iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
SIST

SIST EN 140401:2002

(Main)

Blank Detail Specification: Fixed low power non-wire wound surface mounting (SMD) resistors

Blank Detail Specification: Fixed low power non-wire wound surface mounting (SMD) resistors

Supersedes CECC 40 401:1989 * Superseded by EN 140401:2002

Vordruck für Bauartspezifikation: Oberflächenmontierbare nichtdrahtgewickelte Festwiderstände (SMD) niedriger Belastbarkeit

Specification particulière cadre: Résistances fixes non bobinées à faible dissipation pour montage en surface (CMS)

Blank detail specification: Fixed low power non-wire wound surface mounting (SMD) resistors

General Information

Status
Withdrawn
Publication Date
31-Aug-2002
Withdrawal Date
20-Oct-2009
ICS
31.040.10 - Fixed resistors
Technical Committee
I11 - Imaginarni 11
Current Stage
9900 - Withdrawal (Adopted Project)
Start Date
19-Oct-2009
Due Date
11-Nov-2009
Completion Date
21-Oct-2009
Ref Project
EN 140401:1996 - Blank Detail Specification: Fixed low power non-wire wound surface mounting (SMD) resistors

Relations

Replaced By
SIST EN 140401:2003 - Blank Detail Specification: Fixed low power non wire-wound surface mount (SMD) resistors
Effective Date
29-Jan-2023
Replaced By
SIST EN 140401:2003 - Blank Detail Specification: Fixed low power non wire-wound surface mount (SMD) resistors
Effective Date
07-Jun-2022

Buy Standard

EN 140401:2002EN 140401:2002
PreviousNext
Standard
EN 140401:2002
English language
16 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Blank detail specification: Fixed low power non-wire wound surface mounting (SMD) resistorsVordruck für Bauartspezifikation: Oberflächenmontierbare nichtdrahtgewickelte Festwiderstände (SMD) niedriger BelastbarkeitSpecification particulière cadre: Résistances fixes non bobinées à faible dissipation pour montage en surface (CMS)Blank Detail Specification: Fixed low power non-wire wound surface mounting (SMD) resistors31.040.10Fiksn
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

SIST
SIST EN 60115-1:2023(Main)
Fixed resistors for use in electronic equipment - Part 1: Generic specification (IEC 60115-1:2020 (MOD)
EN 60115-1:2023

This part of EN 60115 is a generic specification and is applicable to fixed resistors for use in electronic equipment.
It establishes standard terms, inspection procedures and methods of test for use in sectional and detail specifications of electronic components for quality assessment or any other purpose.

  • Standard
    177 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    179 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 140401-804:2011/A2:2019(Amendment)
Detail Specification: Fixed low power film high stability SMD resistors - Rectangular - Stability classes 0,1; 0,25
EN 140401-804:2011/A2:2019
  • Amendment
    4 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 140402:2015/A1:2017(Amendment)
Blank Detail Specification: Fixed low power wirewound surface mount (SMD) resistors
EN 140402:2015/A1:2016

Specific Amendment to the EN 140402 to add an Annex D which, owing to the nature of a Blank Detail Specification, consists of the blank template for the Annex with respective editorial comments.

  • Amendment
    4 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 140401-803:2008/A3:2017(Amendment)
Detail specification: Fixed low power film SMD resistors - Cylindrical - Stability classes 0,05; 0,1; 0,25; 0,5; 1; 2
EN 140401-803:2007/A3:2017

Amendment of the detail specification, aiming to amend the ordering information for a proper discrimination between two different permissible product variants.

  • Amendment
    5 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 140401-802:2008/A3:2017(Amendment)
Detail specification: Fixed low power film SMD resistors - Rectangular - Stability classes 1; 2
EN 140401-802:2007/A3:2017

Amendment of the detail specification, aiming to amend the ordering information for a proper discrimination between two different permissible product variants.

