SIST EN 1845:2008
(Main)Footwear manufacturing machines - Footwear moulding machines - Safety requirements
Footwear manufacturing machines - Footwear moulding machines - Safety requirements
1.1 This Standard applies to footwear moulding machines which are intended for use in the shoe industry for the production of footwear and footwear components.
These machines are:
3 direct-on sole moulding machines (see figures 1, 2, 3)
3 unit sole and footwear component moulding machines (see figure 4 - 10)
3 full shoe and boot moulding machines (see figure 11).
1.2 This Standard specifies safety requirements for construction, transport, installation, adjustment, setting, teaching or process change-over, operation, cleaning, maintenance, decommissioning, dismantling and, as far as safety is concerned, disposal for machines mentioned in l.1.
It deals with all significant hazards, hazardous situations and events relevant to footwear moulding machines , when they are used as intended and under the conditions foreseen by the manufacturer (see clause 4).
1.3 The following machines are excluded from the scope of this Standard unless used for direct-on sole moulding or reaction moulding:
3 moulding machines with static injection units and static mould
3 stations (clamping units),
3 moulding machines with static metering and mixing units and mobile stations with linear configuration (mould carriers).
1.4 The standard does not deal with hazards created by the mixing and metering unit
NOTE For metering and mixing units, see EN 1612-1.
The use of machines within the scope of this Standard in industries other than those specified in 1.1 may give rise to hazards not considered during its preparation.
NOTE For this application see also EN 201 and prEN 1612-2.
1.5 This standard also applies to the following additional equipment for material handling and operation which are an integral part of the machine:
spraying devices, injection units, casting units, nozzle cleaners, sprue pullers, mould front edge cleaners, activating devices, robots and equipment for preparatory and subsequent treatment (see fig. M.1).
1.6 This standard assumes the machines
3 are operate
Maschinen zur Herstellung von Schuhwerk - Schuhformmaschinen - Sicherheitsanforderungen
1.1 Diese Norm gilt für Schuhformmaschinen, die für die Herstellung von Schuhen und Schuhteilen in der Schuhindustrie verwendet werden.
Solche Maschinen sind:
Ansohlmaschinen (siehe Bilder 1, 2 und 3);
Sohlen- und Schuhteileformmaschinen (siehe Bilder 4 bis 10);
Schuh- und Stiefelformmaschinen (siehe Bild 11).
1.2 Diese Norm legt die Sicherheitsanforderungen für den Bau, den Transport, die Installation, das Einstellen, das Rüsten, die Programmierung oder die Verfahrensumstellung, den Betrieb, die Reinigung, die Wartung, die Beseitigung, die Zerlegung, und, soweit es die Sicherheit betrifft, auch für die Entsorgung der in I.1 erwähnten Maschinen fest.
Sie behandelt alle signifikanten Gefährdungen, gefahrbringenden Situationen und Ereignisse, die bei Schuhformmaschinen auftreten, wenn diese bestimmungsgemäß und unter vom Hersteller vorhersehbaren Bedingungen verwendet werden (siehe Abschnitt 4).
1.3 Folgende Maschinen sind vom Anwendungsbereich dieser Norm ausgenommen, außer sie werden zum Ansohlen oder zum Reaktionsgießen verwendet:
Formmaschinen mit stationären Spritzeinheiten und stationären Formenträgern;
Formenträger (Schließeinheiten);
Formmaschinen mit stationären Misch- und Dosiereinheiten und mit beweglichen Formenträgern (Werkzeugträger) in linearer Bauweise.
1.4 Diese Norm befasst sich nicht mit Gefährdungen, die durch die Misch- und Dosiereinheiten selbst hervorgerufen werden.
ANMERKUNG Misch- und Dosiereinheiten siehe EN 1612-1.
Der Einsatz von Maschinen nach dem Anwendungsbereich dieser Norm in anderen als in 1.1 genannten Industriezweigen kann zu Gefährdungen, die bei ihrer Ausarbeitung nicht berücksichtigt wurden, führen.
ANMERKUNG Bei solchen Anwendungen siehe EN 201 und prEN 1612-2.
