SIST EN 301 447 V1.1.1:2008
Satellite Earth Stations and Systems (SES) - Harmonized EN for satellite Earth Stations on board Vessels (ESVs) operating in the 4/6 GHz frequency bands allocated to the Fixed Satellite Service (FSS) covering essential requirements of article 3.2 of the R&TTE directive
Satellite Earth Stations and Systems (SES) - Harmonized EN for satellite Earth Stations on board Vessels (ESVs) operating in the 4/6 GHz frequency bands allocated to the Fixed Satellite Service (FSS) covering essential requirements of article 3.2 of the R&TTE directive
To provide norms for the operation of ESVs operating in the 4/6 GHz frequency bands.The present document applies to Earth Stations located on board Vessels (ESVs) which have the following characteristics:
• The ESV is comprised of all the equipment, electrical and mechanical, from the antenna itself to the interface with other communications equipment on board (usually referred to as the terrestrial interface).
• The ESV transmits in the frequency range from 5 925 MHz to 6 425 MHz allocated to the Fixed Satellite Services (FSS) (earth-to-space).
• The ESV receives in one or more frequencies within the range from 3,700 GHz to 4,200 GHz in the bands allocated to the Fixed Satellite Services (FSS) (space-to-earth), depending on the ITU Region where the ESV is located.
• The ESV transmits a single carrier.
• The ESV uses linear or circular polarization.
• The ESV operates through a geostationary satellite at least 2° to 3° away from any other geostationary satellite operating in the same frequency band and covering the same area.
NOTE 1: The satellite spacing is mainly equal to 3° in ITU Regions 1 and 3 and 2° in ITU Region 2.
The ESV transmits at elevations greater or equal to the minimum elevation angle declared by the applicant.
• The ESV antenna diameter is not smaller than 2,4 m.
• The ESV is designed for transmission and reception of radio-communications signals in accordance with any of the frequency bands specified above.
• The ESV is usually designed for unattended operation.
• The ESV is operating as part of a satellite network (e.g. star, mesh or point-to-point) used for the distribution and/or exchange of information between users.
• The ESV is controlled and monitored by a Network Control Facility (NCF). The NCF is outside the scope of the present document. The present document applies to the ESV with its ancillary equipment and its various telecommunication ports, and when operated within the boundary limits of the operational environmental profile declared by the applicant and when
installed as required by the applicant by declaration or in the user documentation.
The present document is intended to cover the provisions of Directive 1999/5/EC [1] (R&TTE Directive) Article 3.2, which states that "… radio equipment shall be so constructed that it effectively uses the spectrum allocated to terrestrial/space radio communications and orbital resources so as to avoid harmful interference". The present EN incorporates the technical limitations listed in annex 2 of ITU-R Resolution 902 (WRC-03), ECC Report (05)69, and ECC Report (06)91 (see bibliography). NOTE 2: According to Res. 902, any transmission from ESVs within the 300 km minimum distance of each country where the ESV transmit frequency band is used by the Fixed Service will be subject to the prior agreement of the concerned administration(s), which may specify additional operational requirements, or to the relevant ECC Decision. In addition to the present document, other ENs that specify technical requirements in respect of essential requirements under other parts of Article 3 of the Directive 1999/5/EC [1] (R&TTE Directive) may apply to equipment within the scope of the present document.
Satelitske zemeljske postaje in sistemi (SES) - Harmonizirani EN za satelitske zemeljske postaje na ladjah, delujoče v frekvenčnih pasovih 4/6 GHz, razporejenih za fiksne satelitske storitve (FSS), ki zajema bistvene zahteve člena 3.2 direktive R&TTE
General Information
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 301 447 V1.1.1:2008
01-marec-2008
6DWHOLWVNH]HPHOMVNHSRVWDMHLQVLVWHPL 6(6 +DUPRQL]LUDQL(1]DVDWHOLWVNH
]HPHOMVNHSRVWDMHQDODGMDKGHOXMRþHYIUHNYHQþQLKSDVRYLK*+]UD]SRUHMHQLK
]DILNVQHVDWHOLWVNHVWRULWYH )66 NL]DMHPDELVWYHQH]DKWHYHþOHQDGLUHNWLYH
5 77(
Satellite Earth Stations and Systems (SES) - Harmonized EN for satellite Earth Stations
on board Vessels (ESVs) operating in the 4/6 GHz frequency bands allocated to the
Fixed Satellite Service (FSS) covering essential requirements of article 3.2 of the R&TTE
directive
Ta slovenski standard je istoveten z: EN 301 447 Version 1.1.1
ICS:
33.060.30 Radiorelejni in fiksni satelitski Radio relay and fixed satellite
komunikacijski sistemi communications systems
SIST EN 301 447 V1.1.1:2008 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 301 447 V1.1.1:2008
---------------------- Page: 2 ----------------------
SIST EN 301 447 V1.1.1:2008
ETSI EN 301 447 V1.1.1 (2007-08)
Harmonized European Standard (Telecommunications series)
Satellite Earth Stations and Systems (SES);
Harmonized EN for satellite Earth Stations on board
Vessels (ESVs) operating in the 4/6 GHz frequency bands
allocated to the Fixed Satellite Service (FSS)
covering essential requirements of
article 3.2 of the R&TTE directive
---------------------- Page: 3 ----------------------
SIST EN 301 447 V1.1.1:2008
2 ETSI EN 301 447 V1.1.1 (2007-08)
Reference
DEN/SES-00271
Keywords
ESV, GSO, maritime, regulation, satellite
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
Individual copies of the present document can be downloaded from:
http://www.etsi.org
The present document may be made available in more than one electronic version or in print. In any case of existing or
perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF).
