iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
SIST

SIST EN 61290-1-3:1999

(Main)

Optical fibre amplifiers - Basic specification - Part 1-3: Test methods for gain parameters - Optical power meter (IEC 61290-1-3:1998)

Optical fibre amplifiers - Basic specification - Part 1-3: Test methods for gain parameters - Optical power meter (IEC 61290-1-3:1998)

Applies to optical fibre amplifiers using active fibres, containing rare-earth dopants, presently commercially available. Establishes uniform requirements for accurate and reliable measurements, by means of the optical power meter test method, of the following OFA parameters: - small-signal gain; - reverse small-signal gain; - maximum small-signal gain; - maximum small-signal gain wavelength; - maximum small-signal gain variation with temperature; - small-signal gain wavelength band; - small-signal gain wavelength variation; - small signal gain stability; - polarization-dependent gain variation.

Lichtwellenleiter-Verstärker - Grundspezifikation -- Teil 1-3: Prüfverfahren für Verstärkungsparameter - Optischer Leistungsmesser

Amplificateurs à fibres optiques - Spécification de base -- Partie 1-3: Méthodes d'essai pour les paramètres de gain - Mesureur de puissance optique

S'applique aux amplificateurs à fibres optiques (AFO) utilisant des fibres actives contenant des dopants de terre rare, actuellement commercialisés. Etablit des spécifications uniformes pour des mesures précises et fiables, par le biais de la méthode d'essai mesureur de puissance optique, des paramètres d'AFO donnés ci-dessous: - gain faible signal; - gain faible signal inverse; - gain faible signal maximal; - longueur d'onde du gain faible signal maximal; - variation maximale du gain faible signal en fonction de la longueur de la température; - bande de longueur d'onde du gain faible signal; - variation du gain faible signal en fonction de la longueur d'onde; - stabilité du gain faible signal; - variation du gain en fonction de la polarisation.

Optical fibre amplifiers - Basic specification - Part 1-3: Test methods for gain parameters - Optical power meter (IEC 61290-1-3:1998)

General Information

Status
Withdrawn
Publication Date
30-Apr-1999
Withdrawal Date
28-Feb-2006
ICS
33.180.30 - Optic amplifiers
Technical Committee
MOC - Mobile Communications
Current Stage
9900 - Withdrawal (Adopted Project)
Start Date
01-Mar-2006
Due Date
01-Mar-2006
Completion Date
01-Mar-2006
Ref Project
EN 61290-1-3:1998 - Optical fibre amplifiers - Basic specification - Part 1-3: Test methods for gain parameters - Optical power meter

Relations

Replaced By
SIST EN 61290-1-3:2006 - Optical amplifiers - Test methods -- Part 1-3: Power and gain parameters - Optical power meter method
Effective Date
29-Jan-2023
Replaced By
SIST EN 61290-1-3:2006 - Optical amplifiers - Test methods -- Part 1-3: Power and gain parameters - Optical power meter method
Effective Date
07-Jun-2022

Buy Standard

EN 61290-1-3:1999EN 61290-1-3:1999
PreviousNext
Standard
EN 61290-1-3:1999
English language
17 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 61290-1-3:1999
01-maj-1999
Optical fibre amplifiers - Basic specification - Part 1-3: Test methods for gain
parameters - Optical power meter (IEC 61290-1-3:1998)
Optical fibre amplifiers - Basic specification - Part 1-3: Test methods for gain parameters
- Optical power meter (IEC 61290-1-3:1998)
Lichtwellenleiter-Verstärker - Grundspezifikation -- Teil 1-3: Prüfverfahren für
Verstärkungsparameter - Optischer Leistungsmesser
Amplificateurs à fibres optiques - Spécification de base -- Partie 1-3: Méthodes d'essai
pour les paramètres de gain - Mesureur de puissance optique
Ta slovenski standard je istoveten z: EN 61290-1-3:1998
ICS:
33.180.30 2SWLþQLRMDþHYDOQLNL Optic amplifiers
SIST EN 61290-1-3:1999 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 61290-1-3:1999

---------------------- Page: 2 ----------------------

SIST EN 61290-1-3:1999

---------------------- Page: 3 ----------------------

SIST EN 61290-1-3:1999

---------------------- Page: 4 ----------------------

SIST EN 61290-1-3:1999

---------------------- Page: 5 ----------------------

SIST
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

SIST
SIST EN IEC 61291-2:2023(Main)
Optical amplifiers - Part 2: Single channel applications - Performance specification template (IEC 61291-2:2023)
EN IEC 61291-2:2023

IEC 61291-2:2023 is available as IEC 61291-2:2023 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.

IEC 61292-2:2023 provides a performance specification template applicable to optical amplifiers (OAs) used in single channel applications. Multichannel applications are covered in IEC 61291-4. The objective of this template is to provide a framework for the preparation of performance standards and/or product specifications defining the performance of OA devices used in single channel applications. In addition to the requirements specified in this template, a performance standard or product specification could include other parameters, such as ratings, operating conditions, tests, and pass/fail criteria. For a particular application, product specification writers could add specification parameters and/or groups of specification parameters to this template, without removing the parameters specified in this document. This fifth edition cancels and replaces the fourth edition published in 2016. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition:
- the test methods for gain ripple in Table 2, Table 4 and Table 6 refer now to the IEC 61290‑1 series;
- the SOA definition (3.1.3) refers now to IEC 61931.

