oSIST prEN ISO 1288-3:2014

Glass in building - Determination of the bending strength of glass - Part 3: Test with specimen supported at two points (four-point bending) (ISO/DIS 1288-3:2014)

Verre dans la construction - Détermination de la résistance du verre à la flexion - Partie 3: Essais avec éprouvettes supportées en deux points (flexion quatre points)

Glas im Bauwesen - Bestimmung der Biegefestigkeit von Glas - Teil 3: Prüfung von Proben bei zweiseitiger Auflagerung (Vierschneiden-Verfahren) (ISO/DIS 1288-3:2014)

Diese Internationale Norm legt ein Verfahren zur Bestimmung der Biegefestigkeit von Flachglas im Bauwesen unter Einschluss der Glaskanten fest. Das festgelegte Verfahren kann auch nur zur Bestimmung der Biegefestigkeit der Glaskanten angewendet werden.
Die Grenzen der Anwendbarkeit dieses Teiles der Norm sind in  ISO 1288 1 beschrieben.
ISO 1288 1 sollte in Verbindung mit diesem Teil der Norm gelesen werden.

Verre dans la construction - Détermination de la résistance du verre à la flexion - Partie 3: Essais avec éprouvettes supportées en deux points (flexion quatre points) (ISO/DIS 1288-3:2014)

Steklo v gradbeništvu - Ugotavljanje upogibne trdnosti stekla - 3. del: Preskušanje dvakrat podprtega vzorca (štiritočkovna obremenitev) (ISO/DIS 1288-3:2014)

General Information

• Status: Not Published
• Public Enquiry End Date: 29-Apr-2014
• ICS: 81.040.20 - Glass in building
• Technical Committee: STV - Steklo, svetloba in razsvetljava v gradbeništvu
• Current Stage: 98 - Abandoned project (Adopted Project)
• Start Date: 29-Aug-2016
• Due Date: 03-Sep-2016
• Completion Date: 29-Aug-2016
• Ref Project: prEN 1288-3 rev - Glass in building - Determination of the bending strength of glass - Part 3: Test with specimen supported at two points (four-point bending) (ISO/DIS 1288-3:2014)

Relations

• Revised: SIST EN 1288-3:2001 - Glass in building - Determination of the bending strength of glass - Part 3: Test with specimen supported at two points (four point bending)
• Effective Date: 01-Apr-2014
• Revised: SIST EN 1288-3:2001 - Glass in building - Determination of the bending strength of glass - Part 3: Test with specimen supported at two points (four point bending)
• Effective Date: 18-Jan-2023
• Revised: SIST EN 1288-3:2001 - Glass in building - Determination of the bending strength of glass - Part 3: Test with specimen supported at two points (four point bending)
• Effective Date: 19-Jan-2023

Standards Content (Sample)

SLOVENSKI STANDARD
oSIST prEN ISO 1288-3:2014
01-april-2014
6WHNORYVWDYEDK8JRWDYOMDQMHXSRJLEQHWUGQRVWLVWHNODGHO3UHVNXãDQMH
GYDNUDWSRGSUWHJDY]RUFDãWLULWRþNRYQDREUHPHQLWHY,62',6
Glass in building - Determination of the bending strength of glass - Part 3: Test with
specimen supported at two points (four-point bending) (ISO/DIS 1288-3:2014)
Glas im Bauwesen - Bestimmung der Biegefestigkeit von Glas - Teil 3: Prüfung von
Proben bei zweiseitiger Auflagerung (Vierschneiden-Verfahren) (ISO/DIS 1288-3:2014)
Verre dans la construction - Détermination de la résistance du verre à la flexion - Partie
3: Essais avec éprouvettes supportées en deux points (flexion quatre points) (ISO/DIS
1288-3:2014)
Ta slovenski standard je istoveten z: prEN ISO 1288-3 rev
ICS:
81.040.20 Steklo v gradbeništvu Glass in building
oSIST prEN ISO 1288-3:2014 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN ISO 1288-3:2014

---------------------- Page: 2 ----------------------
oSIST prEN ISO 1288-3:2014
DRAFT INTERNATIONAL STANDARD
ISO/DIS 1288-3
ISO/TC 160/SC 2 Secretariat: ANSI
Voting begins on: Voting terminates on:
2014-01-09 2014-06-09
Glass in building — Determination of the bending strength
of glass —
Part 3:
Test with specimen supported at two points (four-point
bending)
Verre dans la construction — Détermination de la résistance du verre à la flexion —
Partie 3: Essais avec éprouvettes supportées en deux points (flexion quatre points)
ICS: 81.040.20
ISO/CEN PARALLEL PROCESSING
This draft has been developed within the International Organization for
Standardization (ISO), and processed under the ISO lead mode of collaboration
as defined in the Vienna Agreement.
This draft is hereby submitted to the ISO member bodies and to the CEN member
bodies for a parallel five month enquiry.
Should this draft be accepted, a final draft, established on the basis of comments
received, will be submitted to a parallel two-month approval vote in ISO and
THIS DOCUMENT IS A DRAFT CIRCULATED
formal vote in CEN.
FOR COMMENT AND APPROVAL. IT IS
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
To expedite distribution, this document is circulated as received from the
IN ADDITION TO THEIR EVALUATION AS
committee secretariat. ISO Central Secretariat work of editing and text
BEING ACCEPTABLE FOR INDUSTRIAL,
composition will be undertaken at publication stage.
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO/DIS 1288-3:2013(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
©
PROVIDE SUPPORTING DOCUMENTATION. ISO 2013

