kSIST FprEN ISO 13670:2025
(Main)Fasteners - Reverse-taper grooved pins - One quarter-length progressive grooves on both sides (ISO/FDIS 13670:2025)
Fasteners - Reverse-taper grooved pins - One quarter-length progressive grooves on both sides (ISO/FDIS 13670:2025)
This document specifies the characteristics of reverse-taper grooved pins with one quarter-length progressive grooves on both sides (with closed ends), in steel and stainless steel, and with nominal diameters 2 mm to 25 mm.
These grooved pins are designed to fulfil the main following functions:
— relative rotation of the assembled parts,
— locking of two (or more) parts
with an easy installation (due to its symmetrical shape) and a medium level of pull-out resistance (due to the elastic fit behaviour of the pin).
The general requirements (including functional principles for grooved pins and assembly) are specified in ISO 13669.
Befestigungselemente - Gegenläufige Rillenstifte - Progressive Rillen von einem Viertel der Länge auf beiden Seiten (ISO/FDIS 13670:2025)
Dieses Dokument legt die Eigenschaften von gegenläufigen Kerbstiften mit progressiven Kerben von einem Viertel der Länge auf beiden Seiten (mit geschlossenen Enden) aus Stahl und nichtrostendem Stahl und mit einem Nenndurchmesser 2 mm bis 25 mm fest.
Diese Kerbstifte sind so ausgelegt, dass sie die folgenden Hauptfunktionen ausführen:
die relative Drehung der zusammengebauten Teile; und
zwei (oder mehr) Teile kraftschlüssig miteinander verbinden,
mit einem einfachen Einbau (durch deren symmetrische Form) und mit mittlerer Auszugsfestigkeit (durch das elastische Passverhalten des Stifts).
Die allgemeinen Anforderungen (einschließlich Grundlagen hinsichtlich der Funktion für Kerbstifte und Zusammenbau) sind in ISO 13669 festgelegt.
Fixations - Goupilles cannelées inversées - Cannelures progressives sur le quart de la longueur à chaque extrémité (ISO/FDIS 13670:2025)
Le présent document spécifie les caractéristiques des goupilles cannelées inversées à cannelures progressives sur le quart de la longueur à chaque extrémité (non-débouchantes), en acier et en acier inoxydable, et de diamètre nominal 2 mm à 25 mm.
Ces goupilles cannelées sont conçues pour remplir les fonctions principales suivantes:
— rotation relative des pièces assemblées,
— solidarisation de deux (ou plusieurs) pièces
avec une installation facile (du fait de sa forme symétrique) et une résistance modérée à l'extraction (du fait du comportement par ajustement élastique de la goupille dans son trou).
Les exigences générales (incluant les principes fonctionnels des goupilles cannelées et leur assemblage) sont spécifiées dans l'ISO 13669.
Vezni elementi - Povratni zasekani zatiči - Postopni obojestranski zatiči dolžine ene četrtine celotne dolžine (ISO/FDIS 13670:2025)
General Information
Standards Content (Sample)
SLOVENSKI STANDARD
oSIST prEN ISO 13670:2024
01-februar-2024
Vezni elementi - Povratni zasekani zatiči - Postopni obojestranski zatiči dolžine
ene četrtine celotne dolžine (ISO/DIS 13670:2023)
Fasteners - Reverse-taper grooved pins - One quarter-length progressive grooves on
both sides (ISO/DIS 13670:2023)
Befestigungselemente - Gegenläufige Rillenstifte - Progressive Rillen von einem Viertel
der Länge auf beiden Seiten (ISO/DIS 13670:2023)
Fixations - Goupilles cannelées inversées - Cannelures progressives sur le quart de la
longueur à chaque extrémité (ISO/DIS 13670:2023)
Ta slovenski standard je istoveten z: prEN ISO 13670
ICS:
21.060.50 Zatiči, žeblji Pins, nails
oSIST prEN ISO 13670:2024 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
oSIST prEN ISO 13670:2024
oSIST prEN ISO 13670:2024
DRAFT INTERNATIONAL STANDARD
ISO/DIS 13670
ISO/TC 2 Secretariat: DIN
Voting begins on: Voting terminates on:
2023-11-30 2024-02-22
Fasteners — Reverse-taper grooved pins — One quarter-
length progressive grooves on both sides
Fixations — Goupilles cannelées inversées — Cannelures progressives sur le quart de la longueur à chaque
extrémité
ICS: 21.060.50
This document is circulated as received from the committee secretariat.
