1 67,4 70,4 72,6 73,6 72,7
46 118,8 120,4 98,2 87,1 79,6 71,9 69,3 69,8 71,4 73,6 75,1 75,9 75,6
Angle V
below
50 115,1 116,2 101,8 90,9 84,9 76,9 74,0 74,7 75,8 77,6 78,6 79,5 79,8
52 112,0 113,1 101,9 92,6 88,0 79,8 76,9 77,7 78,7 80,4 81,2 82,3 82,7
55 107,9 109,0 100,5 93,0 88,0 83,8 82,2 83,3 84,2 85,7 86,5 87,7 88,5
60 102,0 102,9 98,6 92,2 93,5 93,7 94,1 95,6 96,7 98,3 99,3 100,9 102,0
65 106,3 108,1 105,1 106,5 110,3 110,3 111,6 113,3 114,7 116,6 117,8 119,6 120,5
V = Vertical angle above or below the reference plane Angles in degrees, to be measured with an uncertainty of measurement not exceeding ± 0,2°.
H = Angle of vertical slice, measured in horizontal plane,
Radii in mm, with a tolerance of ± 0,5 % and measured with an uncertainty of measurement not
from front of mid-sagittal plane exceeding 0,1 mm.
The jaw line shall be radiused along its length with a nominal 5 mm radius. The base of the neck shall be squared off perpendicular to the central vertical axis.
NOTE The surface corresponding to the radii shown in italics lies below the jaw line.
14
---------------------- Page: 15 ----------------------
EN 960:2006 (E)
Table A.4 — Spherical coordinates for full headform size 475
Angle H
1 - 475
0 15 30 45 60 75 90 105 120 135 150 165 180
90 85,7 85,7 85,7 85,7 85,7 85,7 85,7 85,7 85,7 85,7 85,7 85,7 85,7
84,7 84,4 84,4 84,6 84,8 85,1 85,2 85,5 86,2 86,5 87,1 87,2 87,2
80
70 84,2 84,1 84,1 84,1 83,9 83,9 84,1 84,8 86,2 87,4 88,4 88,6 88,6
60 85,0 84,9 85,0 84,0 82,7 81,9 82,1 83,4 85,2 87,6 89,2 89,5 89,4
Angle V
50 86,2 86,1 86,2 83,7 80,9 79,2 79,2 81,0 83,5 86,8 89,3 89,4 89,4
above
40 86,8 86,6 86,5 82,3 78,1 75,8 75,7 77,8 81,0 85,1 88,6 88,7 88,7
86,2 86,0 85,2 79,8 74,6 71,9 71,7 74,1 78,0 82,6 86,9 87,6 87,8
30
20 84,8 84,3 82,8 76,5 70,8 67,9 67,7 70,4 74,5 79,6 84,6 86,2 86,6
10 83,8 82,7 80,4 73,4 67,7 64,7 64,6 67,5 71,2 76,6 82,1 84,9 85,5
Reference
0 84,3 82,6 79,4 72,2 66,6 63,8 63,5 66,2 70,2 75,2 80,4 83,6 84,3
plane
10 85,6 84,7 80,5 72,3 66,2 63,9 64,0 66,0 69,1 73,8 77,7 80,4 80,9
20 89,7 90,9 82,6 73,8 67,1 63,9 61,3 63,7 66,4 70,6 74,3 76,6 77,2
30 97,3 98,7 86,1 76,2 70,3 67,6 61,6 63,1 66,1 70,0 73,5 75,1 74,6
40 110,1 111,5 94,5 83,0 75,7 69,5 65,8 66,5 68,9 71,9 74,1 75,2 74,3
46 121,4 123,0 100,3 89,0 81,3 73,5 70,8 71,3 73,0 75,2 76,7 77,5 77,2
Angle V
below
50 117,5 118,7 104,0 92,9 86,7 78,5 75,5 76,3 77,4 79,3 80,3 81,3 81,5
52 114,4 115,6 104,1 94,6 89,9 81,5 78,5 79,4 80,4 82,1 83,0 84,0 84,5
55 110,2 111,3 102,6 95,0 89,9 85,6 83,9 85,0 86,0 87,5 88,3 89,6 90,4
60 104,2 105,1 100,8 94,1 95,5 95,7 96,2 97,6 98,8 100,4 101,4 103,1 104,1
65 108,6 110,5 107,4 108,8 112,6 112,7 114,0 115,7 117,1 119,2 120,3 122,1 123,1
V = Vertical angle above or below the reference plane Angles in degrees, to be measured with an uncertainty of measurement not exceeding ± 0,2°.
H = Angle of vertical slice, measured in horizontal plane,
Radii in mm, with a tolerance of ± 0,5 % and measured with an uncertainty of measurement not
from front of mid-sagittal plane exceeding 0,1 mm.
The jaw line shall be radiused along its length with a nominal 5 mm radius. The base of the neck shall be squared off perpendicular to the central vertical axis.
NOTE The surface corresponding to the radii shown in italics lies below the jaw line.
15
---------------------- Page: 16 ----------------------
EN 960:2006 (E)
Table A.5 — Spherical coordinates for full headform size 485
Angle H
1 - 485
0 15 30 45 60 75 90 105 120 135 150 165 180
90 87,5 87,5 87,5 8
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.