Machines pour la fabrication des chaussures - Machines de moulage pour chaussures - Prescriptions de sécurité
1.1 La présente norme s'applique aux machines de moulage pour chaussures utilisées dans l'industrie de la chaussure pour la production de chaussures et d'articles chaussants.
Ces machines sont :
3 les machines de moulage direct des semelles (voir Figures 1, 2, 3) ;
3 les machines de moulage d'éléments de chaussures et de semelles (voir Figures 4 - 10) ;
3 les machines pour moulage complet de chaussures et bottes (voir Figure 11).
1.2 La présente norme spécifie les prescriptions de sécurité relatives a la construction, au transport, a l'installation, a la mise au point, au réglage, a l'apprentissage ou au changement de procédé de fabrication, au fonctionnement, au nettoyage, a la maintenance, a la mise hors service, au démontage et, pour autant que cela concerne la sécurité, a la mise au rebut des machines mentionnées en 1.1.
Elle traite de tous les phénomenes dangereux significatifs, situations et événements dangereux applicables aux machines de moulage pour chaussures, lorsqu'elles sont utilisées selon l'usage prévu et dans les conditions envisagées par le fabricant (voir l'article 4).
1.3 Les machines suivantes sont exclues du domaine d'application, sauf lorsqu'elles sont utilisées pour le moulage direct ou pour le moulage par réaction :
3 machines de moulage équipées d'unités d'injection statiques et de moules fixes ;
3 postes (unités de serrage) ;
3 machines de moulage équipées d'unités de dosage et de mélange statiques et de postes mobiles avec configuration linéaire (porte moules).
1.4 La présente norme ne traite pas des phénomenes dangereux générés par l'unité de mélange et de dosage.
NOTE Pour les unités de dosage et de mélange, voir l'EN 1612-1.
L'utilisation, dans d'autres secteurs industriels que ceux spécifiés en 1.1, des machines comprises dans le domaine d'application de la présente norme peut générer des risques qui n'ont pas été pris en considération lors de l'élaboration de la présente norme.
NOTE Pour cette application, voir également
Stroji za izdelavo obutve - Stroji za oblikovanje obutve - Varnostne zahteve
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Footwear manufacturing machines - Footwear moulding machines - Safety requirementsStroji za izdelavo obutve - Stroji za oblikovanje obutve - Varnostne zahteveMachines pour la fabrication des chaussures - Machines de moulage pour chaussures - Prescriptions de sécuritéMaschinen zur Herstellung von Schuhwerk - Schuhformmaschinen - SicherheitsanforderungenTa slovenski standard je istoveten z:EN 1845:2007SIST EN 1845:2008en,fr61.060ICS:SIST EN 1845:20001DGRPHãþDSLOVENSKI
STANDARDSIST EN 1845:200801-april-2008
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 1845December 2007ICS 61.060Supersedes EN 1845:1998
English VersionFootwear manufacturing machines - Footwear mouldingmachines - Safety requirementsMachines pour la fabrication des chaussures - Machines demoulage pour chaussures - Prescriptions de sécuritéMaschinen zur Herstellung von Schuhwerk -Schuhformmaschinen - SicherheitsanforderungenThis European Standard was approved by CEN on 3 November 2007.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2007 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 1845:2007: E
EN 1845:2007 (E) 2 Contents Page Foreword.4 Introduction.5 1 Scope.6 2 Normative references.7 3 Terms and definitions.9 4 List of significant hazards.10 5 Safety requirements and/or protective measures.14 5.1 General.14 5.2 Common requirements for all footwear moulding machines.15 5.2.1 Mechanical hazards.15 5.2.2 Electrical equipment.16 5.2.3 Thermal protection.16 5.2.4 Noise control.16 5.2.5 Fumes detrimental to health.17 5.2.6 Ergonomics.17 5.2.7 Pressurized fluid systems.18 5.2.8 Control systems.18 5.2.9 Additional safety devices.20 5.2.10 Material feeding.20 5.2.11 Auxiliary equipment.21 5.2.12 Integrated manufacturing systems.21 5.2.13 Aids for transportation.21 5.3 Requirements for specific types of footwear moulding machines.22 5.3.1 Direct-on sole moulding machines (see Figures 1, 2 and 3).22 5.3.2 Unit sole and footwear component moulding machines.28 5.3.3 Full shoe and boot moulding machines with rotary configuration (see Figure 11).39 6 Verification of safety requirements and/or measures.42 7 Information for use.49 7.1 General.49 7.2 Signal and warning devices.49 7.3 Instruction handbook.49 7.4 Declared noise emission values.51 7.5 Marking.51 Annex A (normative)
