SIST EN 302 372 V2.1.1:2017
(Main)Short Range Devices (SRD) - Tank Level Probing Radar (TLPR) equipment operating in the frequency ranges 4,5 GHz to 7 GHz, 8,5 GHz to 10,6 GHz, 24,05 GHz to 27 GHz, 57 GHz to 64 GHz, 75 GHz to 85 GHz - Harmonised Standard covering the essential requirements of article 3.2 of the Directive 2014/53/EU
Short Range Devices (SRD) - Tank Level Probing Radar (TLPR) equipment operating in the frequency ranges 4,5 GHz to 7 GHz, 8,5 GHz to 10,6 GHz, 24,05 GHz to 27 GHz, 57 GHz to 64 GHz, 75 GHz to 85 GHz - Harmonised Standard covering the essential requirements of article 3.2 of the Directive 2014/53/EU
The present document contains requirements to demonstrate that TLPR equipment both effectively uses and supports the efficient use of radio spectrum in order to avoid harmful interference.
TLPRs are used for tank level measurement applications in many industries concerned with process control to measure the amount of various substances (mostly liquids or granulates). TLPRs are used for a wide range of applications such as process control, custody transfer measurement (government legal measurements), water and other liquid monitoring,
spilling prevention and other industrial applications. The main purposes of using TLPRs are:
• to increase reliability by preventing accidents;
• to increase industrial efficiency, quality and process control;
• to improve environmental conditions in production processes.
The present document applies to TLPRs radiating RF signals towards the surface of a substance contained in a closed tank. Any radiation outside of the tank is caused by leakage and is considered as unintentional emission. The present document does not necessarily include all the characteristics, which may be required by a user, nor does it necessarily represent the optimum performance achievable, it applies only to TLPRs fitted with dedicated antennas.
TLPRs always consist of a combined transmitter and receiver and are used with an integral or dedicated antenna. The TLPR equipment is for professional applications where installation and maintenance are performed by professionally trained individuals only.
The scope is limited to TLPRs operating as Short Range Devices (SRD), in which the devices are installed in closed metallic tanks or reinforced concrete tanks, or similar enclosure structures made of comparable attenuating material, holding a substance, liquid or powder.
The TLPR applications in the present document are not intended for communication purposes. Their intended usage excludes any intended radiation into free space.
Naprave kratkega dosega (SRD) - Oprema radarja za sondiranje nivoja v rezervoarjih (TLPR), ki deluje v frekvenčnih območjih od 4,5 GHz do 7 GHz, od 8,5 GHz do 10,6 GHz, od 24,05 GHz do 27 GHz, od 57 GHz do 64 GHz in od 75 GHz do 85 GHz - Harmonizirani standard, ki zajema bistvene zahteve člena 3.2 direktive 2014/53/EU
Ta dokument vključuje zahteve, s katerimi se dokazuje, da je oprema radarja za sondiranje nivoja v rezervoarjih (TLPR) izdelana tako, da učinkovito uporablja in podpira učinkovito rabo radijskega spektra z namenom preprečevanja škodljivega motenja.
Radarji za sondiranje nivoja v rezervoarjih se uporabljajo za merjenje nivoja v rezervoarjih v številnih industrijskih dejavnostih, povezanih z nadzorom procesov, pri čemer se izmeri količina različnih snovi (večinoma tekočin ali granulatov). Radarji za sondiranje nivoja v rezervoarjih se uporabljajo za različne namene, npr. za nadzor procesov, meritve pri prenosu skrbništva (zakonsko določene meritve), nadzor vode in drugih tekočin,
preprečevanje razlitja ter za druge vrste industrijske uporabe. Glavni nameni uporabe radarjev za sondiranje nivoja v rezervoarjih so:
• povečanje zanesljivosti s preprečevanjem nesreč;
• povečanje učinkovitosti, kakovosti in nadzora procesov v industriji;
• izboljšanje okoljskih pogojev v proizvodnih postopkih.
Ta dokument se uporablja za radarje za sondiranje nivoja v rezervoarjih, ki sevajo radiofrekvenčne signale proti površini snovi v zaprtem rezervoarju. Kakršno koli sevanje zunaj rezervoarja nastane zaradi puščanja in se upošteva kot nenamerno sevanje. Ta dokument ne vključuje nujno vseh lastnosti, ki bi jih morda potreboval uporabnik, in ne predstavlja nujno najboljšega mogočega delovanja; uporablja se samo za radarje za sondiranje nivoja v rezervoarjih, ki so nameščeni z namenskimi antenami.
Radarji za sondiranje nivoja v rezervoarjih so vedno opremljeni s kombiniranim oddajnikom in sprejemnikom ter se uporabljajo z vgrajeno ali namensko anteno. Oprema radarjev za sondiranje nivoja v rezervoarjih je namenjena za profesionalno uporabo, pri kateri namestitev in vzdrževanje izvajajo samo strokovno usposobljene osebe.
Področje uporabe je omejeno na radarje za sondiranje nivoja v rezervoarjih, ki delujejo kot naprave kratkega dosega (SRD), pri čemer so naprave nameščene v zaprtih kovinskih rezervoarjih ali rezervoarjih iz armiranega betona ali podobnih ohišjih, izdelanih iz primerljivo slabilnega materiala, v katerih je shranjena snov, tekočina ali prah.
