SIST EN 13126-1:2012
(Main)Building hardware - Hardware for windows and door height windows - Requirements and test methods - Part 1: Requirements common to all types of hardware
Building hardware - Hardware for windows and door height windows - Requirements and test methods - Part 1: Requirements common to all types of hardware
This European Standard specifies performance requirements for the strength and durability of hardware for the operation of movable sashes of windows and door height windows including requirements and test methods common to all hardware. This European Standard is applicable to the hardware suitable for windows and door height windows in Table 1, whatever the material used for the construction of the window.
Baubeschläge - Beschläge für Fenster und Fenstertüren - Anforderungen und Prüfverfahren - Teil 1: Gemeinsame Anforderungen an alle Arten von Beschlägen
Der vorliegende Teil dieser Europäischen Norm legt Leistungsanforderungen an die Festigkeit und
Dauerfunktionstüchtigkeit von Beschlägen für die Betätigung beweglicher Flügel von Fenstern und
Fenstertüren einschließlich der Anforderungen und Prüfverfahren fest, die für alle Beschläge gelten.
Diese Europäische Norm gilt für Beschläge, die für die in Tabelle 1 aufgeführten Fenster und Fenstertüren
geeignet sind, unabhängig von den für den Bau der Fenster verwendeten Werkstoffen.
Quincaillerie pour le bâtiment - Ferrures de fenêtres et portes-fenêtres - Exigences et méthodes d'essai - Partie 1: Exigences communes à tous les types de ferrures
La présente Norme européenne spécifie les exigences de performance relatives à la résistance et à
l'endurance des ferrures équipant les ouvrants de fenêtres et portes-fenêtres, en se limitant aux exigences et
méthodes d'essai communes à toutes les ferrures.
La présente Norme européenne s'applique aux ferrures utilisables sur les fenêtres et portes-fenêtres du
Tableau 1, quel que soit le matériau utilisé dans la construction de la fenêtre.
Stavbno okovje - Okovje za okna in zastekljena vrata - Zahteve in preskusne metode - 1. del: Zahteve, skupne vsem vrstam okovja
Ta evropski standard določa delovne zahteve za trdnost in trajnost okovja za delovanje premičnih okvirjev oken in zastekljenih vrat, vključno z zahtevami in preskusnimi metodami, ki so skupne vsem okovjem.
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Stavbno okovje - Okovje za okna in zastekljena vrata - Zahteve in preskusne metode - 1. del: Zahteve, skupne vsem vrstam okovjaBaubeschläge - Beschläge für Fenster und Fenstertüren - Anforderungen und Prüfverfahren - Teil 1: Gemeinsame Anforderungen an alle Arten von BeschlägenQuincaillerie pour le bâtiment - Ferrures de fenêtres et portes-fenêtres - Exigences et méthodes d'essai - Partie 1: Exigences communes à tous les types de ferruresBuilding hardware - Hardware for windows and door height windows - Requirements and test methods - Part 1: Requirements common to all types of hardware91.190Stavbna opremaBuilding accessoriesICS:Ta slovenski standard je istoveten z:EN 13126-1:2011SIST EN 13126-1:2012en,fr,de01-januar-2012SIST EN 13126-1:2012SLOVENSKI
STANDARDSIST EN 13126-1:20061DGRPHãþD
SIST EN 13126-1:2012
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 13126-1
November 2011 ICS 91.190 Supersedes EN 13126-1:2006English Version
Building hardware - Hardware for windows and door height windows - Requirements and test methods - Part 1: Requirements common to all types of hardware
Quincaillerie pour le bâtiment - Ferrures de fenêtres et portes-fenêtres - Exigences et méthodes d'essai - Partie 1: Exigences communes à tous les types de ferrures
Baubeschläge - Beschläge für Fenster und Fenstertüren - Anforderungen und Prüfverfahren - Teil 1: Gemeinsame Anforderungen an alle Arten von Beschlägen This European Standard was approved by CEN on 15 October 2011.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2011 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 13126-1:2011: ESIST EN 13126-1:2012
