SIST EN 301 406-1 V3.1.1:2023

Digital Enhanced Cordless Telecommunications (DECT) - Harmonised Standard for access to radio spectrum - Part 1: DECT, DECT Evolution and DECT ULE

The present document specifies technical characteristics and methods of measurements for equipment implementing the
Digital Enhanced Cordless Telecommunications (DECT) common interface, as specified in the multi-part technical
specification ETSI EN 300 175 including the variants DECT Evolution and DECT ULE (see ETSI EN 300 175-1 [i.3]
for an overview).
The present document applies to the following equipment types:
a) Fixed Part (FP);
b) Portable Part (PP);
c) Cordless Terminal Adapter (CTA);
d) Wireless Relay Station (WRS) (FP and PP combined);
e) Hybrid Part (HyP) (a PP with capability to act as a FP to provide PP to PP communication).
These radio equipment types are capable of operating in all or any part of the frequency bands given in table 1.
The DECT service frequency band for transmitting and receiving for all elements is 1 880 MHz to 1 900 MHz.
Details of the DECT Common Interface may be found in ETSI EN 300 175-1 [i.3], ETSI EN 300 175 parts 2 [1] to
3 [2], ETSI EN 300 175-4 [i.4], ETSI EN 300 175 parts 5 [3] to 6 [4], and ETSI EN 300 175 parts 7 [i.5] to 8 [i.6].
Further details of the DECT system may be found in the ETSI TR 101 178 [i.1].
DECT ULE implements, in addition to the DECT Common Interface, the multi-part ETSI TS 102 939 (see ETSI TS 102 939-1 [i.7] and ETSI TS 102 939-2 [i.8]).
The present document contains requirements to demonstrate that radio equipment both effectively uses and supports the
efficient use of radio spectrum in order to avoid harmful interference.
NOTE: The relationship between the present document and essential requirements of article 3.2 of Directive 2014/53/EU [i.10] is given in annex A.

Digitalne izboljšane brezvrvične telekomunikacije (DECT) - Harmonizirani standard za dostop do radijskega spektra - 1. del: DECT, razvoj DECT in DECT ULE

Ta dokument določa tehnične lastnosti in metode merjenja za opremo, ki izvaja skupni vmesnik za digitalne izboljšane brezvrvične telekomunikacije (DECT), kot je navedeno v večdelni tehnični specifikaciji ETSI EN 300 175, vključno z razvojem DECT in DECT ULE (za pregled glej standard ETSI EN 300 175-1 [i.3]).
Ta dokument se uporablja za opremo naslednjih vrst:
a) fiksni del (FP);
b) prenosni del (PP);
c) brezvrvični terminalski prilagodilnik (CTA);
d) brezžična relejna postaja (WRS) (fiksni in prenosni del skupaj);
e) hibridni del (HyP) (prenosni del z zmožnostjo delovanja kot fiksni del za namen zagotovitve komunikacije med dvema prenosnima deloma).
Ti tipi radijske opreme lahko delujejo v vseh frekvenčnih pasovih iz preglednice 1 ali katerem koli njihovem delu.
Frekvenčni pas storitve za digitalne izboljšane brezvrvične telekomunikacije za oddajanje in sprejemanje za vse elemente je od 1880 MHz do 1900 MHz.
Podrobnosti skupnega vmesnika za digitalne izboljšane brezvrvične telekomunikacije so navedene v standardih ETSI EN 300 175-1 [i.3], ETSI EN 300 175 (2. del [1] in 3. del [2]), ETSI EN 300 175-4 [i.4], ETSI EN 300 175 (5. del [3] in 6. del [4]) ter ETSI EN 300 175 (7. del [i.5] in 8. del [i.6]).
Dodatne podrobnosti o sistemu digitalne izboljšane brezvrvične telekomunikacije so navedene v tehnični specifikaciji ETSI TR 101 178 [i.1].
Informacije o izvajanju DECT ULE poleg skupnega vmesnika za digitalne izboljšane brezvrvične telekomunikacije so navedene v večdelni tehnični specifikaciji ETSI TS 102 939 (glej dokumenta ETSI TS 102 939-1 [i.7] in ETSI TS 102 939-2 [i.8]).
Ta dokument vsebuje zahteve, s katerimi se dokazuje, da je radijska oprema izdelana tako, da učinkovito uporablja in podpira učinkovito rabo radijskega spektra z namenom preprečevanja škodljivih motenj.
OPOMBA: Razmerje med tem dokumentom in bistvenimi zahtevami člena 3.2 Direktive 2014/53/EU [i.10] je podano v dodatku A.

General Information

• Status: Published
• Public Enquiry End Date: 26-Oct-2022
• Publication Date: 22-Nov-2022
• ICS: 33.070.30 - Digital Enhanced Cordless Telecommunications (DECT)
• Technical Committee: MOC - Mobile Communications
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 21-Nov-2022
• Due Date: 26-Jan-2023
• Completion Date: 23-Nov-2022
• Ref Project: ETSI EN 301 406-1 V3.1.1 (2022-10) - Digital Enhanced Cordless Telecommunications (DECT); Harmonised Standard for access to radio spectrum; Part 1: DECT, DECT Evolution and DECT ULE

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 301 406-1 V3.1.1:2023
01-januar-2023
Digitalne izboljšane brezvrvične telekomunikacije (DECT) - Harmonizirani standard
za dostop do radijskega spektra - 1. del: DECT, razvoj DECT in DECT ULE
Digital Enhanced Cordless Telecommunications (DECT) - Harmonised Standard for
access to radio spectrum - Part 1: DECT, DECT Evolution and DECT ULE
Ta slovenski standard je istoveten z: ETSI EN 301 406-1 V3.1.1 (2022-10)
ICS:
33.070.30 Digitalne izboljšane Digital Enhanced Cordless
brezvrvične telekomunikacije Telecommunications (DECT)
(DECT)
SIST EN 301 406-1 V3.1.1:2023 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN 301 406-1 V3.1.1:2023

