SIST EN 300 220-1 V2.3.1:2010
(Main)Electromagnetic compatibility and Radio spectrum Matters (ERM) - Short Range Devices (SRD) - Radio equipment to be used in the 25 MHz to 1 000 MHz frequency range with power levels ranging up to 500 mW - Part 1: Technical characteristics and test methods
Electromagnetic compatibility and Radio spectrum Matters (ERM) - Short Range Devices (SRD) - Radio equipment to be used in the 25 MHz to 1 000 MHz frequency range with power levels ranging up to 500 mW - Part 1: Technical characteristics and test methods
The present document applies to the following Short Range Device major equipment types:
1) Non-specific Short Range Devices.
2) Alarms, identification systems, radio-determination, telecommand, telemetry, etc.
3) Radio Frequency Identification (RFID).
4) Detection, movement and alert applications.
These radio equipment types are capable of operating in the frequency bands within the 25 MHz to 1 000 MHz range as specified in table 1:
- either with a Radio Frequency (RF) output connection and dedicated antenna or with an integral antenna;
- for all types of modulation;
- with or without speech.
Table 1 shows a list of the frequency bands as designated to Short Range Devices by some European Commission Decisions [i.4] and [i.5] and the CEPT/ERC/REC 70-03 [i.1] as known at the date of publication of the present document.
NOTE 1: It should be noted that table 1 represents the most widely implemented position within the European Union and the CEPT countries, but it should not be assumed that all designated bands are available in all countries.
NOTE 2: In addition, it should be noted that other frequency bands may be available for short range devices in a country within the frequency range 25 MHz to 1 000 MHz covered by the present document. See European Commission Decisions on Short Range Devices [i.4] and [i.5] and CEPT/ERC/REC 70-03 [i.1] as implemented through National Radio Interfaces (NRI) or additional NRI as relevant.
NOTE 3: On non-harmonized parameters, national administrations may impose certain conditions such as the type of modulation, frequency, channel/frequency separations, maximum transmitter radiated power, duty cycle, and the inclusion of an automatic transmitter shut-off facility, as a condition for the issue of Individual Rights for use of spectrum or General Authorization, or as a condition for use under "licence exemption" as it is in most cases for Short Range Devices. The present document covers fixed stations, mobile stations and portable stations.
Elektromagnetna združljivost in zadeve v zvezi z radijskim spektrom (ERM) - Naprave kratkega dosega (SRD) - Radijska oprema, ki se uporablja v frekvenčnem območju od 25 MHz do 1000 MHz z močnostnimi nivoji do največ 500 mW - 1. del: Tehnične karakteristike in preskusne metode
Pričujoči dokument velja za naslednje glavne vrste opreme naprav kratkega dosega;
1) Nespecifične naprave kratkega dosega.
2) Alarme, sisteme za identifikacijo, radijsko lociranje, telekomando, telemetrijo itd.
3) Identifikacijo radijskih frekvenc (RFID).
4) Aplikacije zaznavanja, gibanja in alarmiranja.
Te vrste radijske opreme so zmožne delovanja v frekvenčnih pasovih znotraj razpona od 25 MHz do 1000 MHz, kot je določeno v preglednici 1:
- bodisi s povezavo z radio-frekvenčnim (RF) izhodom in namensko anteno ali z vgrajeno anteno;
- za vse vrste modulacij;
- z ali brez govora.
Preglednica 1 prikazuje seznam frekvenčnih pasov, kot je določen za naprave kratkega dosega z Odločbami Evropske komisije [i.4] in [i.5] in CEPT/ERC/REC 70-03 [i.1], kot je znan na datum objave pričujočega dokumenta.
OPOMBA 1: Treba je opozoriti, da preglednica 1 predstavlja najbolj splošno izvedeno postavko znotraj Evropske unije in držav članic CEPT, vendar se ne sme predpostavljati, da so vsi opredeljeni pasovi na voljo v vseh državah.
OPOMBA 2: Poleg tega je trebe opozoriti, da so napravam kratkega dosega znotraj razpona od 25 MHz do 1000 MHz, ki ga zajema pričujoči dokument, lahko na voljo drugi frekvenčni pasovi v državi. Glej Odločbe Evropske komisije o napravah kratkega dosega [i.4] in [i.5] in CEPT/ERC/REC 70-03 [i.1], kot se izvajajo s pomočjo državnih radijskih vmesnikov (NRI) ali dodatnih NRI.
OPOMBA 3: Na neharmoniziranih parametrih lahko državni upravni organi postavijo določene pogoje, kot na primer vrsto modulacije, frekvenco, ločevanje kanala/frekvence, maksimalno moč oddajanja oddajnika, obratovalni cikel in vključitev avtomatskih naprav za izklop oddajnikov, ki se zahtevajo za izdajo individualnih pravic za uporabo spektra ali za splošno avtorizacijo ali pa za uporabo z »licenčno izjemo«, kot velja v večini primerov za naprave kratkega dosega. Pričujoči dokument zajema stalne postaje, mobilne postaje in prenosne postaje.
General Information
Buy Standard
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Electromagnetic compatibility and Radio spectrum Matters (ERM) - Short Range Devices (SRD) - Radio equipment to be used in the 25 MHz to 1 000 MHz frequency range with power levels ranging up to 500 mW - Part 1: Technical characteristics and test methods33.100.01Elektromagnetna združljivost na splošnoElectromagnetic compatibility in general33.060.20Sprejemna in oddajna opremaReceiving and transmitting equipmentICS:Ta slovenski standard je istoveten z:EN 300 220-1 Version 2.3.1SIST EN 300 220-1 V2.3.1:2010en01-april-2010SIST EN 300 220-1 V2.3.1:2010SLOVENSKI
STANDARD
SIST EN 300 220-1 V2.3.1:2010
ETSI EN 300 220-1 V2.3.1 (2010-02)European Standard (Telecommunications series) Electromagnetic compatibilityand Radio spectrum Matters (ERM);Short Range Devices (SRD);Radio equipment to be used in the 25 MHz to 1 000 MHzfrequency range with power levels ranging up to 500 mW;Part 1: Technical characteristics and test methods SIST EN 300 220-1 V2.3.1:2010
ETSI ETSI EN 300 220-1 V2.3.1 (2010-02) 2
Reference REN/ERM-TG28-0420-1 Keywords radio, SRD, testing ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00
Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C Association à but non lucratif enregistrée à la Sous-Préfecture de Grasse (06) N° 7803/88
Important notice Individual copies of the present document can be downloaded from: http://www.etsi.org The present document may be made available in more than one electronic version or in print. In any case of existing or perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF). In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at http://portal.etsi.org/tb/status/status.asp If you find errors in the present document, please send your comment to one of the following services: http://portal.etsi.org/chaircor/ETSI_support.asp Copyright Notification No part may be reproduced except as authorized by written permission. The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2010. All rights reserved.
