SIST EN 303 039 V2.1.2:2016

Land Mobile Service - Multichannel transmitter specification for the PMR Service - Harmonised Standard covering the essential requirements of article 3.2 of the Directive 2014/53/EU

The present document covers the technical requirements for multiple channel radio transmitters used in stations in the Private Mobile Radio (PMR) service.
It applies to use in the land mobile service, operating on radio frequencies between 30 MHz and 3 GHz, with channel separations of < 10 kHz, 12,5 kHz, 20 kHz, 25 kHz, 50 kHz, 100 kHz and 150 kHz.
It applies to equipment for continuous and/or discontinuous transmission of data and/or digital speech and/or analogue speech and using constant envelope or non-constant envelope modulation.
The equipment comprises a transmitter capable of simultaneous amplification or transmission on two or more RF channels, or an amplifier which when operated with transmitter equipment provides simultaneous transmission on two or more RF channels. The types of equipment covered by the present document are as follows:
• base station (equipment fitted with an antenna connector, intended for use in a fixed location);
• mobile station (equipment fitted with an antenna connector, normally used in a vehicle or as a transportable);
• those hand portable stations:
a) fitted with an antenna connector; or
b) without an external antenna connector (integral antenna equipment), but fitted with a permanent internal or a temporary internal 50 Ω Radio Frequency (RF) connector which allows access to the transmitter output; and
• any equipment that may be used in combination with any of the above equipments when directly connected to those equipments for the amplification of the transmitter output signals of two or more individual equipments.
Types of equipment not covered by the present document are as follows:
• hand portable equipment without an external or internal RF connector and without the possibility of having a temporary internal 50 Ω RF connector is not covered by the present document;
• any equipment using passive combining solutions where each transmitter connected to the passive combining system transmits on a single channel, as detailed in ETSI EG 200 053 [i.2], clause H.3.
These specifications apply to the transmitter or transmitter amplifier only. If a receiver is fitted to the same equipment, the receiver specifications in the relevant specification (references [i.5] to [i.12]) also apply.
These specifications do not necessarily include all the characteristics that may be required by a user of equipment, nor do they necessarily represent the optimum performance achievable.
In addition to the present document, other ENs that specify technical requirements in respect of essential requirements under other parts of article 3 of the Radio Equipment Directive [i.3] may apply to equipment within the scope of the present document.

Storitev kopenskih mobilnih komunikacij - Specifikacija večkanalnega oddajnika za storitev PMR - Harmonizirani standard, ki zajema bistvene zahteve člena 3.2 direktive 2014/53/EU

Ta dokument zajema tehnične zahteve za večkanalne radijske oddajnike, ki se uporabljajo v postajah za storitev zasebnega mobilnega radia (PMR).
Uporablja se za storitev kopenskih mobilnih komunikacij, ki deluje prek radijskih frekvenc med 30 MHz in 3 GHz ter vključuje medkanalske razmike < 10 kHz, 12,5 kHz, 20 kHz, 25 kHz, 50 kHz, 100 kHz in 150 kHz.
Uporablja se za opremo za neprekinjen in/ali prekinjen prenos podatkov in/ali digitalnega govora in/ali analognega govora, ki uporablja modulacijo s konstantno ali nekonstantno ovojnico.
Oprema vključuje oddajnik, ki omogoča simultano ojačanje ali oddajanje prek vsaj dveh radiofrekvenčnih kanalov, ali ojačevalnik, ki pri uporabi z opremo za oddajanje omogoča hkraten prenos prek vsaj dveh radiofrekvenčnih kanalov. Ta dokument zajema naslednje vrste opreme:
• bazna postaja (oprema z antenskim priključkom, namenjena za uporabo na stalni lokaciji);
• mobilna postaja (oprema z antenskim priključkom, ki se običajno uporablja v vozilu ali prenosno);
• prenosne postaje:
a) z antenskim priključkom; ali
b) brez zunanjega antenskega priključka (vgrajene antene), vendar s stalnim ali začasnim notranjim 50-ohmskim radiofrekvenčnim (RF) konektorjem, ki omogoča dostop do izhoda oddajnika; in
• katera koli oprema, ki se lahko uporablja v kombinaciji s katero koli zgornjo opremo, ko je ta neposredno priključena na to opremo za ojačanje izhodnih signalov oddajnika vsaj dveh posameznih naprav.
Vrste opreme, ki jih ta dokument ne zajema:
• prenosna oprema brez zunanjega ali notranjega radiofrekvenčnega konektorja in brez možnosti namestitve začasnega notranjega 50-ohmskega radiofrekvenčnega konektorja;
• oprema, ki uporablja pasivne kombinirane rešitve, pri katerih vsak oddajnik, povezan s pasivnim kombiniranim sistemom, oddaja signal prek enega samega kanala, kot je opredeljeno v točki H.3 standarda ETSI EG 200 053 [i.2].
Te specifikacije se uporabljajo samo za oddajnik ali ojačevalnik oddajnika. Če je sprejemnik priključen na isto opremo, se uporabljajo tudi specifikacije za sprejemnik iz ustrezne specifikacije (sklici od [i.5] do [i.12]).
Te specifikacije ne vključujejo nujno vseh lastnosti, ki bi jih lahko potreboval uporabnik opreme, in ne predstavljajo nujno optimalnega delovanja.
Poleg tega dokumenta se za opremo na področju uporabe tega dokumenta lahko uporabljajo tudi drugi standardi EN, ki določajo tehnične zahteve v zvezi z bistvenimi zahtevami iz drugih delov 3. člena direktive o radijski opremi [i.3].

