SIST EN 16063:2012

Packaging - Rigid plastic containers - Nomenclature of plastic finishes

This document specifies the plastic finish nomenclature used by the manufacturer of plastic containers and the tolerances for the dimensions.

Verpackung - Kunststoffbehältnisse - Bezeichnung von Kunststoffverschlussmundstücken

Für die Anwendung dieses Dokuments gelten die folgenden Begriffe.

Emballage - Récipients en plastique rigide - Nomenclature des bagues en plastique

Le présent document définit la nomenclature des dimensions relatives aux bagues en plastique.

Embalaža - Toge plastične posode - Nomenklatura za plastična grla

Ta dokument določa nomenklaturo mer za plastična grla.

General Information

• Status: Published
• Public Enquiry End Date: 19-Jun-2010
• Publication Date: 17-Jan-2012
• ICS: 55.100 - Bottles. Pots. Jars
• Technical Committee: EPO - Packaging - sales and grouped
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 17-Jan-2012
• Due Date: 23-Mar-2012
• Completion Date: 18-Jan-2012
• Ref Project: EN 16063:2011 - Packaging - Rigid plastic containers - Nomenclature of plastic finishes

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Verpackung - Kunststoffbehältnisse - Bezeichnung von KunststoffverschlussmundstückenEmballage - Récipients en plastique rigide - Nomenclature des bagues en plastiquePackaging - Rigid plastic containers - Nomenclature of plastic finishes55.100Steklenice. Lonci. KozarciBottles. Pots. JarsICS:Ta slovenski standard je istoveten z:EN 16063:2011SIST EN 16063:2012en,fr,de01-marec-2012SIST EN 16063:2012SLOVENSKI
STANDARD



SIST EN 16063:2012



EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 16063
November 2011 ICS 55.100 English Version
Packaging - Rigid plastic containers - Nomenclature of plastic finishes
Emballage - Récipients en plastique rigide - Nomenclature des bagues en plastique
Verpackung - Kunststoffbehältnisse - Bezeichnung von Kunststoffverschlussmundstücken This European Standard was approved by CEN on 29 October 2011.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2011 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 16063:2011: ESIST EN 16063:2012



EN 16063:2011 (E) 2 Contents Page Foreword .3Introduction .41 Scope .52 Terms and definitions .53 Requirements .5Bibliography .7 SIST EN 16063:2012



EN 16063:2011 (E) 3 Foreword This document (EN 16063:2011) has been prepared by Technical Committee CEN/TC 261 “Packaging”, the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by May
...