DECTTM, PLUGTESTSTM, UMTSTM, TIPHONTM, the TIPHON logo and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members. 3GPPTM is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. LTE™ is a Trade Mark of ETSI currently being registered for the benefit of its Members and of the 3GPP Organizational Partners. GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association. SIST EN 300 220-1 V2.3.1:2010
ETSI ETSI EN 300 220-1 V2.3.1 (2010-02) 3 Contents Intellectual Property Rights . 7 Foreword . 7 Introduction . 7 1 Scope . 9 2 References . 10 2.1 Normative references . 10 2.2 Informative references . 11 3 Definitions, symbols and abbreviations . 11 3.1 Definitions . 11 3.2 Symbols . 14 3.3 Abbreviations . 14 4 Technical requirement specifications . 15 4.1 General requirements . 15 4.1.1 Receiver category . 15 4.1.2 General performance criteria . 15 4.2 Presentation of equipment for testing purposes . 16 4.2.1 Choice of model for testing . 16 4.2.2 Testing of equipment with alternative power levels . 16 4.2.3 Testing of equipment that does not have an external 50 Ω RF connector (integral antenna equipment) . 16 4.2.3.1 Equipment with an internal permanent or temporary antenna connector or using a dedicated test fixture . 16 4.2.3.2 Equipment with a temporary antenna connector . 17 4.3 Mechanical and electrical design . 17 4.3.1 General . 17 4.3.2 Controls . 17 4.3.3 Transmitter shut-off facility . 17 4.3.4 Receiver mute or squelch . 17 4.3.5 Marking (equipment identification) . 17 4.4 Auxiliary test equipment . 17 5 Test conditions, power sources and ambient temperatures . 18 5.1 Normal and extreme test conditions . 18 5.2 Test power source . 18 5.2.1 External test power source . 18 5.2.2 Internal test power source . 18 5.3 Normal test conditions . 18 5.3.1 Normal temperature and humidity . 18 5.3.2 Normal test power source . 19 5.3.2.1 Mains voltage . 19 5.3.2.2 Regulated lead-acid battery power sources . 19 5.3.2.3 Other power sources . 19 5.4 Extreme test conditions . 19 5.4.1 Extreme temperatures . 19 5.4.1.1 Procedure for tests at extreme temperatures . 19 5.4.1.1.1 Procedure for equipment designed for continuous operation . 19 5.4.1.1.2 Procedure for equipment designed for intermittent operation . 20 5.4.1.2 Extreme temperature ranges . 20 5.4.2 Extreme test source voltages . 20 5.4.2.1 Mains voltage . 20 5.4.2.2 Regulated lead-acid battery power sources . 20 5.4.2.3 Power sources using other types of batteries . 21 5.4.2.4 Other power sources . 21 SIST EN 300 220-1 V2.3.1:2010
ETSI ETSI EN 300 220-1 V2.3.1 (2010-02) 4 6 General conditions . 21 6.1 Normal test signals and test modulation . 21 6.1.1 Normal test signals for analogue speech . 21 6.1.2 Normal test signals for data . 22 6.1.3 Testing of frequency agile or hopping equipment . 22 6.2 Artificial antenna . 22 6.3 Test fixture . 22 6.3.1 Validation of the test-fixture in the temperature chamber . 23 6.3.2 Mode of use . 25 6.4 Test sites and general arrangements for radiated measurements . 26 6.5 Modes of operation of the transmitter . 26 6.6 Measuring receiver . 26 7 Methods of measurement and limits for transmitter parameters . 27 7.1 Frequency error . 27 7.1.1 Definition . 27 7.1.2 Method of measurement . 27 7.1.3 Limits . 27 7.2 Average power (conducted) . 28 7.2.1 Definition . 28 7.2.2 Method of measurement . 28 7.2.3 Limits . 29 7.3 Effective radiated power . 31 7.3.1 Definition . 31 7.3.2 Methods of measurement . 31 7.3.3 Limits . 32 7.4 Spread spectrum modulation . 32 7.4.1 Frequency Hopping Spread Spectrum devices (FHSS) . 32 7.4.1.1 FHSS definitions . 32 7.4.1.2 FHSS declarations . 32 7.4.1.3 Limits . 33 7.4.2 Direct sequence or spread spectrum other than FHSS . 33 7.4.2.1 Definition . 33 7.4.2.2 Limits . 33 7.5 Transient power . 34 7.5.1 Definition . 34 7.5.2 Method of measurement . 34 7.5.3 Limits . 35 7.6 Adjacent channel power . 35 7.6.1 Definition . 35 7.6.2 Method of measurement . 35 7.6.3 Limits . 36 7.7 Modulation bandwidth . 36 7.7.1 Measurement applicability . 36 7.7.2 Method of measurement . 37 7.7.3 Limits . 38 7.8 Unwanted emissions in the spurious domain. 38 7.8.1 Definition . 38 7.8.2 Method of measurement . 39 7.8.2.1 Method of measuring the power level in a specified load, clause 7.8.1 a) i). 39 7.8.2.2 Method of measuring the effective radiated power, clause 7.8.1 a) ii) . 40 7.8.2.3 Method of measuring the effective radiated power, clause 7.8.1 b) . 41 7.8.3 Limits . 41 7.9 Frequency stability under low voltage conditions . 41 7.9.1 Definition . 41 7.9.2 Method of measurement . 41 7.9.3 Limits . 41 7.10 Duty Cycle. 41 7.10.1 Definitions . 42 7.10.2 Declaration . 42 7.10.3 Duty cycle limits . 42 7.11 Time-out-timer . 42 SIST EN 300 220-1 V2.3.1:2010