Requirements for guards.52 A.1 Fixed covers.52 A.2 Movable enclosing guards and movable covers.52 A.3 Fencing.52 Annex B (normative)
Requirements for interlocking systems.54 Annex C (normative)
Requirements for trip devices.58 C.1 Mechanical trip device with one position sensor.58 C.2 Electro-sensitive protective devices (ESPD) with normal level.59 C.3 Electro-sensitive protective devices (ESPD) with high level.59 C.4 Electro-sensitive protective devices (high level) with control function.60 C.5 Electro-sensitive protective device (ESPD) used as danger area protection.61 C.6 Active-opto-electric protective devices (laser scanner).61 Annex D (normative)
Requirements for two-hand control devices.62
EN 1845:2007 (E) 3 D.1 Two-hand control devices (normal level).62 D.2 Two-hand control devices (high level).62 Annex E (normative)
Requirements for hold-to-run control devices.64 E.1 Hold-to-run control devices (stop function, Figure E.1, illustration of the principle for pneumatic systems).64 E.2 Hold-to-run control devices (reverse function, Figure E.2, illustration of the principle for pneumatic systems).64 Annex F (normative)
Requirements for pressure sensitive mats (PSM) and floors (PSF).65 Annex G (normative)
Requirements for controls for mould closing.66 G.1 Power interlocking system.66 G.2 Control systems category 1 of EN ISO 13849-1.67 Annex H (normative)
Requirements for two-fault safety machine control systems.68 Annex I (normative)
Control measures for the suspension of safeguards relating to integrated manufacturing systems.70 Annex J (normative)
Requirements for control guards (interlocking guard with start function).72 Annex K (normative)
Temperatures of burn threshold.73 Annex L (normative)
Noise test code for footwear moulding machines.74 L.1 Scope.74 L.2 Definitions.74 L.2.1 Material.74 L.2.2 Processing temperature.74 L.2.3 Test cycle.74 L.2.4 Operator standing area (operating area).74 L.3 Description of machinery family.74 L.4 Measurement of A-weighted sound power level.74 L.5 Measurement of A-weighted emission sound pressure level.75 L.5.1 Position of microphone for determination of A-weighted emission sound pressure level at the workstation.75 L.6 Operating conditions.75 L.7 Measurement uncertainties.75 L.8 Documentation.75 Annex M (normative)
Important considerations relating to integrated manufacturing systems.77 M.1 Project organisation.77 M.2 Application of a safety strategy.77 M.3 Risk assessment.77 M.4 Requirements for documentation.77 M.5 Starting.78 M.6 Emergency stop.78 Annex ZA (informative)
Relationship between this European Standard and the essential requirements of EU Directive 98/37/EC.80 Annex ZB (informative)
Relationship between this European Standard and the Essential Requirements of EU Directive 2006/42/EC.81 Bibliography.82
EN 1845:2007 (E) 4 Foreword This document (EN 1845:2007) has been prepared by Technical Committee CEN/TC 201 “Leather and imitation leather goods and footwear manufacturing machinery - Safety”, the secretariat of which is held by UNI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by June 2008, and conflicting national standards shall be withdrawn at the latest by December 2008. This document supersedes EN 1845:1998. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of EU Directive(s). For relationship with EU Directive(s), see informative Annex ZA and ZB, which are an integral part of this document. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EN 1845:2007 (E) 5 Introduction This document is a type C standard as stated in EN ISO 12100. The machinery concerned and the extent to which hazards, hazardous situations and events are covered are indicated in the scope of this document. When provisions of this type C standard are different from those which are stated in type A or B standards, the provisions of this type C standard take precedence over the provisions of the other standards, for machines that have been designed and built according to the provisions of this type C standard.