EN 13126-1:2011 (E) 2 Contents Page Foreword .4Introduction .51Scope .62Normative references .73Terms and definitions .84Classification .84.1General .84.2Category of use (1 – first digit) .94.3Durability (2 – second digit) .94.4Mass (3 – third digit) .94.5Fire resistance (4 – fourth digit) .94.6Safety in use (5 – fifth digit) .94.7Corrosion resistance (6 – sixth digit) .94.8Security (7 – seventh digit) .94.9Applicable part (8 – eighth digit) . 104.10Test sizes (9 – ninth digit) . 104.11Example of classification for hardware for Tilt&Slide windows (see EN 13126-17) . 105Requirements common to all types of hardware . 105.1Dangerous substances . 105.2Category of use (1 – first digit) . 115.3Durability (2 – second digit) . 115.4Mass (3 – third digit) . 115.5Fire resistance (4 – fourth digit) . 115.6Safety in use (5 – fifth digit) . 125.7Corrosion resistance (6 – sixth digit) . 125.8Security (7 – seventh digit) . 125.9Applicable part (8 – eighth digits) . 125.10Test sizes (9 – ninth digits) . 125.11Mechanical strength . 126Test equipment . 136.1General . 136.2Mounting of specimen . 136.3Test sizes . 136.4Profile and material of test windows and door height windows . 136.4.1General . 136.4.2Test specimen for hardware on timber windows and door height windows . 136.4.3Test specimen for hardware on PVC-U profile windows and door height windows . 146.4.4Test specimen for hardware used on aluminium or steel windows and door height windows . 146.4.5Clamping the specimen into the test-rig . 147Test methods . 157.1General . 157.2Lubrication of hardware . 157.3Sash-mass . 157.3.1Adjusting the sash-mass . 157.3.2Selecting the sash-mass . 157.4Resistance to corrosion . 15SIST EN 13126-1:2012
EN 13126-1:2011 (E) 3 8Test procedures . 168.1General . 168.2Durability test . 168.3Additional test requirements . 168.4Acceptance criteria . 169Marking . 16Annex A (informative)
List of parts and titles and their reference to the relevant window types . 17Annex B (informative)
Window types . 18Bibliography . 27 SIST EN 13126-1:2012
EN 13126-1:2011 (E) 4 Foreword This document (EN 13126-1:2011) has been prepared by Technical Committee CEN/TC 33 “Doors, windows, shutters, building hardware and curtain walling”, the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by May 2012, and conflicting national standards shall be withdrawn at the latest by May 2012. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 13126-1:2006. A full contribution to the preparation of this European Standard has been made by the European manufacturers’ organization "ARGE" and national standards bodies. This European Standard is one of a series of European Standards dedicated to building hardware products. It is divided into many parts: the first part being common to all the other parts of this Standards series, incorporating all types of hardware for windows and door height windows. Annex A (informative) lists the titles of all parts of this European Standard and refers to their different window opening-type applications. Where appropriate, additional normative and informative annexes are included in the respective part of this Standards series. The performance tests incorporated in this European Standard are considered to be reproducible and as such will provide a consistent and objective assessment of the performance of these products throughout CEN Member States. There are no significant changes to the previous version. The conversion of the CEN/TS into EN introduced only marginal changes in the wording. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. SIST EN 13126-1:2012
EN 13126-1:2011 (E) 5 Introduction EN 13126 is a multipart product standard which enables the testing of hardware components or sets. The components or sets are tested on a standard test frame independently of the windows to which they should be fitted. The standard test frame is intended to eliminate any test-result inconsistencies that may arise through the variability between different constructions of windows. NOTE 1 In some cases where the hardware components or sets are tested directly on a test rig or window; a standard test frame is not necessary. The applicable test specifications are listed in the individual parts of this Standards series. Throughout this European Standard all references to windows mean both windows and door height windows where appropriate. This European Standard applies only to hardware that connects a movable sash to its fixed frame or controls the opening and closing of the movable sash. It does not take fixing devices into account that are used to assemble or install a fixed window or permanently fix a complete window into a building structure. Where possible, test methods have been unified to accommodate a wide range of window opening-types and hardware. In particular, the following are unified for movable sashes: a) size of the sash; b) mass of the sash; c) frequency and total number of test cycles; d) range of operations during each test cycle. This European Standard excludes hardware for use on both doors and windows (single axis hinges and door bolts) because requirements for these products are specified in other standards. NOTE 2 The single complete standard consists of a combination of Part 1 together with one of the parts in this Standards series.