ETSI ETSI EN 300 220-1 V2.3.1 (2010-02) 5 7.11.1 Definition . 42 7.11.2 Declaration . 42 7.11.3 Limit . 42 8 Receiver parameters . 43 8.1 Receiver sensitivity . 43 8.1.1 Definition . 43 8.1.2 Method of measurement with continuous bit streams . 43 8.1.3 Method of measurement with messages . 44 8.1.4 Limits . 44 8.2 Receiver LBT threshold . 45 8.2.1 Definitions . 45 8.2.2 Method of measurements . 45 8.2.3 Limits . 46 8.3 Adjacent channel selectivity . 46 8.3.1 Definition . 46 8.3.2 Method of measurement . 47 8.3.3 Limits . 48 8.3.4 Receiver saturation at adjacent channel . 48 8.3.4.1 Definition . 48 8.3.4.2 Method of measurements . 48 8.3.4.3 Limits . 48 8.4 Blocking . 48 8.4.1 Definition . 48 8.4.2 Method of measurement . 49 8.4.3 Limit for blocking . 50 8.5 Spurious response rejection . 50 8.5.1 Definition . 50 8.5.2 Introduction to the method of measurement . 50 8.5.2.1 Method of measurement . 51 8.5.3 Limits for spurious response rejection . 51 8.6 Receiver spurious radiation . 52 8.6.1 Definition . 52 8.6.2 Method of measuring the power level in a specified load, clause 8.6.1 a) i) . 52 8.6.3 Method of measuring the effective radiated power, clause 8.6.1 a) ii) . 52 8.6.4 Method of measuring the effective radiated power, clause 8.6.1 b) . 53 8.6.5 Limits . 53 9 Spectrum access techniques . 54 9.1 Principle for Listen Before Talk (LBT) . 54 9.2 LBT timing parameters . 54 9.2.1 Minimum transmitter off-time . 54 9.2.1.1 Definition . 54 9.2.1.2 Limit . 54 9.2.2 LBT minimum listening time. 55 9.2.2.1 Definition . 55 9.2.2.2 Limit for minimum listening time . 55 9.2.3 Dead Time . 55 9.2.3.1 Definition . 55 9.2.3.2 Limit . 55 9.2.4 Acknowledge transmissions. 55 9.2.5 Maximum transmitter on-time . 56 9.2.5.1 Definition . 56 9.2.5.2 Limit . 56 9.2.5.2.1 Tx on-time for a single transmission . 56 9.2.5.2.2 Tx on-time for a transmission dialogue . 56 9.2.5.2.3 Maximum Tx on-time within a period of 1 hour for devices using LBT + AFA . 56 9.2.6 Declaration of LBT parameters . 56 9.2.7 Equipment with or without LBT using transmitter time-out-timer .
...
ETSI EN 300 220-1 V2.3.1 (2010-02)
European Standard (Telecommunications series)
Electromagnetic compatibility
and Radio spectrum Matters (ERM);
Short Range Devices (SRD);
Radio equipment to be used in the 25 MHz to 1 000 MHz
frequency range with power levels ranging up to 500 mW;
Part 1: Technical characteristics and test methods
---------------------- Page: 1 ----------------------
2 ETSI EN 300 220-1 V2.3.1 (2010-02)
Reference
REN/ERM-TG28-0420-1
Keywords
radio, SRD, testing
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
Individual copies of the present document can be downloaded from:
http://www.etsi.org
The present document may be made available in more than one electronic version or in print. In any case of existing or
perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF).
In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive
within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
http://portal.etsi.org/chaircor/ETSI_support.asp
Copyright Notification
No part may be reproduced except as authorized by written permission.
The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2010.
All rights reserved.
TM TM TM TM
DECT , PLUGTESTS , UMTS , TIPHON , the TIPHON logo and the ETSI logo are Trade Marks of ETSI registered
for the benefit of its Members.
TM
3GPP is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners.
LTE™ is a Trade Mark of ETSI currently being registered
for the benefit of its Members and of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI
---------------------- Page: 2 ----------------------
3 ETSI EN 300 220-1 V2.3.1 (2010-02)
Contents
Intellectual Property Rights . 7
Foreword . 7
Introduction . 7
1 Scope . 9
2 References . 10
2.1 Normative references . 10
2.2 Informative references . 11
3 Definitions, symbols and abbreviations . 11
3.1 Definitions . 11
3.2 Symbols . 14
3.3 Abbreviations . 14
4 Technical requirement specifications . 15
4.1 General requirements . 15
4.1.1 Receiver category . 15
4.1.2 General performance criteria . 15
4.2 Presentation of equipment for testing purposes . 16
4.2.1 Choice of model for testing . 16
4.2.2 Testing of equipment with alternative power levels . 16
4.2.3 Testing of equipment that does not have an external 50 Ω RF connector (integral antenna
equipment) . 16
4.2.3.1 Equipment with an internal permanent or temporary antenna connector or using a dedicated test
fixture . 16
4.2.3.2 Equipment with a temporary antenna connector . 17
4.3 Mechanical and electrical design . 17
4.3.1 General . 17
4.3.2 Controls . 17
4.3.3 Transmitter shut-off facility . 17
4.3.4 Receiver mute or squelch . 17
4.3.5 Marking (equipment identification) . 17
4.4 Auxiliary test equipment . 17
5 Test conditions, power sources and ambient temperatures . 18
5.1 Normal and extreme test conditions . 18
5.2 Test power source . 18
5.2.1 External test power source . 18
5.2.2 Internal test power source . 18
5.3 Normal test conditions . 18
5.3.1 Normal temperature and humidity . 18
5.3.2 Normal test power source . 19
5.3.2.1 Mains voltage . 19
5.3.2.2 Regulated lead-acid battery power sources . 19
5.3.2.3 Other power sources . 19
5.4 Extreme test conditions . 19
5.4.1 Extreme temperatures . 19
5.4.1.1 Procedure for tests at extreme temperatures . 19
5.4.1.1.1 Procedure for equipment designed for continuous operation . 19
5.4.1.1.2 Procedure for equipment designed for intermittent operation . 20
5.4.1.2 Extreme temperature ranges . 20
5.4.2 Extreme test source voltages . 20
5.4.2.1 Mains voltage . 20
5.4.2.2 Regulated lead-acid battery power sources . 20
5.4.2.3 Power sources using other types of batteries . 21
5.4.2.4 Other power sources . 21
ETSI
---------------------- Page: 3 ----------------------
4 ETSI EN 300 220-1 V2.3.1 (2010-02)
6 General conditions . 21
6.1 Normal test signals and test modulation . 21
6.1.1 Normal test signals for analogue speech . 21
6.1.2 Normal test signals for data . 22
6.1.3 Testing of frequency agile or hopping equipment . 22
6.2 Artificial antenna . 22
6.3 Test fixture . 22
6.3.1 Validation of the test-fixture in the temperature chamber . 23