Uporaba radarjev za sondiranje nivoja v rezervoarjih iz tega dokumenta ni namenjena za komunikacijo. Njihov predvideni namen uporabe izključuje kakršno koli namerno sevanje v okolje.
General Information
Buy Standard
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 302 372 V2.1.1:2017
01-februar-2017
1DSUDYHNUDWNHJDGRVHJD 65' 2SUHPDUDGDUMD]DVRQGLUDQMHQLYRMDY
UH]HUYRDUMLK 7/35 NLGHOXMHYIUHNYHQþQLKREPRþMLKRG*+]GR*+]RG
*+]GR*+]RG*+]GR*+]RG*+]GR*+]LQRG*+]GR
*+]+DUPRQL]LUDQLVWDQGDUGNL]DMHPDELVWYHQH]DKWHYHþOHQDGLUHNWLYH
(8
Short Range Devices (SRD) - Tank Level Probing Radar (TLPR) equipment operating in
the frequency ranges 4,5 GHz to 7 GHz, 8,5 GHz to 10,6 GHz, 24,05 GHz to 27 GHz, 57
GHz to 64 GHz, 75 GHz to 85 GHz - Harmonised Standard covering the essential
requirements of article 3.2 of the Directive 2014/53/EU
Ta slovenski standard je istoveten z: ETSI EN 302 372 V2.1.1 (2016-12)
ICS:
33.060.99 Druga oprema za radijske Other equipment for
komunikacije radiocommunications
SIST EN 302 372 V2.1.1:2017 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 302 372 V2.1.1:2017
---------------------- Page: 2 ----------------------
SIST EN 302 372 V2.1.1:2017
ETSI EN 302 372 V2.1.1 (2016-12)
HARMONISED EUROPEAN STANDARD
Short Range Devices (SRD);
Tank Level Probing Radar (TLPR) equipment operating in the
frequency ranges 4,5 GHz to 7 GHz, 8,5 GHz to 10,6 GHz,
24,05 GHz to 27 GHz, 57 GHz to 64 GHz, 75 GHz to 85 GHz;
Harmonised Standard covering the essential requirements
of article 3.2 of the Directive 2014/53/EU
---------------------- Page: 3 ----------------------
SIST EN 302 372 V2.1.1:2017
2 ETSI EN 302 372 V2.1.1 (2016-12)
Reference
REN/ERM-TGUWB-131
Keywords
EHF, harmonised standard, radar, regulation,
SHF, short range, SRD, testing, UWB
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2016.
All rights reserved.
TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.
TM
3GPP and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI
---------------------- Page: 4 ----------------------
SIST EN 302 372 V2.1.1:2017
3 ETSI EN 302 372 V2.1.1 (2016-12)
Contents
Intellectual Property Rights . 8
Foreword . 8
Modal verbs terminology . 8
Introduction . 8
1 Scope . 10
2 References . 10
2.1 Normative references . 10
2.2 Informative references . 11
3 Definitions, symbols and abbreviations . 12
3.1 Definitions . 12
3.2 Symbols . 13
3.3 Abbreviations . 14
4 Technical requirements specifications . 15
4.1 Environmental conditions . 15
4.2 General . 15
4.3 Transmitter conformance requirements . 15
4.3.1 Permitted frequency range of operation . 15
4.3.1.1 Applicability. 15
4.3.1.2 Description . 15
4.3.1.3 Limits . 15
4.3.1.4 Conformance . 15
4.3.2 Operating bandwidth. 16
4.3.2.1 Applicability. 16
4.3.2.2 Description . 16
4.3.2.3 Limits . 16
4.3.2.4 Conformance . 16
4.3.3 Maximum value of mean power spectral density . 16
4.3.4 Maximum value of peak power . 16
4.3.4.1 Applicability. 16
4.3.4.2 Description . 17
4.3.4.3 Limits . 17
4.3.4.4 Conformance . 17
4.3.5 Exterior limits . 17
4.3.6 Low duty cycle . 17
4.3.7 Other emissions . 17
4.3.8 Transmitter unwanted emissions . 17
4.3.8.1 Applicability. 17
4.3.8.2 Description . 17
4.3.8.3 Limits . 18
4.3.8.4 Conformance . 18
4.4 Receiver conformance requirements . 18
4.4.1 General . 18
4.4.2 Receiver spurious emissions . 18
4.4.2.1 Applicability. 18
4.4.2.2 Description . 18
4.4.2.3 Limits . 18
4.4.2.4 Conformance . 19
4.4.3 Interferer signal handling . 19
4.4.3.1 Applicability. 19
4.4.3.2 Description . 19
4.4.3.3 Limits . 19
4.4.3.4 Conformance . 20
4.5 Requirements for spectrum access . 20
4.5.1 Detect and avoid (DAA) . 20
ETSI
---------------------- Page: 5 ----------------------
SIST EN 302 372 V2.1.1:2017
4 ETSI EN 302 372 V2.1.1 (2016-12)
4.5.2 Listen-before-talk (LBT) . 20
4.5.3 Low duty cycle (LDC) . 20
4.6 Antenna requirements . 20
4.7 Other requirements and mitigation techniques . 20
4.7.1 General . 20
4.7.2 Adaptive power control (APC) . 21
4.7.3 Activity factor and duty cycle . 21
4.7.3.1 Applicability. 21
4.7.3.2 Description . 21
4.7.3.3 Limits . 22
4.7.3.4 Conformance . 22
4.7.4 Frequency domain mitigation . 22
4.7.4.1 Applicability. 22
4.7.4.2 Description . 23
4.7.4.3 Limits . 23
4.7.4.4 Conformance . 23
4.7.5 Shielding effects . 23
4.7.5.1 Applicability. 23
4.7.5.2 Description . 23
4.7.5.3 Limits . 23
4.7.5.4 Conformance . 23
4.7.6 Thermal radiation . 23
4.7.7 Site registration . 23
