SIST EN ISO 24263:2021
(Main)Footwear - Attachment strength of straps, trims and accessories (ISO 24263:2020)
Footwear - Attachment strength of straps, trims and accessories (ISO 24263:2020)
This standard describes a method for determining the attachment strength of footwear upper straps joined to the sole, upper decorations, hooks, eyelets and trims.
Schuhe - Abzugsfestigkeit von Riemen, Zierstreifen und Zubehör (ISO 24263:2020)
Dieses Dokument legt ein Verfahren zur Bestimmung der Abzugsfestigkeit von an der Sohle befestigten Schuhriemen, Haken, Ösen und Zierstreifen fest.
Chaussures - Résistance de fixation des lanières, bandes et accessoires (ISO 24263:2020)
Le présent document spécifie une méthode de détermination de la résistance de fixation des lanières supérieures reliées à la semelle, des crochets, des œillets et des bandes présents sur les chaussures.
Obutev - Pritrdilna trdnost jermenov, trakov in dodatnih delov (ISO 24263:2020)
General Information
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 24263:2021
01-januar-2021
Obutev - Pritrdilna trdnost jermenov, trakov in dodatnih delov (ISO 24263:2020)
Footwear - Attachment strength of straps, trims and accessories (ISO 24263:2020)
Schuhe - Abzugsfestigkeit von Riemen, Zierstreifen und Zubehör (ISO 24263:2020)
Chaussures - Résistance de fixation des lanières, bandes et accessoires (ISO
24263:2020)
Ta slovenski standard je istoveten z: EN ISO 24263:2020
ICS:
61.060 Obuvala Footwear
SIST EN ISO 24263:2021 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 24263:2021
---------------------- Page: 2 ----------------------
SIST EN ISO 24263:2021
EN ISO 24263
EUROPEAN STANDARD
NORME EUROPÉENNE
November 2020
EUROPÄISCHE NORM
ICS 61.060
English Version
Footwear - Attachment strength of straps, trims and
accessories (ISO 24263:2020)
Chaussures - Résistance de fixation des lanières, Schuhe - Abzugsfestigkeit von Riemen, Zierstreifen und
bandes et accessoires (ISO 24263:2020) Zubehör (ISO 24263:2020)
This European Standard was approved by CEN on 31 August 2020.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2020 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 24263:2020 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 24263:2021
EN ISO 24263:2020 (E)
Contents Page
European foreword . 3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 24263:2021
EN ISO 24263:2020 (E)
European foreword
This document (EN ISO 24263:2020) has been prepared by Technical Committee ISO/TC 216
"Footwear" in collaboration with Technical Committee CEN/TC 309 “Footwear” the secretariat of which
is held by UNE.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by May 2021, and conflicting national standards shall be
withdrawn at the latest by May 2021.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
Endorsement notice
The text of ISO 24263:2020 has been approved by CEN as EN ISO 24263:2020 without any modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 24263:2021
---------------------- Page: 6 ----------------------
SIST EN ISO 24263:2021
INTERNATIONAL ISO
STANDARD 24263
First edition
2020-10
Footwear — Attachment strength of
straps, trims and accessories
Chaussures — Résistance de fixation des lanières, bandes et
accessoires
Reference number
ISO 24263:2020(E)
©
ISO 2020
---------------------- Page: 7 ----------------------
SIST EN ISO 24263:2021
ISO 24263:2020(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2020
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2020 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 24263:2021
ISO 24263:2020(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Apparatus . 1
5 Sampling and conditioning . 3
5.1 Attachment strength of straps . 3
5.2 Attachment strength of trims . 3
5.3 Attachment strength of hooks and eyelets . 3
6 Preparation of test-pieces . 3
6.1 Attachment strength of straps . 3
6.2 Attachment strength of trims . 3
6.3 Attachment strength of hooks and eyelets . 3
7 Procedure. 3
7.1 Attachment strength of straps . 3
7.2 Attachment strength of trims . 5
7.3 Attachment strength of hooks and eyelets . 5
8 Expression of results . 5
8.1 Attachment strength of straps . 5
8.2 Attachment strength of trims . 5
8.3 Attachment strength of hooks and eyelets . 5
9 Test report . 5
© ISO 2020 – All rights reserved iii
---------------------- Page: 9 ----------------------
SIST EN ISO 24263:2021
ISO 24263:2020(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body
...
SLOVENSKI STANDARD
oSIST prEN ISO 24263:2020
01-februar-2020
Obutev - Pritrdilna trdnost jermenov, trakov in dodatnih delov (ISO/DIS
24263:2019)
Footwear - Attachment strength of straps, trims and accessories (ISO/DIS 24263: 2019)
Schuhe - Abzugsfestigkeit von Riemen, Zierstreifen und Zubehör (ISO/DIS 24263:2019)
Chaussures - Résistance de fixation des lanières, bandes et accessoires (ISO/DIS
24263: 2019)
Ta slovenski standard je istoveten z: prEN ISO 24263
ICS:
61.060 Obuvala Footwear
oSIST prEN ISO 24263:2020 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN ISO 24263:2020
---------------------- Page: 2 ----------------------
oSIST prEN ISO 24263:2020
DRAFT INTERNATIONAL STANDARD
ISO/DIS 24263
ISO/TC 216 Secretariat: UNE
Voting begins on: Voting terminates on:
2019-10-21 2020-01-13
Footwear — Attachments strength of straps, trims and
accesories
ICS: 61.060
THIS DOCUMENT IS A DRAFT CIRCULATED
This document is circulated as received from the committee secretariat.
FOR COMMENT AND APPROVAL. IT IS
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS
ISO/CEN PARALLEL PROCESSING
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO/DIS 24263:2019(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
©
PROVIDE SUPPORTING DOCUMENTATION. ISO 2019
---------------------- Page: 3 ----------------------
oSIST prEN ISO 24263:2020
ISO/DIS 24263:2019(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2019
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2019 – All rights reserved
---------------------- Page: 4 ----------------------
oSIST prEN ISO 24263:2020
ISO/DIS 24263:2019(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Apparatus and materials. 1
4 Sampling and conditioning . 3
4.1 Method A — Tensile strength of straps . 3
4.2 Method B — Tensile strength of ornaments . 3
4.3 Method C — Tensile strength of hooks and eyelets . 3
5 Preparation of test-pieces . 3
5.1 Method A — Tensile strength of straps . 3
5.2 Method B — Tensile strength of ornaments . 3
5.3 Method C — Tensile strength of hooks and eyelets . 3
6 Procedure. 3
6.1 Method A — Tensile strength of straps . 3
6.2 Method B — Tensile strength of ornaments . 5
6.3 Method C — Tensile strength of hooks and eyelets . 5
7 Expression of results . 5
7.1 Method A — Tensile strength of straps . 5
7.2 Method B — Tensile strength of ornaments . 5
7.3 Method C — Tensile strength of hooks and eyelets . 5
8 Test report . 6
© ISO 2019 – All rights reserved iii
---------------------- Page: 5 ----------------------
oSIST prEN ISO 24263:2020
ISO/DIS 24263:2019(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/patents).
Any tr
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.