6.3.2 Mode of use . 25
6.4 Test sites and general arrangements for radiated measurements . 26
6.5 Modes of operation of the transmitter . 26
6.6 Measuring receiver . 26
7 Methods of measurement and limits for transmitter parameters . 27
7.1 Frequency error . 27
7.1.1 Definition . 27
7.1.2 Method of measurement . 27
7.1.3 Limits . 27
7.2 Average power (conducted) . 28
7.2.1 Definition . 28
7.2.2 Method of measurement . 28
7.2.3 Limits . 29
7.3 Effective radiated power . 31
7.3.1 Definition . 31
7.3.2 Methods of measurement . 31
7.3.3 Limits . 32
7.4 Spread spectrum modulation . 32
7.4.1 Frequency Hopping Spread Spectrum devices (FHSS) . 32
7.4.1.1 FHSS definitions . 32
7.4.1.2 FHSS declarations . 32
7.4.1.3 Limits . 33
7.4.2 Direct sequence or spread spectrum other than FHSS . 33
7.4.2.1 Definition . 33
7.4.2.2 Limits . 33
7.5 Transient power . 34
7.5.1 Definition . 34
7.5.2 Method of measurement . 34
7.5.3 Limits . 35
7.6 Adjacent channel power . 35
7.6.1 Definition . 35
7.6.2 Method of measurement . 35
7.6.3 Limits . 36
7.7 Modulation bandwidth . 36
7.7.1 Measurement applicability . 36
7.7.2 Method of measurement . 37
7.7.3 Limits . 38
7.8 Unwanted emissions in the spurious domain. 38
7.8.1 Definition . 38
7.8.2 Method of measurement . 39
7.8.2.1 Method of measuring the power level in a specified load, clause 7.8.1 a) i). 39
7.8.2.2 Method of measuring the effective radiated power, clause 7.8.1 a) ii) . 40
7.8.2.3 Method of measuring the effective radiated power, clause 7.8.1 b) . 41
7.8.3 Limits . 41
7.9 Frequency stability under low voltage conditions . 41
7.9.1 Definition . 41
7.9.2 Method of measurement . 41
7.9.3 Limits . 41
7.10 Duty Cycle. 41
7.10.1 Definitions . 42
7.10.2 Declaration . 42
7.10.3 Duty cycle limits . 42
7.11 Time-out-timer . 42
ETSI
---------------------- Page: 4 ----------------------
5 ETSI EN 300 220-1 V2.3.1 (2010-02)
7.11.1 Definition . 42
7.11.2 Declaration . 42
7.11.3 Limit . 42
8 Receiver parameters . 43
8.1 Receiver sensitivity . 43
8.1.1 Definition . 43
8.1.2 Method of measurement with continuous bit streams . 43
8.1.3 Method of measurement with messages . 44
8.1.4 Limits . 44
8.2 Receiver LBT threshold . 45
8.2.1 Definitions . 45
8.2.2 Method of measurements . 45
8.2.3 Limits . 46
8.3 Adjacent channel selectivity . 46
8.3.1 Definition . 46
8.3.2 Method of measurement . 47
8.3.3 Limits . 48
8.3.4 Receiver saturation at adjacent channel . 48
8.3.4.1 Definition . 48
8.3.4.2 Method of measurements . 48
8.3.4.3 Limits . 48
8.4 Blocking . 48
8.4.1 Definition . 48
8.4.2 Method of measurement . 49
8.4.3 Limit for blocking . 50
8.5 Spurious response rejection . 50
8.5.1 Definition . 50
8.5.2 Introduction to the method of measurement . 50
8.5.2.1 Method of measurement . 51
8.5.3 Limits for spurious response rejection . 51
8.6 Receiver spurious radiation . 52
8.6.1 Definition . 52
8.6.2 Method of measuring the power level in a specified load, clause 8.6.1 a) i) . 52
8.6.3 Method of measuring the effective radiated power, clause 8.6.1 a) ii) . 52
8.6.4 Method of measuring the effective radiated power, clause 8.6.1 b) . 53
8.6.5 Limits . 53
9 Spectrum access techniques . 54
9.1 Principle for Listen Before Talk (LBT) . 54
9.2 LBT timing parameters . 54
9.2.1 Minimum transmitter off-time . 54
9.2.1.1 Definition . 54
9.2.1.2 Limit . 54
9.2.2 LBT minimum listening time. 55
9.2.2.1 Definition . 55
9.2.2.2 Limit for minimum listening time . 55
9.2.3 Dead Time . 55
9.2.3.1 Definition . 55
9.2.3.2 Limit . 55
9.2.4 Acknowledge transmissions. 55
9.2.5 Maximum transmitter on-time . 56
9.2.5.1 Definition . 56
9.2.5.2 Limit . 56
9.2.5.2.1 Tx on-time for a single transmission . 56
9.2.5.2.2 Tx on-time for a transmission dialogue . 56
9.2.5.2.3 Maximum Tx on-time within a period of 1 hour for devices using LBT + AFA . 56
9.2.6 Declaration of LBT parameters . 56
9.2.7 Equipment with or without LBT using transmitter time-out-timer . 56
10 Measurement uncertainty . 57
Annex A (normative): Radiated measurement . 58
ETSI
---------------------- Page: 5 --------
...
Final draft ETSI EN 300 220-1 V2.3.1 (2009-12)
European Standard (Telecommunications series)
Electromagnetic compatibility
and Radio spectrum Matters (ERM);
Short Range Devices (SRD);
Radio equipment to be used in the 25 MHz to 1 000 MHz
frequency range with power levels ranging up to 500 mW;
Part 1: Technical characteristics and test methods
---------------------- Page: 1 ----------------------
2 Final draft ETSI EN 300 220-1 V2.3.1 (2009-12)
Reference
REN/ERM-TG28-0420-1
Keywords
radio, SRD, testing
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
Individual copies of the present document can be downloaded from:
http://www.etsi.org
The present document may be made available in more than one electronic version or in print. In any case of existing or
perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF).
In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive
within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
http://portal.etsi.org/chaircor/ETSI_support.asp
Copyright Notification
No part may be reproduced except as authorized by written permission.
The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2009.
All rights reserved.
TM TM TM TM
DECT , PLUGTESTS , UMTS , TIPHON , the TIPHON logo and the ETSI logo are Trade Marks of ETSI registered
for the benefit of its Members.
TM
3GPP is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners.
