SIST EN 60603-7-3:2010

Connectors for electronic equipment - Part 7-3: Detail specification for 8-way, shielded, free and fixed connectors, for data transmission with frequencies up to 100 MHz (IEC 60603-7-3:2010)

This part of IEC 60603 covers 8-way, shielded, free and fixed connectors, references dimensional, mechanical, electrical and environmental characteristics and tests in IEC 60603-7 and IEC 60603-7-1, and specifies electrical transmission requirements for frequencies up to 100 MHz. These connectors are typically used as category 5 connectors in class D cabling systems specified in ISO/IEC 11801. These connectors are intermateable and interoperable with other IEC 60603-7 series connectors as defined in Clause 2 of IEC 60603-7. These connectors are backward compatible with other IEC 60603-7 series connectors.

Steckverbinder für elektronische Einrichtungen - Teil 7-3: Bauartspezifikation für geschirmte freie und feste Steckverbinder, 8polig, für Datenübertragungen bis 100 MHz (IEC 60603-7-3:2010)

Connecteurs pour équipements électroniques - Partie 7-3: Spécification particulière pour les fiches et les embases blindées à 8 voies pour la transmission de données à des fréquences jusqu'à 100 MHz (CEI 60603-7-3:2010)

La CEI 60603-7-3:2010 couvre les fiches et les embases blindées à 8 voies et renvoie à la CEI 60603-7 et à la CEI 60603-7-1 pour les caractéristiques et les essais dimensionnels, mécaniques, électriques et d'environnement, et elle spécifie les exigences de transmission électrique pour des fréquences jusqu'à 100 MHz. Ces connecteurs sont normalement utilisés comme connecteurs de catégorie 5 dans les systèmes de câblage de classe D spécifiés dans l'ISO/CEI  11801. Ces connecteurs sont accouplables et interopérables avec les autres connecteurs de la série CEI 60603-7 comme cela est défini à l'article 2 de la CEI 60603-7. Ces connecteurs offrent une compatibilité amont avec les autres connecteurs de la série CEI 60603-7.

Konektorji za elektronsko opremo - 7-3. del: Podrobna specifikacija za 8-redne, zaslonjene, proste in fiksne konektorje za prenos podatkov s frekvencami do 100 MHz (IEC 60603-7-3:2010)

Ta del IEC 60603 zajema 8-polne, zaslonjene, proste in fiksne konektorje in se sklicuje na dimenzijske, mehanske, električne in okoljske značilnosti in preskuse iz IEC 60603-7, ter določa zahteve za prevajanje električnega toka za frekvence do 100 MHz. Ti konektorji se običajno uporabljajo kot kategorija 5 konektorjev iz razreda D kabelskih sistemov, določenih v ISO/IEC 11801. Ti konektorji so medsebojno združljivi in interoperabilni z drugimi konektorji serije IEC 60603-7, kot je opredeljeno v Klavzuli 2 IEC 60603-7. Ti konektorji so povratno skladni z drugimi konektorji serije IEC 60603-7.

General Information

• Status: Published
• Publication Date: 22-Jul-2010
• ICS: 31.220.10 - Plug-and-socket devices. Connectors
• Technical Committee: I11 - Imaginarni 11
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 20-Jul-2010
• Due Date: 24-Sep-2010
• Completion Date: 23-Jul-2010
• Ref Project: EN 60603-7-3:2010 - Connectors for electronic equipment - Part 7-3: Detail specification for 8-way, shielded, free and fixed connectors, for data transmission with frequencies up to 100 MHz

Relations

• Replaces: SIST EN 60603-7-3:2010 - Connectors for electronic equipment - Part 7-3: Detail specification for 8-way, shielded, free and fixed connectors, for data transmission with frequencies up to 100 MHz (IEC 60603-7-3:2008)
• Effective Date: 01-Jul-2013

