SIST EN 62561-1:2012
(Main)Lightning Protection System Components (LPSC) - Part 1: Requirements for connection components
Lightning Protection System Components (LPSC) - Part 1: Requirements for connection components
IEC 62561-1:2012(E) specifies the requirements and tests for metallic connection components that form part of a lightning protection system (LPS). Typically, these can be connectors, bonding and bridging components, expansion pieces and test joints. Testing of components for an explosive atmosphere is not covered by this standard.
Blitzschutzsystembauteile (LPSC) - Teil 1: Anforderungen an Verbindungsbauteile
Composants de systèmes de protection contre la foudre (CSPF) - Partie 1: Exigences pour les composants de connexion
L'IEC 62561-1:2012 spécifie les exigences et les essais à appliquer aux composants métalliques de connexion faisant partie d'un Système de Protection contre la Foudre (SPF). Il peut s'agir typiquement des connecteurs, composants de liaisons équipotentielles, de dérivation, pièces d'expansion, ainsi que les joints de contrôle. Les essais de composants pour atmosphère explosive ne sont pas concernés par la présente norme.
Elementi za zaščito pred strelo (LPSC) - 1. del: Zahteve za spojne komponente (IEC 62561-1:2012, spremenjen)
Ta del standarda IEC 62561 določa zahteve in preskuse za kovinske spojne komponente, ki so del sistema za zaščito pred strelo (LPS). Običajno so to lahko konektorji, vezne in premostitvene komponente, ekspanzijski kosi in preskusni spoji. Preskušanje komponent za eksplozivno atmosfero v tem standardu ni zajeto.
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Blitzschutzsystembauteile (LPSC) - Teil 1: Anforderungen an VerbindungsbauteileComposants de systèmes de protection contre la foudre (CSPF) - Partie 1: Exigences pour les composants de connexionLightning Protection System Components (LPSC) - Part 1: Requirements for connection components91.120.40Lightning protectionICS:Ta slovenski standard je istoveten z:EN 62561-1:2012SIST EN 62561-1:2012en01-julij-2012SIST EN 62561-1:2012SLOVENSKI
STANDARDSIST EN 50164-1:20081DGRPHãþD
SIST EN 62561-1:2012
EUROPEAN STANDARD EN 62561-1 NORME EUROPÉENNE
EUROPÄISCHE NORM June 2012
CENELEC European Committee for Electrotechnical Standardization Comité Européen de Normalisation Electrotechnique Europäisches Komitee für Elektrotechnische Normung
Management Centre: Avenue Marnix 17, B - 1000 Brussels
© 2012 CENELEC -
All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 62561-1:2012 E
ICS 29.020; 91.120.40 Supersedes EN 50164-1:2008English version
Lightning Protection System Components (LPSC) -
Part 1: Requirements for connection components (IEC 62561-1:2012, modified) Composants des systèmes de protectioncontre la foudre (CSPF) -Partie 1: Exigences pour les composantsde connexion (CEI 62561-1:2012, modifiée)
Blitzschutzsystembauteile (LPSC) -Teil 1: Anforderungen an Verbindungsbauteile (IEC 62561-1:2012, modifiziert) This European Standard was approved by CENELEC on 2012-03-16. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
SIST EN 62561-1:2012
EN 62561-1:2012 - 2 - Foreword The text of document 81/416/FDIS, future edition 1 of IEC 62561-1, prepared by IEC/TC 81, "Lightning protection", was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as EN 62561-1:2012. A draft amendment, which covers common modifications to IEC 62561-1 (81/416/FDIS), was prepared by CLC/TC 81X "Lightning protection" and approved by CENELEC. The following dates are fixed: – latest date by which this document has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2013-03-16 – latest date by which the national standards conflicting with this document have to be withdrawn (dow) 2015-03-16 This document supersedes EN 50164-1:2008. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such patent rights. Clauses, subclauses, notes, tables, figures and annexes which are additional to those in IEC 62561-1:2012 are prefixed “Z”. Endorsement notice The text of the International Standard IEC 62561-1:2012 was approved by CENELEC as a European Standard with agreed common modifications. SIST EN 62561-1:2012
- 3 - EN 62561-1:2012
COMMON MODIFICATIONS Whole document Replace all references to IEC 62305 by references to EN 62305. Replace all references to IEC 62561 by references to EN 62561. 4 Classification After 4.2, add the following: 4.Z1 Classification is also made according to its mechanical behaviour for connectors: a) declared to withstand static mechanical load 900 N; b) not intended to carry static mechanical load. 6 Tests Replace the whole 6.4 by the following: 6.4 Static mechanical test 6.4.Z1 General The static mechanical test is specifically applicable to the configurations B2/B3/B7 as shown in Annex B. For other applications, it is neither practical nor necessary to carry out static mechanical tests and is therefore not a requirement. For specific applications such as connectors embedded in concrete, it is not required to carry out mechanical tests. The test shall be performed with all conductor materials permitted according to the manufacturer's declaration. To minimize the number of tests, connectors that are used with several different conductor materials shall be performed using stainless steel. Any connector with a connection range equal to or less than 2 mm shall be tested on the minimum conductor size recommended. If the connection range is greater than 2 mm it shall be tested on the minimum and maximum size of conductor recommended. 6.4.Z2 Test procedure A second set of 3 new connectors shall be arranged according to the manufacturer's or supplier's installation instructions with the recommended conductor materials, sizes and tightening torques. Each conductor of the specimen assemblies shall be subjected independently to a mechanical tensile force of 900 N ± 20 N for 1 min.