---------------------- Page: 3 ----------------------
oSIST prEN ISO 1288-3:2014
ISO/DIS 1288-3:2013(E)

Copyright notice
This ISO document is a Draft International Standard and is copyright-protected by ISO. Except as
permitted under the applicable laws of the user’s country, neither this ISO draft nor any extract
from it may be reproduced, stored in a retrieval system or transmitted in any form or by any means,
electronic, photocopying, recording or otherwise, without prior written permission being secured.
Requests for permission to reproduce should be addressed to either ISO at the address below or ISO’s
member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail [e-mail]
Web www.iso.org
Reproduction may be subject to royalty payments or a licensing agreement.
Violators may be prosecuted.
ii © ISO 2013 – All rights reserved

---------------------- Page: 4 ----------------------
oSIST prEN ISO 1288-3:2014
FDIS 1288-3
Contents
Foreword
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Symbols (and abbreviated terms) . 2
5 Apparatus . 2
5.1 Testing machine . 2
5.2 Measuring instruments . 3
6 Sample . 3
6.1 Number of specimens . 3
6.2 Specimen dimensions . 3
6.3 Specimen condition and treatment . 3
6.4 Adhesive film . 4
7 Procedure . 4
7.1 Measuring width and thickness of each specimen . 4
7.2 Bending test . 5
8 Evaluation . 5
8.1 General. 5
8.2 Bending strength of the surface area, edges included . 5
8.3 Bending strength of the edges . 5
9 Test report . 6

© ISO 2011 – All rights reserved iii

---------------------- Page: 5 ----------------------
oSIST prEN ISO 1288-3:2014
FDIS 1288-3
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO
member bodies). The work of preparing International Standards is normally carried out through ISO technical
committees. Each member body interested in a subject for which a technical committee has been established has
the right to be represented on that committee. International organizations, governmental and non-governmental, in
liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical
Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3.
Draft International Standards adopted by the technical committees are circulated to the member bodies for voting.
Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this part of ISO 1288 may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
International Standard ISO 1288-3 was prepared by Technical Committee ISO/TC 160, Glass in building,
Subcommittee SC 2, Use considerations in conjunction with Technical Committee CEN/TC 129, Glass in building.
ISO 1288 consists of the following parts, under the general title Glass in building — Determination of the bending
strength of glass:
 Part 1: Fundamentals of testing glass
 Part 2: Coaxial double ring test on flat specimens with large test surface areas
 Part 3: Test with specimen supported at two points (four point bending)
 Part 4: Testing of channel shaped glass
 Part 5: Coaxial double ring test on flat specimens with small test surface areas
This Standard has been based on EN 1288-3 Glass in building - Determination of the bending strength of glass" -
Part 3 : Test with specimen supported at two points (four point bending) prepared by Technical Committee
CEN/TC 129 "Glass in building"/WG8 "Mechanical Strength".
According to the CEN/CENELEC Internal Regulations, the national standards organisations of the following
countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland,
France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden,
Switzerland and the United Kingdom.

iv © ISO 2011 – All rights reserved

---------------------- Page: 6 ----------------------
oSIST prEN ISO 1288-3:2014
FDIS FDIS 1288-3

Glass in building — Determination of the bending strength of
glass — Part 3: Test with specimen supported at two points (four
point bending)
1 Scope
This International Standard specifies a method for determining the bending strength, including the effects of the
edges, of flat glass for use in building. The method specified can also be used to determine the bending strength
of the edges of glass separately.
The limitations of this part of this International Standard are described in ISO 1288-1.
ISO 1288-1 should be read in conjunction with this part of this International Standard.
2 Normative references
The following normative documents contain provisions which, through reference in this text, constitute provisions of
this part of ISO 1288. For dated references, subsequent amendments to, or revisions of, any of these publications
do not apply. However, parties to agreements based on this part of ISO 1288 are encouraged to investigate the
possibility of applying the most recent editions of the normative documents indicated below. For undated
references, the latest edition of the normative document referred to applies. Members of ISO and IEC maintain
registers of currently valid International Standards.
ISO 48, Rubber, vu
...