4.7.8 Equivalent mitigation techniques . 23
4.7.8.1 Applicability. 23
4.7.8.2 Description . 24
4.7.8.3 Limits . 24
4.7.8.4 Conformance . 24
4.7.9 Range of modulation parameters . 24
4.7.9.1 Applicability. 24
4.7.9.2 Description . 24
4.7.9.3 Limits . 24
4.7.9.4 Conformance . 24
5 Testing for compliance with technical requirements . 24
5.1 Environmental conditions for testing . 24
5.2 General conditions for testing . 25
5.2.1 Product information . 25
5.2.2 Product information useful to facilitate testing . 25
5.2.3 Requirements for the test modulation . 25
5.2.4 Test conditions, power supply and ambient temperatures . 25
5.2.5 Choice of equipment for test suites . 25
5.2.6 Multiple operating bandwidths and multiband equipment . 26
5.2.7 Testing of host connected equipment and plug-in radio devices . 26
5.2.8 Radiated measurement arrangements. 26
5.3 Interpretation of the measurement results . 26
5.3.1 General . 26
5.3.2 Conversion loss data and measurement uncertainty . 27
5.3.3 Measurement uncertainty is equal to or less than maximum acceptable uncertainty . 28
5.3.4 Measurement uncertainty is greater than maximum acceptable uncertainty . 28
5.3.5 Emissions . 28
6 Conformance test suite . 28
6.1 Introduction . 28
6.2 Initial measurement steps . 28
6.3 Radiated measurements . 29
6.3.1 General . 29
6.3.2 Test sites and general arrangements for measurements involving the use of radiated fields . 29
6.3.3 Guidance on the use of a radiation test site . 29
6.3.4 Coupling of signals . 29
6.3.5 Standard test methods . 29
6.3.6 Standard calibration method . 29
ETSI
---------------------- Page: 6 ----------------------
SIST EN 302 372 V2.1.1:2017
5 ETSI EN 302 372 V2.1.1 (2016-12)
6.4 Conducted measurements . 29
6.4.1 General Setup . 29
6.4.2 Specific Setup . 29
6.5 Conformance test suite for transmitter parameters . 29
6.5.1 General . 29
6.5.2 Method of measurements of the Ultra-Wideband emissions . 30
6.5.3 Permitted frequency range of operation . 30
6.5.4 Operating bandwidth. 30
6.5.5 Mean power spectral density measurements . 31
6.5.6 Peak power measurements . 34
6.5.6.1 Description . 34
6.5.6.2 Radiated test procedure . 35
6.5.6.3 Conducted test procedure . 35
6.5.7 Exterior limit measurement. 35
6.5.8 Total Power . 35
6.5.9 Other Emissions . 35
6.6 Conformance test suite for receiver parameters . 35
6.6.1 Receiver spurious emissions . 35
6.6.2 Receiver sensitivity . 35
6.6.3 Interferer signal handling . 35
6.6.3.1 Description . 35
6.6.3.2 Interferer frequencies and power levels . 35
6.6.3.3 Real scenario . 36
6.6.3.4 Equivalent scenario . 37
6.6.3.5 Radiated test setup for the equivalent scenario . 37
6.6.3.6 Conducted test setup for the equivalent scenario . 40
6.6.3.7 Test procedure for the equivalent scenario . 41
6.6.3.8 Alternative scenario . 42
6.6.3.9 Radiated test setup for the alternative scenario . 42
6.6.3.10 Conducted test setup for the alternative scenario . 43
6.6.3.11 Test procedure for the alternative scenario . 44
6.7 Conformance test suites for spectrum access . 45
6.7.1 Detect and avoid mechanisms . 45
6.7.2 Listen before talk . 45
6.7.3 Low duty cycle . 45
6.8 Conformance test suites for antenna requirements . 45
6.9 Other test suites . 45
6.9.1 Adaptive power control (APC) . 45
6.9.2 Activity factor and duty cycle . 45
6.9.3 Frequency domain mitigation . 45
6.9.4 Shielding effects . 45
6.9.5 Thermal radiations . 46
6.9.6 Site registration . 46
Annex A (normative): Relationship between the present document and the essential
requirements of Directive 2014/53/EU . 47
Annex B (informative): Application form for testing . 48
B.1 Introduction . 48
B.2 General information as required by ETSI EN 302 372, clause 5.2 . 48
B.2.1 Type of equipment (stand-alone, combined, plug-in radio device,
...
ETSI EN 302 372 V2.1.1 (2016-12)
HARMONISED EUROPEAN STANDARD
Short Range Devices (SRD);
Tank Level Probing Radar (TLPR) equipment operating in the
frequency ranges 4,5 GHz to 7 GHz, 8,5 GHz to 10,6 GHz,
24,05 GHz to 27 GHz, 57 GHz to 64 GHz, 75 GHz to 85 GHz;
Harmonised Standard covering the essential requirements
of article 3.2 of the Directive 2014/53/EU
---------------------- Page: 1 ----------------------
2 ETSI EN 302 372 V2.1.1 (2016-12)
Reference
REN/ERM-TGUWB-131
Keywords
EHF, harmonised standard, radar, regulation,
SHF, short range, SRD, testing, UWB
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2016.
