SIST-TS CEN ISO/TS 12780-2:2008

Geometrical product specifications (GPS) - Straightness - Part 2: Specification operators (ISO/TS 12780-2:2003)

This part of ISO/TS 12780 specifies the complete specification operator for straightness of integral features only and covers complete straightness profiles only, i.e. geometrical characteristics of features of type line.
NOTE Straightness of an extracted median line of a cylinder is defined in ISO/TS 12180-1 and ISO/TS 12180-2.

Geometrische Produktspezifikation (GPS) - Geradheit - Teil 2: Spezifikationsoperatoren (ISO/TS 12780-2:2003)

Dieser Teil von ISO/TS 12780 legt den vollständigen Spezifikationsoperator für die Geradheit von vollständigen Geometrieelementen fest und betrifft nur vollständige Geradheitsprofile, d. h. geometrische Merkmale von Geometrieelementen der Art Gerade.
ANMERKUNG   Die Geradheit einer erfassten Mittellinie eines Zylinders ist in ISO/TS 12180 1 und ISO/TS 12180 2 angegeben.

Spécification géométrique des produits (GPS) - Rectitude - Partie 2: Opérateurs de spécification (ISO/TS 12780-2:2003)

L'ISO/TS 12780-2:2003 spécifie l'opérateur de spécification complet pour la rectitude des éléments intégraux et couvre uniquement les profils de rectitude complets, c'est-à-dire des caractéristiques géométriques des éléments de type ligne.

Specifikacija geometrijskih veličin izdelka - Premost - 2. del: Parametri za specifikacijo (ISO/TS 12780-2:2003)

General Information

• Status: Withdrawn
• Publication Date: 10-Mar-2008
• Withdrawal Date: 12-Sep-2011
• ICS: 17.040.40 - Geometrical Product Specification (GPS)
• Technical Committee: ISEL - Mechanical elements
• Current Stage: 9900 - Withdrawal (Adopted Project)
• Start Date: 09-Sep-2011
• Due Date: 02-Oct-2011
• Completion Date: 13-Sep-2011
• Ref Project: CEN ISO/TS 12780-2:2007 - Geometrical product specifications (GPS) - Straightness - Part 2: Specification operators (ISO/TS 12780-2:2003)

Relations

• Replaced By: SIST EN ISO 12780-2:2011 - Geometrical product specifications (GPS) - Straightness - Part 2: Specification operators (ISO 12780-2:2011)
• Effective Date: 01-Nov-2011
• Replaced By: SIST EN ISO 12780-2:2011 - Geometrical product specifications (GPS) - Straightness - Part 2: Specification operators (ISO 12780-2:2011)
• Effective Date: 08-Jun-2022

Standards Content (Sample)

SLOVENSKI STANDARD
SIST-TS CEN ISO/TS 12780-2:2008
01-april-2008
6SHFLILNDFLMDJHRPHWULMVNLKYHOLþLQL]GHOND3UHPRVWGHO3DUDPHWUL]D
VSHFLILNDFLMR,6276
Geometrical product specifications (GPS) - Straightness - Part 2: Specification operators
(ISO/TS 12780-2:2003)
Geometrische Produktspezifikation (GPS) - Geradheit - Teil 2: Spezifikationsoperatoren
(ISO/TS 12780-2:2003)
Spécification géométrique des produits (GPS) - Rectitude - Partie 2: Opérateurs de
spécification (ISO/TS 12780-2:2003)
Ta slovenski standard je istoveten z: CEN ISO/TS 12780-2:2007
ICS:
17.040.01 Linearne in kotne meritve na Linear and angular
splošno measurements in general
SIST-TS CEN ISO/TS 12780-2:2008 en,fr
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

TECHNICAL SPECIFICATION
CEN ISO/TS 12780-2
SPÉCIFICATION TECHNIQUE
TECHNISCHE SPEZIFIKATION
December 2007
ICS 17.040.01

English Version
Geometrical product specifications (GPS) - Straightness - Part
2: Specification operators (ISO/TS 12780-2:2003)
Spécification géométrique des produits (GPS) - Rectitude - Geometrische Produktspezifikation (GPS) - Geradheit - Teil
Partie 2: Opérateurs de spécification (ISO/TS 12780- 2: Spezifikationsoperatoren (ISO/TS 12780-2:2003)
2:2003)
This Technical Specification (CEN/TS) was approved by CEN on 8 October 2007 for provisional application.
The period of validity of this CEN/TS is limited initially to three years. After two years the members of CEN will be requested to submit their
comments, particularly on the question whether the CEN/TS can be converted into a European Standard.
CEN members are required to announce the existence of this CEN/TS in the same way as for an EN and to make the CEN/TS available
promptly at national level in an appropriate form. It is permissible to keep conflicting national standards in force (in parallel to the CEN/TS)
until the final decision about the possible conversion of the CEN/TS into an EN is reached.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2007 CEN All rights of exploitation in any form and by any means reserved Ref. No. CEN ISO/TS 12780-2:2007: E
worldwide for CEN national Members.