General Information

• Status: Published
• Publication Date: 02-Nov-2016
• ICS: 33.060.99 - Other equipment for radiocommunications
• ICS: 33.070.01 - Mobile services in general
• Technical Committee: MOC - Mobile Communications
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 24-Oct-2016
• Due Date: 29-Dec-2016
• Completion Date: 03-Nov-2016
• Directive: 1999/5/EC - Directive 1999/5/EC of the European Parliament and of the Council of 9 March 1999 on radio equipment and telecommunications terminal equipment and the mutual recognition of their conformity
• Directive: 2014/53/EU - Directive 2014/53/EU of The European Parliament and of the Council of 16 April 2014 on the harmonisation of the laws of the Member States relating to the making available on the market of radio equipment and repealing Directive 1999/5/EC
• Ref Project: ETSI EN 303 039 V2.1.2 (2016-10) - Land Mobile Service; Multichannel transmitter specification for the PMR Service; Harmonised Standard covering the essential requirements of article 3.2 of the Directive 2014/53/EU

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 303 039 V2.1.2:2016
01-december-2016
6WRULWHYNRSHQVNLKPRELOQLKNRPXQLNDFLM6SHFLILNDFLMDYHþNDQDOQHJDRGGDMQLND
]DVWRULWHY305+DUPRQL]LUDQLVWDQGDUGNL]DMHPDELVWYHQH]DKWHYHþOHQD
GLUHNWLYH(8
Land Mobile Service - Multichannel transmitter specification for the PMR Service -
Harmonised Standard covering the essential requirements of article 3.2 of the Directive
2014/53/EU
Ta slovenski standard je istoveten z: ETSI EN 303 039 V2.1.2 (2016-10)
ICS:
33.060.99 Druga oprema za radijske Other equipment for
komunikacije radiocommunications
33.070.01 Mobilni servisi na splošno Mobile services in general
SIST EN 303 039 V2.1.2:2016 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 303 039 V2.1.2:2016

---------------------- Page: 2 ----------------------

SIST EN 303 039 V2.1.2:2016
ETSI EN 303 039 V2.1.2 (2016-10)






HARMONISED EUROPEAN STANDARD
Land Mobile Service;
Multichannel transmitter specification for the PMR Service;
Harmonised Standard covering the essential requirements
of article 3.2 of the Directive 2014/53/EU

---------------------- Page: 3 ----------------------

SIST EN 303 039 V2.1.2:2016
 2 ETSI EN 303 039 V2.1.2 (2016-10)



Reference
REN/ERM-TGDMR-362
Keywords
data, mobile, PMR, radio

ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: [phone]  Fax: [phone]

Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88

Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.

© European Telecommunications Standards Institute 2016.
All rights reserved.

TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.
TM
3GPP and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI

---------------------- Page: 4 ----------------------

SIST EN 303 039 V2.1.2:2016
 3 ETSI EN 303 039 V2.1.2 (2016-10)
Contents
Intellectual Property Rights . 6
Foreword . 6
Modal verbs terminology . 6
1 Scope . 7
2 References . 8
2.1 Normative references . 8
2.2 Informative references . 8
3 Definitions, symbols and abbreviations . 9
3.1 Definitions . 9
3.2 Symbols . 11
3.3 Abbreviations . 11
4 General and operational requirements . 12
4.1 General . 12
4.1.0 Environmental profile . 12
4.1.1 Choice of model for testing . 12
4.1.1.0 General . 12
4.1.1.1 Auxiliary test equipment . 12
4.1.1.2 Declarations by the manufacturer . 13
4.2 Multi-Mode equipment . 13
4.3 Testing of equipment that does not have an external 50 Ω RF connector (integral antenna equipment) . 13
5 Test conditions, power sources and ambient temperatures . 13
5.1 Normal and extreme test conditions . 13
5.2 Test power source . 13
5.3 Normal test conditions . 14
5.3.1 Normal temperature and humidity . 14
5.3.2 Normal test power source . 14
5.3.2.1 Mains voltage . 14
5.3.2.2 Regulated lead-acid battery power sources used on vehicles . 14
5.3.2.3 Other power sources . 14
5.4 Extreme test conditions . 14
5.4.1 Extreme temperatures . 14
5.4.2 Extreme test source voltages . 14
5.4.2.1 Mains voltage . 14
5.4.2.2 Regulated lead-acid battery power sources used on vehicles . 15
5.4.2.3 Power sources using other types of batteries . 15
5.4.2.4 Other power sources . 15
5.5 Procedure for tests at extreme temperatures . 15
5.5.0 Thermal balance . 15
5.5.1 Procedure for equipment designed for continuous transmission. 15
5.5.2 Procedure for equipment designed for intermittent transmission . 15
6 General conditions of measurement . 16
6.1 Test bandwidth . 16
6.2 Test load (artificial antenna) . 16
6.3 Test signals (wanted and unwanted signals) . 16
6.3.0 General . 16
6.3.1 Transmitter test signals for digital transmissions . 16
6.3.2 Encoder for digital transmitter measurements . 17
6.3.3 Transmitter test signals for analogue transmissions . 17
6.3.3.0 General . 17
6.3.3.1 Test signals for frequency modulated channels. 17
6.3.3.2 Test signals for amplitude modulated channels. 17
6.3.3.3 Transmitter effective radiated power test signal (C1) . 17
6.4 Transceiver data interface for digital transmissions . 17
ETSI

---------------------- Page: 5 ----------------------

SIST EN 303 039 V2.1.2:2016
 4 ETSI EN 303 039 V2.1.2 (2016-10)
6.5 Impedance . 17
6.6 PEP . 18
6.7 Duplex equipment . 18
6.8 Modes of operation of the transmitter . 18
6.9 Measurement filter definition for digital transmissions . 18
6.10 Test site and general arrangements for measurements involving the use of radiated fields . 18
7 Technical characteristics of the transmitter . 19
7.1 Transmitter output power (conducted) . 19
7.1.0 General . 19
7.1.1 Definitions . 19
7.1.2 Method of measurement . 19
7.1.3 Limits . 19
7.2 Adjacent and alternate channel power . 20
7.2.1 Definition . 20
7.2.2 Method of measurement . 21
7.2.3 Limits . 23
7.3 Unwanted emissions . 24
7.3.1 Definition . 24
7.3.2 Method of measuring the power level . 25
7.3.2.1 Measurement options . 25
7.3.2.2 Method of measuring conducted spurious emissions (clause 7.3.2.1 a)) . 25
7.3.2.3 Method of measuring the effective radiated power (clause 7.3.2.1 b)) . 26
7.3.2.4 Method of measuring wideband noise. 27
7.3.2.5 Method for measuring frequency conversion oscillator conducted spurious emissions. 28
7.3.2.6 Method for measuring third order intermodulation products between wanted channels . 29
7.3.3 Limits . 29
7.3.3.1 Spurious emissions power . 29
7.3.3.2 Wideband noise power . 30
7.3.3.3 Frequency conversion oscillator spurious emission . 31
7.3.3.4 Third order intermodulation product spurious emission . 31
7.4 Intermodulation attenuation. 32
7.4.0 Applicability . 32
7.4.1 Definition . 32
7.4.2 Method of measurement . 32
7.4.3 Limits . 33
7.5 Transient power measurements . 33
7.5.1 Definition . 33
7.5.2 Method of Measurement . 33
7.5.3 Limits . 34
8 Testing for compliance with technical requirements . 34
8.1 Test conditions, power supply and ambient temperatures . 34
8.2 Interpretation of the measurement results . 35
Annex A (normative): Relationship between the present document and the essential
requirements of Directive 2014/53/EU . 36
Annex B (normative): Radiated measurement . 37
B.1 Test sites and general arrangements for measurements involving the use of radiated fields . 37
B.1.0 General . 37
B.1.1 Anechoic chamber . 37
B.1.2 Anechoic chamber with a conductive ground plane . 38
B.1.3 Open Area Test Site (OATS) . 39
B.1.4 Test antenna . 40
B.1.5 Substitution antenna . 40
B.1.6 Measuring antenna . 41
B.2 Guidance on the use of radiation test sites . 41
B.2.0 General . 41
B.2.1 Verification of the test site . 41
B.2.2 Preparation of the EUT . 41
ETSI