  • Amendment
    5 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 60195:2016(Main)
Method of measurement of current noise generated in fixed resistors (IEC 60195:2016)
EN 60195:2016

This International Standard specifies a method of measurement and associated test
conditions to assess the "noisiness", or magnitude of current noise, generated in fixed
resistors of any given type. The method applies to all classes of fixed resistors. The aim is to
provide comparable results for the determination of the suitability of resistors for use in
electronic circuits having critical noise requirements.
The current noise in resistive materials reflects the granular structure of the resistive material.
For some resistor technologies utilizing homogenous layers it is regarded as providing an
indication of defects, which are considered as a root cause for abnormal ageing of the
component under the influence of temperature and time.
The method described in this International Standard is not a general specification requirement
and therefore is applied if prescribed by a relevant component specification, or, if agreed
between a customer and a manufacturer.

  • Standard
    32 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 60115-8-1:2015(Main)
Fixed resistors for use in electronic equipment - Part 8-1: Blank detail specification: Fixed surface mount resistors categorized as level G - Assessment level EZ
EN 60115-8-1:2015

SIST EN 60115-8-1 specifies the characteristics and ratings of fixed surface mount (SMD) resistors. The resistors covered herein are classified to level G, as defined in IEC 60115-8-1, 1.5 for general electronic equipment, typically operated under benign or moderate environmental conditions, where the major requirement is function. Examples for level G include consumer products and telecommunication user terminals.

  • Standard
    52 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 60115-2:2015(Main)
Fixed resistors for use in electronic equipment - Part 2: Sectional specification : Fixed low-power non-wirewound resistors
EN 60115-2:2015

This part of IEC 60115 is applicable to leaded fixed low-power film resistors for use in
electronic equipment.
These resistors are typically described according to types (different geometric shapes) and
styles (different dimensions) and product technology. The resistive element of these resistors
is typically protected by a conformal lacquer coating. These resistors have wire terminations
and are primarily intended to be mounted on a circuit board in through-hole technique.
The object of this standard is to prescribe preferred ratings and characteristics and to select
from IEC 60115-1, the appropriate quality assessment procedures, tests and measuring
methods and to give general performance requirements for this type of resistor.

  • Standard
    82 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 60115-1:2012/A11:2015(Amendment)
Fixed resistors for use in electronic equipment - Part 1: Generic specification
EN 60115-1:2011/A11:2015

IEC 60115-1: 2008(E) is a generic specification and is applicable to fixed resistors for use in electronic equipment. It establishes standard terms, inspection procedures and methods of test for use in sectional and detail specifications of electronic components for quality assessment or any other purpose. This fourth edition cancels and replaces the third edition issued in 1999 and Amendment 1 (2001). It constitutes a technical revision. It contains the following significant technical changes with respect to the previous edition:  a) implementation of Annex Q which replaces Clause 3;  b) addition of new tests procedures in 4.34 through 4.38;  c) removal of the property 'temperature characteristics' from 4.8;  d) introduction of a new system of test severities for the shear test in  4.32;  e) introduction of new bias voltages for the damp heat steady-state test in 4.24;  f) furthermore, this fourth edition cancels and replaces the third edition published in 1999 and constitutes minor revisions related to tables, figures and references.

  • Amendment
    6 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 140402:2015(Main)
Blank Detail Specification: Fixed low power wirewound surface mount (SMD) resistors
EN 140402:2015

A blank detail specification is a supplementary document to the sectional specification and contains
requirements for style and layout and minimum content of detail specifications. Detail specifications not
complying with these requirements should not be considered as being in accordance with European
Standards nor should they be so described.
In the preparation of the detail specification the content of EN 60115-8:2012, 1.4 should be taken into
account.
The detail specification should be written by using the preferred values given in EN 60115-8.
The detail specification should contain a table of contents prior the first page of the actual specification.
For the use of SI units refer to EN ISO 80000-1, for the use of letter symbols to be used in electrical
technology, refer to EN 60027-1.

  • Standard
    32 pages
    English language
    sale 10% off
    e-Library read for
    1 day