EN 1845:2007 (E) 6 1 Scope 1.1 This European Standard applies to footwear moulding machines which are intended for use in the shoe industry for the production of footwear and footwear components. These machines are: direct-on sole moulding machines (see Figures 1, 2 and 3); unit sole and footwear component moulding machines (see Figures 4 to 10); full shoe and boot moulding machines (see Figure 11). This European Standard applies also to the mentioned machines when used for other products than footwear and footwear components, as far as these products require no other changes than a different mould. 1.2 This European Standard specifies safety requirements for construction, transport, installation, adjustment, setting, teaching or process change-over, operation, cleaning, maintenance, decommissioning, dismantling and, as far as safety is concerned, disposal for machines mentioned in l.1. It deals with all significant hazards, hazardous situations and events relevant to footwear moulding machines, when they are used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer (see Clause 4). 1.3 The following machines are excluded from the scope of this European Standard unless used for direct-on sole moulding or reaction moulding: moulding machines with static injection units and static mould stations (clamping units); moulding machines with static metering and mixing units and mobile stations with linear configuration (mould carriers). 1.4 The European Standard does not deal with hazards created by the mixing and metering unit. NOTE For metering and mixing units, see EN 1612-1. The use of machines within the scope of this European Standard in industries other than those specified in 1.1 may give rise to hazards not considered during its preparation. NOTE For this application see also EN 201 and prEN 1612-2. 1.5 This European Standard also applies to the following additional equipment for material handling and operation which are an integral part of the machine: spraying devices, injection units, casting units, nozzle cleaners, sprue pullers, mould front edge cleaners, activating devices, robots and equipment for preparatory and subsequent treatment (see Figure M.1). 1.6 This European Standard assumes the machines: are operated by adequately trained persons; are used with adequate workplace lighting (see EN 12464-1). 1.7 This document is not applicable to footwear moulding machines which are manufactured before the date of publication of this European Standard by CEN.
EN 1845:2007 (E) 7 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 294:1992, Safety of machinery — Safety distances to prevent danger zones being reached by the upper limbs EN 547-1:1996, Safety of machinery — Human body measurements — Part 1: Principles for determining the dimensions required for openings for whole body access into machinery EN 547-2:1996, Safety of machinery — Human body measurements — Part 2: Principles for determining the dimensions required for access openings EN 574:1996, Safety of machinery — Two-hand control devices — Functional aspects – Principles for design EN 614-1:2006, Safety of machinery — Ergonomic design principles — Part 1: Terminology and general principles EN 626-1:1994, Safety of machinery — Reduction of risks to health from hazardous substances emitted by machinery — Part 1: Principles and specifications for machinery manufacturers EN 626-2:1996, Safety of machinery — Reduction of risk to health from hazardous substances emitted by machinery — Part 2: Methodology leading to verification procedures EN 811:1996, Safety of machinery — Safety distances to prevent danger zones being reached by the lower limbs EN 894-2:1997, Safety of machinery — Ergonomics requirements for the design of displays and control actuators — Part 2: Displays EN 894-3:2000, Safety of machinery — Ergonomics requirements for the design of displays and control actuators — Part 3: Control actuators EN 953:1997, Safety of machinery — Guards – General requirements for the design and construction of fixed and movable guards EN 982:1996, Safety of machinery — Safety requirements for fluid power systems and their components — Hydraulics EN 983:1996, Safety of machinery — Safety requirements for fluid power systems and their components — Pneumatics EN 999:1998, Safety of machinery — The positioning of protective equipment in respect of approach speeds of parts of the human body
