SIST EN ISO 25178-601:2010
(Main)Geometrical product specifications (GPS) - Surface texture: Areal - Part 601: Nominal characteristics of contact (stylus) instruments (ISO 25178-601:2010)
Geometrical product specifications (GPS) - Surface texture: Areal - Part 601: Nominal characteristics of contact (stylus) instruments (ISO 25178-601:2010)
This part of ISO 25178 defines the metrological characteristics of contact (stylus) areal surface texture measuring instruments.
Geometrische Produktspezifikation (GPS) - Oberflächenbeschaffenheit: Flächenhaft - Teil 601: Merkmale von berührend messenden Geräten (mit Taster) (ISO 25178-601:2010)
Dieses Dokument legt die metrologischen Merkmale von Tastschnittgeräten zur flächenhaften Messung der
Oberflächentopographie fest.
Spécification géométrique des produits (GPS) - État de surface: surfacique - Partie 601: Caractéristiques nominales des instruments de mesure par contact (instruments à stylet) (ISO 25178-601:2010)
L'ISO 25178-601:2010 spécifie les caractéristiques métrologiques des instruments de mesure de l'état de surface surfacique par contact (instruments à palpeur).
Specifikacija geometrijskih veličin izdelka - Tekstura površine: ploskovna - 601. del: Imenske značilnosti kontaktnih (s tipalom) instrumentov (ISO 25178-601:2010)
Ta del ISO 25178 opredeljuje metrološke značilnosti kontaktnih (s tipalom) merilnih instrumentov ploskovne teksture površine.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-oktober-2010
6SHFLILNDFLMDJHRPHWULMVNLKYHOLþLQL]GHOND7HNVWXUDSRYUãLQH SORVNRYQD
GHO ,PHQVNH]QDþLOQRVWLNRQWDNWQLK VWLSDORP LQVWUXPHQWRY ,62
Geometrical product specifications (GPS) - Surface texture: Areal - Part 601: Nominal
characteristics of contact (stylus) instruments (ISO 25178-601:2010)
Geometrische Produktspezifikation (GPS) - Oberflächenbeschaffenheit: Flächenhaft -
Teil 601: Merkmale von berührend messenden Geräten (mit Taster) (ISO 25178-
601:2010)
Spécification géométrique des produits (GPS) - État de surface: surfacique - Partie 601:
Caractéristiques nominales des instruments de mesure par contact (instruments à stylet)
(ISO 25178-601:2010)
Ta slovenski standard je istoveten z: EN ISO 25178-601:2010
ICS:
17.040.20 Lastnosti površin Properties of surfaces
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
EN ISO 25178-601
NORME EUROPÉENNE
EUROPÄISCHE NORM
July 2010
ICS 17.040.20
English Version
Geometrical product specifications (GPS) - Surface texture:
Areal - Part 601: Nominal characteristics of contact (stylus)
instruments (ISO 25178-601:2010)
Spécification géométrique des produits (GPS) - État de Geometrische Produktspezifikation (GPS) -
surface: Surfacique - Partie 601: Caractéristiques Oberflächenbeschaffenheit: Flächenhaft - Teil 601:
nominales des instruments à contact (à palpeur) (ISO Merkmale von berührend messenden Geräten (mit Taster)
25178-601:2010) (ISO 25178-601:2010)
This European Standard was approved by CEN on 6 May 2010.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the
official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2010 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 25178-601:2010: E
worldwide for CEN national Members.
Contents Page
Foreword .3
Foreword
This document (EN ISO 25178-601:2010) has been prepared by Technical Committee ISO/TC 213
"Dimensional and geometrical product specifications and verification" in collaboration with Technical
Committee CEN/TC 290 “Dimensional and geometrical product specification and verification” the secretariat of
which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by January 2011, and conflicting national standards shall be withdrawn at
the latest by January 2011.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of ISO 25178-601:2010 has been approved by CEN as a EN ISO 25178-601:2010 without any
modification.