In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive
within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
http://portal.etsi.org/chaircor/ETSI_support.asp
Copyright Notification
No part may be reproduced except as authorized by written permission.
The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2007.
All rights reserved.
TM TM TM
DECT , PLUGTESTS and UMTS are Trade Marks of ETSI registered for the benefit of its Members.
TM
TIPHON and the TIPHON logo are Trade Marks currently being registered by ETSI for the benefit of its Members.
TM
3GPP is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners.
ETSI
---------------------- Page: 4 ----------------------
SIST EN 301 447 V1.1.1:2008
3 ETSI EN 301 447 V1.1.1 (2007-08)
Contents
Intellectual Property Rights.7
Foreword.7
Introduction .8
1 Scope.9
2 References.10
3 Definitions, symbols and abbreviations .10
3.1 Definitions.10
3.2 Symbols.12
3.3 Abbreviations.12
4 Technical requirements specifications .13
4.1 General.13
4.1.1 Environmental profile.13
4.1.2 Operational configurations.13
4.1.3 ESV states and radio states .14
4.2 Conformance requirements.15
4.2.1 On-axis emissions.15
4.2.1.1 Justification.15
4.2.1.2 Specification.15
4.2.1.3 Conformance tests.15
4.2.2 Antenna on-axis gain and off-axis gain pattern .15
4.2.2.1 Justification.15
4.2.2.2 Specification.16
4.2.2.3 Conformance tests.16
4.2.3 Off-axis spurious radiation .16
4.2.3.1 Justification.16
4.2.3.2 Specification.16
4.2.3.3 Conformance tests.17
4.2.4 On-axis spurious radiation for ESV.17
4.2.4.1 Justification.17
4.2.4.2 Specification.17
4.2.4.2.1 "Carrier-on" radio state.17
4.2.4.2.2 "Carrier-off" and "Emissions disabled" radio states.18
4.2.4.3 Conformance tests.18
4.2.5 Maximum ESV emissions towards the horizon.18
4.2.5.1 Justification.18
4.2.5.2 Specification.18
4.2.5.2.1 Specification 1: Maximum e.i.r.p. spectral density towards the horizon.18
4.2.5.2.2 Specification 2: Maximum e.i.r.p. towards the horizon.18
4.2.5.3 Conformance tests.19
4.2.6 Off-axis e.i.r.p. emission density within the band.19
4.2.6.1 Justification.19
4.2.6.2 Specification.19
4.2.6.3 Conformance tests.20
4.2.7 Carrier suppression.21
4.2.7.1 Justification.21
4.2.7.2 Specification.21
4.2.7.3 Conformance tests.21
4.2.8 Antenna Pointing and Polarization Alignment for ESVs.21
4.2.8.1 Justification.21
4.2.8.2 Specification.21
4.2.8.3 Conformance tests.22
4.2.9 Cessation of emissions of the ESV .22
4.2.9.1 Justification.22
ETSI
---------------------- Page: 5 ----------------------
SIST EN 301 447 V1.1.1:2008
4 ETSI EN 301 447 V1.1.1 (2007-08)
4.2.9.2 Specification.22
4.2.9.2.1 Specification 1: Mode of cessation of emissions.22
4.2.9.2.2 Specification 2: Conditions under which the ESV must cease emissions .23
4.2.9.2.3 Specification 3: Cessation of emissions .23
4.2.9.2.4 Specification 4: Fault conditions .24
4.2.9.3 Conformance tests.24
4.2.10 Identification of ESV .24
4.2.10.1 Justification.24
4.2.10.2 Specification.24
4.2.10.3 Conformance tests.24
4.2.11 Control and Monitoring Functions (CMFs) .24
4.2.11.1 CMF State Diagram .24
4.2.11.2 Processor monitoring.25
4.2.11.2.1 Justification.25
4.2.11.2.2 Specification.25
4.2.11.2.3 Conformance tests.26
4.2.11.3 Transmit subsystem monitoring.26
4.2.11.3.1 Justification.26
4.2.11.3.2 Specification.26
4.2.11.3.3 Conformance tests.26
4.2.11.4 Power-on/Reset.26
4.2.11.4.1 Justification.26
4.2.11.4.2 Specification.26
4.2.11.4.3 Conformance tests.26
4.2.11.5 Control Channel (CC) and Response Channel (RC) .26