  • Standard
    23 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    20 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN IEC 61290-1:2022(Main)
Optical amplifiers - Test methods - Part 1: Power and gain parameters (IEC 61290-1:2022)
EN IEC 61290-1:2022

This part of IEC 61290 applies to all commercially available optical amplifiers (OAs) and
optically amplified subsystems. It applies to OAs using optically pumped fibres (optical fibre
amplifiers (OFAs) based on either rare-earth doped fibres or on the Raman effect),
semiconductors (semiconductor optical amplifiers (SOAs)), and waveguides (planar optical
waveguide amplifiers (POWAs)). It is specifically directed to single-channel amplifiers. Test
methods for multichannel amplifiers are defined in the IEC 61290-10 series.
This document establishes uniform requirements for accurate and reliable measurements of the
following OA parameters, as defined in IEC 61291-1:2018, Clause 3:
a) nominal output signal power;
b) gain;
c) reverse gain;
d) maximum gain;
e) maximum gain wavelength;
f) maximum gain variation with temperature;
g) gain wavelength band;
h) gain wavelength variation;
i) gain stability;
j) polarization-dependent gain;
k) gain ripple (SOA only);
l) large-signal output stability;
m) saturation output power;
n) maximum output signal power;
o) maximum total output power.
NOTE 1 The applicability of the test methods described in this document to distributed Raman amplifiers is still
under study.
NOTE 2 All numerical values followed by (‡) are suggested values for which the measurement is assured. Other
values are acceptable if verified.

  • Standard
    17 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    15 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN IEC 61290-1-3:2021(Main)
Optical amplifiers - Test methods - Part 1-3: Power and gain parameters - Optical power meter method (IEC 61290-1-3:2021)
EN IEC 61290-1-3:2021

This part of IEC 61290 applies to all commercially available optical amplifiers (OA) and optically
amplified subsystems. It applies to OA using optically pumped fibres (OFA based on either rareearth
doped fibres or on the Raman effect), semiconductors (SOA), and waveguides (POWA).
NOTE 1 The applicability of the test methods described in this document to distributed Raman amplifiers is for
further study.
The object of this document is to establish uniform requirements for accurate and reliable
measurements, by means of the optical power meter test method, of the following OA
parameters, as defined in IEC 61291-1:
a) nominal output signal power;
b) gain;
c) polarization-dependent gain;
d) maximum output signal power;
e) maximum total output power.
NOTE 2 All numerical values followed by (‡) are suggested values for which the measurement is assured. Other
values can be acceptable upon verification.
This document applies to single-channel amplifiers. For multichannel amplifiers,
IEC 61290-10 (all parts) applies.

  • Standard
    19 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN IEC 61290-1-1:2021(Main)
Optical amplifiers - Test methods - Part 1-1: Power and gain parameters - Optical spectrum analyzer method (IEC 61290-1-1:2020)
EN IEC 61290-1-1:2020

This part of IEC 61290 applies to all commercially available optical amplifiers (OAs) and
optically amplified modules. It applies to OAs using optical fibre amplifiers (OFAs) based on
either rare-earth doped fibres or on the Raman effect, semiconductor OAs (SOAs) and planar
optical waveguide amplifiers (POWAs).
The object of this document is to establish uniform requirements for accurate and reliable
measurements, by means of the optical spectrum analyzer (OSA) test method, of the following
OA parameters, as defined in IEC 61291-1:
a) nominal output signal power;
b) gain;
c) polarization-dependent gain (PDG);
d) maximum output signal power;
e) maximum total output power.
In addition, this document provides the test method of:
f) gain ripple (for SOAs).
NOTE All numerical values followed by (‡) are suggested values for which the measurement is assured.
The object of this document is specifically directed to single-channel amplifiers. Test methods
for multichannel amplifiers are standardized in IEC 61290-10 (all parts) [1]1.

  • Standard
    22 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN IEC 62343-3-3:2020(Main)
Dynamic modules - Part 3-3: Performance specification templates - Wavelength selective switches (IEC 62343-3-3:2020)
EN IEC 62343-3-3:2020

This part of IEC 62343 provides a performance specification template for wavelength selective
switches. The object is to provide a framework for the preparation of detail specifications on the
performance of wavelength selective switches.
Additional specification parameters are often included for detailed product specifications or
performance specifications if necessary. However, specification parameters specified in this
document are not removed from the detail product specifications or performance specifications.
The technical information regarding wavelength selective switches and their applications in
DWDM systems with single-mode fibres are described in IEC TR 62343-6-4.