---------------------- Page: 2 ----------------------

CEN ISO/TS 12780-2:2007(E)
Contents Page
Foreword.3

2

---------------------- Page: 3 ----------------------

CEN ISO/TS 12780-2:2007(E)
Foreword
The text of ISO/TS 12780-2:2003 has been prepared by Technical Committee ISO/TC 213 "Dimensional and
geometrical product specifications and verification” of the International Organization for Standardization (ISO)
and has been taken over as CEN ISO/TS 12780-2:2007 by Technical Committee CEN/TC 290 “Dimensional
and geometrical product specification and verification” the secretariat of which is held by AFNOR.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to announce this Technical Specification: Austria, Belgium, Bulgaria, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of ISO/TS 12780-2:2003 has been approved by CEN as a CEN ISO/TS 12780-2:2007 without any
modification.

3

---------------------- Page: 4 ----------------------

TECHNICAL ISO/TS
SPECIFICATION 12780-2
First edition
2003-12-01

Geometrical Product Specifications
(GPS) — Straightness —
Part 2:
Specification operators
Spécification géométrique des produits (GPS) — Rectitude —
Partie 2: Opérateurs de spécification




Reference number
ISO/TS 12780-2:2003(E)
©
ISO 2003

---------------------- Page: 5 ----------------------

ISO/TS 12780-2:2003(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.


©  ISO 2003
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail [e-mail]
Web www.iso.org
Published in Switzerland

ii © ISO 2003 — All rights reserved

---------------------- Page: 6 ----------------------

ISO/TS 12780-2:2003(E)
Contents Page
Foreword. iv
Introduction . v
1 Scope. 1
2 Normative references. 1
3 Terms and definitions. 1
4 Complete specification operator . 1
5 Compliance with specification . 3
Annex A (informative) Harmonic content of nominally straight workpiece . 4
Annex B (informative) Relation to the GPS matrix model . 6
Bibliography . 8

© ISO 2003 — All rights reserved iii

---------------------- Page: 7 ----------------------

ISO/TS 12780-2:2003(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
In other circumstances, particularly when there is an urgent market requirement for such documents, a
technical committee may decide to publish other types of normative document:
 an ISO Publicly Available Specification (ISO/PAS) represents an agreement between technical experts in
an ISO working group and is accepted for publication if it is approved by more than 50 % of the members
of the parent committee casting a vote;
 an ISO Technical Specification (ISO/TS) represents an agreement between the members of a technical
committee and is accepted for publication if it is approved by 2/3 of the members of the committee casting
a vote.
An ISO/PAS or ISO/TS is reviewed after three years in order to decide whether it will be confirmed for a
further three years, revised to become an International Standard, or withdrawn. If the ISO/PAS or ISO/TS is
confirmed, it is reviewed again after a further three years, at which time it must either be transformed into an
International Standard or be withdrawn.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO/TS 12780-2 was prepared by Technical Committee ISO/TC 213, Dimensional and geometrical product
specifications and verification.
ISO/TS 12780 consists of the following parts, under the general title Geometrical Product Specifications
(GPS) — Straightness:
 Part 1: Vocabulary and parameters of straightness
 Part 2: Specification operators
iv © ISO 2003 — All rights reserved

---------------------- Page: 8 ----------------------

ISO/TS 12780-2:2003(E)
Introduction
This part of ISO/TS 12780 is a geometrical product specification (GPS) Technical Specification and is to be
regarded as a general GPS standard (see ISO/TR 14638). It influences chain link 3 of the chain of standards
on form of line independent of datum.
For more detailed information on the relation of this part of ISO/TS 12780 to other standards and the GPS
matrix model, see Annex B.
This part of ISO/TS 12780 specifies the specification operators according to ISO/TS 17450-2 for straightness
of integral features.
At the current state of development, ISO/TC 213 has not been able to reach a consensus on defaults for filter
cut-off, probe tip radius and method of association (reference line). This means that a straightness
specification must explicitly state which values are to be used for these specification operations in order for it
to be unique.
Consequently, if a specification does not explicitly state which values are to be used for one or more of these
operators, the specification is uncertain (see ISO/TS 17450-2) and a supplier can use any value for the
operator(s) not specified when proving conformance.
Extracting data will always involve applying a certain filtering process. An additional filtering of the extracted
data may or may not be applied. This additional filter can be a mean line filter (Gaussian, spline, wavelet, etc.)
or a non-linear filter (e.g. morphological filter). The type of filtering will influence the definition of straightness
and the specification operators and, therefore, needs to be stated unambiguously.
NOTE 1 Stylus filtering is not sufficient on its own to smooth a profile. In certain circumstances it can create spurious
high-frequency content, thus giving incorrect values. To correct this, a long
...