EN 1005-2:2003, Safety of machinery — Human physical performance — Part 2: Manual handling of machinery and component parts of machinery
EN 1005-3:2002, Safety of machinery — Human physical performance — Part 3: Recommended force limits for machinery operation EN 1037:1995, Safety of machinery — Prevention of unexpected start-up EN 1088:1995, Safety of machinery — Interlocking devices associated with guards — Principles for design and selection
EN 1845:2007 (E) 8 EN 1760-1:1997, Safety of machinery — Pressure sensitive protective devices — Part 1: General principles for the design and testing of pressure sensitive mats and pressure sensitive floors EN 1760-2:2001, Safety of machinery — Pressure sensitive protective devices — Part 2: General principles for the design and testing of pressure sensitive edges and pressure sensitive bars EN 1837:1999, Safety of machinery — Integral lighting of machines EN 12545:2000, Footwear, leather and imitation leather goods manufacturing machines — Noise test code — Common requirements EN 60204-1:2006, Safety of machinery — Electrical equipment of machines — Part 1: General requirements (IEC 60204-1:2005, modified) EN 60947-5-1:2004, Low-voltage switch gear and control gear — Part 5-1: Control circuit devices and switching elements — Electro-mechanical control circuit devices (IEC 60947-5-1:2003) EN 61310-1, Safety of machinery — Indication, marking and actuation — Part 1: Requirements for visual, auditory and tactile signals EN 61496-1:2004, Safety of machinery — Electro-sensitive protective equipment — Part 1: General requirements and tests (IEC 61496-1:2004, modified) CLC/TS 61496-2:2006, Safety of machinery — Electro-sensitive protective equipment — Part 2: Particular requirements for systems using active opto-electronic protective devices (APODs) CLC/TS 61496-3:2003, Safety of machinery — Electro-sensitive protective equipment — Part 3: Particular requirements for equipment using active opto-electronic responsive to diffuse reflection (AOPDDR) EN ISO 11688-1:1998, Acoustics — Recommended practice for the design of low-noise machinery and equipment — Part 1: Planning (ISO/TR 11688-1:1995) EN ISO 12100-1:2003, Safety of machinery — Basic concepts, general principles for design — Part 1: Basic terminology, methodology (ISO 12100-1:2003) EN ISO 12100-2:2003, Safety of machinery — Basic concepts, general principles for design — Part 2: Technical principles (ISO 12100-2:2003) EN ISO 13732-1:2006, Ergonomics of the thermal environment — Methods for the assessment of human responses to contact with surfaces — Part 1: Hot surfaces (ISO 13732-1:2006) EN ISO 13849-1:2006, Safety of machinery — Safety related parts of control systems — Part 1: General principles for design (ISO 13849-1:2006) EN ISO 13850:2006, Safety of machinery — Emergency stop — Principles for design (ISO 13850:2006) EN ISO 14121-1:2007, Safety of machinery — Risk assessment — Part 1: Principles (ISO 14121-1:2007) EN ISO 14122-1:2001, Safety of machinery — Permanent means of access to machinery — Part 1: Choice of a fixed means of access between two levels (ISO 14122-1:2001) EN ISO 14122-2:2001, Safety of machinery — Permanent means of access to machinery — Part 2: Working platforms and walkways (ISO 14122-2:2001)
EN 1845:2007 (E) 9 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN ISO 12100-1:2003 and the following apply. 3.1 footwear moulding machines either injection, pouring or direct-on vulcanising machines used in the footwear manufacturing industry only. The moulding stations of these machines may be either single or multiple, static or mobile and may have linear, rotary or conveyor configuration. The processed material may be either thermoplastic, thermosetting plastic, thermosetting elastomere, 2-component liquid polyurethane (PU) or rubber 3.2 direct-on sole moulding machines machines used to mould the sole directly onto a lasted upper. One side of the hollow mould is formed by the prepared base of the lasted upper 3.3 unit sole and footwear component moulding machines machines used to mould complete soles, inserts and shoe components independently of the uppers 3.4 full shoe and boot moulding machines machines used to mould a complete article of footwear by the injection of material into the cavity of a mould containing a mould last 3.5 static station machines mould stations are fixed in position. The moulds