All rights reserved.
TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.
TM
3GPP and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI
---------------------- Page: 2 ----------------------
3 ETSI EN 302 372 V2.1.1 (2016-12)
Contents
Intellectual Property Rights . 8
Foreword . 8
Modal verbs terminology . 8
Introduction . 8
1 Scope . 10
2 References . 10
2.1 Normative references . 10
2.2 Informative references . 11
3 Definitions, symbols and abbreviations . 12
3.1 Definitions . 12
3.2 Symbols . 13
3.3 Abbreviations . 14
4 Technical requirements specifications . 15
4.1 Environmental conditions . 15
4.2 General . 15
4.3 Transmitter conformance requirements . 15
4.3.1 Permitted frequency range of operation . 15
4.3.1.1 Applicability. 15
4.3.1.2 Description . 15
4.3.1.3 Limits . 15
4.3.1.4 Conformance . 15
4.3.2 Operating bandwidth. 16
4.3.2.1 Applicability. 16
4.3.2.2 Description . 16
4.3.2.3 Limits . 16
4.3.2.4 Conformance . 16
4.3.3 Maximum value of mean power spectral density . 16
4.3.4 Maximum value of peak power . 16
4.3.4.1 Applicability. 16
4.3.4.2 Description . 17
4.3.4.3 Limits . 17
4.3.4.4 Conformance . 17
4.3.5 Exterior limits . 17
4.3.6 Low duty cycle . 17
4.3.7 Other emissions . 17
4.3.8 Transmitter unwanted emissions . 17
4.3.8.1 Applicability. 17
4.3.8.2 Description . 17
4.3.8.3 Limits . 18
4.3.8.4 Conformance . 18
4.4 Receiver conformance requirements . 18
4.4.1 General . 18
4.4.2 Receiver spurious emissions . 18
4.4.2.1 Applicability. 18
4.4.2.2 Description . 18
4.4.2.3 Limits . 18
4.4.2.4 Conformance . 19
4.4.3 Interferer signal handling . 19
4.4.3.1 Applicability. 19
4.4.3.2 Description . 19
4.4.3.3 Limits . 19
4.4.3.4 Conformance . 20
4.5 Requirements for spectrum access . 20
4.5.1 Detect and avoid (DAA) . 20
ETSI
---------------------- Page: 3 ----------------------
4 ETSI EN 302 372 V2.1.1 (2016-12)
4.5.2 Listen-before-talk (LBT) . 20
4.5.3 Low duty cycle (LDC) . 20
4.6 Antenna requirements . 20
4.7 Other requirements and mitigation techniques . 20
4.7.1 General . 20
4.7.2 Adaptive power control (APC) . 21
4.7.3 Activity factor and duty cycle . 21
4.7.3.1 Applicability. 21
4.7.3.2 Description . 21
4.7.3.3 Limits . 22
4.7.3.4 Conformance . 22
4.7.4 Frequency domain mitigation . 22
4.7.4.1 Applicability. 22
4.7.4.2 Description . 23
4.7.4.3 Limits . 23
4.7.4.4 Conformance . 23
4.7.5 Shielding effects . 23
4.7.5.1 Applicability. 23
4.7.5.2 Description . 23
4.7.5.3 Limits . 23
4.7.5.4 Conformance . 23
4.7.6 Thermal radiation . 23
4.7.7 Site registration . 23
4.7.8 Equivalent mitigation techniques . 23
4.7.8.1 Applicability. 23
4.7.8.2 Description . 24
4.7.8.3 Limits . 24
4.7.8.4 Conformance . 24
4.7.9 Range of modulation parameters . 24
4.7.9.1 Applicability. 24
4.7.9.2 Description . 24
4.7.9.3 Limits . 24
4.7.9.4 Conformance . 24
5 Testing for compliance with technical requirements . 24
5.1 Environmental conditions for testing . 24
5.2 General conditions for testing . 25
5.2.1 Product information . 25
5.2.2 Product information useful to facilitate testing . 25
5.2.3 Requirements for the test modulation . 25
5.2.4 Test conditions, power supply and ambient temperatures . 25
5.2.5 Choice of equipment for test suites . 25
5.2.6 Multiple operating bandwidths and multiband equipment . 26
5.2.7 Testing of host connected equipment and plug-in radio devices . 26
5.2.8 Radiated measurement arrangements. 26
5.3 Interpretation of the measurement results . 26
5.3.1 General . 26
5.3.2 Conversion loss data and measurement uncertainty . 27
5.3.3 Measurement uncertainty is equal to or less than maximum acceptable uncertainty . 28
5.3.4 Measurement uncertainty is greater than maximum acceptable uncertainty . 28
5.3.5 Emissions . 28
6 Conformance test suite . 28
6.1 Introduction . 28
