SIST EN 3506:2002

Aerospace series - Hot rolled sheets and plates in heat resisting alloys - Thickness 2,0 mm < = a < = 100 mm - Dimensions

This standard specifies the dimensions and tolerances of:
Hot rolled sheets and plates
in heat resisting alloys
Thickness 2,0 mm L a L 100 mm
for aerospace applications.

Luft- und Raumfahrt - Warmgewalzte Bleche und Platten aus hochwarmfesten Legierungen - Dicken 2,0 mm # a # 100 mm - Maße

Luft- und Raumfahrt - Warmgewalzte Bleche und Platten aus hochwarmfesten Legierungen - Dicken 2,0 mm # a # 100 mm - Maße

Série aérospatiale - Tôles et plaques épaisses laminées a chaud en alliages résistant a chaud - Épaisseurs 2,0 mm < = a < = 100 mm - Dimensions

Aerospace series - Hot rolled sheets and plates in heat resisting alloys - Thickness 2,0 mm < = a < = 100 mm - Dimensions

General Information

• Status: Published
• Publication Date: 31-Dec-2001
• ICS: 49.025.99 - Other materials
• Technical Committee: SS SPL - Technical Board for the general field
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 01-Jan-2002
• Due Date: 01-Jan-2002
• Completion Date: 01-Jan-2002
• Ref Project: EN 3506:2001 - Aerospace series - Hot rolled sheets and plates in heat resisting alloys - Thickness 2,0 mm < = a < = 100 mm - Dimensions

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Aerospace series - Hot rolled sheets and plates in heat resisting alloys - Thickness 2,0 mm < = a < = 100 mm - DimensionsLuft- und Raumfahrt - Warmgewalzte Bleche und Platten aus hochwarmfesten Legierungen - Dicken 2,0 mm # a # 100 mm - MaßeSérie aérospatiale - Tôles et plaques épaisses laminées a chaud en alliages résistant a chaud - Épaisseurs 2,0 mm < =
a < =
100 mm - DimensionsAerospace series - Hot rolled sheets and plates in heat resisting alloys - Thickness 2,0 mm < =
a < =
100 mm - Dimensions49.025.99Drugi materialiOther materialsICS:Ta slovenski standard je istoveten z:EN 3506:2001SIST EN 3506:2002en01-januar-2002SIST EN 3506:2002SLOVENSKI
STANDARD



SIST EN 3506:2002



EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 3506September 2001ICS 49.025.99English versionAerospace series - Hot rolled sheets and plates in heat resistingalloys - Thickness 2,0 mm
a
100 mm - DimensionsSérie aérospatiale - Tôles et plaques épaisses laminées àchaud en alliages résistant à chaud - Epaisseurs 2,0 mm a
100 mm - DimensionsLuft- und Raumfahrt - Warmgewalzte Bleche und Plattenaus hochwarmfesten Legierungen - Dicken 2,0 mm
a 100 mm - MaßeThis European Standard was approved by CEN on 2 May 2001.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2001 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 3506:2001 ESIST EN 3506:2002



EN 3506:2001 (E)2ForewordThis European Standard has been prepared by the European Association of Aerospace Manufacturers(AECMA).After inquiries and votes carried out in accordance with the rules of this Association, this Standard hasreceived the approval of the National Associations and the Official Services of the member countries ofAECMA, prior to its presentation to CEN.This European Standard shall be given the status of a national standard, either by publication of an identicaltext or by endorsement, at the latest by March 2002, and conflicting national standards shall be withdrawn atthe latest by March 2002.According to the CEN/CENELEC Internal Regulations, the national standards organizations of the followingcountrie
...