---------------------- Page: 2 ----------------------
SIST EN 301 406-1 V3.1.1:2023
ETSI EN 301 406-1 V3.1.1 (2022-10)






HARMONISED EUROPEAN STANDARD
Digital Enhanced Cordless Telecommunications (DECT);
Harmonised Standard for access to radio spectrum;
Part 1: DECT, DECT Evolution and DECT ULE

---------------------- Page: 3 ----------------------
SIST EN 301 406-1 V3.1.1:2023

2 ETSI EN 301 406-1 V3.1.1 (2022-10)

Reference
REN/DECT-00359-1
Keywords
DECT, digital, generic, radio, regulation, testing
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: [phone]  Fax: [phone]

Siret N° 348 623 562 00017 - APE 7112B
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° w061004871

Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI
deliverable is the one made publicly available in PDF format at www.etsi.org/deliver.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
If you find a security vulnerability in the present document, please report it through our
Coordinated Vulnerability Disclosure Program:
https://www.etsi.org/standards/coordinated-vulnerability-disclosure
Notice of disclaimer & limitation of liability
The information provided in the present deliverable is directed solely to professionals who have the appropriate degree of
experience to understand and interpret its content in accordance with generally accepted engineering or
other professional standard and applicable regulations.
No recommendation as to products and services or vendors is made or should be implied.
In no event shall ETSI be held liable for loss of profits or any other incidental or consequential damages.

Any software contained in this deliverable is provided "AS IS" with no warranties, express or implied, including but not
limited to, the warranties of merchantability, fitness for a particular purpose and non-infringement of intellectual property
rights and ETSI shall not be held liable in any event for any damages whatsoever (including, without limitation, damages
for loss of profits, business interruption, loss of information, or any other pecuniary loss) arising out of or related to the use
of or inability to use the software.
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and
microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.

© ETSI 2022.
All rights reserved.

ETSI

---------------------- Page: 4 ----------------------
SIST EN 301 406-1 V3.1.1:2023

3 ETSI EN 301 406-1 V3.1.1 (2022-10)
Contents
Intellectual Property Rights . 10
Foreword . 10
Modal verbs terminology . 11
1 Scope . 12
2 References . 12
2.1 Normative references . 12
2.2 Informative references . 13
3 Definition of terms, symbols and abbreviations . 14
3.1 Terms . 14
3.2 Symbols . 17
3.3 Abbreviations . 17
4 Technical requirements specifications . 18
4.1 Environmental profile . 18
4.2 Overview . 18
4.2.0 General . 18
4.2.1 Test suites . 18
4.2.2 Test groups. 18
4.2.3 Test cases . 19
4.3 Product information for testing . 19
4.3.1 Information on capabilities and options implemented . 19
4.3.2 Additional information on implementation for testing . 20
4.4 Applicability of tests . 20
4.4.0 Introduction. 20
4.4.1 Equipment that includes only a DECT RF receiver . 20
4.4.2 Equipment that includes a radio transmitter . 20
4.4.3 CTAs . 20
4.4.4 Equipment with combined FT and PT functionality . 20
4.4.4.0 General . 20
4.4.4.1 Wireless Relay Station . 21
4.4.4.2 Direct PP to PP communication . 21
4.4.4.3 Distributed Communications. 21
4.4.5 Equipment that is capable of using higher level modulation . 21
4.4.6 Equipment supporting additional carriers . 21
4.5 Conformance requirements . 21
4.5.1 Accuracy and stability of RF carriers . 21
4.5.1.1 Definition . 21
4.5.1.2 Limits . 22
4.5.1.3 Conformance . 22
4.5.2 Accuracy and stability of timing parameters . 22
4.5.2.0 General . 22
4.5.2.1 Definitions . 22
4.5.2.1.1 Slot structure . 22
4.5.2.1.2 Definition of the position of p0 . 22
4.5.2.2 Limits . 23
4.5.2.2.1 Reference timer accuracy and stability . 23
4.5.2.2.2 RFP transmission jitter . 23
4.5.2.2.3 PP reference timer synchronization . 23
4.5.2.3 Conformance . 24
4.5.3 Transmission burst . 24
4.5.3.1 Definitions . 24
4.5.3.1.0 Introduction . 24
4.5.3.1.1 Physical packets. 24
4.5.3.1.2 Transmitted power . 24
4.5.3.1.3 Normal Transmitted Power (NTP) . 24
ETSI

---------------------- Page: 5 ----------------------
SIST EN 301 406-1 V3.1.1:2023