6.2 Initial measurement steps . 28
6.3 Radiated measurements . 29
6.3.1 General . 29
6.3.2 Test sites and general arrangements for measurements involving the use of radiated fields . 29
6.3.3 Guidance on the use of a radiation test site . 29
6.3.4 Coupling of signals . 29
6.3.5 Standard test methods . 29
6.3.6 Standard calibration method . 29
ETSI
---------------------- Page: 4 ----------------------
5 ETSI EN 302 372 V2.1.1 (2016-12)
6.4 Conducted measurements . 29
6.4.1 General Setup . 29
6.4.2 Specific Setup . 29
6.5 Conformance test suite for transmitter parameters . 29
6.5.1 General . 29
6.5.2 Method of measurements of the Ultra-Wideband emissions . 30
6.5.3 Permitted frequency range of operation . 30
6.5.4 Operating bandwidth. 30
6.5.5 Mean power spectral density measurements . 31
6.5.6 Peak power measurements . 34
6.5.6.1 Description . 34
6.5.6.2 Radiated test procedure . 35
6.5.6.3 Conducted test procedure . 35
6.5.7 Exterior limit measurement. 35
6.5.8 Total Power . 35
6.5.9 Other Emissions . 35
6.6 Conformance test suite for receiver parameters . 35
6.6.1 Receiver spurious emissions . 35
6.6.2 Receiver sensitivity . 35
6.6.3 Interferer signal handling . 35
6.6.3.1 Description . 35
6.6.3.2 Interferer frequencies and power levels . 35
6.6.3.3 Real scenario . 36
6.6.3.4 Equivalent scenario . 37
6.6.3.5 Radiated test setup for the equivalent scenario . 37
6.6.3.6 Conducted test setup for the equivalent scenario . 40
6.6.3.7 Test procedure for the equivalent scenario . 41
6.6.3.8 Alternative scenario . 42
6.6.3.9 Radiated test setup for the alternative scenario . 42
6.6.3.10 Conducted test setup for the alternative scenario . 43
6.6.3.11 Test procedure for the alternative scenario . 44
6.7 Conformance test suites for spectrum access . 45
6.7.1 Detect and avoid mechanisms . 45
6.7.2 Listen before talk . 45
6.7.3 Low duty cycle . 45
6.8 Conformance test suites for antenna requirements . 45
6.9 Other test suites . 45
6.9.1 Adaptive power control (APC) . 45
6.9.2 Activity factor and duty cycle . 45
6.9.3 Frequency domain mitigation . 45
6.9.4 Shielding effects . 45
6.9.5 Thermal radiations . 46
6.9.6 Site registration . 46
Annex A (normative): Relationship between the present document and the essential
requirements of Directive 2014/53/EU . 47
Annex B (informative): Application form for testing . 48
B.1 Introduction . 48
B.2 General information as required by ETSI EN 302 372, clause 5.2 . 48
B.2.1 Type of equipment (stand-alone, combined, plug-in radio device, etc.) . 48
B.2.2 The nominal voltages of the stand-alone radio equipment or the nominal voltages of the combined
(host) equipment or test jig in case of plug-in devices . 48
B.3 Signal related information as required by ETSI EN 302 372, clause 4.3 . 49
B.3.1 Introduction . 49
B.3.2 Operational frequency range(s) of the equipment . 49
B.3.3 Nominal channel bandwidth(s) . 49
B.3.4 The type of modulation used by the equipment. 49
B.3.5 The worst case mode for each of the following tests . 49
ETSI
---------------------- Page: 5 ----------------------
...
Final draft ETSI EN 302 372 V2.1.1 (2016-10)
HARMONISED EUROPEAN STANDARD
Short Range Devices (SRD);
Tank Level Probing Radar (TLPR) equipment operating in the
frequency ranges 4,5 GHz to 7 GHz, 8,5 GHz to 10,6 GHz,
24,05 GHz to 27 GHz, 57 GHz to 64 GHz, 75 GHz to 85 GHz;
Harmonised Standard covering the essential requirements
of article 3.2 of the Directive 2014/53/EU
---------------------- Page: 1 ----------------------
2 Final draft ETSI EN 302 372 V2.1.1 (2016-10)
Reference
REN/ERM-TGUWB-131
Keywords
EHF, harmonised standard, radar, regulation,
SHF, short range, SRD, testing, UWB
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2016.
All rights reserved.
TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.
