SIST EN ISO 14579:2002
(Main)Hexalobular socket head cap screws (ISO 14579:2001)
Hexalobular socket head cap screws (ISO 14579:2001)
Zylinderschrauben mit Innensechsrund (ISO 14579:2001)
Diese Internationale Norm legt die Eigenschaften von Zylinderschrauben mit Innensechsrund, mit Gewinde von M2 bis M20, mit Produktklasse A fest.
Werden in besonderen Fällen andere als in dieser Internationalen Norm aufgeführte Festlegungen benötigt, sollten diese aus bestehenden Internationalen Normen wie zum Beispiel ISO 261, ISO 888, ISO 898-1, ISO 965-2,
ISO 965-3, ISO 3506-1 und ISO 4759-1 ausgewählt werden.
Vis a métaux a tete cylindrique a six lobes internes (ISO 14579:2001)
La présente Norme internationale spécifie les caractéristiques des vis à métaux à tête cylindrique à six lobes internes, de filetage M2 à M30 inclus et de grade A. Si, dans des cas particuliers, des spécifications autres que celles figurant dans la présente Norme internationale sont requises, il est recommandé de les choisir dans les Normes internationales existantes, par exemple ISO 261, ISO 888, ISO 898-1, ISO 965-2, ISO 3506-1 et ISO 4759-1.
Notranji šestrogeljnik v valjasti glavi vijaka (ISO 14579:2001)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 14579:2002
01-julij-2002
Notranji šestrogeljnik v valjasti glavi vijaka (ISO 14579:2001)
Hexalobular socket head cap screws (ISO 14579:2001)
Zylinderschrauben mit Innensechsrund (ISO 14579:2001)
Vis a métaux a tete cylindrique a six lobes internes (ISO 14579:2001)
Ta slovenski standard je istoveten z: EN ISO 14579:2001
ICS:
21.060.10 Sorniki, vijaki, stebelni vijaki Bolts, screws, studs
SIST EN ISO 14579:2002 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 14579:2002
---------------------- Page: 2 ----------------------
SIST EN ISO 14579:2002
EUROPEAN STANDARD
EN ISO 14579
NORME EUROPÉENNE
EUROPÄISCHE NORM
September 2001
ICS 21.060.10
English version
Hexalobular socket head cap screws (ISO 14579:2001)
Vis à métaux à tête cylindrique à six lobes internes (ISO Zylinderschrauben mit Innensechsrund (ISO 14579:2001)
14579:2001)
This European Standard was approved by CEN on 1 September 2001.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,
Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2001 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 14579:2001 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 14579:2002
EN ISO 14579:2001 (E)
CORRECTED 2002-02-06
Foreword
This document (ISO 14579:2001) has been prepared by Technical Committee ISO/TC 2
"Fasteners" in collaboration with Technical Committee CEN/TC 185 "Threaded and non-
threaded mechanical fasteners and accessories", the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of
an identical text or by endorsement, at the latest by March 2002, and conflicting national
standards shall be withdrawn at the latest by March 2002.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of
the following countries are bound to implement this European Standard: Austria, Belgium, Czech
Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg,
Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of the International Standard ISO 14579:2001 has been approved by CEN as a
European Standard without any modifications.
NOTE Normative references to International Standards are listed in annex ZA (normative).
2
---------------------- Page: 4 ----------------------
SIST EN ISO 14579:2002
EN ISO 14579:2001 (E)
Annex ZA
(normative)
Normative references to international publications
with their relevant European publications
This European Standard incorporates by dated or undated reference, provisions from other
publications. These normative references are cited at the appropriate places in the text and the
publications are listed hereafter. For dated references, subsequent amendments to or revisions of
any of these publications apply to this European Standard only when incorporated in it by
amendment or revision. For undated references the latest edition of the publication referred to
applies (including amendments).
NOTE Where an International Publication has been modified by common modifications, indicated
by (mod.), the relevant EN/HD applies.