are filled with material either by their own individual nozzles, or by one or more nozzles which move from station to station 3.6 mobile station machines one or more nozzles are fixed in position. The mould stations are indexed to the nozzle(s) for filling 3.7 rotary configuration mould stations are arranged in a circle and rotate around a vertical axis 3.8 quadrant configuration fixed mould stations are arranged around part of the circumference of a circle, and the nozzle is moved in an arc between stations 3.9 linear configuration mould stations are arranged in a straight line 3.10 conveyor configuration moulds travel around a closed loop 3.11 injection process process of delivering rubber, thermo-plastic or reaction-foaming material through a nozzle into a closed mould 3.12 casting or pouring process delivery process consisting of 1 or more components which are cast or poured into an open mould
EN 1845:2007 (E) 10 3.13 vulcanizing process process where rubber material is placed in the mould (unit or direct-on). It is formed and cured using heat and pressure 3.14 fixed covers fixed guards installed directly at danger points to prevent alone, or together with other parts, unintentional access to the danger points from the covered side 3.15 fixed enclosing guards fixed guard which, when in position, prevents access to a danger zone by enclosure 3.16 fencing distance guard around danger zones of a machine or plant which prevents access from outside 3.17 integrated manufacturing system footwear moulding machine working together with other shoe machines and being operated by a supervisory control system 3.18 mould area area covered by the moving parts of the mould 3.19 power interlocking additional independent safety device not associated with a control system, designed to interrupt the power supply to the actuators of the hazardous movements 3.20 recurring access regular access into the mould area during the normal working cycle 4 List of significant hazards This clause contains all the significant hazards, hazardous situations and events, as far as they are dealt with in this standard, identified by risk assessment as significant for this type of machinery and which require action to eliminate or reduce the risk (see 4.1 to 4.9 of Table 1). NOTE Typical outlines of these machines together with significant danger areas are given in Figures 1 to 11, M.1. The figures are given for information only. The list of significant hazards is based upon EN ISO 14121-1. Also shown are the subclause references to the safety requirements and/or protective measures in the present standard. Before using the standard it is important to carry out a risk assessment of the footwear moulding machine to check that its significant hazards are identified in this clause.
EN 1845:2007 (E) 11
Table 1 — List of hazards Danger zone or source of hazard Type of hazard Figure/subfigure Relevant clauses of this standard 4.1
Mechanical hazards
5.2.1.1, 5.2.1.2, 5.2.1.3, 5.2.1.4, 5.2.1.5 4.1.1 Mould area: closing, clamping and opening movements of
- last - dummy last - side ring - toe cap device - rising sole mould - lid or cover - ejector crushing and shearing 1 (1a) 2 (2a, 2d), 3 4 (4c), 5 (5b), 6, 7 8, 9 10 (10c) 11
5.3.1.1.1 5.3.1.2.1 5.3.2.1.1 5.3.2.2.1 5.3.2.3.1 5.3.3.1 4.1.2 Area between fixed safeguarding and parts of machine and moulds, when table rotates or conveyor moves drawing-in, trapping, shearing or crushing 1 (1b) 4, 5, 6, 7 11 5.3.1.1.2 5.3.2.1.2 5.3.3.2 4.1.3 Operating area
5.3.2.1.3, 5.3.3.3 4.1.3.1 Power operated last rotation 1 (1c) 5.3.1.1.3.1 4.1.3.2 Power operated lid rotation crushing, shearing or impact 2 (2d), 3 5.3.1.2.4 4.1.3.3 Sole mould turning and shuttling device crushing and shearing 1 (1f) 2 (2d), 3 5.3.1.1.3.2 5.3.1.2.4 4.1.4 Area beneath rotary table shearing, crushing, drawing-in, trapping 1 (1e) 4 (4d), 5 (5b), 6, 7 11 (11b2) 5.3.1.1.4 5.3.2.1.4 5.3.3.4
EN 1845:2007 (E) 12
Table 1 — List of hazards (continued) Danger zone or source of hazard Type of hazard Figure/subfigure Relevant clauses of this standard 4.1.5 Operator's standing area - protruding parts - uneven, sloping, slippery platform - steps falling, slipping 1 (1g2), 2 (2d), 3, 4, 5 (5b), 6, 7, 8 (8b), 9, 10 (10e), 11 5.2.1.6 4.1.6 Movement of machine due to gravity while being transported crushing, shearing
5.2.
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.