---------------------- Page: 6 ----------------------

SIST EN 303 039 V2.1.2:2016
 5 ETSI EN 303 039 V2.1.2 (2016-10)
B.2.3 Power supplies to the EUT . 41
B.2.4 Range length . 41
B.2.5 Site preparation . 42
B.3 Coupling of signals . 43
B.3.0 General . 43
B.3.1 Data signals . 43
Annex C (normative): Specification for some particular measurement arrangements . 44
C.1 Spectrum analyser specification . 44
C.1.1 Adjacent and alternate channel power measurement . 44
C.1.2 Unwanted emissions measurement . 44
C.2 Integrating and power summing device . 45
Annex D (informative): Change History . 46
History . 47

ETSI

---------------------- Page: 7 ----------------------

SIST EN 303 039 V2.1.2:2016
 6 ETSI EN 303 039 V2.1.2 (2016-10)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (https://ipr.etsi.org/).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This Harmonised European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic
compatibility and Radio spectrum Matters (ERM).
The present document has been prepared under the Commission's standardisation request C(2015) 5376 final [i.4] to
provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation
of the laws of the Member States relating to the making available on the market of radio equipment and repealing
Directive 1999/5/EC [i.3].
Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with
the normative clauses of the present document given in table A.1 confers, within the limits of the scope of the present
document, a presumption of conformity with the corresponding essential requirements of that Directive, and associated
EFTA regulations.

National transposition dates
Date of latest announcement of this EN (doa): 31 January 2016
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 31 July 2017
Date of withdrawal of any conflicting National Standard (dow): 31 July 2018

Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.

ETSI

---------------------- Page: 8 ----------------------

SIST EN 303 039 V2.1.2:2016
 7 ETSI EN 303 039 V2.1.2 (2016-10)
1 Scope
The present document covers the technical requirements for multiple channel radio transmitters used in stations in the
Private Mobile Radio (PMR) service.
It applies to use in the land mobile service, operating on radio frequencies between 30 MHz and 3 GHz, with channel
separations of < 10 kHz, 12,5 kHz, 20 kHz, 25 kHz, 50 kHz, 100 kHz and 150 kHz.
Table 1: Radiocommunications service frequency bands
Radiocommunications service frequency bands
Transmit 30 MHz to 3 000 MHz

It applies to equipment for continuous and/or discontinuous transmission of data and/or digital speech and/or analogue
speech and using constant envelope or non-constant envelope modulation.
The equipment comprises a transmitter capable of simultaneous amplification or transmission on two or more RF
channels, or an amplifier which when operated with transmitter equipment provides simultaneous transmission on two
or more RF channels. The types of equipment covered by the present document are as follows:
• base station (equipment fitted with an antenna connector, intended for use in a fixed location);
• mobile station (equipment fitted with an antenna connector, normally used in a vehicle or as a transportable);
• those hand portable stations:
a) fitted with an antenna connector; or
b) without an external antenna connector (integral antenna equipment), but fitted with a permanent internal
or a temporary internal 50 Ω Radio Frequency (RF) connector which allows access to the transmitter
output; and
• any equipment that may be used in combination with any of the above equipments when directly connected to
those equipments for the amplification of the transmitter output signals of two or more individual equipments.
Types of equipment not covered by the present document are as follows:
• hand portable equipment without an external or internal RF connector and without the possibility of having a
temporary internal 50 Ω RF connector is not covered by the present document;
• any equipment using passive combining solutions where each transmitter connected to the passive combining
system transmits on a single channel, as detailed in ETSI EG 200 053 [i.2], clause H.3.
These specifications apply to the transmitter or transmitter amplifier only. If a receiver is fitted to the same equipment,
the receiver specifications in the relevant specification (references [i.5] to [i.12]) also apply.
These specifications do not necessarily include all the characteristics that may be required by a user of equipment, nor
do they necessarily represent the optimum performance achievable.
In addition to the present document, other ENs that specify technical requirements in respect of essential requirements
under other parts of article 3 of the Radio Equipment Directive [i.3] may apply to equipment within the scope of the
present document.
ETSI