4.2.11.5.1 Justification.26
4.2.11.5.2 Specification.27
4.2.11.5.3 Conformance tests.27
4.2.11.6 Network control commands .27
4.2.11.6.1 Justification.27
4.2.11.6.2 Specification.28
4.2.11.6.3 Conformance test.28
4.2.11.7 Initial burst transmission .28
4.2.11.7.1 Justification.28
4.2.11.7.2 Specification.28
4.2.11.7.3 Conformance tests.28
5 Testing for compliance with technical requirements.29
5.1 Environmental conditions for testing .29
5.2 Essential radio test suites.29
6 Test methods for the complete ESV.29
6.1 General.29
6.2 On-axis emissions.30
6.2.1 Test method.30
6.2.1.1 Test site.30
6.2.1.2 Method of measurement.30
6.2.1.2.1 General.30
6.2.1.2.2 Method of measurement at the antenna flange .30
6.2.1.2.3 Method of measurement with a test antenna .31
6.3 Antenna on-axis gain and off-axis gain pattern.31
6.3.1 Method of measurement.31
6.4 Off-axis spurious radiation.31
6.4.1 Test method.31
6.4.1.1 Up to 2 000 MHz .32
6.4.1.1.1 Test site.32
6.4.1.1.2 Procedure.33
6.4.1.2 Above 2 000 MHz.33
6.4.1.2.1 Identification of the significant frequencies of spurious radiation .33
6.4.1.2.2 Measurement of radiated power levels of identified spurious radiation.34
6.4.1.2.3 Measurement of conducted spurious radiation at the antenna flange .35
6.5 On-axis spurious radiation.36
ETSI
---------------------- Page: 6 ----------------------
SIST EN 301 447 V1.1.1:2008
5 ETSI EN 301 447 V1.1.1 (2007-08)
6.5.1 Test method.36
6.5.1.1 Test site.36
6.5.1.2 Method of measurement.36
6.5.1.2.1 General.36
6.5.1.2.2 Method of measurement at the antenna flange .36
6.5.1.2.3 Method of measurement with a test antenna .37
6.6 Maximum ESV emissions towards the horizon.38
6.6.1 Maximum e.i.r.p. towards the horizon.38
6.6.2 Maximum e.i.r.p. spectral density towards the horizon .38
6.7 Off-axis e.i.r.p. emission density within the band .39
6.7.1 Test method.39
6.7.1.1 General.39
6.7.1.2 Transmit output power density.39
6.7.1.2.1 General.39
6.7.1.2.2 Test site.39
6.7.1.2.3 Method of measurement.40
6.7.1.3 Antenna transmit gain.41
6.7.1.3.1 General.41
6.7.1.3.2 Test site.41
6.7.1.3.3 Method of measurement.41
6.7.1.4 Antenna transmit radiation patterns .42
6.7.1.4.1 General.42
6.7.1.4.2 Test site.42
6.7.1.4.3 Test arrangement.43
6.7.1.4.4 Co-polar radiation pattern-azimuth.43
6.7.1.4.5 Co-polar radiation pattern-elevation.43
6.7.1.4.6 Cross-polar radiation pattern-azimuth .44
6.7.1.4.7 Cross-polar radiation pattern-elevation .45
6.7.2 Computation of results.46
6.8 Carrier suppression.46
6.8.1 Test method.46
6.9 Antenna pointing for ESV.46
6.9.1 General.46
6.9.2 Test method.47
6.10 Antenna mechanical stability .48
6.10.1 Test method .48
6.11 Polarization angle alignment capability .48
6.11.1 Test method .48
6.12 Cessation of emissions of the ESV.48
6.12.1 Test arrangement.48
6.12.2 Test method .49
6.12.2.1 Required documentation.49
6.12.2.2 Cessation of emissions from the "Transmission enabled" state .49
6.12.2.3 Cessation of emission from the "Transmission disabled" state.50
6.12.2.4 Cessation of emission from the "Initial Phase" state.50
6.12.2.4.1 EUTs transmitting initial bursts.50
6.12.2.4.2 EUTs not transmitting initial bursts.50
6.12.2.5 "Single action" means of cessation of emissions.51
6.12.2.6 Fault conditions.51
6.13 Identification of ESV.52
6.13.1 Test arrangement.52
6.13.2 Test method .52
6.14 Control and Monitoring Functions .52
6.14.1 Test arrangement.52
6.14.2 Processor monitoring - Test method .
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.