INTERNATIONAL ISO
STANDARD 25178-601
First edition
2010-07-01
Geometrical product specifications
(GPS) — Surface texture: Areal —
Part 601:
Nominal characteristics of contact
(stylus) instruments
Spécification géométrique des produits (GPS) — État de surface:
Surfacique —
Partie 601: Caractéristiques nominales des instruments à contact (à
palpeur)
Reference number
ISO 25178-601:2010(E)
©
ISO 2010
ISO 25178-601:2010(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2010
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2010 – All rights reserved
ISO 25178-601:2010(E)
Contents Page
Foreword .iv
Introduction.v
1 Scope.1
2 Normative references.1
3 Terms and definitions .1
4 Summary of metrological characteristics.9
Annex A (normative) Classification of the different configurations for areal surface texture
scanning instruments .11
Annex B (informative) Features of an areal surface texture measuring instrument.12
Annex C (informative) Relationship to the GPS matrix model .15
Bibliography.17
ISO 25178-601:2010(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 25178-601 was prepared by Technical Committee ISO/TC 213, Dimensional and geometrical product
specifications and verification.
ISO 25178 consists of the following parts, under the general title Geometrical product specifications (GPS) —
Surface texture: Areal:
⎯ Part 2: Terms, definitions and surface texture parameters
⎯ Part 3: Specification operators
⎯ Part 6: Classification of methods for measuring surface texture
⎯ Part 7: Software measurement standards
⎯ Part 601: Nominal characteristics of contact (stylus) instruments
⎯ Part 602: Nominal characteristics of non-contact (confocal chromatic probe) instruments
⎯ Part 603: Nominal characteristics of non-contact (phase-shifting interferometric microscopy) instruments
⎯ Part 701: Calibration and measurement standards for contact (stylus) instruments
The following parts are under preparation:
⎯ Part 604: Nominal characteristics of non-contact (coherence scanning interferometry) instruments
⎯ Part 605: Nominal characteristics of non-contact (point autofocusing) instruments
iv © ISO 2010 – All rights reserved
ISO 25178-601:2010(E)
Introduction
This part of ISO 25178 is a geometrical product specification standard and is to be regarded as a general
GPS standard (see ISO/TR 14638). It influences chain link 5 of the chain of standards on roughness profile,
waviness profile, primary profile and areal surface texture.
For more detailed information of the relation of this standard to the GPS matrix model, see Annex C.
INTERNATIONAL STANDARD ISO 25178-601:2010(E)
Geometrical product specifications (GPS) — Surface texture:
Areal —
Part 601:
Nominal characteristics of contact (stylus) instruments
1 Scope
This part of ISO 25178 defines the metrological characteristics of contact (stylus) areal surface texture
measuring instruments.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the cited editions apply. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 3274:1996, Geometrical Product Specifications (GPS) — Surface texture: Profile method — Nominal
characteristics of contact (stylus) instruments
ISO 4287, Geometrical Product Specifications (GPS) — Surface texture: Profile method — Terms, definitions
and surface texture parameters
ISO 10360-1, Geometrical Product Specifications (GPS) — Acceptance and reverification tests for coordinate
measuring machines (CMM) — Part 1: Vocabulary
ISO/IEC Guide 99:2007, International vocabulary of metrology — Basic and general concepts and associated
terms (VIM)
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 3274, ISO 4287, ISO 10360-1 and
ISO/IEC Guide 99 and the following apply.
3.1 General terms and definitions
3.1.1
coordinate system of the instrument
right hand orthonormal system of axes (X,Y,Z) defined as:
⎯ (X,Y) is the plane established by the areal reference guide of the instrument;
⎯ Z-axis is in the plane of the stylus trajectory and is perpendicular to the (X,Y) plane (see Figure 1)
NOTE Normally, the X-axis is the tracing direction and the Y-axis is the stepping axis.
ISO 25178-601:2010(E)
3.1.2
measurement loop
closed chain which comprises all components connecting workpiece and the stylus tip, e.g. the means of
positioning, the workholding fixture, the measuring stand, the drive unit, the probing system (pick-up)
See Figure 1.
NOTE The measurement loop will be subjected to external and internal disturbances which influence the
measurement uncertainty.
Key
1 coordinate system of the instrument
2 measurement loop
Figure 1 — Coordinate system and measurement loop of the instrument
3.1.3
user adjustment
〈of a measuring instrument〉 adjustment employing only the means available to the user
NOTE This is an operation normally carried out by the user. It involves the use of a material measure, usually
supplied with the instrument. The result of this operation automatically or manually adjusts certain parameters in order that
the instrument operates correctly.
3.1.4
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.