4 ETSI EN 301 406-1 V3.1.1 (2022-10)
4.5.3.1.4 Transmitter attack time . 24
4.5.3.1.5 Transmitter release time . 24
4.5.3.1.6 Minimum power . 24
4.5.3.1.7 Maximum power . 25
4.5.3.1.8 Maintenance of transmission after packet end . 25
4.5.3.1.9 Transmitter idle power output . 25
4.5.3.2 Limits . 25
4.5.3.2.1 Transmitter attack time . 25
4.5.3.2.2 Transmitter release time . 25
4.5.3.2.3 Minimum power . 25
4.5.3.2.4 Maximum power . 25
4.5.3.2.5 Maintenance of transmission after packet end . 25
4.5.3.2.6 Transmitter idle power output . 25
4.5.3.3 Conformance . 25
4.5.4 Transmitted power . 26
4.5.4.1 Definitions . 26
4.5.4.1.0 Transceiver and P definitions . 26
NTP
4.5.4.1.1 PP and RFP with an integral antenna . 26
4.5.4.1.2 PP and RFP with external connections for all antennas . 26
4.5.4.1.3 PP and RFP with both integral and external antennas . 26
4.5.4.2 Limits . 26
4.5.4.3 Conformance . 27
4.5.4.4 Multi-transceiver systems . 27
4.5.5 RF carrier modulation . 27
4.5.5.1 Definition . 27
4.5.5.2 Limits . 27
4.5.5.3 Conformance . 27
4.5.6 Unwanted RF power radiation . 28
4.5.6.1 General . 28
4.5.6.2 Emissions due to modulation . 28
4.5.6.2.1 Definition. 28
4.5.6.2.2 Limits . 28
4.5.6.2.3 Conformance . 28
4.5.6.3 Emissions due to transmitter transients . 28
4.5.6.3.1 Definition. 28
4.5.6.3.2 Limits . 28
4.5.6.3.3 Conformance . 29
4.5.6.4 Emissions due to intermodulation . 29
4.5.6.4.1 Definition. 29
4.5.6.4.2 Limits . 29
4.5.6.4.3 Conformance . 29
4.5.6.5 Spurious emissions when allocated a transmit channel . 29
4.5.6.5.1 Definition. 29
4.5.6.5.2 Limits . 29
4.5.6.5.3 Conformance . 30
4.5.7 Radio receiver testing . 30
4.5.7.0 General . 30
4.5.7.1 Radio receiver sensitivity . 30
4.5.7.1.1 Definition. 30
4.5.7.1.2 Limits . 30
4.5.7.1.3 Conformance . 30
4.5.7.2 Radio receiver reference BER and FER . 30
4.5.7.2.1 Definition. 30
4.5.7.2.2 Limits . 30
4.5.7.2.3 Conformance . 30
4.5.7.3 Radio receiver interference performance . 31
4.5.7.3.1 Definition. 31
4.5.7.3.2 Limits . 31
4.5.7.3.3 Conformance . 31
4.5.7.4 Radio receiver blocking case 1: owing to signals occurring at the same time but on other
frequencies . 31
ETSI

---------------------- Page: 6 ----------------------
SIST EN 301 406-1 V3.1.1:2023

5 ETSI EN 301 406-1 V3.1.1 (2022-10)
4.5.7.4.1 Definition. 31
4.5.7.4.2 Limits . 31
4.5.7.4.3 Conformance . 32
4.5.7.5 Radio receiver blocking case 2: owing to signals occurring at a different time . 32
4.5.7.5.1 Definition. 32
4.5.7.5.2 Limits . 32
4.5.7.5.3 Conformance . 32
4.5.7.6 Receiver intermodulation performance . 32
4.5.7.6.1 Definition. 32
4.5.7.6.2 Limits . 32
4.5.7.6.3 Conformance . 32
4.5.7.7 Spurious emissions when the PP has no allocated transmit channel . 32
4.5.7.7.1 Definition. 32
4.5.7.7.2 Limits . 32
4.5.7.7.3 Conformance . 33
4.5.8 Channel access . 33
4.5.8.1 Channel selection . 33
4.5.8.2 Channel confirmation . 33
4.5.8.2.1 For the PT . 33
4.5.8.2.2 For the FT . 33
4.5.8.3 Channel release . 34
4.5.8.4 General . 34
4.5.8.5 Channel selection and confirmation for DECT ULE . 34
4.5.8.5.1 General . 34
4.5.8.5.2 For the PT . 34
4.5.8.5.3 For the FT . 34
4.5.9 WRS testing . 35
4.5.9.0 General requirements . 35
4.5.9.1 Testing as a PP . 35
4.5.9.2 Testing as an RFP . 35
4.5.9.3 Additional requirements . 36
4.5.9.4 Conformance . 39
4.5.10 Requirements for PPs with direct PP to PP communication mode . 39
4.5.10.1 General requirements . 39
4.5.10.2 Conformance . 39
4.5.11 Direct Communication . 39
4.5.11.0 General requirements . 39
4.5.11.1 Testing as a PP . 40
4.5.11.2 Testing as an RFP . 40
4.5.11.3 Conformance . 40
4.5.12 Higher level modulation options . 41
4.5.12.0 Requirements . 41
4.5.12.1 Conformance . 41
5 Testing for compliance with technical requirements . 42
5.1 General test requirements . 42
5.1.1 Test philosophy .
...

ETSI EN 301 406-1 V3.1.1 (2022-10)






HARMONISED EUROPEAN STANDARD
Digital Enhanced Cordless Telecommunications (DECT);
Harmonised Standard for access to radio spectrum;
Part 1: DECT, DECT Evolution and DECT ULE

---------------------- Page: 1 ----------------------
2 ETSI EN 301 406-1 V3.1.1 (2022-10)

Reference
REN/DECT-00359-1
Keywords
DECT, digital, generic, radio, regulation, testing
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: [phone]  Fax: [phone]

Siret N° 348 623 562 00017 - APE 7112B
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° w061004871

Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI
deliverable is the one made publicly available in PDF format at www.etsi.org/deliver.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
If you find a security vulnerability in the present document, please report it through our
Coordinated Vulnerability Disclosure Program:
https://www.etsi.org/standards/coordinated-vulnerability-disclosure
Notice of disclaimer & limitation of liability
The information provided in the present deliverable is directed solely to professionals who have the appropriate degree of
experience to understand and interpret its content in accordance with generally accepted engineering or
other professional standard and applicable regulations.
No recommendation as to products and services or vendors is made or should be implied.
In no event shall ETSI be held liable for loss of profits or any other incidental or consequential damages.

Any software contained in this deliverable is provided "AS IS" with no warranties, express or implied, including but not
limited to, the warranties of merchantability, fitness for a particular purpose and non-infringement of intellectual property
rights and ETSI shall not be held liable in any event for any damages whatsoever (including, without limitation, damages
for loss of profits, business interruption, loss of information, or any other pecuniary loss) arising out of or related to the use
of or inability to use the software.
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and
microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.