The connection component is deemed to have passed the test if there is less than 1 mm movement of the conductor during the test and no damage on the connector or conductor. Annexes Annex C (normative) Conditioning/ageing for connection components In C.1, replace twice "IEC 60068-2-52:1996" by "EN 60068-2-52:1996". SIST EN 62561-1:2012
EN 62561-1:2012 - 4 - Add the following new annexes: Annex ZA (normative)
Normative references to international publications with their corresponding European publications The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. NOTE
Where an International Publication has been modified by common modifications, indicated by (mod), the relevant EN/HD applies. Publication Year Title EN/HD Year IEC 60068-2-52 + corr. July
1996 1996 Environmental testing -
Part 2: Tests - Test Kb: Salt mist, cyclic (sodium chloride solution) EN 60068-2-52 1996 IEC 62305-1 - Protection against lightning -
Part 1: General principles EN 62305-1 - IEC 62561-2 - Lightning Protection System Components (LPSC) - Part 2: Requirements for conductors and earth electrodes EN 62561-2 - ISO 6957 1988 Copper alloys - Ammonia test for stress corrosion resistance
- - ISO 6988 1985 Metallic and other non-organic coatings - Sulfur dioxide test with general condensation of moisture EN ISO 6988 1994
SIST EN 62561-1:2012
- 5 - EN 62561-1:2012
Annex ZB (informative)
Identification and differences of tests between EN 62561-1:2012 and EN 50164-1:2008 Table ZB.1 – Identification and differences of tests between EN 62561-1:2012 and EN 50164-1:2008 Test description EN 62561-1:2012 EN 50164-1:2008 Deviations / Remarks Test preparation 6.2 6.2 None Electrical test 6.3 6.3 Yes for screwless connection components Static mechanical test 6.4 – Yes Marking test 6.5 6.4 None
SIST EN 62561-1:2012
EN 62561-1:2012 - 6 -
Bibliography Add the following references: EN 62305-3, Protection against lightning – Part 3: Physical damage to structures and life hazard (IEC 62305-3) EN 62305-4, Protection against lightning – Part 4: Electrical and electronic systems within structures (IEC 62305-4)
SIST EN 62561-1:2012
IEC 62561-1 Edition 1.0 2012-02 INTERNATIONAL STANDARD Lightning protection system components (LPSC) –
Part 1: Requirements for connection components
INTERNATIONAL ELECTROTECHNICAL COMMISSION S ICS 29.020; 91.120.40 PRICE CODE ISBN 978-2-88912-925-6
® Registered trademark of the International Electrotechnical Commission ®
Warning! Make sure that you obtained this publication from an authorized distributor. SIST EN 62561-1:2012
– 2 – 62561-1 © IEC:2012(E) CONTENTS FOREWORD . 4 INTRODUCTION . 6 1 Scope . 7 2 Normative references . 7 3 Terms and definitions . 7 4 Classification . 8 5 Requirements . 9 5.1 General . 9 5.2 Installation instructions . 9 5.3 Lightning current carrying capability . 9 5.4 Static mechnical stress . 9 5.5 Screwed clamping connection . 9 5.6 Dismantling of test joints . 9 5.7 Damage to conductors and metal installations . 9 5.8 Safe connection . 10 5.9 Terminals of bonding bars . 10 5.10 Marking . 10 6 Tests . 10 6.1 General conditions for tests . 10 6.2 Test preparation . 11 6.2.1 Arrangement of the specimen . 11 6.2.2 Conditioning/ageing . 11 6.3 Electrical test . 11 6.4 Static mechanical test . 12 6.5 Marking test . 13 7 Electromagnetic compatibility (EMC) . 13 8 Structure and content of the test report . 13 8.1 General . 13 8.2 Report identification . 13 8.3 Specimen description . 13 8.4 Conductor . 14 8.5 Standards and references . 14 8.6 Test procedure . 14 8.7 Testing equipment description . 14 8.8 Measuring instruments description . 14 8.9 Results and parameters recorded . 14 8.10 Statement of pass/fail . 15 Annex A (informative)
Summary of the requirements and corresponding tests . 18 Annex B (informative)
Typical arrangements for various LPSCs . 19 Annex C (normative)
Conditioning/ageing for connection components . 20 Bibliography . 21