Publication Year Title EN Year
ISO 225 1983 Fasteners — Bolts, screws, studs and EN 20225 1991
nuts — Symbols and designations of
dimensions
ISO 898-1 1999 Mechanical properties of fasteners EN ISO 898-1 1999
made of carbon steel and alloy steel
— Part 1: Bolts, screws and studs
ISO 3269 2000 Fasteners — Acceptance inspection EN ISO 3269 2000
ISO 3506-1 1997 Mechanical properties of corrosion- EN ISO 3506-1 1997
resistant stainless-steel fasteners —
Part 1: Bolts, screws and studs
ISO 4042 1999 Fasteners — Electroplated coatings EN ISO 4042 1999
ISO 4753 1999 Fasteners — Ends of parts with EN ISO 4753 1999
external ISO metric thread
ISO 4759-1 2000 Tolerances for fasteners — Part 1: EN ISO 4759-1 2000
Bolts, screws, studs and nuts —
Product grades A, B and C
ISO 6157-1 1988 Fasteners — Surface discontinuities EN 26157-1 1991
— Part 1: Bolts, screws and studs for
general requirements
ISO 6157-3 1988 Fasteners — Surface discontinuities EN 26157-3 1991
— Part 3: Bolts, screws and studs for
special requirements
ISO 8839 1986 Mechanical properties of fasteners — EN 28839 1991
Bolts, screws, studs and nuts made of
non-ferrous metals
ISO 10664 1999 Hexalobular internal driving feature EN ISO 10664 1999
for bolts and screws
ISO 10683 2000 Fasteners — Non-electrolytically EN ISO 10683 2000
applied zinc flake coatings
3
---------------------- Page: 5 ----------------------
SIST EN ISO 14579:2002
---------------------- Page: 6 ----------------------
SIST EN ISO 14579:2002
INTERNATIONAL ISO
STANDARD 14579
First edition
2001-09-01
Hexalobular socket head cap screws
Vis à métaux à tête cylindrique à six lobes internes
Reference number
ISO 14579:2001(E)
©
ISO 2001
---------------------- Page: 7 ----------------------
SIST EN ISO 14579:2002
ISO 14579:2001(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not
be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this
file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this
area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters
were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event
that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2001
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic
or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body
in the country of the requester.
ISO copyright office
Case postale 56 � CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.ch
Web www.iso.ch
Printed in Switzerland
ii © ISO 2001 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 14579:2002
ISO 14579:2001(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO
member bodies). The work of preparing International Standards is normally carried out through ISO technical
committees. Each member body interested in a subject for which a technical committee has been established has
the right to be represented on that committee. International organizations, governmental and non-governmental, in
liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical
Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3.
Draft International Standards adopted by the technical committees are circulated to the member bodies for voting.
Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this International Standard may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights.
International Standard ISO 14579 was prepared by Technical Committee ISO/TC 2, Fasteners.
Annex A of this International Stanfdard is for information only.
© ISO 2001 – All rights reserved iii
---------------------- Page: 9 ----------------------
SIST EN ISO 14579:2002
---------------------- Page: 10 ----------------------
SIST EN ISO 14579:2002
INTERNATIONAL STANDARD ISO 14579:2001(E)
Hexalobular socket head cap screws
1 Scope
This International Standard specifies the characteristics of hexalobular socket head cap screws with thread sizes
from M2 up to and including M20, of product grade A.
If, in special cases, specifications other than those listed in this International Standard are required, they should be
selected from existing International Standards, e.g. ISO 261, ISO 888, ISO 898-1, ISO 965-2, ISO 965-3,
ISO 3506-1, ISO 4759-1.
2 Normative references
The following normative documents contain provisions which, through reference in this text, constitute provisions of
this International Standard. For dated references, subsequent amendments to, or revisions of, any of these
publications do not apply. However, parties to
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.