© ETSI 2022.
All rights reserved.

ETSI

---------------------- Page: 2 ----------------------
3 ETSI EN 301 406-1 V3.1.1 (2022-10)
Contents
Intellectual Property Rights . 10
Foreword . 10
Modal verbs terminology . 11
1 Scope . 12
2 References . 12
2.1 Normative references . 12
2.2 Informative references . 13
3 Definition of terms, symbols and abbreviations . 14
3.1 Terms . 14
3.2 Symbols . 17
3.3 Abbreviations . 17
4 Technical requirements specifications . 18
4.1 Environmental profile . 18
4.2 Overview . 18
4.2.0 General . 18
4.2.1 Test suites . 18
4.2.2 Test groups. 18
4.2.3 Test cases . 19
4.3 Product information for testing . 19
4.3.1 Information on capabilities and options implemented . 19
4.3.2 Additional information on implementation for testing . 20
4.4 Applicability of tests . 20
4.4.0 Introduction. 20
4.4.1 Equipment that includes only a DECT RF receiver . 20
4.4.2 Equipment that includes a radio transmitter . 20
4.4.3 CTAs . 20
4.4.4 Equipment with combined FT and PT functionality . 20
4.4.4.0 General . 20
4.4.4.1 Wireless Relay Station . 21
4.4.4.2 Direct PP to PP communication . 21
4.4.4.3 Distributed Communications. 21
4.4.5 Equipment that is capable of using higher level modulation . 21
4.4.6 Equipment supporting additional carriers . 21
4.5 Conformance requirements . 21
4.5.1 Accuracy and stability of RF carriers . 21
4.5.1.1 Definition . 21
4.5.1.2 Limits . 22
4.5.1.3 Conformance . 22
4.5.2 Accuracy and stability of timing parameters . 22
4.5.2.0 General . 22
4.5.2.1 Definitions . 22
4.5.2.1.1 Slot structure . 22
4.5.2.1.2 Definition of the position of p0 . 22
4.5.2.2 Limits . 23
4.5.2.2.1 Reference timer accuracy and stability . 23
4.5.2.2.2 RFP transmission jitter . 23
4.5.2.2.3 PP reference timer synchronization . 23
4.5.2.3 Conformance . 24
4.5.3 Transmission burst . 24
4.5.3.1 Definitions . 24
4.5.3.1.0 Introduction . 24
4.5.3.1.1 Physical packets. 24
4.5.3.1.2 Transmitted power . 24
4.5.3.1.3 Normal Transmitted Power (NTP) . 24
ETSI

---------------------- Page: 3 ----------------------
4 ETSI EN 301 406-1 V3.1.1 (2022-10)
4.5.3.1.4 Transmitter attack time . 24
4.5.3.1.5 Transmitter release time . 24
4.5.3.1.6 Minimum power . 24
4.5.3.1.7 Maximum power . 25
4.5.3.1.8 Maintenance of transmission after packet end . 25
4.5.3.1.9 Transmitter idle power output . 25
4.5.3.2 Limits . 25
4.5.3.2.1 Transmitter attack time . 25
4.5.3.2.2 Transmitter release time . 25
4.5.3.2.3 Minimum power . 25
4.5.3.2.4 Maximum power . 25
4.5.3.2.5 Maintenance of transmission after packet end . 25
4.5.3.2.6 Transmitter idle power output . 25
4.5.3.3 Conformance . 25
4.5.4 Transmitted power . 26
4.5.4.1 Definitions . 26
4.5.4.1.0 Transceiver and P definitions . 26
NTP
4.5.4.1.1 PP and RFP with an integral antenna . 26
4.5.4.1.2 PP and RFP with external connections for all antennas . 26
4.5.4.1.3 PP and RFP with both integral and external antennas . 26
4.5.4.2 Limits . 26
4.5.4.3 Conformance . 27
4.5.4.4 Multi-transceiver systems . 27
4.5.5 RF carrier modulation . 27
4.5.5.1 Definition . 27
4.5.5.2 Limits . 27
4.5.5.3 Conformance . 27
4.5.6 Unwanted RF power radiation . 28
4.5.6.1 General . 28
4.5.6.2 Emissions due to modulation . 28
4.5.6.2.1 Definition. 28
4.5.6.2.2 Limits . 28
4.5.6.2.3 Conformance . 28
4.5.6.3 Emissions due to transmitter transients . 28
4.5.6.3.1 Definition. 28
4.5.6.3.2 Limits . 28
4.5.6.3.3 Conformance . 29
4.5.6.4 Emissions due to intermodulation . 29
4.5.6.4.1 Definition. 29
4.5.6.4.2 Limits . 29
4.5.6.4.3 Conformance . 29
4.5.6.5 Spurious emissions when allocated a transmit channel . 29
4.5.6.5.1 Definition. 29
4.5.6.5.2 Limits . 29
4.5.6.5.3 Conformance . 30
4.5.7 Radio receiver testing . 30
4.5.7.0 General . 30
4.5.7.1 Radio receiver sensitivity . 30
4.5.7.1.1 Definition. 30
4.5.7.1.2 Limits . 30
4.5.7.1.3 Conformance . 30
4.5.7.2 Radio receiver reference BER and FER . 30
4.5.7.2.1 Definition. 30
4.5.7.2.2 Limits . 30
4.5.7.2.3 Conformance . 30
4.5.7.3 Radio receiver interference performance . 31
4.5.7.3.1 Definition. 31
4.5.7.3.2 Limits . 31
4.5.7.3.3 Conformance . 31
4.5.7.4 Radio receiver blocking case 1: owing to signals occurring at the same time but on other
frequencies . 31
ETSI