Figure 1 – Basic arrangement of specimen with cross connection component . 15 Figure 2 – Basic arrangement of specimen with parallel connection component . 16 Figure 3 – Basic arrangement of specimen with bridging component . 16 SIST EN 62561-1:2012
62561-1 © IEC:2012(E) – 3 – Figure 4 – Basic arrangement of specimen with equipotential bonding bar . 17 Figure 5 – Basic arrangement for contact measurement of expansion piece . 17
Table 1 – Lightning impulse current (Iimp) parameters . 12 Table A.1 – Requirements and corresponding tests . 18
SIST EN 62561-1:2012
– 4 – 62561-1 © IEC:2012(E) INTERNATIONAL ELECTROTECHNICAL COMMISSION ____________
LIGHTNING PROTECTION SYSTEM COMPONENTS (LPSC) –
Part 1: Requirements for connection components
FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non-governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any services carried out by independent certification bodies. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. International Standard IEC 62561-1 has been prepared by IEC technical committee 81: Lightning protection. The text of this standard is based on the following documents: FDIS Report on voting 81/416/FDIS 81/422A/RVD
Full information on the voting for the approval of this standard can be found in the report on voting indicated in the above table. This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. The content of this part of IEC 62561 is taken from European Standard EN 50164-1. SIST EN 62561-1:2012
62561-1 © IEC:2012(E) – 5 – A list of all the parts in the IEC 62561 series, published under the general title Lightning protection system components (LPSC), can be found on the IEC website.
The committee has decided that the contents of this publication will remain unchanged until the stability date indicated on the IEC web site under "http://webstore.iec.ch" in the data related to the specific publication. At this date, the publication will be
• reconfirmed, • withdrawn, • replaced by a revised edition, or • amended. A bilingual version of this publication may be issued at a later date. SIST EN 62561-1:2012
– 6 – 62561-1 © IEC:2012(E) INTRODUCTION This part of IEC 62561 deals with the requirements and tests for lightning protection system components (LPSC) used for the installation of a lightning protection system (LPS) designed and implemented according to the IEC 62305 series of standards.
SIST EN 62561-1:2012
62561-1 © IEC:2012(E) – 7 – LIGHTNING PROTECTION SYSTEM COMPONENTS (LPSC) –
Part 1: Requirements for connection components
1 Scope This part of IEC 62561 specifies the requirements and tests for metallic connection components that form part of a lightning protection system (LPS). Typically, these can be connectors, bonding and bridging components, expansion pieces and test joints. Testing of components for an explosive atmosphere is not covered by this standard. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC 60068-2-52:1996, Environmental testing – Part 2-52: Tests – Test Kb: Salt mist, cyclic (sodium chloride solution) IEC 62305-1, Protection against lightning – Part 1: General principles IEC 62561-2, Lightning protection system components (LPSC) – Part 2: Requirements for conductors and earth electrodes ISO 6957:1988, Copper alloys – Ammonia test for stress corrosion resistance ISO 6988:1985, Metallic and other non-organic coatings – Sulfur dioxide test with general condensation of moisture 3 Terms and definitions For the purpose of this document, the following terms and definitions apply. 3.1
connection component part of an external LPS which is used for the connection of conductors to each other or to metallic installations Note 1 to entry Connection component includes connectors, clamps, bridging component and expansion piece. 3.2
metal installa
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.