SIST EN ISO 15980:2003

Open end blind rivets with break pull mandrel and countersunk head - St/St (ISO 15980:2002)

ISO 15980 specifies dimensional and mechanical characteristics and application data for open end blind rivets with break pull mandrel and protruding head, with a steel body and a steel mandrel and with nominal diameters from 2,4 mm up to and including 6,4 mm.

Offene Blindniete mit Sollbruchdorn und Senkkopf - St/St (ISO 15980:2002)

Diese Internationale Norm legt Maße und mechanische Eigenschaften sowie Anwendungsdaten für offene Blindniete mit Sollbruchdorn und Senkkopf, mit einer Niethülse aus Stahl (St) und einem Nietdorn aus Stahl (St) und mit Nenndurchmessern, d, von 2,4 mm bis 6,4 mm fest.Diese Internationale Norm legt Maße und mechanische Eigenschaften sowie Anwendungsdaten für offene Blindniete mit Sollbruchdorn und Senkkopf, mit einer Niethülse aus Stahl (St) und einem Nietdorn aus Stahl (St) und mit Nenndurchmessern, d, von 2,4 mm bis 6,4 mm fest.

Rivets aveugles a rupture de tige a corps ouvert, a tete fraisée - St/St (ISO 15980:2002)

L'ISO 15980:2002 spécifie les caractéristiques dimensionnelles et mécaniques ainsi que les données d'application pour les rivets aveugles à rupture de tige à corps ouvert, à tête fraisée, avec un corps en acier (St) et une tige en acier (St), de diamètre nominal compris entre 2,4 mm et 6,4 mm inclus.

Slepe votle kovice z zarezanim zakovnim trnom in ugrezno glavo - St/St (ISO 15980:2002)

General Information

• Status: Published
• Publication Date: 30-Jun-2003
• ICS: 21.060.40 - Rivets
• Technical Committee: ISEL - Mechanical elements
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 01-Jul-2003
• Due Date: 01-Jul-2003
• Completion Date: 01-Jul-2003
• Ref Project: EN ISO 15980:2002 - Open end blind rivets with break pull mandrel and countersunk head - St/St (ISO 15980:2002)

Overview

EN ISO 15980:2002 specifies requirements for open end blind rivets with a break‑pull mandrel and countersunk (protruding) head, with both rivet body and mandrel made of steel (St/St). The standard covers dimensional, mechanical and application data for nominal diameters from 2.4 mm up to and including 6.4 mm, and defines surface finish, testing and acceptance criteria for these blind rivets.

Key topics and technical requirements

• Scope and sizes: Nominal diameters d = 2.4 mm to 6.4 mm; recommended grip ranges and nominal lengths are specified.
• Dimensions: Detailed rivet geometry (head diameter, head height, shank diameter, blind length) and clearance hole guidance; clearance hole diameter h1 = nominal + 0.1 mm (min) to + 0.2 mm (max).
• Materials and finish: Rivet body and mandrel made of steel (St/St). Rivet body must be zinc plated ≥ 5 µm with chromate conversion coating c2C (designated Fe/Zn5c2C); mandrel finish at manufacturer’s discretion.
• Mechanical properties: Minimum shear and tensile loads and maximum mandrel break loads are specified per nominal diameter. For the range covered, shear spans about 650 N to 4 900 N, tensile 700 N to 5 700 N, and mandrel break load 2 000 N to 13 000 N (values given per size in the standard).
• Performance tests: Mechanical testing, mandrel push‑out resistance (>10 N), and mandrel head retention test loads are required (tests referenced to ISO 14589).
• Workmanship and acceptance: Rivets must be free of burrs and cracking (inspection at 5× magnification); acceptance inspection follows ISO 3269.

Applications

EN ISO 15980:2002 applies to design, manufacture, procurement and quality assurance of steel open‑end blind rivets used where a countersunk head is required on the accessible side. Typical uses include:

• Structural and sheet‑metal assembly in construction, transport, HVAC and metal fabrication
• Equipment and appliance assembly where blind fastening from one side is needed
• Retrofitting and field repairs where access to only one side of the joint is available

Who uses this standard

• Fastener manufacturers and tooling suppliers
• Design and mechanical engineers specifying fasteners
• Procurement and quality inspectors verifying conformity
• Test laboratories performing mechanical tests and acceptance inspections

Related standards

Normative references and related documents include:

• ISO 14588 (blind rivet terminology), ISO 14589 (mechanical testing)
• ISO 3269 (acceptance inspection), ISO 4042 (electroplated coatings)
• ISO 4520 (chromate conversion coatings)

Example designation format from the standard: Blind rivet ISO 15980 - 4 ×××× 12 - St/St

Keywords: EN ISO 15980:2002, open end blind rivets, break pull mandrel, countersunk head, St/St, steel rivets, blind rivet dimensions, rivet mechanical properties.