---------------------- Page: 4 ----------------------
5 ETSI EN 301 406-1 V3.1.1 (2022-10)
4.5.7.4.1 Definition. 31
4.5.7.4.2 Limits . 31
4.5.7.4.3 Conformance . 32
4.5.7.5 Radio receiver blocking case 2: owing to signals occurring at a different time . 32
4.5.7.5.1 Definition. 32
4.5.7.5.2 Limits . 32
4.5.7.5.3 Conformance . 32
4.5.7.6 Receiver intermodulation performance . 32
4.5.7.6.1 Definition. 32
4.5.7.6.2 Limits . 32
4.5.7.6.3 Conformance . 32
4.5.7.7 Spurious emissions when the PP has no allocated transmit channel . 32
4.5.7.7.1 Definition. 32
4.5.7.7.2 Limits . 32
4.5.7.7.3 Conformance . 33
4.5.8 Channel access . 33
4.5.8.1 Channel selection . 33
4.5.8.2 Channel confirmation . 33
4.5.8.2.1 For the PT . 33
4.5.8.2.2 For the FT . 33
4.5.8.3 Channel release . 34
4.5.8.4 General . 34
4.5.8.5 Channel selection and confirmation for DECT ULE . 34
4.5.8.5.1 General . 34
4.5.8.5.2 For the PT . 34
4.5.8.5.3 For the FT . 34
4.5.9 WRS testing . 35
4.5.9.0 General requirements . 35
4.5.9.1 Testing as a PP . 35
4.5.9.2 Testing as an RFP . 35
4.5.9.3 Additional requirements . 36
4.5.9.4 Conformance . 39
4.5.10 Requirements for PPs with direct PP to PP communication mode . 39
4.5.10.1 General requirements . 39
4.5.10.2 Conformance . 39
4.5.11 Direct Communication . 39
4.5.11.0 General requirements . 39
4.5.11.1 Testing as a PP . 40
4.5.11.2 Testing as an RFP . 40
4.5.11.3 Conformance . 40
4.5.12 Higher level modulation options . 41
4.5.12.0 Requirements . 41
4.5.12.1 Conformance . 41
5 Testing for compliance with technical requirements . 42
5.1 General test requirements . 42
5.1.1 Test philosophy . 42
5.1.2 Test site . 43
5.1.2.1 Open air test site . 43
5.1.2.1.1 Description . 43
5.1.2.1.2 Calibration . 43
5.1.2.2 Anechoic chamber . 44
5.1.2.2.1 General .
...

Draft ETSI EN 301 406-1 V2.3.0 (2022-07)






HARMONISED EUROPEAN STANDARD
Digital Enhanced Cordless Telecommunications (DECT);
Harmonised Standard for access to radio spectrum;
Part 1: DECT, DECT Evolution and DECT ULE

---------------------- Page: 1 ----------------------
2 Draft ETSI EN 301 406-1 V2.3.0 (2022-07)
Reference
REN/DECT-00359-1
Keywords
DECT, digital, generic, radio, regulation, testing

ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: [phone]  Fax: [phone]

Siret N° 348 623 562 00017 - APE 7112B
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° w061004871

Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI
deliverable is the one made publicly available in PDF format at www.etsi.org/deliver.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
If you find a security vulnerability in the present document, please report it through our
Coordinated Vulnerability Disclosure Program:
https://www.etsi.org/standards/coordinated-vulnerability-disclosure
Notice of disclaimer & limitation of liability
The information provided in the present deliverable is directed solely to professionals who have the appropriate degree of
experience to understand and interpret its content in accordance with generally accepted engineering or
other professional standard and applicable regulations.
No recommendation as to products and services or vendors is made or should be implied.
In no event shall ETSI be held liable for loss of profits or any other incidental or consequential damages.

Any software contained in this deliverable is provided "AS IS" with no warranties, express or implied, including but not
limited to, the warranties of merchantability, fitness for a particular purpose and non-infringement of intellectual property
rights and ETSI shall not be held liable in any event for any damages whatsoever (including, without limitation, damages
for loss of profits, business interruption, loss of information, or any other pecuniary loss) arising out of or related to the use
of or inability to use the software.
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and
microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.

© ETSI 2022.
All rights reserved.

ETSI

---------------------- Page: 2 ----------------------
3 Draft ETSI EN 301 406-1 V2.3.0 (2022-07)
Contents
Intellectual Property Rights . 10
Foreword . 10
Modal verbs terminology . 11
1 Scope . 12
2 References . 12
2.1 Normative references . 12
2.2 Informative references . 13
3 Definition of terms, symbols and abbreviations . 14
3.1 Terms . 14
3.2 Symbols . 17
3.3 Abbreviations . 17
4 Technical requirements specifications . 18
4.1 Environmental profile . 18
4.2 Overview . 18
4.2.0 General . 18
4.2.1 Test suites . 18
4.2.2 Test groups. 18
4.2.3 Test cases . 19
4.3 Product information for testing . 19
4.3.1 Information on capabilities and options implemented . 19
4.3.2 Additional information on implementation for testing . 20
4.4 Applicability of tests . 20
4.4.0 Introduction. 20
4.4.1 Equipment that includes only a DECT RF receiver . 20
4.4.2 Equipment that includes a radio transmitter . 20
4.4.3 CTAs . 20
4.4.4 Equipment with combined FT and PT functionality . 20
4.4.4.0 General . 20
4.4.4.1 Wireless Relay Station . 21
4.4.4.2 Direct PP to PP communication . 21
4.4.4.3 Distributed Communications. 21
4.4.5 Equipment that is capable of using higher level modulation . 21
4.4.6 Equipment supporting additional carriers . 21
4.5 Conformance requirements . 21
4.5.1 Accuracy and stability of RF carriers . 21
4.5.1.1 Definition . 21
4.5.1.2 Limits . 22
4.5.1.3 Conformance . 22
4.5.2 Accuracy and stability of timing parameters . 22
4.5.2.0 General . 22
4.5.2.1 Definitions . 22
4.5.2.1.1 Slot structure . 22
4.5.2.1.2 Definition of the position of p0 . 23
4.5.2.2 Limits . 23
4.5.2.2.1 Reference timer accuracy and stability . 23
4.5.2.2.2 RFP transmission jitter . 23
4.5.2.2.3 PP reference timer synchronization . 23
4.5.2.3 Conformance . 24
4.5.3 Transmission burst . 24
4.5.3.1 Definitions . 24
4.5.3.1.0 Introduction . 24
4.5.3.1.1 Physical packets. 24
4.5.3.1.2 Transmitted power . 24
ETSI