  • Standard
    17 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 61291-5-2:2017/AC:2019(Corrigendum)
Optical amplifiers - Part 5-2: Qualification specifications - Reliability qualification for optical fibre amplifiers (IEC 61291-5-2:2017/COR1:2019)
EN 61291-5-2:2017/AC:2019-06
  • Corrigendum
    3 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Corrigendum
    3 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN IEC 61290-4-4:2018(Main)
Optical amplifiers - Test methods - Part 4-4: Gain transient parameters - Single channel optical amplifiers with gain control (IEC 61290-4-4:2018)
EN IEC 61290-4-4:2018

This part of IEC 61290-4 applies to optical amplifiers (OAs) and optically amplified elementary
sub-systems. More specifically, it applies to OAs using active fibres (optical fibre amplifiers,
OFAs) containing rare-earth dopants, such as erbium doped fibre amplifiers (EDFAs),
presently commercially available, as indicated in IEC 61291-1.
This document provides the general background for optical amplifier gain transients and their
measurements and indicates those IEC standard test methods for accurate and reliable
measurements of the following transient parameters:
a) optical input power increase/decrease transient gain overshoot and transient net gain
overshoot;
b) optical input power increase/decrease transient gain undershoot and transient net gain
undershoot;
c) optical input power increase/decrease gain offset;
d) optical input power increase/decrease transient gain response constant (settling time).
These parameters have been included to provide a complete description of the transient
behaviour of gain controlled OA. The parameters defined here are applicable if the amplifier is
an OFA or an alternative type of OA.

  • Standard
    16 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN IEC 61290-4-3:2018(Main)
Optical amplifiers - Test methods - Part 4-3: Power transient parameters - Single channel optical amplifiers in output power control (IEC 61290-4-3:2018)
EN IEC 61290-4-3:2018

This part of IEC 61290 applies to output power controlled optically amplified, elementary
sub-systems. It applies to optical fibre amplifiers (OFAs) using active fibres containing
rare-earth dopants, presently commercially available, as indicated in IEC 61291-1, as well as
alternative optical amplifiers that can be used for single channel output power controlled
operation, such as semiconductor optical amplifiers (SOAs).
The object of this document is to provide the general background for optical amplifiers (OAs)
power transients and their measurements and to indicate those IEC standard test methods for
accurate and reliable measurements of the following transient parameters:
a) transient power response;
b) transient power overcompensation response;
c) steady-state power offset;
d) transient power response time.
The stimulus and responses behaviours under consideration include the following:
1) channel power increase (step transient);
2) channel power reduction (inverse step transient);
3) channel power increase/reduction (pulse transient);
4) channel power reduction/increase (inverse pulse transient);
5) channel power increase/reduction/increase (lightning bolt transient);
6) channel power reduction/increase/reduction (inverse lightning bolt transient).
These parameters have been included to provide a complete description of the transient
behaviour of an output power transient controlled OA. The test definitions defined here are
applicable if the amplifier is an OFA or an alternative OA. However, the description in
Annex A concentrates on the physical performance of an OFA and provides a detailed
description of the behaviour of an OFA; it does not give a similar description of other OA
types. Annex B provides a detailed description background of the dynamic phenomenon in
output power controlled amplifiers under transient conditions and Annex C details the impact
of speed of transient inputs.

  • Standard
    27 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    25 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN IEC 61291-1:2018(Main)
Optical amplifiers - Part 1: Generic specification (IEC 61291-1:2018)
EN IEC 61291-1:2018

This part of IEC 61291 applies to all commercially available optical amplifiers (OAs) and
optically amplified assemblies. It applies to OAs using optically pumped fibres (OFAs based
either on rare-earth doped fibres or on the Raman effect), semiconductors (SOAs), and
waveguides (POWAs).
The object of this document is
– to establish uniform requirements for transmission, operation, reliability and environmental
properties of OAs, and
– to provide assistance to the purchaser in the selection of consistently high-quality OA
products for his particular applications.
Parameters specified for OAs are those characterizing the transmission, operation, reliability
and environmental properties of the OA seen as a "black box" from a general point of view. In
the sectional and detail specifications a subset of these parameters will be specified
according to the type and application of the particular OA device or assembly.

  • Standard
    33 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 61291-5-2:2017(Main)
Optical amplifiers - Part 5-2: Qualification specifications - Reliability qualification for optical fibre amplifiers (IEC 61291-5-2:2017)
EN 61291-5-2:2017

This part of IEC 61291 applies to optical amplifiers (OAs) and optically amplified, elementary
sub-systems for terrestrial applications, using active fibres (optical fibre amplifiers (OFAs))
containing rare-earth dopants, which are commercially available.
The black box approach is used in this document. The black box approach is adopted in order
to give product specifications which are independent of OA implementation details. For
reliability qualification purposes, some information about the internal components is needed;
these internal parts are themselves treated as black boxes. This document gives
requirements for the evaluation of OA reliability by combining the reliability of such internal
black boxes.
The object of this document is to specify the minimum list of reliability qualification tests,
requirements on failure criteria during testing and on reliability predictions, and give the
relevant normative references to establish a standard method for the assessment of the
reliability of OFA devices and sub-systems in order to minimize risks and to promote product
development and reliability qualification.

  • Standard
    20 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    20 pages
    English language
    sale 10% off
    e-Library read for
    1 day