LTE™ is a Trade Mark of ETSI currently being registered
for the benefit of its Members and of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI
---------------------- Page: 2 ----------------------
3 Final draft ETSI EN 300 220-1 V2.3.1 (2009-12)
Contents
Intellectual Property Rights . 7
Foreword . 7
Introduction . 7
1 Scope . 9
2 References . 10
2.1 Normative references . 10
2.2 Informative references . 11
3 Definitions, symbols and abbreviations . 11
3.1 Definitions . 11
3.2 Symbols . 14
3.3 Abbreviations . 14
4 Technical requirement specifications . 15
4.1 General requirements . 15
4.1.1 Receiver category . 15
4.1.2 General performance criteria . 15
4.2 Presentation of equipment for testing purposes . 16
4.2.1 Choice of model for testing . 16
4.2.2 Testing of equipment with alternative power levels . 16
4.2.3 Testing of equipment that does not have an external 50 Ω RF connector (integral antenna
equipment) . 16
4.2.3.1 Equipment with an internal permanent or temporary antenna connector or using a dedicated test
fixture . 16
4.2.3.2 Equipment with a temporary antenna connector . 17
4.3 Mechanical and electrical design . 17
4.3.1 General . 17
4.3.2 Controls . 17
4.3.3 Transmitter shut-off facility . 17
4.3.4 Receiver mute or squelch . 17
4.3.5 Marking (equipment identification) . 17
4.4 Auxiliary test equipment . 17
5 Test conditions, power sources and ambient temperatures . 18
5.1 Normal and extreme test conditions . 18
5.2 Test power source . 18
5.2.1 External test power source . 18
5.2.2 Internal test power source . 18
5.3 Normal test conditions . 18
5.3.1 Normal temperature and humidity . 18
5.3.2 Normal test power source . 19
5.3.2.1 Mains voltage . 19
5.3.2.2 Regulated lead-acid battery power sources . 19
5.3.2.3 Other power sources . 19
5.4 Extreme test conditions . 19
5.4.1 Extreme temperatures . 19
5.4.1.1 Procedure for tests at extreme temperatures . 19
5.4.1.1.1 Procedure for equipment designed for continuous operation . 19
5.4.1.1.2 Procedure for equipment designed for intermittent operation . 20
5.4.1.2 Extreme temperature ranges . 20
5.4.2 Extreme test source voltages . 20
5.4.2.1 Mains voltage . 20
5.4.2.2 Regulated lead-acid battery power sources . 20
5.4.2.3 Power sources using other types of batteries . 21
5.4.2.4 Other power sources . 21
ETSI
---------------------- Page: 3 ----------------------
4 Final draft ETSI EN 300 220-1 V2.3.1 (2009-12)
6 General conditions . 21
6.1 Normal test signals and test modulation . 21
6.1.1 Normal test signals for analogue speech . 21
6.1.2 Normal test signals for data . 22
6.1.3 Testing of frequency agile or hopping equipment . 22
6.2 Artificial antenna . 22
6.3 Test fixture . 22
6.3.1 Validation of the test-fixture in the temperature chamber . 23
6.3.2 Mode of use . 25
6.4 Test sites and general arrangements for radiated measurements . 26
6.5 Modes of operation of the transmitter . 26
6.6 Measuring receiver . 26
7 Methods of measurement and limits for transmitter parameters . 27
7.1 Frequency error . 27
7.1.1 Definition . 27
7.1.2 Method of measurement . 27
7.1.3 Limits . 27
7.2 Average power (conducted) . 28
7.2.1 Definition . 28
7.2.2 Method of measurement . 28
7.2.3 Limits . 29
7.3 Effective radiated power . 31
7.3.1 Definition . 31
7.3.2 Methods of measurement . 31
7.3.3 Limits . 32
7.4 Spread spectrum modulation . 32
7.4.1 Frequency Hopping Spread Spectrum devices (FHSS) . 32
7.4.1.1 FHSS definitions . 32
7.4.1.2 FHSS declarations . 32
7.4.1.3 Limits . 33
7.4.2 Direct sequence or spread spectrum other than FHSS . 33
7.4.2.1 Definition . 33
7.4.2.2 Limits . 33
7.5 Transient power . 34
7.5.1 Definition . 34
7.5.2 Method of measurement . 34
7.5.3 Limits . 35
7.6 Adjacent channel power . 35
7.6.1 Definition . 35
7.6.2 Method of measurement . 35
7.6.3 Limits . 36
7.7 Modulation bandwidth . 36
7.7.1 Measurement applicability . 36
7.7.2 Method of measurement . 37
7.7.3 Limits . 38
7.8 Unwanted emissions in the spurious domain. 38
7.8.1 Definition . 38
7.8.2 Method of measurement . 39
7.8.2.1 Method of measuring the power level in a specified load, clause 7.8.1 a) i). 39
7.8.2.2 Method of measuring the effective radiated power, clause 7.8.1 a) ii) . 40
7.8.2.3 Method of measuring the effective radiated power, clause 7.8.1 b) . 41
7.8.3 Limits . 41
7.9 Frequency stability under low voltage conditions . 41
7.9.1 Definition . 41
7.9.2 Method of measurement . 41
7.9.3 Limits . 41
7.10 Duty Cycle. 41
7.10.1 Definitions . 42
7.10.2 Declaration . 42
7.10.3 Duty cycle limits . 42
7.11 Time-out-timer . 42
ETSI
---------------------- Page: 4 ----------------------
5 Final draft ETSI EN 300 220-1 V2.3.1 (2009-12)
7.11.1 Definition . 42
7.11.2 Declaration . 42
7.11.3 Limit . 42
8 Receiver parameters . 43
8.1 Receiver sensitivity . 43
8.1.1 Definition . 43
8.1.2 Method of measurement with continuous bit streams . 43
8.1.3 Method of measurement with messages . 44
8.1.4 Limits . 45
8.2 Receiver LBT threshold . 45
8.2.1 Definitions . 45
8.2.2 Method of measurements . 45
8.2.3 Limits . 46
8.3 Adjacent channel selectivity . 46
8.3.1 Definition . 46
8.3.2 Method of measurement . 47
8.3.3 Limits . 48
8.3.4 Receiver saturation at adjacent channel . 48
8.3.4.1 Definition . 48
8.3.4.2 Method of measurements . 48
8.3.4.3 Limits . 48
8.4 Blocking . 48
8.4.1 Definition . 48
8.4.2 Method of measurement . 49
8.4.3 Limit for blocking . 50
8.5 Spurious response rejection . 50
8.5.1 Definition . 50
8.5.2 Introduction to the method of measurement . 50
8.5.2.1 Method of measurement . 51
8.5.3 Limits for spurious response rejection . 51
8.6 Receiver spurious radiation . 52
8.6.1 Definition . 52
8.6.2 Method of measuring the power level in a specified load, clause 8.6.1 a) i) . 52
8.6.3 Method of measuring the effective radiated power, clause 8.6.1 a) ii) . 52
8.6.4 Method of measuring the effective radiated power, clause 8.6.1 b) . 53
8.6.5 Limits . 53
9 Spectrum access techniques . 54
9.1 Principle for Listen Before Talk (LBT) . 54
9.2 LBT timing parameters . 54
9.2.1 Minimum transmitter off-time . 54
9.2.1.1 Definition . 54
9.2.1.2 Limit . 54
9.2.2 LBT minimum listening time. 55
9.2.2.1 Definition . 55
9.2.2.2 Limit for minimum listening time . 55
9.2.3 Dead Time . 55
9.2.3.1 Definition . 55
9.2.3.2 Limit . 55
9.2.4 Acknowledge transmissions. 55
9.2.5 Maximum transmitter on-time . 56
9.2.5.1 Definition . 56
9.2.5.2 Limit . 56
9.2.5.2.1 Tx on-time for a single transmission . 56
9.2.5.2.2 Tx on-time for a transmission dialogue . 56
9.2.5.2.3 Maximum Tx on-time within a period of 1 hour for devices using LBT + AFA . 56
9.2.6 Declaration of LBT parameters . 56
9.2.7 Equipment with or without LBT using transmitter time-out-timer . 56
10 Measurement uncertainty . 57
Annex A (normative): Radiated measurement .
