SIST EN 15048-2:2007
(Main)Non-preloaded structural bolting assemblies - Part 2: Suitability test
Non-preloaded structural bolting assemblies - Part 2: Suitability test
This part of this European Standard specifies a tensile test for bolt/nut assemblies to guarantee their suitability for non-preloaded bolted connections in civil engineering structures. It applies to assemblies of bolts, nuts (and wash-ers if required) with dimensional and mechanical characteristics as specified in prEN 15048-1.
Garnituren für nicht planmäßig vorgespannte Schraubenverbindungen für den Metallbau - Teil 2: Eignungsprüfung
Dieser Teil dieser Europäischen Norm beschreibt einen Zugversuch für Garnituren aus Schrauben und
Muttern, um deren Eignung für nicht planmäßig vorgespannte Schraubenverbindungen in Stahlbauten
sicherzustellen. Er gilt für Schrauben, Muttern (und ggf. Scheiben) mit Maßen und mechanischen
Eigenschaften nach prEN 15048-1.
Boulonnerie de construction métallique non précontrainte - Partie 2 : Essai d'aptitude a l'emploi
La présente partie de la Norme européenne spécifie un essai de traction pour des boulons vis/écrou
permettant de garantir leur aptitude a l'emploi dans les assemblages boulonnés non précontraints des
ouvrages de génie civil. Elle s'applique aux ensembles de vis, écrous (et rondelles le cas échéant) dont les
caractéristiques dimensionnelles et mécaniques sont telles que spécifiées dans le prEN 15048-1.
Vijačne zveze brez prednapetja - 2. del: Preskus ustreznosti
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Garnituren für nicht planmäßig vorgespannte Schraubenverbindungen für den Metallbau - Teil 2: EignungsprüfungBoulonnerie de construction métallique non précontrainte - Partie 2 : Essai d'aptitude a l'emploiNon-preloaded structural bolting assemblies - Part 2: Suitability test21.060.10Sorniki, vijaki, stebelni vijakiBolts, screws, studsICS:Ta slovenski standard je istoveten z:EN 15048-2:2007SIST EN 15048-2:2007en,fr,de01-december-2007SIST EN 15048-2:2007SLOVENSKI
STANDARD
SIST EN 15048-2:2007
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 15048-2April 2007ICS 21.060.01 English VersionNon-preloaded structural bolting assemblies - Part 2: SuitabilitytestBoulonnerie de construction métallique non précontrainte -Partie 2 : Essai d'aptitude à l'emploiGarnituren für nicht planmäßig vorgespannteSchraubenverbindungen für den Metallbau - Teil 2:EignungsprüfungThis European Standard was approved by CEN on 6 August 2006.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2007 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 15048-2:2007: ESIST EN 15048-2:2007
EN 15048-2:2007 (E) 2
Contents Foreword.3 Introduction.4 1 Scope.5 2 Normative references.5 3 Terms and definitions.5 4 Symbols.5 5 Tensile test of bolt/nut assemblies.6 5.1 Principle.6 5.2 Test conditions.6 5.3 Required failure mode.7 5.4 Required tensile resistance.7 6 Test documentation.7 Annex A (informative)
Special testing conditions and procedures.9 Bibliography.10
SIST EN 15048-2:2007
EN 15048-2:2007 (E)
3 Foreword This document (EN 15048-2:2007) has been prepared by Technical Committee CEN/TC 185 “Fasteners”, the
secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by October 2007, and conflicting national standards shall be withdrawn at the latest by October 2009. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following coun-tries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Den-mark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. SIST EN 15048-2:2007
EN 15048-2:2007 (E) 4
Introduction This part of this European Standard is intended to test the tensile resistance of bolt/nut/washer assemblies to ensure that the assemblies are suitable for use in non-preloaded structural bolting. The assemblies may be used in shear connections or in tension connections if no preload is required. Structural fasteners which meet the requirements of this part of this European Standard have been designed to allow tensile loading of at least fub × As according to EN 1993-1-8 (Eurocode 3). NOTE As according to EN 1993-1-8 means As,nom according to the definition in Clause 4. SIST EN 15048-2:2007
EN 15048-2:2007 (E)
5 1 Scope This part of this European Standard specifie
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.