---------------------- Page: 9 ----------------------

SIST EN 303 039 V2.1.2:2016
 8 ETSI EN 303 039 V2.1.2 (2016-10)
2 References
2.1 Normative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
http://docbox.etsi.org/Reference.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are necessary for the application of the present document.
[1] Recommendation ITU-T O.153 (10-1992): "Basic parameters for the measurement of error
performance at bit rates below the primary rate".
[2] Void.
[3] ETSI TR 102 273 (V1.2.1) (12-2001) (all parts): "Electromagnetic compatibility and Radio
spectrum Matters (ERM); Improvement on Radiated Methods of Measurement (using test site) and
evaluation of the corresponding measurement uncertainties".
[4] ANSI C63.5 (2006): "American National Standard for Electromagnetic Compatibility-Radiated
Emission Measurements in Electromagnetic Interference (EMI) Control-Calibration of Antennas
(9 kHz to 40 GHz)".
2.2 Infor
...

ETSI EN 303 039 V2.1.2 (2016-10)






HARMONISED EUROPEAN STANDARD
Land Mobile Service;
Multichannel transmitter specification for the PMR Service;
Harmonised Standard covering the essential requirements
of article 3.2 of the Directive 2014/53/EU

---------------------- Page: 1 ----------------------
2 ETSI EN 303 039 V2.1.2 (2016-10)



Reference
REN/ERM-TGDMR-362
Keywords
data, mobile, PMR, radio

ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: [phone]  Fax: [phone]

Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88

Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.

© European Telecommunications Standards Institute 2016.
All rights reserved.

TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.
TM
3GPP and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI

---------------------- Page: 2 ----------------------
3 ETSI EN 303 039 V2.1.2 (2016-10)
Contents
Intellectual Property Rights . 6
Foreword . 6
Modal verbs terminology . 6
1 Scope . 7
2 References . 8
2.1 Normative references . 8
2.2 Informative references . 8
3 Definitions, symbols and abbreviations . 9
3.1 Definitions . 9
3.2 Symbols . 11
3.3 Abbreviations . 11
4 General and operational requirements . 12
4.1 General . 12
4.1.0 Environmental profile . 12
4.1.1 Choice of model for testing . 12
4.1.1.0 General . 12
4.1.1.1 Auxiliary test equipment . 12
4.1.1.2 Declarations by the manufacturer . 13
4.2 Multi-Mode equipment . 13
4.3 Testing of equipment that does not have an external 50 Ω RF connector (integral antenna equipment) . 13
5 Test conditions, power sources and ambient temperatures . 13
5.1 Normal and extreme test conditions . 13
5.2 Test power source . 13
5.3 Normal test conditions . 14
5.3.1 Normal temperature and humidity . 14
5.3.2 Normal test power source . 14
5.3.2.1 Mains voltage . 14
5.3.2.2 Regulated lead-acid battery power sources used on vehicles . 14
5.3.2.3 Other power sources . 14
5.4 Extreme test conditions . 14
5.4.1 Extreme temperatures . 14
5.4.2 Extreme test source voltages . 14
5.4.2.1 Mains voltage . 14
5.4.2.2 Regulated lead-acid battery power sources used on vehicles . 15
5.4.2.3 Power sources using other types of batteries . 15
5.4.2.4 Other power sources . 15
5.5 Procedure for tests at extreme temperatures . 15
5.5.0 Thermal balance . 15
5.5.1 Procedure for equipment designed for continuous transmission. 15
5.5.2 Procedure for equipment designed for intermittent transmission . 15
6 General conditions of measurement . 16
6.1 Test bandwidth . 16
6.2 Test load (artificial antenna) . 16
6.3 Test signals (wanted and unwanted signals) . 16
6.3.0 General . 16
6.3.1 Transmitter test signals for digital transmissions . 16
6.3.2 Encoder for digital transmitter measurements . 17
6.3.3 Transmitter test signals for analogue transmissions . 17
6.3.3.0 General . 17
6.3.3.1 Test signals for frequency modulated channels. 17
6.3.3.2 Test signals for amplitude modulated channels. 17
6.3.3.3 Transmitter effective radiated power test signal (C1) . 17
6.4 Transceiver data interface for digital transmissions . 17
ETSI