...
Draft ETSI EN 300 220-1 V2.3.1 (2009-04)
European Standard (Telecommunications series)
Electromagnetic compatibility
and Radio spectrum Matters (ERM);
Short Range Devices (SRD);
Radio equipment to be used in the 25 MHz to 1 000 MHz
frequency range with power levels ranging up to 500 mW;
Part 1: Technical characteristics and test methods
---------------------- Page: 1 ----------------------
2 Draft ETSI EN 300 220-1 V2.3.1 (2009-04)
Reference
REN/ERM-TG28-0420-1
Keywords
radio, SRD, testing
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
Individual copies of the present document can be downloaded from:
http://www.etsi.org
The present document may be made available in more than one electronic version or in print. In any case of existing or
perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF).
In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive
within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
http://portal.etsi.org/chaircor/ETSI_support.asp
Copyright Notification
No part may be reproduced except as authorized by written permission.
The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2009.
All rights reserved.
TM TM TM TM
DECT , PLUGTESTS , UMTS , TIPHON , the TIPHON logo and the ETSI logo are Trade Marks of ETSI registered
for the benefit of its Members.
TM
3GPP is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners.
LTE™ is a Trade Mark of ETSI currently being registered
for the benefit of its Members and of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI
---------------------- Page: 2 ----------------------
3 Draft ETSI EN 300 220-1 V2.3.1 (2009-04)
Contents
Intellectual Property Rights . 7
Foreword . 7
Introduction . 7
1 Scope . 9
2 References . 10
2.1 Normative references . 10
2.2 Informative references . 10
3 Definitions, symbols and abbreviations . 11
3.1 Definitions . 11
3.2 Symbols . 13
3.3 Abbreviations . 13
4 Technical requirement specifications . 14
4.1 General requirements . 14
4.1.1 Receiver category . 14
4.1.2 General performance criteria . 14
4.2 Presentation of equipment for testing purposes . 15
4.2.1 Choice of model for testing . 15
4.2.2 Testing of equipment with alternative power levels . 15
4.2.3 Testing of equipment that does not have an external 50 Ω RF connector (integral antenna
equipment) . 16
4.2.3.1 Equipment with an internal permanent or temporary antenna connector or using a dedicated test
fixture . 16
4.2.3.2 Equipment with a temporary antenna connector . 16
4.3 Mechanical and electrical design . 16
4.3.1 General . 16
4.3.2 Controls . 16
4.3.3 Transmitter shut-off facility . 16
4.3.4 Receiver mute or squelch . 16
4.3.5 Marking (equipment identification) . 16
4.4 Auxiliary test equipment . 17
5 Test conditions, power sources and ambient temperatures . 17
5.1 Normal and extreme test conditions . 17
5.2 Test power source . 17
5.2.1 External test power source . 17
5.2.2 Internal test power source . 17
5.3 Normal test conditions . 18
5.3.1 Normal temperature and humidity . 18
5.3.2 Normal test power source . 18
5.3.2.1 Mains voltage . 18
5.3.2.2 Regulated lead-acid battery power sources . 18
5.3.2.3 Other power sources . 18
5.4 Extreme test conditions . 18
5.4.1 Extreme temperatures . 18
5.4.1.1 Procedure for tests at extreme temperatures . 18
5.4.1.1.1 Procedure for equipment designed for continuous operation . 19
5.4.1.1.2 Procedure for equipment designed for intermittent operation . 19
5.4.1.2 Extreme temperature ranges . 19
5.4.2 Extreme test source voltages . 19
5.4.2.1 Mains voltage . 19
5.4.2.2 Regulated lead-acid battery power sources . 19
5.4.2.3 Power sources using other types of batteries . 20
5.4.2.4 Other power sources . 20
ETSI
---------------------- Page: 3 ----------------------
4 Draft ETSI EN 300 220-1 V2.3.1 (2009-04)
6 General conditions . 20
6.1 Normal test signals and test modulation . 20
6.1.1 Normal test signals for analogue speech . 20
6.1.2 Normal test signals for data . 21
6.1.3 Testing of frequency agile or hopping equipment . 21
6.2 Artificial antenna . 21
6.3 Test fixture . 21
6.3.1 Validation of the test-fixture in the temperature chamber . 22
6.3.2 Mode of use . 24
6.4 Test sites and general arrangements for radiated measurements . 24
6.5 Modes of operation of the transmitter . 24
6.6 Measuring receiver . 25
7 Methods of measurement and limits for transmitter parameters . 25
7.1 Frequency error . 26
7.1.1 Definition . 26
7.1.2 Method of measurement . 26
7.1.3 Limits . 26
7.2 Average power (conducted) . 27
7.2.1 Definition . 27
7.2.2 Method of measurement . 27
7.2.3 Limits . 27
7.3 Effective radiated power . 29
7.3.1 Definition . 29
7.3.2 Methods of measurement . 29
7.3.3 Limits . 30
7.4 Spread spectrum modulation . 30
7.4.1 Frequency Hopping Spread Spectrum devices (FHSS) . 30
