oSIST prEN ISO 21180:2025

Light conveyor belts - Determination of the maximum tensile strength (ISO/DIS 21180:2024)

Leichte Fördergurte - Bestimmung der maximalen Zugfestigkeit (ISO/DIS 21180:2024)

Courroies transporteuses légères - Détermination de la résistance maximale à la traction (ISO/DIS 21180:2024)

L'ISO 21180:2013 spécifie une méthode d'essai permettant de déterminer la résistance maximale à la rupture des courroies transporteuses légères selon l''ISO 21183-1, ou d'autres courroies transporteuses lorsque l''ISO 283 n'est pas applicable.

Naprave za kontinuirni transport - Lahki trakovi tračnih transporterjev - Ugotavljanje največje natezne trdnost i(ISO/DIS 21180:2024)

General Information

• Status: Not Published
• Public Enquiry End Date: 27-Feb-2025
• ICS: 53.040.20 - Components for conveyors
• Technical Committee: DTN - Lift and transport appliances
• Current Stage: 4020 - Public enquire (PE) (Adopted Project)
• Start Date: 30-Dec-2024
• Due Date: 19-May-2025
• Ref Project: prEN ISO 21180 - Light conveyor belts - Determination of the maximum tensile strength (ISO/DIS 21180:2024)

Relations

• Revises: SIST EN ISO 21180:2013 - Light conveyor belts - Determination of the maximum tensile strength (ISO 21180:2013)
• Effective Date: 22-Nov-2023

Standards Content (Sample)

SLOVENSKI STANDARD
01-februar-2025
Naprave za kontinuirni transport - Lahki trakovi tračnih transporterjev -
Ugotavljanje največje natezne trdnost i(ISO/DIS 21180:2024)
Light conveyor belts - Determination of the maximum tensile strength (ISO/DIS
21180:2024)
Leichte Fördergurte - Bestimmung der maximalen Zugfestigkeit (ISO/DIS 21180:2024)
Courroies transporteuses légères - Détermination de la résistance maximale à la traction
(ISO/DIS 21180:2024)
Ta slovenski standard je istoveten z: prEN ISO 21180
ICS:
53.040.10 Transporterji Conveyors
53.040.20 Deli za transporterje Components for conveyors
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

DRAFT
International
Standard
ISO/DIS 21180
ISO/TC 41/SC 3
Light conveyor belts —
Secretariat: SAC
Determination of the maximum
Voting begins on:
tensile strength
2024-12-17
Courroies transporteuses légères — Détermination de la
Voting terminates on:
résistance maximale à la traction
2025-03-11
ICS: 53.040.20
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENTS AND APPROVAL. IT
IS THEREFORE SUBJECT TO CHANGE
AND MAY NOT BE REFERRED TO AS AN
INTERNATIONAL STANDARD UNTIL
PUBLISHED AS SUCH.
This document is circulated as received from the committee secretariat.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
ISO/CEN PARALLEL PROCESSING
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
NATIONAL REGULATIONS.
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
PROVIDE SUPPORTING DOCUMENTATION.
Reference number
ISO/DIS 21180:2024(en)
DRAFT
ISO/DIS 21180:2024(en)
International
Standard
ISO/DIS 21180
ISO/TC 41/SC 3
Light conveyor belts —
Secretariat: SAC
Determination of the maximum
Voting begins on:
tensile strength
Courroies transporteuses légères — Détermination de la
Voting terminates on:
résistance maximale à la traction
ICS: 53.040.20
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENTS AND APPROVAL. IT
IS THEREFORE SUBJECT TO CHANGE
AND MAY NOT BE REFERRED TO AS AN
INTERNATIONAL STANDARD UNTIL
PUBLISHED AS SUCH.
This document is circulated as received from the committee secretariat.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL,
© ISO 2024
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
STANDARDS MAY ON OCCASION HAVE TO
ISO/CEN PARALLEL PROCESSING
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
BE CONSIDERED IN THE LIGHT OF THEIR
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
or ISO’s member body in the country of the requester.
NATIONAL REGULATIONS.
ISO copyright office
RECIPIENTS OF THIS DRAFT ARE INVITED
CP 401 • Ch. de Blandonnet 8
TO SUBMIT, WITH THEIR COMMENTS,
CH-1214 Vernier, Geneva
NOTIFICATION OF ANY RELEVANT PATENT
Phone: [phone]
RIGHTS OF WHICH THEY ARE AWARE AND TO
PROVIDE SUPPORTING DOCUMENTATION.
Email: [e-mail]
Website: www.iso.org
Published in Switzerland Reference number
ISO/DIS 21180:2024(en)
ii
ISO/DIS 21180:2024(en)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Symbols . 1
5 Principle . 2
6 Apparatus . 2
7 Test pieces . 3
7.1 Shape and dimensions .3
7.2 Number and selection .3
7.3 Conditioning.4
7.4 Preparation .4
8 Test method . 4
8.1 Test room condition .4
8.2 Procedure .4
9 Calculation and expression of results . 5
10 Test report . 5
Bibliography . 6

iii
ISO/DIS 21180:2024(en)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out through
ISO technical committees. Each member body interested in a subject for which a technical committee
has been established has the right to be represented on that committee. International organizations,
governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely
with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are described
in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the different types
of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the
ISO/IEC Directives, Part 2 (see www.iso.org/directives).
ISO draws attention to the possibility that the implementation of this document may involve the use of (a)
patent(s). ISO takes no position concerning the evidence, validity or applicability of any claimed patent
rights in respect thereof. As of the date of publication of this document, ISO had received notice of (a)
patent(s) which may be required to implement this document. However, implementers are cautioned that
this may not represent the latest information, which may be obtained from the patent database available at
www.iso.org/patents. ISO shall not be held responsible for identifying any or all such patent rights.
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntar
...