---------------------- Page: 3 ----------------------
4 ETSI EN 303 039 V2.1.2 (2016-10)
6.5 Impedance . 17
6.6 PEP . 18
6.7 Duplex equipment . 18
6.8 Modes of operation of the transmitter . 18
6.9 Measurement filter definition for digital transmissions . 18
6.10 Test site and general arrangements for measurements involving the use of radiated fields . 18
7 Technical characteristics of the transmitter . 19
7.1 Transmitter output power (conducted) . 19
7.1.0 General . 19
7.1.1 Definitions . 19
7.1.2 Method of measurement . 19
7.1.3 Limits . 19
7.2 Adjacent and alternate channel power . 20
7.2.1 Definition . 20
7.2.2 Method of measurement . 21
7.2.3 Limits . 23
7.3 Unwanted emissions . 24
7.3.1 Definition . 24
7.3.2 Method of measuring the power level . 25
7.3.2.1 Measurement options . 25
7.3.2.2 Method of measuring conducted spurious emissions (clause 7.3.2.1 a)) . 25
7.3.2.3 Method of measuring the effective radiated power (clause 7.3.2.1 b)) . 26
7.3.2.4 Method of measuring wideband noise. 27
7.3.2.5 Method for measuring frequency conversion oscillator conducted spurious emissions. 28
7.3.2.6 Method for measuring third order intermodulation products between wanted channels . 29
7.3.3 Limits . 29
7.3.3.1 Spurious emissions power . 29
7.3.3.2 Wideband noise power . 30
7.3.3.3 Frequency conversion oscillator spurious emission . 31
7.3.3.4 Third order intermodulation product spurious emission . 31
7.4 Intermodulation attenuation. 32
7.4.0 Applicability . 32
7.4.1 Definition . 32
7.4.2 Method of measurement . 32
7.4.3 Limits . 33
7.5 Transient power measurements . 33
7.5.1 Definition . 33
7.5.2 Method of Measurement . 33
7.5.3 Limits . 34
8 Testing for compliance with technical requirements . 34
8.1 Test conditions, power supply and ambient temperatures . 34
8.2 Interpretation of the measurement results . 35
Annex A (normative): Relationship between the present document and the essential
requirements of Directive 2014/53/EU . 36
Annex B (normative): Radiated measurement . 37
B.1 Test sites and general arrangements for measurements involving the use of radiated fields . 37
B.1.0 General . 37
B.1.1 Anechoic chamber . 37
B.1.2 Anechoic chamber with a conductive ground plane . 38
B.1.3 Open Area Test Site (OATS) . 39
B.1.4 Test antenna . 40
B.1.5 Substitution antenna . 40
B.1.6 Measuring antenna . 41
B.2 Guidance on the use of radiation test sites . 41
B.2.0 General . 41
B.2.1 Verification of the test site . 41
B.2.2 Preparation of the EUT . 41
ETSI

---------------------- Page: 4 ----------------------
5 ETSI EN 303 039 V2.1.2 (2016-10)
B.2.3 Power supplies to the EUT . 41
B.2.4 Range length . 41
B.2.5 Site preparation . 42
B.3 Coupling of signals . 43
B.3.0 General . 43
B.3.1 Data signals . 43
Annex C (normative): Specification for some particular measurement arrangements . 44
C.1 Spectrum analyser specification . 44
C.1.1 Adjacent and alternate channel power measurement . 44
C.1.2 Unwanted emissions measurement . 44
C.2 Integrating and power summing device . 45
Annex D (informative): Change History . 46
History . 47

ETSI

---------------------- Page: 5 ----------------------
6 ETSI EN 303 039 V2.1.2 (2016-10)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (https://ipr.etsi.org/).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This Harmonised European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic
compatibility and Radio spectrum Matters (ERM).
The present document has been prepared under the Commission's standardisation request C(2015) 5376 final [i.4] to
provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation
of the laws of the Member States relating to the making available on the market of radio equipment and repealing
Directive 1999/5/EC [i.3].
Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with
the normative clauses of the present document given in table A.1 confers, within the limits of the scope of the present
document, a presumption of conformity with the corresponding essential requirements of that Directive, and associated
EFTA regulations.

