SIST EN 2703:2005

Aerospace series - Aluminium alloy AL-P2024-T4 or T42 - Clad sheet and strip - 0,3 mm <a <6 mm

This standard specifies the requirements relating to:
Aluminium alloy AL-P2024-
T4 or T42
Clad sheet and strip
0,3 mm < a < 6 mm
for aerospace application.

Luft- und Raumfahrt - Aluminiumlegierung AL-P2024-T4 oder T42 - Bleche und Bänder, plattiert - 0,3 mm <a <6 mm

Diese Norm legt die Anforderungen an
Aluminiumlegierung AL-P2024-
T4 oder T42
Bleche und Bänder, plattiert
0,3 mm  a  6 mm
für Anwendungen in der Luft- und Raumfahrt fest.

Série aérospatiale - Alliage d'aluminium AL-P2024-T4 ou T42 - Tôles et bandes plaquées - 0,3 mm <a <6 mm

Aerospace series - Aluminium alloy AL-P2024-T4 or T42 - Clad sheet and strip - 0,3 mm <a <6 mm

General Information

• Status: Published
• Publication Date: 31-Oct-2005
• ICS: 49.025.20 - Aluminium
• Technical Committee: SS SPL - Technical Board for the general field
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 01-Nov-2005
• Due Date: 01-Nov-2005
• Completion Date: 01-Nov-2005
• Ref Project: EN 2703:2005 - Aerospace series - Aluminium alloy AL-P2024-T4 or T42 - Clad sheet and strip - 0,3 mm <a <6 mm

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 2703:2005
01-november-2005
Aerospace series - Aluminium alloy AL-P2024-T4 or T42 - Clad sheet and strip - 0,3
mm Aerospace series - Aluminium alloy AL-P2024-T4 or T42 - Clad sheet and strip - 0,3 mm
Luft- und Raumfahrt - Aluminiumlegierung AL-P2024-T4 oder T42 - Bleche und Bänder,
plattiert - 0,3 mm Série aérospatiale - Alliage d'aluminium AL-P2024-T4 ou T42 - Tôles et bandes
plaquées - 0,3 mm Ta slovenski standard je istoveten z: EN 2703:2005
ICS:
49.025.20 Aluminij Aluminium
SIST EN 2703:2005 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 2703:2005

---------------------- Page: 2 ----------------------

SIST EN 2703:2005



EUROPEAN STANDARD EN 2703

NORME EUROPÉENNE

EUROPÄISCHE NORM
June 2005
ICS 49.025.20
English version
Aerospace series - Aluminium alloy AL-P2024-T4 or T42 - Clad
sheet and strip - 0,3 mm ≤≤≤≤a ≤≤≤≤6 mm
Série aérospatiale - Alliage d'aluminium AL-P2024-T4 ou Luft- und Raumfahrt - Aluminiumlegierung AL-P2024-T4
T42 - Tôles et bandes plaquées - 0,3 mm ≤a ≤6 mm oder T42 - Bleche und Bänder, plattiert - 0,3 mm ≤a ≤6 mm
This European Standard was approved by CEN on 22 April 2005.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Central Secretariat or to any CEN member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official
versions.

CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,
Slovenia, Spain, Sweden, Switzerland and United Kingdom.




EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2005 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 2703:2005: E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN 2703:2005
EN 2703:2005 (E)
Foreword
This document (EN 2703:2005) has been prepared by the European Association of Aerospace
Manufacturers - Standardization (AECMA-STAN).
After enquiries and votes carried out in accordance with the rules of this Association, this Standard has
received the approval of the National Associations and the Official Services of the member countries of
AECMA, prior to its presentation to CEN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by December 2005, and conflicting national standards shall be withdrawn
at the latest by December 2005.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland
and the United Kingdom.
2

---------------------- Page: 4 ----------------------

SIST EN 2703:2005
EN 2703:2005 (E)
Introduction
This standard is part of the
...