---------------------- Page: 3 ----------------------
4 Draft ETSI EN 301 406-1 V2.3.0 (2022-07)
4.5.3.1.3 Normal Transmitted Power (NTP) . 24
4.5.3.1.4 Transmitter attack time . 24
4.5.3.1.5 Transmitter release time . 25
4.5.3.1.6 Minimum power . 25
4.5.3.1.7 Maximum power . 25
4.5.3.1.8 Maintenance of transmission after packet end . 25
4.5.3.1.9 Transmitter idle power output . 25
4.5.3.2 Limits . 25
4.5.3.2.1 Transmitter attack time . 25
4.5.3.2.2 Transmitter release time . 25
4.5.3.2.3 Minimum power . 25
4.5.3.2.4 Maximum power . 25
4.5.3.2.5 Maintenance of transmission after packet end . 25
4.5.3.2.6 Transmitter idle power output . 26
4.5.3.3 Conformance . 26
4.5.4 Transmitted power . 26
4.5.4.1 Definitions . 26
4.5.4.1.0 Transceiver and P definitions . 26
NTP
4.5.4.1.1 PP and RFP with an integral antenna . 26
4.5.4.1.2 PP and RFP with external connections for all antennas . 26
4.5.4.1.3 PP and RFP with both integral and external antennas . 26
4.5.4.2 Limits . 27
4.5.4.3 Conformance . 27
4.5.4.4 Multi-transceiver systems . 27
4.5.5 RF carrier modulation . 27
4.5.5.1 Definition . 27
4.5.5.2 Limits . 27
4.5.5.3 Conformance . 28
4.5.6 Unwanted RF power radiation . 28
4.5.6.1 General . 28
4.5.6.2 Emissions due to modulation . 28
4.5.6.2.1 Definition. 28
4.5.6.2.2 Limits . 28
4.5.6.2.3 Conformance . 28
4.5.6.3 Emissions due to transmitter transients . 28
4.5.6.3.1 Definition. 28
4.5.6.3.2 Limits . 28
4.5.6.3.3 Conformance . 29
4.5.6.4 Emissions due to intermodulation . 29
4.5.6.4.1 Definition. 29
4.5.6.4.2 Limits . 29
4.5.6.4.3 Conformance . 29
4.5.6.5 Spurious emissions when allocated a transmit channel . 29
4.5.6.5.1 Definition. 29
4.5.6.5.2 Limits . 29
4.5.6.5.3 Conformance . 30
4.5.7 Radio receiver testing . 30
4.5.7.0 General . 30
4.5.7.1 Radio receiver sensitivity . 30
4.5.7.1.1 Definition. 30
4.5.7.1.2 Limits . 30
4.5.7.1.3 Conformance . 30
4.5.7.2 Radio receiver reference BER and FER . 30
4.5.7.2.1 Definition. 30
4.5.7.2.2 Limits . 31
4.5.7.2.3 Conformance . 31
4.5.7.3 Radio receiver interference performance . 31
4.5.7.3.1 Definition. 31
4.5.7.3.2 Limits . 31
4.5.7.3.3 Conformance . 31
ETSI

---------------------- Page: 4 ----------------------
5 Draft ETSI EN 301 406-1 V2.3.0 (2022-07)
4.5.7.4 Radio receiver blocking case 1: owing to signals occurring at the same time but on other
frequencies . 31
4.5.7.4.1 Definition. 31
4.5.7.4.2 Limits . 31
4.5.7.4.3 Conformance . 32
4.5.7.5 Radio receiver blocking case 2: owing to signals occurring at a different time . 32
4.5.7.5.1 Definition. 32
4.5.7.5.2 Limits . 32
4.5.7.5.3 Conformance . 32
4.5.7.6 Receiver intermodulation performance . 32
4.5.7.6.1 Definition. 32
4.5.7.6.2 Limits . 32
4.5.7.6.3 Conformance . 32
4.5.7.7 Spurious emissions when the PP has no allocated transmit channel . 32
4.5.7.7.1 Definition. 32
4.5.7.7.2 Limits . 33
4.5.7.7.3 Conformance . 33
4.5.8 Channel access . 33
4.5.8.1 Channel selection . 33
4.5.8.2 Channel confirmation . 33
4.5.8.2.1 For the PT . 33
4.5.8.2.2 For the FT . 33
4.5.8.3 Channel release . 34
4.5.8.4 General . 34
4.5.8.5 Channel selection and confirmation for DECT ULE . 34
4.5.8.5.1 General . 34
4.5.8.5.2 For the PT . 34
4.5.8.5.3 For the FT . 35
4.5.9 WRS testing . 35
4.5.9.0 General requirements . 35
4.5.9.1 Testing as a PP . 35
4.5.9.2 Testing as an RFP . 35
4.5.9.3 Additional requirements . 36
4.5.9.4 Conformance . 39
4.5.10 Requirements for PPs with direct PP to PP communication mode . 39
4.5.10.1 General requirements . 39
4.5.10.2 Conformance . 39
4.5.11 Direct Communication . 39
4.5.11.0 General requirements . 39
4.5.11.1 Testing as a PP . 40
4.5.11.2 Testing as an RFP . 40
4.5.11.3 Conformance . 40
4.5.12 Higher level modulation options . 40
4.5.12.0 Requirements . 40
4.5.12.1 Conformance . 41
5 Testing for compliance with technical requirements . 41
5.1 General test requirements . 41
5.1.1 Test philosophy . 41
5.1.2 Test site . 43
5.1.2.1 Open air test site . 43
5.1.2.1.1 Description . 43
5.1.2.1.2 Calibration . 43
5.1.2.2 Anechoic chamber . 44
5.1.2.2.1 General .
...