7.4.1.1 FHSS definitions . 30
7.4.1.2 FHSS declarations . 31
7.4.1.3 Limits . 31
7.4.2 Direct sequence or spread spectrum other than FHSS . 31
7.4.2.1 Definition . 31
7.4.2.2 Limits . 32
7.5 Transient power . 32
7.5.1 Definition . 32
7.5.2 Method of measurement . 32
7.5.3 Limits . 33
7.6 Adjacent channel power . 33
7.6.1 Definition . 33
7.6.2 Method of measurement . 33
7.6.3 Limits . 35
7.7 Modulation bandwidth . 35
7.7.1 Measurement applicability . 35
7.7.2 Method of measurement . 36
7.7.3 Limits . 36
7.8 Unwanted emissions in the spurious domain. 37
7.8.1 Definition . 37
7.8.2 Method of measurement . 37
7.8.2.1 Method of measuring the power level in a specified load, clause 7.8.1 a) i). 37
7.8.2.2 Method of measuring the effective radiated power, clause 7.8.1 a) ii) . 38
7.8.2.3 Method of measuring the effective radiated power, clause 7.8.1 b) . 39
7.8.3 Limits . 39
7.9 Frequency stability under low voltage conditions . 39
7.9.1 Definition . 39
7.9.2 Method of measurement . 39
7.9.3 Limits . 40
7.10 Duty Cycle. 40
7.10.1 Definitions . 40
7.10.2 Declaration . 40
7.10.3 Duty cycle limits . 40
7.11 Time-out-timer . 40
ETSI
---------------------- Page: 4 ----------------------
5 Draft ETSI EN 300 220-1 V2.3.1 (2009-04)
7.11.1 Definition . 40
7.11.2 Declaration . 41
7.11.3 Limit . 41
8 Receiver parameters . 41
8.1 Receiver sensitivity . 41
8.1.1 Definition . 41
8.1.2 Method of measurement with continuous bit streams . 41
8.1.3 Method of measurement with messages . 42
8.1.4 Limits . 43
8.2 Receiver LBT threshold . 43
8.2.1 Definitions . 43
8.2.2 Method of measurements . 43
8.2.3 Limits . 44
8.3 Adjacent channel selectivity . 45
8.3.1 Definition . 45
8.3.2 Method of measurement . 45
8.3.3 Limits . 47
8.3.4 Receiver saturation at adjacent channel . 47
8.3.4.1 Definition . 47
8.3.4.2 Method of measurements . 47
8.3.4.3 Limits . 48
8.4 Blocking . 48
8.4.1 Definition . 48
8.4.2 Method of measurement . 48
8.4.3 Limit for blocking . 50
8.5 Spurious response rejection . 50
8.5.1 Definition . 50
8.5.2 Introduction to the method of measurement . 51
8.5.2.1 Method of measurement . 52
8.5.3 Limits for spurious response rejection . 53
8.6 Receiver spurious radiation . 53
8.6.1 Definition . 53
8.6.2 Method of measuring the power level in a specified load, clause 8.6.1 a) i) . 53
8.6.3 Method of measuring the effective radiated power, clause 8.6.1 a) ii) . 54
8.6.4 Method of measuring the effective radiated power, clause 8.6.1 b) . 55
8.6.5 Limits . 55
9 Spectrum access techniques . 55
9.1 Principle for Listen Before Talk (LBT) . 55
9.2 LBT timing parameters . 56
9.2.1 Minimum transmitter off-time . 56
9.2.1.1 Definition . 56
9.2.1.2 Limit . 56
9.2.2 LBT minimum listening time. 56
9.2.2.1 Definition . 56
9.2.2.2 Limit for minimum listening time . 56
9.2.3 Dead Time . 57
9.2.3.1 Definition . 57
9.2.3.2 Limit . 57
9.2.4 Acknowledge transmissions. 57
9.2.5 Maximum transmitter on-time . 57
9.2.5.1 Definition . 57
9.2.5.2 Limit . 57
9.2.5.2.1 Tx on-time for a single transmission . 57
9.2.5.2.2 Tx on-time for a transmission dialogue . 58
9.2.5.2.3 Maximum Tx on-time within a period of 1 hour for devices using LBT + AFA . 58
9.2.6 Declaration of LBT parameters . 58
9.2.7 Equipment with or without LBT using transmitter time-out-timer . 58
10 Measurement uncertainty . 58
Annex A (normative): Radiated measurement . 60
ETSI
-------------
...
Draft ETSI EN 300 220-1 V2.2.1 (2008-04)
European Standard (Telecommunications series)
Electromagnetic compatibility
and Radio spectrum Matters (ERM);
Short Range Devices (SRD);
Radio equipment to be used in the 25 MHz to 1 000 MHz
frequency range with power levels ranging up to 500 mW;
Part 1: Technical characteristics and test methods
---------------------- Page: 1 ----------------------
2 Draft ETSI EN 300 220-1 V2.2.1 (2008-04)
Reference
REN/ERM-TG28-0420-1
Keywords
radio, SRD, testing
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
Individual copies of the present document can be downloaded from:
http://www.etsi.org
The present document may be made available in more than one electronic version or in print. In any case of existing or
perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF).
In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive
within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
http://portal.etsi.org/chaircor/ETSI_support.asp
Copyright Notification
No part may be reproduced except as authorized by written permission.
The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2008.
All rights reserved.
TM TM TM TM
DECT , PLUGTESTS , UMTS , TIPHON , the TIPHON logo and the ETSI logo are Trade Marks of ETSI registered
for the benefit of its Members.
TM
3GPP is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners.
