SIST EN 232:2003
(Main)Baths - Connecting dimensions
Baths - Connecting dimensions
This European standard specifies the connecting dimensions for baths, regardless of the material. Note: only dimensions are compulsory. The shape of the appliance in the figure is for illustration only; it in no way prejudices the final shape of the appliance which is left to the initiative of the manufacturer.
Badewannen - Anschlussmaße
Baignoires - Cotes de raccordement
La présente norme spécifie les exigences relatives aux cotes de raccordement des baignoires, quels que soient les matériaux entrant dans leur fabrication.
NOTE Seules les dimensions doivent etre respectées. La forme des appareils représentée dans les figures est donnée uniquement a titre d'illustration ; elle ne préjuge en rien de la forme définitive de l'appareil qui est laissée a l'initiative du fabricant.
Kopalne kadi - Priključne mere
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 232:2003
01-oktober-2003
1DGRPHãþD
SIST EN 232:1998
.RSDOQHNDGL3ULNOMXþQHPHUH
Baths - Connecting dimensions
Badewannen - Anschlussmaße
Baignoires - Cotes de raccordement
Ta slovenski standard je istoveten z: EN 232:2003
ICS:
91.140.70 Sanitarne naprave Sanitary installations
SIST EN 232:2003 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
EUROPEAN STANDARD
EN 232
NORME EUROPÉENNE
EUROPÄISCHE NORM
May 2003
ICS 91.140.70 Supersedes EN 232:1990
English version
Baths - Connecting dimensions
Baignoires - Cotes de raccordement Badewannen - Anschlussmaße
This European Standard was approved by CEN on 17 January 2003.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and United
Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2003 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 232:2003 E
worldwide for CEN national Members.
---------------------- Page: 2 ----------------------
EN 232:2003 (E)
Contents Page
Foreword.3
1 Scope .4
2 Normative references .4
3 Connecting dimensions .4
3.1 Basic dimensions .4
3.2 Dimensions of the waste outlet hole .6
3.3 Clearance around the waste outlet hole.7
3.4 Dimensions and clearance around the overflow hole .8
3.5 Dimensions and clearance around tapholes .9
Annex A (normative) Determination of dimensions .10
A.1 Test apparatus.10
A.2 Determination of the fit of the control gauge in the waste outlet hole.10
2
---------------------- Page: 3 ----------------------
EN 232:2003 (E)
Foreword
This document (EN 232:2003) has been prepared by Technical Committee CEN/TC 163, "Sanitary Appliances", the
secretariat of which is held by UNI.
This European Standard shall be given the status of a national standard, either by publication of an identical text or
by endorsement, at the latest by November 2003, and conflicting national standards shall be withdrawn at the latest
by November 2003.
This document supersedes EN 232:1990.
This European Standard applies to baths used for domestic purposes and complements the standards for baths
made from different materials, the existing standards on tap ware and waste fittings (EN 200 and EN 274-1) in
terms of their dimensional requirements.
Annex A is normative.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal,
Slovakia, Spain, Sweden, Switzerland and the United Kingdom.
3
---------------------- Page: 4 ----------------------
EN 232:2003 (E)
1 Scope
This standard specifies requirements for the connecting dimensions of baths, regardless of the material used for
their manufacture.
NOTE Only dimensions are compulsory. The shape of the appliance in the figures is for illustration only; it in no way
prejudices the shape of the appliance which is left to the initiative of the manufacturer.
2 Normative references
This European Standard incorporates by dated or undated reference, provisions from other publications. These
normative references are cited at the appropriate places in the text and the publications are listed hereafter. For
dated references, subsequent amendments to or revisions of any of these publications apply to this European
Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the
publication referred to applies (including amendments).
EN 274-1, Waste fittings for sanitary appliances– Part 1: Requirements
3 Connecting dimensions
3.1 Basic dimensions
The basic dimensions H, a, H and h shall comply with Table 1 to enable compatibility with EN 274-1.
1 1
4
--------------------
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.