SIST EN 16592:2015
(Main)Packaging - Rigid plastic containers - PET finish 29/25 (12,6)
Packaging - Rigid plastic containers - PET finish 29/25 (12,6)
This document specifies the design and dimensions of the 29 mm screw finish with three (3) thread starts for
flat waters and non-carbonated beverages. This finish is designated PET finish 29/25 (12,6).
This finish can be used for aseptic filling and filling with introduction of nitrogen (internal overpressure inferior to 1 bar max). The dimension (12,6) is the height in millimetres from the top of finish to the bottom of the support ledge.
This finish is designed to accept a tamper evident plastic closure only. During first opening, the tamper evident band will separate from the closure shell and stay on a one way bottle neck or like bottles in the returnable market, the tamper evident band will tear but will remain connected to the closure shell.
Verpackung - 29/25 (12,6) Mündungstück für PET
Diese Europäische Norm legt die Konstruktion und die Maße für ein 29-mm-Schraubverschlussmundstück mit drei (3) Gewindegängen für stilles Wasser und kohlensäurefreie Getränke fest. Das Verschlussmundstück wird als PET-Verschlussmundstück 29/25 (12,6) bezeichnet.
Dieses Verschlussmundstück kann zur aseptischen Befüllung und zur Befüllung mit Stickstoffeinleitung (innerer Überdruck höchstens 1 bar) verwendet werden. Das Maß (12,6) ist die Höhe, in Millimeter, von der Oberkante des Verschlussmundstückes bis zur Unterseite des Halsstützrings.
Dieses Verschlussmundstück ist dafür ausgelegt, ausschließlich Kunststoffverschlüsse mit Originalitäts-sicherung aufzunehmen. Während des ersten Öffnens wird das Originalitätssicherungsband von der Verschlusskappe getrennt und bleibt bei einer Einwegflasche auf dem Flaschenhals zurück oder es reißt bei Mehrwegflaschen, bleibt aber mit der Verschlusskappe verbunden.
Emballage - Conteneurs plastiques rigides - Bague 29/25 (12,6) en PET
La présente Norme européenne définit la conception et les dimensions de la bague à vis de 29 mm à trois (3) filets pour le bouchage des eaux plates et boissons non carbonatées. Cette bague est désignée « bague PET 29/25 (12,6) ».
La bague peut être utilisée pour le conditionnement en milieu aseptique et/ou avec injection d'azote (surpression interne inférieure à 1 bar). La dimension (12,6) est la hauteur totale de la bague en millimètres.
Cette bague est prévue pour recevoir uniquement une capsule plastique avec témoin d'inviolabilité, ou bande de garantie. Lors de la première ouverture, le témoin d’inviolabilité se séparera de la capsule et restera sur la bouteille dans les cas d'utilisation d'une bouteille jetable ou, en cas d'utilisation de bouteilles retournables, le témoin d’inviolabilité se déchirera mais restera solidaire de la capsule.
Embalaža - Toge plastične posode - PET-grla 29/25 (12,6)
Ta dokument določa zasnovo in mere za navojno grlo s premerom 29 mm in trojnim (3) začetkom navoja za negazirano vodo in negazirane napitke. To grlo je namensko grlo PET 29/25 (12,6).
To grlo je mogoče uporabljati za aseptično polnjenje in polnjenje z dodajanjem dušika (notranji nadtlak nižji od največ 1 bara). Mera (12,6) je višina v milimetrih od vrha grla do dna podpornega okrajka. Grlu se lahko doda le plastičen čep, ki varuje pred nedovoljenim odpiranjem. Pri prvem odpiranju se obroček, ki varuje pred nedovoljenim odpiranjem, loči od lupine čepa in ostane na grlu steklenice ali pa se, kot pri povratnih steklenicah, pretrga, vendar ostane pritrjen na lupino čepa.
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Verpackung - 29/25 (12,6) Mündungstück für PETEmballage - Conteneurs plastiques rigides - Bague 29/25 (12,6) en PETPackaging - Rigid plastic containers - PET finish 29/25 (12,6)55.100Steklenice. Lonci. KozarciBottles. Pots. JarsICS:Ta slovenski standard je istoveten z:EN 16592:2014SIST EN 16592:2015en,fr,de01-januar-2015SIST EN 16592:2015SLOVENSKI
STANDARD
SIST EN 16592:2015
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 16592
October 2014 ICS 55.100 English Version
Packaging - Rigid plastic containers - PET finish 29/25 (12,6)
Emballage - Récipients en plastique rigide - Bague PET 29/25 (12,6)
Verpackung - Formstabile Kunststoffbehälter - PET-Verschlussmundstück 29/25 (12,6) This European Standard was approved by CEN on 6 September 2014.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2014 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 16592:2014 ESIST EN 16592:2015
EN 16592:2014 (E) 2 Contents Page Foreword .3 Introduction .4 1 Scope .5 2 Dimensions .5 3 Requirements .5 Bibliography .9
SIST EN 16592:2015
EN 16592:2014 (E) 3 Foreword This document (EN 16592:2014) has been prepared by Technical Committee CEN/TC 261 “Packaging”, the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by April 2015, and conflicting national standards shall be withdrawn at the latest by April 2015. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European S
...
SLOVENSKI STANDARD
oSIST prEN 16592:2013
01-julij-2013
(PEDODåD7RJHSODVWLþQHSRVRGH3(7JUOD
Packaging - Rigid plastic containers - PET finish 29/25 (12,6)
Verpackung - 29/25 (12,6) Mündungstück für PET
Emballage - Conteneurs plastiques rigides - Bague 29/25 (12,6) en PET
Ta slovenski standard je istoveten z: prEN 16592
ICS:
55.100 Steklenice. Lonci. Kozarci Bottles. Pots. Jars
oSIST prEN 16592:2013 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN 16592:2013
---------------------- Page: 2 ----------------------
oSIST prEN 16592:2013
EUROPEAN STANDARD
DRAFT
prEN 16592
NORME EUROPÉENNE
EUROPÄISCHE NORM
April 2013
ICS 55.100
English Version
Packaging - Rigid plastic containers - PET finish 29/25 (12,6)
Emballage - Conteneurs plastiques rigides - Bague PET Verpackung - Formstabile Kunststoffbehälter - PET-
29/25 (12,6) Verschlussmundstück 29/25 (12,6)
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee CEN/TC 261.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations which
stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other language
made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to
provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2013 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 16592:2013: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
oSIST prEN 16592:2013
prEN 16592:2013 (E)
Contents Page
Foreword .3
Introduction .4
1 Scope .5
2 Dimensions .5
3 Requirements .5
Bibliography .7
2
---------------------- Page: 4 ----------------------
oSIST prEN 16592:2013
prEN 16592:2013 (E)
Foreword
This document (prEN 16592:2013) has been prepared by Technical
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.