Standards Content (Sample)

SLOVENSKI STANDARD
01-julij-2003
Slepe votle kovice z zarezanim zakovnim trnom in ugrezno glavo - St/St (ISO
15980:2002)
Open end blind rivets with break pull mandrel and countersunk head - St/St (ISO
15980:2002)
Offene Blindniete mit Sollbruchdorn und Senkkopf - St/St (ISO 15980:2002)
Rivets aveugles a rupture de tige a corps ouvert, a tete fraisée - St/St (ISO 15980:2002)
Ta slovenski standard je istoveten z: EN ISO 15980:2002
ICS:
21.060.40 Kovice Rivets
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN ISO 15980
NORME EUROPÉENNE
EUROPÄISCHE NORM
November 2002
ICS 21.060.40
English version
Open end blind rivets with break pull mandrel and countersunk
head - St/St (ISO 15980:2002)
Rivets aveugles à rupture de tige à corps ouvert, à tête Offene Blindniete mit Sollbruchdorn und Senkkopf - St/St
fraisée - St/St (ISO 15980:2002) (ISO 15980:2002)
This European Standard was approved by CEN on 14 October 2002.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,
Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2002 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 15980:2002 E
worldwide for CEN national Members.

CORRECTED  2002-12-18
Foreword
This document (EN ISO 15980:2002) has been prepared by Technical Committee ISO/TC 2
"Fasteners" in collaboration with Technical Committee CEN/TC 185 "Threaded and non-
threaded mechanical fasteners and accessories", the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of
an identical text or by endorsement, at the latest by May 2003, and conflicting national standards
shall be withdrawn at the latest by May 2003.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of
the following countries are bound to implement this European Standard: Austria, Belgium, Czech
Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg,
Malta, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of ISO 15980:2002 has been approved by CEN as EN ISO 15980:2002 without any
modifications.
NOTE Normative references to International Standards are listed in Annex ZA (normative).
Annex ZA
(normative)
Normative references to international publications
with their relevant European publications
This European Standard incorporates by dated or undated reference, provisions from other
publications. These normative references are cited at the appropriate places in the text and the
publications are listed hereafter. For dated references, subsequent amendments to or revisions of
any of these publications apply to this European Standard only when incorporated in it by
amendment or revision. For undated references the latest edition of the publication referred to
applies (including amendments).
NOTE Where an International Publication has been modified by common modifications, indicated
by (mod.), the relevant EN/HD applies.
Publication Year Title EN Year
ISO 3269 2000 Fasteners - Acceptance EN ISO 3269 2000
inspection
ISO 4042 1999 Fasteners - Electroplated EN ISO 4042 1999
coatings
ISO 14588 2000 Blind rivets - Terminology and EN ISO 14588 2000
definitions
ISO 14589 2000 Blind rivets - Mechanical testing EN ISO 14589 2000
INTERNATIONAL ISO
STANDARD 15980
First edition
2002-11-01
Open end blind rivets with break pull
mandrel and countersunk head — St/St
Rivets aveugles à rupture de tige à corps ouvert, à tête fraisée — St/St

Reference number
ISO 15980:2002(E)
©
ISO 2002
ISO 15980:2002(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not
be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this
file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this
area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters
were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event
that a problem relating to it is found, please inform the Central Secretariat at the address given below.

©  ISO 2002
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic
or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body
in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail [e-mail]
Web www.iso.ch
Printed in Switzerland
ii © ISO 2002 – All rights reserved

ISO 15980:2002(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO
member bodies). The work of preparing International Standards is normally carried out through ISO technical
committees. Each member body interested in a subject for which a technical committee has been established has
the right to be represented on that committee. International organizations, governmental and non-governmental, in
liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical
Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3.
The main task of technical committees is to prepare International Standards. Draft International Standards adopted
by the technical committees are circulated to the member bodies for voting. Publication as an International
Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this International Standard may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 15980 was prepared by Technical Committee ISO/TC 2, Fasteners.
Annex A of this International Sta
...