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENT AND APPROVAL. IT IS
ISO/CEN PARALLEL PROCESSING
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO/DIS 13670:2023(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
PROVIDE SUPPORTING DOCUMENTATION. © ISO 2023
oSIST prEN ISO 13670:2024
ISO/DIS 13670:2023(E)
DRAFT INTERNATIONAL STANDARD
ISO/DIS 13670
ISO/TC 2 Secretariat: DIN
Voting begins on: Voting terminates on:
Fasteners — Reverse-taper grooved pins — One quarter-
length progressive grooves on both sides
Fixations — Goupilles cannelées inversées — Cannelures progressives sur le quart de la longueur à chaque
extrémité
ICS: 21.060.50
This document is circulated as received from the committee secretariat.
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENT AND APPROVAL. IT IS
© ISO 2023
ISO/CEN PARALLEL PROCESSING
THEREFORE SUBJECT TO CHANGE AND MAY
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
NOT BE REFERRED TO AS AN INTERNATIONAL
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on STANDARD UNTIL PUBLISHED AS SUCH.
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
IN ADDITION TO THEIR EVALUATION AS
or ISO’s member body in the country of the requester. BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
ISO copyright office
USER PURPOSES, DRAFT INTERNATIONAL
CP 401 • Ch. de Blandonnet 8
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
CH-1214 Vernier, Geneva
POTENTIAL TO BECOME STANDARDS TO
Phone: +41 22 749 01 11
WHICH REFERENCE MAY BE MADE IN
Reference number
Email: copyright@iso.org
NATIONAL REGULATIONS.
Website: www.iso.org ISO/DIS 13670:2023(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
Published in Switzerland
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
ii
PROVIDE SUPPORTING DOCUMENTATION. © ISO 2023
oSIST prEN ISO 13670:2024
ISO/DIS 13670:2023(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Principles of grooved pins and assembly . 2
5 Dimensions .2
6 Requirements and reference International Standards . 5
7 Labelling on package .6
8 Designation . 6
Bibliography . 7
iii
oSIST prEN ISO 13670:2024
ISO/DIS 13670:2023(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following
URL: www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 2, Fasteners and by Technical Committee
CEN/TC 185, Fasteners in collaboration.
iv
oSIST prEN ISO 13670:2024
DRAFT INTERNATIONAL STANDARD ISO/DIS 13670:2023(E)
Fasteners — Reverse-taper grooved pins — One quarter-
length progressive grooves on both sides
1 Scope
This document specifies the characteristics of reverse-taper grooved pins with one quarter-length
progressive grooves on both sides (with closed ends), in steel and stainless steel, and with nominal
diameters 2 mm to 25 mm.
These grooved pins are designed to fulfil the main following functions:
— relative rotation of the assembled parts, and
— locking of two (or more) parts,
with an easy installation due to its symmetrical shape and a medium level of pull-out resistance due to
the elastic fit behavior of the pin.
The general requirements (including functional principles for grooved pins and assembly) are specified
in ISO 13669.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
1)
ISO 13669 , Fasteners — Grooved pins — General requirements
ISO 1891-4, Fasteners — Vocabulary — Part 4: Control, inspection, delivery, acceptance and quality
ISO 3269, Fasteners — Acceptance inspection
ISO 3506-6, Fasteners — Mechanical properties of corrosion-resistant stainless steel fasteners — Part 6:
General rules for the selection of stainless steels and nickel alloys for fasteners
ISO 4042, Fasteners — Electroplated coating systems
ISO 6507-1, Metallic materials — Vickers hardness test — Part 1: Test method
ISO 8749, Pins and grooved pins — Shear test
ISO 9717, Metallic and other inorganic coatings — Phosphate conversion coating of metals
ISO 10683, Fasteners — Non-electrolytically applied zinc flake coating systems
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 13669 apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— ISO On
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.