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 60603-7-3:2010
01-september-2010
1DGRPHãþD
SIST EN 60603-7-3:2010
Konektorji za elektronsko opremo - 7-3. del: Podrobna specifikacija za 8-redne,
zaslonjene, proste in fiksne konektorje za prenos podatkov s frekvencami do 100
MHz (IEC 60603-7-3:2010)
Connectors for electronic equipment - Part 7-3: Detail specification for 8-way, shielded,
free and fixed connectors, for data transmission with frequencies up to 100 MHz (IEC
60603-7-3:2010)
Steckverbinder für elektronische Einrichtungen - Teil 7-3: Bauartspezifikation für
geschirmte freie und feste Steckverbinder, 8polig, für Datenübertragungen bis 100 MHz
(IEC 60603-7-3:2010)
Connecteurs pour équipements électroniques - Partie 7-3: Spécification particulière pour
les fiches et les embases blindées à 8 voies pour la transmission de données à des
fréquences jusqu'à 100 MHz (CEI 60603-7-3:2010)
Ta slovenski standard je istoveten z: EN 60603-7-3:2010
ICS:
31.220.10 9WLþLLQYWLþQLFHNRQHNWRUML Plug-and-socket devices.
Connectors
SIST EN 60603-7-3:2010 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 60603-7-3:2010

---------------------- Page: 2 ----------------------

SIST EN 60603-7-3:2010

EUROPEAN STANDARD
EN 60603-7-3

NORME EUROPÉENNE
July 2010
EUROPÄISCHE NORM

ICS 31.220.10 Supersedes EN 60603-7-3:2009


English version


Connectors for electronic equipment -
Part 7-3: Detail specification for 8-way, shielded, free and fixed
connectors, for data transmission with frequencies up to 100 MHz
(IEC 60603-7-3:2010)


Connecteurs pour équipements Steckverbinder für elektronische
électroniques - Einrichtungen -
Partie 7-3: Spécification particulière Teil 7-3: Bauartspezifikation
pour les fiches et les embases blindées für geschirmte freie und feste
à 8 voies pour la transmission de données Steckverbinder, 8polig,
à des fréquences jusqu'à 100 MHz für Datenübertragungen bis 100 MHz
(CEI 60603-7-3:2010) (IEC 60603-7-3:2010)




This European Standard was approved by CENELEC on 2010-07-01. CENELEC members are bound to comply
with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard
the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the Central Secretariat or to any CENELEC member.

This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and notified
to the Central Secretariat has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus,
the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy,
Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia,
Spain, Sweden, Switzerland and the United Kingdom.

CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung

Management Centre: Avenue Marnix 17, B - 1000 Brussels


© 2010 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 60603-7-3:2010 E

---------------------- Page: 3 ----------------------

SIST EN 60603-7-3:2010
EN 60603-7-3:2010 - 2 -
Foreword
The text of document 48B/2136/FDIS, future edition 2 of IEC 60603-7-3, prepared by SC 48B,
Connectors, of IEC TC 48, Electromechanical components and mechanical structures for electronic
equipment, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as
EN 60603-7-3 on 2010-07-01.
This European Standard supersedes EN 60603-7-3:2009.
The main technical changes with regard to the previous edition are as follows:
– Removal of test methods that are now referenced to EN 60512-26-100.
– Addition of TCL and TCTL requirements.
– Removal of the electrical, mechanical, dimensional, environmental conditioning tests by reference to
EN 60603-7.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN and CENELEC shall not be held responsible for identifying any or all such patent
rights.
The following dates were fixed:
– latest date by which the EN has to be implemented
at national level by publication of an identical
national standard or by endorsement (dop) 2011-04-01
– latest date by which the national standards conflicting
with the EN have to be withdrawn (dow) 2013-07-01
Annex ZA has been added by CENELEC.
__________
Endorsement notice
The text of the International Standard IEC 60603-7-3:2010 was approved by CENELEC as a European
Standard without any modification.
In the official version, for Bibliography, the following note has to be added for the standard indicated:
IEC 60512-26-100:2008 NOTE  Harmonized as EN 60512-26-100:2008 (not modified).
__________

---------------------- Page: 4 ----------------------

SIST EN 60603-7-3:2010
- 3 - EN 60603-7-3:2010
Annex ZA
(normative)

Normative references to international publications
with their corresponding European publications

The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.