ETSI
---------------------- Page: 2 ----------------------
3 Draft ETSI EN 300 220-1 V2.2.1 (2008-04)
Contents
Intellectual Property Rights.7
Foreword.7
Introduction .7
1 Scope.9
2 References.10
2.1 Normative references.10
2.2 Informative references.11
3 Definitions, symbols and abbreviations .11
3.1 Definitions.11
3.2 Symbols.13
3.3 Abbreviations.13
4 Technical requirement specifications.14
4.1 General requirements.14
4.1.1 Receiver category.14
4.1.2 General performance criteria .14
4.2 Presentation of equipment for testing purposes.15
4.2.1 Choice of model for testing .15
4.2.2 Testing of equipment with alternative power levels .15
4.2.3 Testing of equipment that does not have an external 50 Ω RF connector (integral antenna
equipment) .15
4.2.3.1 Equipment with an internal permanent or temporary antenna connector or using a dedicated test
fixture.15
4.2.3.2 Equipment with a temporary antenna connector.16
4.3 Mechanical and electrical design.16
4.3.1 General.16
4.3.2 Controls.16
4.3.3 Transmitter shut-off facility.16
4.3.4 Receiver mute or squelch.16
4.3.5 Marking (equipment identification).16
4.4 Auxiliary test equipment .16
4.5 Interpretation of the measurement results .17
5 Test conditions, power sources and ambient temperatures .17
5.1 Normal and extreme test conditions .17
5.2 Test power source.17
5.2.1 External test power source.17
5.2.2 Internal test power source .17
5.3 Normal test conditions.18
5.3.1 Normal temperature and humidity.18
5.3.2 Normal test power source .18
5.3.2.1 Mains voltage.18
5.3.2.2 Regulated lead-acid battery power sources .18
5.3.2.3 Other power sources.18
5.4 Extreme test conditions .18
5.4.1 Extreme temperatures.18
5.4.1.1 Procedure for tests at extreme temperatures.18
5.4.1.1.1 Procedure for equipment designed for continuous operation .19
5.4.1.1.2 Procedure for equipment designed for intermittent operation .19
5.4.1.2 Extreme temperature ranges.19
5.4.2 Extreme test source voltages.19
5.4.2.1 Mains voltage.19
5.4.2.2 Regulated lead-acid battery power sources .19
5.4.2.3 Power sources using other types of batteries.20
5.4.2.4 Other power sources.20
ETSI
---------------------- Page: 3 ----------------------
4 Draft ETSI EN 300 220-1 V2.2.1 (2008-04)
6 General conditions.20
6.1 Normal test signals and test modulation.20
6.1.1 Normal test signals for analogue speech.20
6.1.2 Normal test signals for data .21
6.1.3 Testing of frequency agile or hopping equipment .21
6.2 Artificial antenna.21
6.3 Test fixture.21
6.3.1 Validation of the test-fixture in the temperature chamber .22
6.3.2 Mode of use .24
6.4 Test sites and general arrangements for radiated measurements .24
6.5 Modes of operation of the transmitter .24
6.6 Measuring receiver.25
7 Methods of measurement and limits for transmitter parameters .25
7.1 Frequency error.26
7.1.1 Definition.26
7.1.2 Method of measurement.26
7.1.2.1 Method of measurement for equipment with unmodulated carrier test mode.26
7.1.3 Limits.26
7.2 Carrier power (conducted).26
7.2.1 Definition.27
7.2.2 Method of measurement.27
7.2.3 Limits.27
7.3 Effective radiated power .29
7.3.1 Definition.29
7.3.2 Methods of measurement.29
7.3.3 Limits.30
7.4 Spread spectrum modulation.30
7.4.1 Frequency Hopping Spread Spectrum devices (FHSS) .30
7.4.1.1 FHSS definitions.30
7.4.1.2 FHSS declarations.30
7.4.1.3 Limits.31
7.4.2 Direct sequence or spread spectrum other than FHSS .31
7.4.2.1 Definition.31
7.4.2.2 Limits.31
7.5 Void.32
7.6 Adjacent channel power .32
7.6.1 Definition.32
7.6.2 Method of measurement.32
7.6.3 Limits.33
7.7 Bandwidth for non-channelized equipment.34
7.7.1 Definition.34
7.7.2 Measurement applicability.34
7.7.3 Method of measurement.34
7.7.4 Limits.34
7.8 Unwanted emissions in the spurious domain.34
7.8.1 Definition.34
7.8.2 Method of measuring the power level in a specified load, clause 7.8.1 a) i) .35
7.8.3 Method of measuring the effective radiated power, clause 7.8.1 a) ii) .35
7.8.4 Method of measuring the effective radiated power, clause 7.8.1 b) .36
7.8.5 Limits.37
7.9 Frequency stability under low voltage conditions .37
7.9.1 Definition.37
7.9.2 Method of measurement.37
7.9.3 Limits.37
7.10 Duty Cycle.37
7.10.1 Definitions.37
7.10.2 Declaration.38
7.10.3 Duty cycle limits.38
8 Receiver parameters .38
8.1 Maximum usable sensitivity (conducted).39
ETSI
---------------------- Page: 4 ----------------------
5 Draft ETSI EN 300 220-1 V2.2.1 (2008-04)
8.1.1 Definition.39
8.1.2 Method of measurement with continuous bit streams.39
8.1.3 Method of measurement with messages .40
8.1.4 Limits.40
8.2 Receiver LBT threshold and transmitter max on-time .41
8.2.1 Definitions.41
8.2.2 Method of measurements.41
8.2.3 Limits.42
8.3 Adjacent channel selectivity.42
8.3.1 Definition.42
8.3.2 Method of measurement.43
8.3.3 Limits.43
8.3.3.1 Limit for adjacent channel selectivity .43
8.3.3.2 Limit for receiver saturation at adjacent channel .44
8.3.3.2.1 Definition.44
8.3.3.2.2 Method of measurements.44
8.3.3.2.3 Limits.44
8.4 Blocking or desensitization .44
8.4.1 Definition.44
8.4.2 Method of measurement.44
8.4.3 Limit for blocking.45
8.5 Receiver spurious radiation .45
8.5.1 Definition.45
8.5.2 Method of measuring the power level in a specified load, clause 8.5.1 a) i) .45
8.5.3 Method of measuring the effective radiated power, clause 8.5.1 a) ii) .46
8.5.4 Method of measuring the effective radiated power, clause 8.5.1 b) .47
8.5.5 Limits.47
9 Spectrum access techniques .47
9.1 Principle for Listen Before Talk (LBT).47
9.1.1 LBT timing parameters.48
9.1.1.1 Minimum transmitter off-time .48
9.1.1.1.1 Definition.48
9.1.1.1.2 Limit.48
9.1.1.2 LBT minimum listening time.48
9.1.1.2.1 Definition.48
9.1.1.2.2 Limit for minimum listening time .48
9.1.1.3 Acknowledge transmissions.49
9.1.1.4 Maximum transmitter on-time .49
9.1.1.4.1 Definition.49
9.1.1.4.2 Limit.49
9.1.1.5 Declaration of LBT parameters.49
9.1.1.6 Equipment with or without LBT using transmitter time-out-timer .49
10 Measurement uncertainty .50
Annex A (normative): Radiated measurement.51
A.1 Test sites and general arrangements for measurements involving the use of radiated fields .51
A.1.1 Anechoic Chamber.51
A.1.2 Anechoic Chamber with a conductive ground plane.52
A.1.3 Open Area Test Site (OATS) .53
A.1.4 Test antenna.54
A.1.5 Substitution antenna.54
A.1.6 Measuring antenna.55
A.2 Guidance on the use of radiation test sites .55
A.2.1 Verification of the test site .55
A.2.2 Preparation of the EUT.55
A.2.3 Power supplies to the EUT.55
A.2.4 Volume control setting for analogue speech tests .55
A.2.5 Range length.56
A.2.6 Site preparation.56
ETSI
---------------------- Page: 5 ----------------------
6 Draft ETSI EN 300 220-1 V2.2.1 (2008-04)
A.3 Coupling of signals.57
A.3.1 General.57
A.3.2 Data Signals.57
A.3.3 Speech and analogue signals .57
A.3.3.1 Acoustic coupler description.
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.