TM
3GPP and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI
---------------------- Page: 2 ----------------------
3 Final draft ETSI EN 302 372 V2.1.1 (2016-10)
Contents
Intellectual Property Rights . 8
Foreword . 8
Modal verbs terminology . 8
Introduction . 8
1 Scope . 10
2 References . 11
2.1 Normative references . 11
2.2 Informative references . 11
3 Definitions, symbols and abbreviations . 12
3.1 Definitions . 12
3.2 Symbols . 13
3.3 Abbreviations . 14
4 Technical requirements specifications . 15
4.1 Environmental conditions . 15
4.2 General . 15
4.3 Transmitter conformance requirements . 15
4.3.1 Permitted frequency range of operation . 15
4.3.1.1 Applicability. 15
4.3.1.2 Description . 15
4.3.1.3 Limits . 15
4.3.1.4 Conformance . 16
4.3.2 Operating bandwidth. 16
4.3.2.1 Applicability. 16
4.3.2.2 Description . 16
4.3.2.3 Limits . 16
4.3.2.4 Conformance . 16
4.3.3 Maximum value of mean power spectral density . 17
4.3.4 Maximum value of peak power . 17
4.3.4.1 Applicability. 17
4.3.4.2 Description . 17
4.3.4.3 Limits . 17
4.3.4.4 Conformance . 17
4.3.5 Exterior limits . 17
4.3.6 Low duty cycle . 17
4.3.7 Other emissions . 17
4.3.8 Transmitter unwanted emissions . 18
4.3.8.1 Applicability. 18
4.3.8.2 Description . 18
4.3.8.3 Limits . 18
4.3.8.4 Conformance . 18
4.4 Receiver conformance requirements . 18
4.4.1 General . 18
4.4.2 Receiver spurious emissions . 18
4.4.2.1 Applicability. 18
4.4.2.2 Description . 19
4.4.2.3 Limits . 19
4.4.2.4 Conformance . 19
4.4.3 Interferer signal handling . 19
4.4.3.1 Applicability. 19
4.4.3.2 Description . 19
4.4.3.3 Limits . 20
4.4.3.4 Conformance . 20
4.5 Requirements for spectrum access . 20
4.5.1 Detect and avoid (DAA) . 20
ETSI
---------------------- Page: 3 ----------------------
4 Final draft ETSI EN 302 372 V2.1.1 (2016-10)
4.5.2 Listen-before-talk (LBT) . 20
4.5.3 Low duty cycle (LDC) . 21
4.6 Antenna requirements . 21
4.7 Other requirements and mitigation techniques . 21
4.7.1 General . 21
4.7.2 Adaptive power control (APC) . 21
4.7.3 Activity factor and duty cycle . 21
4.7.3.1 Applicability. 21
4.7.3.2 Description . 21
4.7.3.3 Limits . 22
4.7.3.4 Conformance . 22
4.7.4 Frequency domain mitigation . 23
4.7.4.1 Applicability. 23
4.7.4.2 Description . 23
4.7.4.3 Limits . 23
4.7.4.4 Conformance . 23
4.7.5 Shielding effects . 23
4.7.5.1 Applicability. 23
4.7.5.2 Description . 23
4.7.5.3 Limits . 23
4.7.5.4 Conformance . 23
4.7.6 Thermal radiation . 23
4.7.7 Site registration . 23
4.7.8 Equivalent mitigation techniques . 24
4.7.8.1 Applicability. 24
4.7.8.2 Description . 24
4.7.8.3 Limits . 24
4.7.8.4 Conformance . 24
4.7.9 Range of modulation parameters . 24
4.7.9.1 Applicability. 24
4.7.9.2 Description . 24
4.7.9.3 Limits . 24
4.7.9.4 Conformance . 24
5 Testing for compliance with technical requirements . 25
5.1 Environmental conditions for testing . 25
5.2 General conditions for testing . 25
5.2.1 Product information . 25
5.2.2 Product information useful to facilitate testing . 25
5.2.3 Requirements for the test modulation . 25
5.2.4 Test conditions, power supply and ambient temperatures . 25
5.2.5 Choice of equipment for test suites . 25
5.2.6 Multiple operating bandwidths and multiband equipment . 26
5.2.7 Testing of host connected equipment and plug-in radio devices . 26
5.2.8 Radiated measurement arrangements. 26
5.3 Interpretation of the measurement results . 26
5.3.1 General . 26
5.3.2 Conversion loss data and measurement uncertainty . 27
5.3.3 Measurement uncertainty is equal to or less than maximum acceptable uncertainty . 28
5.3.4 Measurement uncertainty is greater than maximum acceptable uncertainty . 28
5.3.5 Emissions . 28
6 Conformance test suite . 28
6.1 Introduction . 28
6.2 Initial measurement steps . 28
6.3 Radiated measurements . 29
6.3.1 General . 29
6.3.2 Test sites and general arrangements for measurements involving the use of radiated fields . 29
6.3.3 Guidance on the use of a radiation test site . 29
6.3.4 Coupling of signals . 29
6.3.5 Standard test methods . 29
6.3.6 Standard calibration method . 29
ETSI
---------------------- Page: 4 ----------------------
5 Final draft ETSI EN 302 372 V2.1.1 (2016-10)
6.4 Conducted measurements . 29
6.4.1 General Setup . 29
6.4.2 Specific Setup . 29
6.5 Conformance test suite for transmitter parameters . 29
6.5.1 General . 29
6.5.2 Method of measurements of the Ultra-Wideband emissions . 30
6.5.3 Permitted frequency range of operation . 30
6.5.4 Operating bandwidth. 30
6.5.5 Mean power spectral density measurements . 32
6.5.6 Peak power measurements . 34
6.5.6.1 Description . 34
6.5.6.2 Radiated test procedure . 35
6.5.6.3 Conducted test procedure . 35
6.5.7 Exterior limit measurement. 35
6.5.8 Total Power . 35
6.5.9 Other Emissions . 35
