SIST-TP CEN ISO/TR 20573:2008

Footwear - Performance requirements for components for footwear - Heels and top pieces (ISO/TR 20573:2006)

ISO/TR 20573:2006 establishes the performance requirements for heel and top piece components for footwear (not for finished footwear), irrespective of the material, in order to assess the suitability for the end use and/or fitness for purpose.
It also establishes the test methods used to evaluate the compliance with the requirements.
ISO/TR 20573:2006 applies to heel and top piece for all kind of footwear.
ISO/TR 20573:2006 is intended to be used as a reference between the manufacturer and the supplier. It is not intended for third party certification of finished footwear intended for the consumer.

Schuhe - Anforderungen an das Gebrauchsverhalten von Schuhbestandteilen - Absätze und Oberflecken (ISO/TR 20573:2006)

Dieser Technische Bericht führt die Anforderungen an das Gebrauchsverhalten für Absätze und Oberflecken für Schuhe (nicht für fertige Schuhe) unabhängig vom Material ein, um die Eignung für den vorgesehenen Verwendungszweck und/oder die Gebrauchstauglichkeit zu bewerten.
Er führt ebenfalls die Prüfverfahren zur Bewertung der Konformität mit den Anforderungen ein.
Dieser Technische Bericht gilt für Absätze und Oberflecken für jede Art von Schuhen wie in Abschnitt 3 definiert.
Dieser Technische Bericht ist als Bezug zwischen Hersteller und Lieferant vorgesehen. Er ist nicht für die Drittstellen¬zertifizierung von fertigen Schuhen für den Verbraucher vorgesehen.

Chaussures - Exigences de performance pour les composants des chaussures - Talons et bonbouts (ISO/TR 20573:2006)

Obutev - Zahtevane lastnosti za dele obutve - Pete in vrhnji kosi (ISO/TR 20573:2006)

General Information

• Status: Published
• Publication Date: 10-Sep-2008
• ICS: 61.060 - Footwear
• Technical Committee: I13 - Imaginarni 13
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 26-Aug-2008
• Due Date: 31-Oct-2008
• Completion Date: 11-Sep-2008
• Ref Project: CEN ISO/TR 20573:2008 - Footwear - Performance requirements for components for footwear - Heels and top pieces (ISO/TR 20573:2006)

Standards Content (Sample)

SLOVENSKI STANDARD
01-oktober-2008
Obutev - Zahtevane lastnosti za dele obutve - Pete in vrhnji kosi (ISO/TR
20573:2006)
Footwear - Performance requirements for components for footwear - Heels and top
pieces (ISO/TR 20573:2006)
Schuhe - Anforderungen an das Gebrauchsverhalten von Schuhbestandteilen - Absätze
und Oberflecken (ISO/TR 20573:2006)
Chaussures - Exigences de performance pour les composants des chaussures - Talons
et bonbouts (ISO/TR 20573:2006)
Ta slovenski standard je istoveten z: CEN ISO/TR 20573:2008
ICS:
61.060 Obuvala Footwear
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

TECHNICAL REPORT
CEN ISO/TR 20573
RAPPORT TECHNIQUE
TECHNISCHER BERICHT
July 2008
ICS 61.060
English Version
Footwear - Performance requirements for components for
footwear - Heels and top pieces (ISO/TR 20573:2006)
Chaussures - Exigences de performance pour les Schuhe - Anforderungen an das Gebrauchsverhalten von
composants des chaussures - Talons et bonbouts (ISO/TR Schuhbestandteilen - Absätze und Oberflecken (ISO/TR
20573:2006) 20573:2006)
This Technical Report was approved by CEN on 14 April 2008. It has been drawn up by the Technical Committee CEN/TC 309.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2008 CEN All rights of exploitation in any form and by any means reserved Ref. No. CEN ISO/TR 20573:2008: E
worldwide for CEN national Members.

Contents Page
Foreword.3

Foreword
The text of ISO/TR 20573:2006 has been prepared by Technical Committee ISO/TC 216 “Footwear” of the
International Organization for Standardization (ISO) and has been taken over as CEN ISO/TR 20573:2008 by
Technical Committee CEN/TC 309 “Footwear” the secretariat of which is held by AENOR.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
Endorsement notice
The text of ISO/TR 20573:2006 has been approved by CEN as a CEN ISO/TR 20573:2008 without any
modification.
TECHNICAL ISO/TR
REPORT 20573
First edition
2006-12-01
Footwear — Performance requirements
for components for footwear — Heels and
top pieces
Chaussures — Exigences de performance pour les composants des
chaussures — Talons et bonbouts

Reference number
ISO/TR 20573:2006(E)
©
ISO 2006
ISO/TR 20573:2006(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.

©  ISO 2006
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail [e-mail]
Web www.iso.org
Published in Switzerland
ii © ISO 2006 – All rights reserved

ISO/TR 20573:2006(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
In exceptional circumstances, when a technical committee has collected data of a different kind from that
which is normally published as an International Standard (“state of the art”, for example), it may decide by a
simple majority vote of its participating members to publish a Technical Report. A Technical Report is entirely
informative in nature and does not have to be reviewed until the data it provides are considered to be no
longer valid or useful.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO/TR 20573 was prepared by Technical Committee ISO/TC 216, Footwear.

TECHNICAL REPORT ISO/TR 20573:2006(E)

Footwear — Performance requirements for components for
footwear — Heels and top pieces
1 Scope
This Technical Report establishes the performance requirements for heel and top piece components for
footwear (not for finished footwear), irrespective of the material, in order to assess the suitability for the end
use and/or fitness for purpose.
It also establishes the test methods used to evaluate the compliance with the requirements.
This Technical Report applies to heel and top piece for all kind of footwear as defined in Clause 3.
This Technical Report is intended to be used as a reference between the manufacturer and the supplier. It is
not intended for third party certification of finished footwear intended for the consumer.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 31-0, Quantities and units — Part 0: General Principles
EN 12770, Footwear — Test methods for outsoles — Abrasion resistance
EN 13287, Personal protective equipment — Footwear — Test method for slip resistance
EN 13400, Footwear. Sampling location, preparation and duration of conditioning of samples and test pieces
EN/ISO 19952, Footwear — Vocabulary
EN/ISO 19953, Footwear — Test methods for heels — Resistance to lateral impact
EN/ISO 19956, Footwear — Test methods for heels — Fatigue resistance
EN/ISO 19957, Footwear — Test methods for heels — Heel pin holding strength
EN/ISO 19958, Footwear — Test methods for heels and top pieces — Top piece retention strength
3 Terms and definitions
For the purposes of this document, the terms and definitions in EN/ISO 19952 apply.
ISO/TR 20573:2006(E)
4 Requirements
4.1 General
This Technical Report establishes two different types of performance requirement.
The essential requirements shall all be taken into account. The additional ones can be additionally agreed
upon by the component supplier and the footwear manufacturer as indicated in 4.2 to 4.10.
The results of each single analytical determination, as well as the average values, shall be rounded off in
accordance with ISO 31-0.
When taken from finished footwear, samples shall be prepared in acc
...