NOTE  When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD
applies.

Publication Year Title EN/HD Year

IEC 60512-1-100 - Connectors for electronic equipment - Tests EN 60512-1-100 -
and measurements -
Part 1-100: General - Applicable publications


IEC 60512-2-1 - Connectors for electronic equipment - Tests EN 60512-2-1 -
and measurements -
Part 2-1: Electrical continuity and contact
resistance tests - Test 2a: Contact resistance -
Millivolt level method


1)
IEC 60512-27-100 200X Connectors for electronic equipment - Tests - -
and measurements -
Part 27-100: Signal integrity tests up to 500
MHz on IEC 60603-7 series connectors - Tests
27a to 27g


IEC 60603-7 2008 Connectors for electronic equipment - EN 60603-7 2009
Part 7: Detail specification for 8-way,
unshielded, free and fixed connectors


IEC 60603-7-1 2009 Connectors for electronic equipment - EN 60603-7-1 2009
Part 7-1: Detail specification for 8-way,
shielded, free and fixed connectors


IEC 61156 Series Multicore and symmetrical pair/quad cables - -
for digital communications





1)
To be published.

---------------------- Page: 5 ----------------------

SIST EN 60603-7-3:2010

---------------------- Page: 6 ----------------------

SIST EN 60603-7-3:2010
IEC 60603-7-3
®
Edition 2.0 2010-04
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE


Connectors for electronic equipment –
Part 7-3: Detail specification for 8-way, shielded, free and fixed connectors, for
data transmission with frequencies up to 100 MHz

Connecteurs pour équipements électroniques –
Partie 7-3: Spécification particulière pour les fiches et les embases blindées à
8 voies pour la transmission de données à des fréquences jusqu'à 100 MHz

INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
PRICE CODE
INTERNATIONALE
M
CODE PRIX
ICS 31.220.10 ISBN 978-2-88910-230-3
® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale

---------------------- Page: 7 ----------------------

SIST EN 60603-7-3:2010
– 2 – 60603-7-3 © IEC:2010
CONTENTS
FOREWORD.3
INTRODUCTION.5
1 General .6
1.1 Scope.6
1.2 Normative references .6
2 Terms and definitions .7
3 Common features and isometric view .7
4 Cable terminations and internal connections – Fixed and free connectors .7
5 Gauges .7
6 Characteristics .7
6.1 General .7
6.2 Pin and pair grouping assignment. .7
6.3 Classification into climatic category.7
6.4 Electrical characteristics.7
6.5 Transmission characteristics .7
6.5.1 General .7
6.5.2 Insertion loss.8
6.5.3 Return loss .8
6.5.4 Propagation delay .8
6.5.5 Delay skew.8
6.5.6 NEXT .8
6.5.7 Power sum NEXT (for information only) .9
6.5.8 FEXT.9
6.5.9 Power sum FEXT (for information only) .9
6.5.10 Transverse conversion loss .9
6.5.11 Transverse conversion transfer loss .9
6.6 Mechanical.10
7 Tests and test schedule.10
7.1 General .10
7.2 Arrangement for contact resistance test: .10
7.3 Arrangement for vibration test .10
7.4 Test procedures and measuring methods .10
7.5 Preconditioning .10
7.6 Wiring and mounting of specimens .10
7.6.1 Wiring.10
7.6.2 Mounting .10
7.7 Test schedules .10
7.7.1 Basic (minimum) test schedule .10
7.7.2 Full test schedule .10
Bibliography.13

Table 1 – Test Group EP .11

---------------------- Page: 8 ----------------------

SIST EN 60603-7-3:2010
60603-7-3 © IEC:2010 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
______________

CONNECTORS FOR ELECTRONIC EQUIPMENT –

Part 7-3: Detail specification for 8-way, shielded, free and fixed
connectors, for data transmission with frequencies up to 100 MHz


FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between a
...