6.6 Conformance test suite for receiver parameters . 35
6.6.1 Receiver spurious emissions . 35
6.6.2 Receiver sensitivity . 35
6.6.3 Interferer signal handling . 35
6.6.3.1 Description . 35
6.6.3.2 Interferer frequencies and power levels . 35
6.6.3.3 Real scenario . 36
6.6.3.4 Equivalent scenario . 37
6.6.3.5 Radiated test setup for the equivalent scenario . 37
6.6.3.6 Conducted test setup for the equivalent scenario . 40
6.6.3.7 Test procedure for the equivalent scenario . 41
6.6.3.8 Alternative scenario . 42
6.6.3.9 Radiated test setup for the alternative scenario . 42
6.6.3.10 Conducted test setup for the alternative scenario . 43
6.6.3.11 Test procedure for the alternative scenario . 44
6.7 Conformance test suites for spectrum access . 45
6.7.1 Detect and avoid mechanisms . 45
6.7.2 Listen before talk . 45
6.7.3 Low duty cycle . 45
6.8 Conformance test suites for antenna requirements . 45
6.9 Other test suites . 45
6.9.1 Adaptive power control (APC) . 45
6.9.2 Activity factor and duty cycle . 45
6.9.3 Frequency domain mitigation . 45
6.9.4 Shielding effects . 45
6.9.5 Thermal radiations . 46
6.9.6 Site registration . 46
Annex A (normative): Relationship between the present document and the essential
requirements of Directive 2014/53/EU . 47
Annex B (informative): Application form for testing . 48
B.1 Introduction . 48
B.2 General information as required by ETSI EN 302 372, clause 5.2 . 48
B.2.1 Type of equipment (stand-alone, combined, plug-in radio device, etc.) . 48
B.2.2 The nominal voltages of the stand-alone radio equipment or the nominal voltages of the combined
(host) equipment or test jig in case of plug-in devices . 48
B.3 Signal related information as required by ETSI EN 302 372, clause 4.3 . 49
B.3.1 Introduction . 49
B.3.2 Operational frequency range(s) of the equipment . 49
B.3.3 Nominal channel bandwidth(s) . 49
B.3.4 The type of modulation used by the equipment. 49
B.3.5 The worst case mode for each of the following tests . 49
ETSI
...
Draft ETSI EN 302 372 V2.1.0 (2016-04)
HARMONISED EUROPEAN STANDARD
Short Range Devices (SRD);
Tank Level Probing Radar (TLPR) equipment operating in the
frequency ranges 4,5 GHz to 7 GHz, 8,5 GHz to 10,6 GHz,
24,05 GHz to 27 GHz, 57 GHz to 64 GHz, 75 GHz to 85 GHz;
Harmonised Standard covering the essential requirements
of article 3.2 of the Directive 2014/53/EU
---------------------- Page: 1 ----------------------
2 Draft ETSI EN 302 372 V2.1.0 (2016-04)
Reference
REN/ERM-TGUWB-131
Keywords
EHF, harmonised standard, radar, regulation,
SHF, short range, SRD, testing, UWB
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2016.
All rights reserved.
TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.
TM
3GPP and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI
---------------------- Page: 2 ----------------------
3 Draft ETSI EN 302 372 V2.1.0 (2016-04)
Contents
Intellectual Property Rights . 8
Foreword . 8
Modal verbs terminology . 8
Introduction . 8
1 Scope . 10
2 References . 11
2.1 Normative references . 11
2.2 Informative references . 11
3 Definitions, symbols and abbreviations . 12
3.1 Definitions . 12
3.2 Symbols . 13
3.3 Abbreviations . 14
4 Technical requirements specifications . 15
4.1 Environmental conditions . 15
4.2 General . 15
4.3 Transmitter conformance requirements . 15
4.3.1 Permitted frequency range of operation . 15
4.3.1.1 Applicability. 15
4.3.1.2 Description . 15
4.3.1.3 Limits . 15
4.3.1.4 Conformance . 16
4.3.2 Operating bandwidth. 16
4.3.2.1 Applicability. 16
4.3.2.2 Description . 16
4.3.2.3 Limits . 16
4.3.2.4 Conformance . 16
4.3.3 Maximum value of mean power spectral density . 17
4.3.4 Maximum value of peak power . 17
4.3.4.1 Applicability. 17
4.3.4.2 Description . 17
4.3.4.3 Limits . 17
4.3.4.4 Conformance . 17
4.3.5 Exterior limits . 17
4.3.6 Low duty cycle . 17
4.3.7 Other emissions . 17
4.3.8 Transmitter unwanted emissions . 17
4.3.8.1 Applicability. 17
4.3.8.2 Description . 18
4.3.8.3 Limits . 18
4.3.8.4 Conformance . 18
4.4 Receiver conformance requirements . 18
4.4.1 Receiver requirements . 18
4.4.2 Receiver spurious emissions . 18
4.4.2.1 Applicability. 18
4.4.2.2 Description . 18
4.4.2.3 Limits . 18
4.4.2.4 Conformance . 19
4.4.3 Interferer signal handling . 19
4.4.3.1 Applicability. 19
4.4.3.2 Description . 19
4.4.3.3 Limits . 20
4.4.3.4 Conformance . 20
4.5 Requirements for spectrum access . 20
4.5.1 Detect and avoid (DAA) . 20
ETSI
---------------------- Page: 3 ----------------------
4 Draft ETSI EN 302 372 V2.1.0 (2016-04)
4.5.2 Listen-before-talk (LBT) . 20
4.5.3 Low duty cycle (LDC) . 20
4.6 Antenna requirements . 20
4.7 Other requirements and mitigation techniques . 21
4.7.1 General . 21
4.7.2 Adaptive power control (APC) . 21
4.7.3 Activity factor and duty cycle . 21