SLOVENSKI STANDARD
oSIST prEN 301 406-1 V2.3.0:2022
01-oktober-2022
Digitalne izboljšane brezvrvične telekomunikacije (DECT) - Harmonizirani standard
za dostop do radijskega spektra - 1. del: DECT, razvoj DECT in DECT ULE
Digital Enhanced Cordless Telecommunications (DECT) - Harmonised Standard for
access to radio spectrum - Part 1: DECT, DECT Evolution and DECT ULE
Ta slovenski standard je istoveten z: ETSI EN 301 406-1 V2.3.0 (2022-07)
ICS:
33.070.30 Digitalne izboljšane Digital Enhanced Cordless
brezvrvične telekomunikacije Telecommunications (DECT)
(DECT)
oSIST prEN 301 406-1 V2.3.0:2022 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN 301 406-1 V2.3.0:2022

---------------------- Page: 2 ----------------------
oSIST prEN 301 406-1 V2.3.0:2022
Draft ETSI EN 301 406-1 V2.3.0 (2022-07)






HARMONISED EUROPEAN STANDARD
Digital Enhanced Cordless Telecommunications (DECT);
Harmonised Standard for access to radio spectrum;
Part 1: DECT, DECT Evolution and DECT ULE

---------------------- Page: 3 ----------------------
oSIST prEN 301 406-1 V2.3.0:2022
 2 Draft ETSI EN 301 406-1 V2.3.0 (2022-07)
Reference
REN/DECT-00359-1
Keywords
DECT, digital, generic, radio, regulation, testing

ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: [phone]  Fax: [phone]

Siret N° 348 623 562 00017 - APE 7112B
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° w061004871

Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI
deliverable is the one made publicly available in PDF format at www.etsi.org/deliver.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
If you find a security vulnerability in the present document, please report it through our
Coordinated Vulnerability Disclosure Program:
https://www.etsi.org/standards/coordinated-vulnerability-disclosure
Notice of disclaimer & limitation of liability
The information provided in the present deliverable is directed solely to professionals who have the appropriate degree of
experience to understand and interpret its content in accordance with generally accepted engineering or
other professional standard and applicable regulations.
No recommendation as to products and services or vendors is made or should be implied.
In no event shall ETSI be held liable for loss of profits or any other incidental or consequential damages.

Any software contained in this deliverable is provided "AS IS" with no warranties, express or implied, including but not
limited to, the warranties of merchantability, fitness for a particular purpose and non-infringement of intellectual property
rights and ETSI shall not be held liable in any event for any damages whatsoever (including, without limitation, damages
for loss of profits, business interruption, loss of information, or any other pecuniary loss) arising out of or related to the use
of or inability to use the software.
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and
microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.

© ETSI 2022.
All rights reserved.

ETSI

---------------------- Page: 4 ----------------------
oSIST prEN 301 406-1 V2.3.0:2022
 3 Draft ETSI EN 301 406-1 V2.3.0 (2022-07)
Contents
Intellectual Property Rights . 10
Foreword . 10
Modal verbs terminology . 11
1 Scope . 12
2 References . 12
2.1 Normative references . 12
2.2 Informative references . 13
3 Definition of terms, symbols and abbreviations . 14
3.1 Terms . 14
3.2 Symbols . 17
3.3 Abbreviations . 17
4 Technical requirements specifications . 18
4.1 Environmental profile . 18
4.2 Overview . 18
4.2.0 General . 18
4.2.1 Test suites . 18
4.2.2 Test groups. 18
4.2.3 Test cases . 19
4.3 Product information for testing . 19
4.3.1 Information on capabilities and options implemented . 19
4.3.2 Additional information on implementation for testing . 20
4.4 Applicability of tests . 20
4.4.0 Introduction. 20
4.4.1 Equipment that includes only a DECT RF receiver . 20
4.4.2 Equipment that includes a radio transmitter . 20
4.4.3 CTAs . 20
4.4.4 Equipment with combined FT and PT functionality . 20
4.4.4.0 General . 20
4.4.4.1 Wireless Relay Station . 21
4.4.4.2 Direct PP to PP communication . 21
4.4.4.3 Distributed Communications. 21
4.4.5 Equipment that is capable of using higher level modulation . 21
4.4.6 Equipment supporting additional carriers . 21
4.5 Conformance requirements . 21
4.5.1 Accuracy and stability of RF carriers . 21
4.5.1.1 Definition . 21
4.5.1.2 Limits . 22
4.5.1.3 Conformance . 22
4.5.2 Accuracy and stability of timing parameters . 22
4.5.2.0 General . 22
4.5.2.1 Definitions . 22
4.5.2.1.1 Slot structure . 22
4.5.2.1.2 Definition of the position of p0 . 23
4.5.2.2 Limits . 23
4.5.2.2.1 Reference timer accuracy and stability . 23
4.5.2.2.2 RFP transmission jitter . 23
4.5.2.2.3 PP reference timer synchronization . 23
4.5.2.3 Conformance . 24
4.5.3 Transmission burst . 24
4.5.3.1 Definitions . 24
4.5.3.1.0 Introduction . 24
4.5.3.1.1 Physical packets. 24
4.5.3.1.2 Transmitted power . 24
ETSI