SIST EN 13126-1:2012
EN 13126-1:2011 (E) 6 1 Scope This European Standard specifies performance requirements for the strength and durability of hardware for the operation of movable sashes of windows and door height windows including requirements and test methods common to all hardware. This European Standard is applicable to the hardware suitable for windows and door height windows in Table 1, whatever the material used for the construction of the window. Table 1 — Window opening-types Window opening-type Description Description refers to EN 12519 Number of Figure in Annex B A Side-hung window inward opening
single (and double) side-hung casement, opening inwardsB.1 B Side-hung window outward opening
single (and double) side-hung casement, opening outwards B.1 C Bottom-hung window inward opening and outward opening bottom-hung casement, opening inwards or outwards B.2 D Top-hung window inward opening and outward opening
top-hung casement, opening inwards or outwards B.2 E Tilt&Turn, Tilt-First
tilt and turn windows B.3 F Horizontal pivot window
horizontal pivot casement, centre or off-centre B.4 G Vertical pivot window
vertical pivot casement, centre or off-centre B.4 H Projecting top-hung inward and outward opening window
sliding projecting, top-hung casement, opening inwards or outwards B.5 J Projecting bottom-hung inward and outward opening window this type is not separately described in EN 12519B.5 K Projecting reversible top-hung window this type is not separately described in EN 12519 B.6 L Projecting reversible side-hung window sliding projecting, side-hung casement, open outB.7 M Vertical sliding sash vertical sliding sash B.8 N Horizontal sliding sash horizontal sliding sash B.9 P Lifting sliding sash lifting sliding sashB.10 Q Folding window (centre pivot) this type is not separately described in EN 12519 B.11 R Folding outward opening window (corner pivot) sliding folding window B.12 S Folding inward opening window (corner pivot) sliding folding window
B.12 T Tilting sliding sash double tilting sliding sash B.13 U Top-hung inward opening window multi-light this type is not separately described in EN 12519B.14 V Bottom-hung inward opening window multi-light this type is not separately described in EN 12519B.14 W Horizontal balanced window this type is not separately described in EN 12519B.15
SIST EN 13126-1:2012
EN 13126-1:2011 (E) 7 This European Standard does not apply to the following: Fusible links, hardware for lifting side-hung windows, fixing devices that are used to assemble or install a fixed window, devices that are used for the permanent fixing of a complete window into a building structure, mechanisms for the pneumatic or hydraulic remote operation of windows; also single axis hinges (other than those, which provide a pivot-function for windows) and dead bolts suitable for both door and window sashes, as covered in EN 1935 and EN 12051 respectively. NOTE 1 If fire/smoke resistance is required, reference should be made to the respective standards mentioned in 5.5. NOTE 2 If burglar resistance is required, reference should be made to EN 1627, EN 1628, EN 1629 and EN 1630. 2 Normative references The following referenced documents are indispensable for the application of this European Standard. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 1634-1, Fire resistance and smoke control tests for door, shutter and openable window assemblies and elements of building hardware — Part 1: Fire resistance tests for doors, shutters and openable windows EN 1634-3, Fire resistance and smoke control tests for door and shutter assemblies, openable windows and elements of building hardware — Part 3: Smoke control test for door and shutter assemblies EN 1670, Building hardware — Corrosion resistance — Requirements and test methods EN 12519:2004, Windows and pedestrian doors —Terminology FprEN 13126-2, Building hardware — Requirements and test methods for windows and door height windows — Part 2: Window fastener handles FprEN 13126-3, Building hardware — Hardware for windows and door height windows — Requirements and test methods — Part 3: Handles, primarily for Tilt&Turn, Tilt-First and Turn-Only hardware EN 13126-4, Building hardware — Requirements and test methods for windows and door height windows — Part 4: Espagnolettes EN 13126-5, Building hardware — Hardware for windows and balcony doors — Requirements and test methods — Part 5: Devices that restrict the opening of windows EN 13126-6, Building hardware — Requirements and test methods for windows and doors height windows — Part 6: Variable geometry stay hinges (with or without a friction system) EN 13126-7, Building hardware — Requirements and test methods for windows and door height windows — Requirements and test methods — Part 7: Finger catches EN 13126-8, Building hardware — Requirements and test methods for windows and doors height windows — Part 8: — Tilt&Turn, Tilt-First and Turn-Only hardware CEN/TS 13126-9, Building hardware, fittings for windows and door height windows — Requirements and test methods — Part 9: Pivot hinges EN 13126-10, Building hardware — Requirements and test methods for windows and doors height windows— Part 10: Arm-balancing systems EN 13126-11, Building hardware — Requirements and test methods for windows and doors height windows — Part 11: Top hung projecting reversible hardware SIST EN 13126-1:2012
EN 13126-1:2011 (E) 8 EN 13126-12, Building hardware — Requirements and test methods for windows and doors height windows — Part 12: Side-hung projecting reversible hardware CEN/TS 13126-13, Building hardware, fittings for windows and door height windows — Requirements and test methods — Part 13: Sash balances CEN/TS 13126-14, Building hardware, fittings for windows and door height windows — Requirements and test methods — Part 14: Sash fasteners EN 13126-15, Building hardware — Requirements and test methods for windows and doors height windows — Part 15: Rollers for horizontal sliding and sliding folding windows and doors EN 13126-16, Building hardware — Requirements and test methods for windows and doors height windows — Part 16: Hardware for Li
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.