4.7.3.1 Applicability. 21
4.7.3.2 Description . 21
4.7.3.3 Limits . 22
4.7.3.4 Conformance . 22
4.7.4 Frequency domain mitigation . 22
4.7.4.1 Applicability. 22
4.7.4.2 Description . 23
4.7.4.3 Limits . 23
4.7.4.4 Conformance . 23
4.7.5 Shielding effects . 23
4.7.5.1 Applicability. 23
4.7.5.2 Description . 23
4.7.5.3 Limits . 23
4.7.5.4 Conformance . 23
4.7.6 Thermal radiation . 23
4.7.7 Site registration . 23
4.7.8 Equivalent mitigation techniques . 23
4.7.8.1 Applicability. 23
4.7.8.2 Description . 23
4.7.8.3 Limits . 24
4.7.8.4 Conformance . 24
4.7.9 Range of modulation parameters . 24
4.7.9.1 Applicability. 24
4.7.9.2 Description . 24
4.7.9.3 Limits . 24
4.7.9.4 Conformance . 24
5 Testing for compliance with technical requirements . 24
5.1 Environmental conditions for testing . 24
5.2 General conditions for testing . 24
5.2.1 Product information . 24
5.2.2 Product information useful to facilitate testing . 24
5.2.3 Requirements for the test modulation . 25
5.2.4 Test conditions, power supply and ambient temperatures . 25
5.2.5 Choice of equipment for test suites . 25
5.2.6 Multiple operating bandwidths and multiband equipment . 25
5.2.7 Testing of host connected equipment and plug-in radio devices . 25
5.2.8 Radiated measurement arrangements. 26
5.3 Interpretation of the measurement results . 26
5.3.1 General . 26
5.3.2 Conversion loss data and measurement uncertainty . 27
5.3.3 Measurement uncertainty is equal to or less than maximum acceptable uncertainty . 28
5.3.4 Measurement uncertainty is greater than maximum acceptable uncertainty . 28
5.3.5 Emissions . 28
6 Conformance test suite . 28
6.1 Introduction . 28
6.2 Initial measurement steps . 28
6.3 Radiated measurements . 28
6.3.1 General . 28
6.3.2 Test sites and general arrangements for measurements involving the use of radiated fields . 29
6.3.3 Guidance on the use of a radiation test site . 29
6.3.4 Coupling of signals . 29
6.3.5 Standard test methods . 29
6.3.6 Standard calibration method . 29
ETSI
---------------------- Page: 4 ----------------------
5 Draft ETSI EN 302 372 V2.1.0 (2016-04)
6.4 Conducted measurements . 29
6.4.1 General Setup . 29
6.4.2 Specific Setup . 29
6.5 Conformance test suite for transmitter parameters . 29
6.5.1 General . 29
6.5.2 Method of measurements of the Ultra-Wideband emissions . 29
6.5.3 Permitted frequency range of operation . 29
6.5.4 Operating bandwidth. 30
6.5.5 Mean power spectral density measurements . 31
6.5.6 Peak power measurements . 33
6.5.6.1 Description . 33
6.5.6.2 Radiated test procedure . 34
6.5.6.3 Conducted test procedure . 34
6.5.7 Exterior limit measurement. 34
6.5.8 Total Power . 34
6.5.9 Other Emissions . 34
6.6 Conformance test suite for receiver parameters . 34
6.6.1 Receiver spurious emissions . 34
6.6.2 Receiver sensitivity . 34
6.6.3 Interferer signal handling . 35
6.6.3.1 Description . 35
6.6.3.2 Interferer frequencies and power levels . 35
6.6.3.3 Real scenario . 35
6.6.3.4 Equivalent scenario . 36
6.6.3.5 Radiated test setup for the equivalent scenario . 36
6.6.3.6 Conducted test setup for the equivalent scenario . 39
6.6.3.7 Test procedure for the equivalent scenario . 40
6.6.3.8 Alternative scenario . 41
6.6.3.9 Radiated test setup for the alternative scenario . 42
6.6.3.10 Conducted test setup for the alternative scenario . 42
6.6.3.11 Test procedure for the alternative scenario . 43
6.7 Conformance test suites for spectrum access . 43
6.7.1 Detect and avoid mechanisms . 43
6.7.2 Listen before talk . 44
6.7.3 Low duty cycle . 44
6.8 Conformance test suites for antenna requirements . 44
6.9 Other test suites . 44
6.9.1 Adaptive power control (APC) . 44
6.9.2 Activity factor and duty cycle . 44
6.9.3 Frequency domain mitigation . 44
6.9.4 Shielding effects . 44
6.9.5 Thermal radiations . 44
6.9.6 Site registration . 44
Annex A (normative): Relationship between the present document and the essential
requirements of Directive 2014/53/EU . 45
Annex B (informative): Application form for testing . 46
B.1 Introduction . 46
B.2 General information as required by ETSI EN 302 372, clause 5.2 . 46
B.2.1 Type of equipment (stand-alone, combined, plug-in radio device, etc.) . 46
B.2.2 The nominal voltages of the stand-alone radio equipment or the nominal voltages of the combined
(host) equipment or test jig in case of plug-in devices . 46
B.3 Signal related information as required by ETSI EN 302 372, clause 5.3 . 47
B.3.1 Introduction . 47
B.3.2 Operational frequency range(s) of the equipment . 47
B.3.3 Nominal channel bandwidth(s) . 47
B.3.4 The type of modulation used by the equipment. 47
B.3.5 The worst case mode for each of the following tests . 47
ETSI
---------------------- Page: 5 ---
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.