SIST EN ISO 15098-3:2000
(Main)Dental tweezers - Part 3: College types (ISO 15098-3:2000)
Dental tweezers - Part 3: College types (ISO 15098-3:2000)
Zahnärtzliche Pinzetten - Teil 3: College Typ (ISO 15098-3:2000)
Dieser Teil von ISO 15098 legt Anforderungen einschließlich der Maße für zahnärztliche Pinzetten vom College-Typ fest.
Précelles dentaires - Partie 3: Type College (ISO 15098-3:2000)
Dental tweezers - Part 3: College types (ISO 15098-3:2000)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 15098-3:2000
01-november-2000
Dental tweezers - Part 3: College types (ISO 15098-3:2000)
Dental tweezers - Part 3: College types (ISO 15098-3:2000)
Zahnärtzliche Pinzetten - Teil 3: College Typ (ISO 15098-3:2000)
Précelles dentaires - Partie 3: Type College (ISO 15098-3:2000)
Ta slovenski standard je istoveten z: EN ISO 15098-3:2000
ICS:
11.060.20 =RERWHKQLþQDRSUHPD Dental equipment
SIST EN ISO 15098-3:2000 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 15098-3:2000
---------------------- Page: 2 ----------------------
SIST EN ISO 15098-3:2000
---------------------- Page: 3 ----------------------
SIST EN ISO 15098-3:2000
---------------------- Page: 4 ----------------------
SIST EN ISO 15098-3:2000
---------------------- Page: 5 ----------------------
SIST EN ISO 15098-3:2000
---------------------- Page: 6 ----------------------
SIST EN ISO 15098-3:2000
INTERNATIONAL ISO
STANDARD 15098-3
First edition
2000-02-15
Dental tweezers —
Part 3:
College types
Précelles dentaires —
Partie 3: Type College
Reference number
ISO 15098-3:2000(E)
©
ISO 2000
---------------------- Page: 7 ----------------------
SIST EN ISO 15098-3:2000
ISO 15098-3:2000(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not
be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this
file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this
area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters
were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event
that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2000
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic
or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body
in the country of the requester.
ISO copyright office
Case postale 56 � CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 734 10 79
E-mail copyright@iso.ch
Web www.iso.ch
Printed in Switzerland
ii © ISO 2000 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 15098-3:2000
ISO 15098-3:2000(E)
Contents Page
1 Scope .1
2 Normative references .1
3 Terms and definitions .1
4 Design and dimensions .1
5 Designation, labelling and marking .5
© ISO 2000 – All rights reserved iii
---------------------- Page: 9 ----------------------
SIST EN ISO 15098-3:2000
ISO 15098-3:2000(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO
member bodies). The work of preparing International Standards is normally carried out through ISO technical
committees. Each member body interested in a subject for which a technical committee has been established has
the right to be represented on that committee. International organizations, governmental and non-governmental, in
liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical
Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3.
Draft International Standards adopted by the technical committees are circulated to the member bodies for voting.
Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this part of ISO 15098 may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights.
Internat
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.