National transposition dates
Date of latest announcement of this EN (doa): 31 January 2016
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 31 July 2017
Date of withdrawal of any conflicting National Standard (dow): 31 July 2018

Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.

ETSI

---------------------- Page: 6 ----------------------
7 ETSI EN 303 039 V2.1.2 (2016-10)
1 Scope
The present document covers the technical requirements for multiple channel radio transmitters used in stations in the
Private Mobile Radio (PMR) service.
It applies to use in the land mobile service, operating on radio frequencies between 30 MHz and 3 GHz, with channel
separations of < 10 kHz, 12,5 kHz, 20 kHz, 25 kHz, 50 kHz, 100 kHz and 150 kHz.
Table 1: Radiocommunications service frequency bands
Radiocommunications service frequency bands
Transmit 30 MHz to 3 000 MHz

It applies to equipment for continuous and/or discontinuous transmission of data and/or digital speech and/or analogue
speech and using constant envelope or non-constant envelope modulation.
The equipment comprises a transmitter capable of simultaneous amplification or transmission on two or more RF
channels, or an amplifier which when operated with transmitter equipment provides simultaneous transmission on two
or more RF channels. The types of equipment covered by the present document are as follows:
• base station (equipment fitted with an antenna connector, intended for use in a fixed location);
• mobile station (equipment fitted with an antenna connector, normally used in a vehicle or as a transportable);
• those hand portable stations:
a) fitted with an antenna connector; or
b) without an external antenna connector (integral antenna equipment), but fitted with a permanent internal
or a temporary internal 50 Ω Radio Frequency (RF) connector which allows access to the transmitter
output; and
• any equipment that may be used in combination with any of the above equipments when directly connected to
those equipments for the amplification of the transmitter output signals of two or more individual equipments.
Types of equipment not covered by the present document are as follows:
• hand portable equipment without an external or internal RF connector and without the possibility of having a
temporary internal 50 Ω RF connector is not covered by the present document;
• any equipment using passive combining solutions where each transmitter connected to the passive combining
system transmits on a single channel, as detailed in ETSI EG 200 053 [i.2], clause H.3.
These specifications apply to the transmitter or transmitter amplifier only. If a receiver is fitted to the same equipment,
the receiver specifications in the relevant specification (references [i.5] to [i.12]) also apply.
These specifications do not necessarily include all the characteristics that may be required by a user of equipment, nor
do they necessarily represent the optimum performance achievable.
In addition to the present document, other ENs that specify technical requirements in respect of essential requirements
under other parts of article 3 of the Radio Equipment Directive [i.3] may apply to equipment within the scope of the
present document.
ETSI

---------------------- Page: 7 ----------------------
8 ETSI EN 303 039 V2.1.2 (2016-10)
2 References
2.1 Normative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
http://docbox.etsi.org/Reference.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are necessary for the application of the present document.
[1] Recommendation ITU-T O.153 (10-1992): "Basic parameters for the measurement of error
performance at bit rates below the primary rate".
[2] Void.
[3] ETSI TR 102 273 (V1.2.1) (12-2001) (all parts): "Electromagnetic compatibility and Radio
spectrum Matters (ERM); Improvement on Radiated Methods of Measurement (using test site) and
evaluation of the corresponding measurement uncertainties".
[4] ANSI C63.5 (2006): "American National Standard for Electromagnetic Compatibility-Radiated
Emission Measurements in Electromagnetic Interference (EMI) Control-Calibration of Antennas
(9 kHz to 40 GHz)".
2.2 Informative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are not necessary for the application of the present document but they assist the
user with regard to a particular subject area.
[i.1] CEPT/ERC/REC 74-01 (2011): "Unwanted Emissions in the Spurious domain".
[i.2] ETSI EG 200 053: "Electromagnetic compatibility and Radio spectrum Matters (ERM); Radio site
engineering for radio equipment and systems".
[i.3] Directive 2014/53/EU of the European Parliament and of the Council of 16 April 2014 on the
harmonisation of the laws of the Member States relating to the making available on the market of
radio equipment and repealing Directive 1999/5/EC.
NOTE: Article 3.2 and article 10.8.
[i.4] Commission Implementing Decision C(2015) 5376 final of 4.8
...