---------------------- Page: 5 ----------------------
oSIST prEN 301 406-1 V2.3.0:2022
 4 Draft ETSI EN 301 406-1 V2.3.0 (2022-07)
4.5.3.1.3 Normal Transmitted Power (NTP) . 24
4.5.3.1.4 Transmitter attack time . 24
4.5.3.1.5 Transmitter release time . 25
4.5.3.1.6 Minimum power . 25
4.5.3.1.7 Maximum power . 25
4.5.3.1.8 Maintenance of transmission after packet end . 25
4.5.3.1.9 Transmitter idle power output . 25
4.5.3.2 Limits . 25
4.5.3.2.1 Transmitter attack time . 25
4.5.3.2.2 Transmitter release time . 25
4.5.3.2.3 Minimum power . 25
4.5.3.2.4 Maximum power . 25
4.5.3.2.5 Maintenance of transmission after packet end . 25
4.5.3.2.6 Transmitter idle power output . 26
4.5.3.3 Conformance . 26
4.5.4 Transmitted power . 26
4.5.4.1 Definitions . 26
4.5.4.1.0 Transceiver and P definitions . 26
NTP
4.5.4.1.1 PP and RFP with an integral antenna . 26
4.5.4.1.2 PP and RFP with external connections for all antennas . 26
4.5.4.1.3 PP and RFP with both integral and external antennas . 26
4.5.4.2 Limits . 27
4.5.4.3 Conformance . 27
4.5.4.4 Multi-transceiver systems . 27
4.5.5 RF carrier modulation . 27
4.5.5.1 Definition . 27
4.5.5.2 Limits . 27
4.5.5.3 Conformance . 28
4.5.6 Unwanted RF power radiation . 28
4.5.6.1 General . 28
4.5.6.2 Emissions due to modulation . 28
4.5.6.2.1 Definition. 28
4.5.6.2.2 Limits . 28
4.5.6.2.3 Conformance . 28
4.5.6.3 Emissions due to transmitter transients . 28
4.5.6.3.1 Definition. 28
4.5.6.3.2 Limits . 28
4.5.6.3.3 Conformance . 29
4.5.6.4 Emissions due to intermodulation . 29
4.5.6.4.1 Definition. 29
4.5.6.4.2 Limits . 29
4.5.6.4.3 Conformance . 29
4.5.6.5 Spurious emissions when allocated a transmit channel . 29
4.5.6.5.1 Definition. 29
4.5.6.5.2 Limits . 29
4.5.6.5.3 Conformance . 30
4.5.7 Radio receiver testing . 30
4.5.7.0 General . 30
4.5.7.1 Radio receiver sensitivity . 30
4.5.7.1.1 Definition. 30
4.5.7.1.2 Limits . 30
4.5.7.1.3 Conformance . 30
4.5.7.2 Radio receiver reference BER and FER . 30
4.5.7.2.1 Definition. 30
4.5.7.2.2 Limits . 31
4.5.7.2.3 Conformance . 31
4.5.7.3 Radio receiver interference performance . 31
4.5.7.3.1 Definition. 31
4.5.7.3.2 Limits . 31
4.5.7.3.3 Conformance . 31
ETSI

---------------------- Page: 6 ----------------------
oSIST prEN 301 406-1 V2.3.0:2022
 5 Draft ETSI EN 301 406-1 V2.3.0 (2022-07)
4.5.7.4 Radio receiver blocking case 1: owing to signals occurring at the same time but on other
frequencies . 31
4.5.7.4.1 Definition. 31
4.5.7.4.2 Limits . 31
4.5.7.4.3 Conformance . 32
4.5.7.5 Radio receiver blocking case 2: owing to signals occurring at a different time . 32
4.5.7.5.1 Definition. 32
4.5.7.5.2 Limits . 32
4.5.7.5.3 Conformance . 32
4.5.7.6 Receiver intermodulation performance . 32
4.5.7.6.1 Definition. 32
4.5.7.6.2 Limits . 32
4.5.7.6.3 Conformance . 32
4.5.7.7 Spurious emissions when the PP has no allocated transmit channel . 32
4.5.7.7.1 Definition. 32
4.5.7.7.2 Limits . 33
4.5.7.7.3 Conformance . 33
4.5.8 Channel access . 33
4.5.8.1 Channel selection . 33
4.5.8.2 Channel confirmation . 33
4.5.8.2.1 For the PT . 33
4.5.8.2.2 For the FT . 33
4.5.8.3 Channel release . 34
4.5.8.4 General . 34
4.5.8.5 Channel selection and confirmation for DECT ULE . 34
4.5.8.5.1 General . 34
4.5.8.5.2 For the PT . 34
4.5.8.5.3 For the FT . 35
4.5.9 WRS testing . 35
4.5.9.0 General requirements . 35
4.5.9.1 Testing as a PP . 35
4.5.9.2 Testing as an RFP . 35
4.5.9.3 Additional requirements . 36
4.5.9.4 Conformance . 39
4.5.10 Requirements for PPs with direct PP to PP communication mode . 39
4.5.10.1 General requirements . 39
4.5.10.2 Conformance . 39
4.5.11 Direct Communication . 39
4.5.11.0 General requirements . 39
4.5.11.1 Testing as a PP . 40
4.5.11.2 Testing as an RFP . 40
4.5.11.3 Conformance . 40
4.5.12 Higher level modulation options . 40
4.5.12.0 Requirements . 40
4.5.12.1 Conformance . 41
5 Testing for compliance with technical requirements . 41
5.1 General test requirements . 41
5.1.1 Test philosophy .
...