SIST EN 300 330-1 V1.8.1:2016
(Main)Electromagnetic compatibility and Radio spectrum Matters (ERM) - Short Range Devices (SRD) - Radio equipment in the frequency range 9 kHz to 25 MHz and inductive loop systems in the frequency range 9 kHz to 30 MHz - Part 1: Technical characteristics and test methods
Electromagnetic compatibility and Radio spectrum Matters (ERM) - Short Range Devices (SRD) - Radio equipment in the frequency range 9 kHz to 25 MHz and inductive loop systems in the frequency range 9 kHz to 30 MHz - Part 1: Technical characteristics and test methods
The present document applies to the following Short Range Device major equipment types:
1) Generic Short range Devices including transmitters operating in the range from 9 kHz to 25 MHz; and
2) inductive loop transmitters operating from 9 kHz to 30 MHz including Radio Frequency Identification (RFID)
and EAS operating in LF and HF ranges and for radio equipment including wireless power transfer (WPT)
function in the same frequency range;
3) receivers of systems as defined by bullets 1 and 2.
These radio equipment types are capable of operating in the permitted frequency bands within the 9 kHz to 30 MHz
range as specified in table 1:
• either with a Radio Frequency (RF) output connection and dedicated antenna or with an integral antenna;
• for all types of modulation;
• receivers of systems as defined by bullets 1 and 2.
Table 1 shows a list of the frequency bands as designated to Short Range Devices and the CEPT/ERC/REC 70-03 [i.1]
as known at the date of publication of the present document.
When selecting parameters for new SRDs, which may have inherent safety of human life implications, manufacturers
and users should pay particular attention to the potential for interference from other systems operating in the same or
adjacent bands.
The present document covers fixed stations, mobile stations and portable stations. If a system includes transponders,
these are measured together with the transmitter.
All types of modulation for radio devices are covered by the present document, provided the requirements of clause 7.3
are met.
The radio equipment, covered by the classification SRD is divided into several classes based on the maximum radiated
magnetic field strength. The field strength designation in the present document is based on CEPT/ERC/REC 70-03 [i.1]
and National SRD-frequency designations.
Three types of measuring methods are defined in the present document due to the varied nature of the antenna types for
equipment used in this band. One method measures the RF carrier current, another measures the radiated H-field and
the third conducted power.
The present document covers requirements for radiated emissions below as well as above 30 MHz.
Additional standards or specifications may be required for equipment such as that intended for connection to the
Public Switched Telephone Network (PSTN).
Elektromagnetna združljivost in zadeve v zvezi z radijskim spektrom (ERM) - Naprave kratkega dosega (SRD) - Radijska oprema v frekvenčnem območju od 9 kHz do 25 MHz in sistemi z indukcijsko zanko v frekvenčnem območju od 9 kHz do 30 MHz - 1. del: Tehnične karakteristike in preskusne metode
Ta dokument se uporablja za naslednje vrste glavne opreme naprav kratkega dosega:
1) generične naprave kratkega dosega, vključno z oddajniki za uporabo v območju od 9 kHz do 25 MHz; ter
2) oddajnike z indukcijsko zanko za uporabo v območju od 9 kHz do 30 MHz, vključno z radiofrekvenčno identifikacijo (RFID) in elektronskim nadzorom blaga (EAS), ki deluje v območjih nizke in visoke frekvence, ter za radijsko opremo, vključno s funkcijo brezžičnega prenosa energije (WPT) v istem frekvenčnem območju;
3) sprejemnike za sisteme iz 1. in 2. točke.
Te vrste radijske opreme lahko delujejo v dovoljenih frekvenčnih pasovih v razponu od 9 kHz do 30 MHz iz preglednice 1:
• z radiofrekvenčno (RF) izhodno povezavo in ustrezno anteno ali z vgrajeno anteno;
• za vse vrste modulacije;
• sprejemniki za sisteme iz 1. in 2. točke.
V preglednici 1 je prikazan seznam frekvenčnih pasov, kot so dodeljeni napravam kratkega dosega in opredeljeni v priporočilu CEPT/ERC/REC 70-03 [i.1], znanem na datum objave tega dokumenta.
Pri izbiranju parametrov za nove naprave kratkega dosega, ki lahko vplivajo na varnost človeškega življenja, naj bi bili proizvajalci in uporabniki predvsem pozorni na možnost motenj iz drugih sistemov, ki delujejo v istih ali bližnjih pasovih.
Ta dokument zajema stalne, mobilne in prenosne postaje. Če sistem vključuje transponderje, se ti izmerijo skupaj z oddajnikom.
Ta dokument pokriva vse vrste modulacije za radijske naprave, če so izpolnjeni pogoji iz člena 7.3.
Radijska oprema, ki jo pokriva klasifikacija naprav kratkega dosega, je razdeljena v več razredov na podlagi maksimalne izsevane jakosti magnetnega polja. Označevanje jakosti polja v tem dokumentu temelji na priporočilih CEPT/ERC/REC 70-03 [i.1]
in državnih označevanjih frekvence naprav kratkega dosega. V tem dokumentu so zaradi različnih vrst anten za opremo, ki se uporablja v tem pasu, določene tri vrste merilnih metod. Ena od metod meri tok RF nosilca, druga meri izsevano magnetno polje in tretja meri prevajano energijo.
Ta dokument zajema zahteve za elektromagnetno sevanje pod in tudi nad 30 MHz. Za opremo, kot je takšna, ki je namenjena za vzpostavljanje povezave z omrežjem PSTN, se lahko zahtevajo dodatni standardi ali specifikacije.
General Information
Buy Standard
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Electromagnetic compatibility and Radio spectrum Matters (ERM) - Short Range Devices (SRD) - Radio equipment in the frequency range 9 kHz to 25 MHz and inductive loop systems in the frequency range 9 kHz to 30 MHz - Part 1: Technical characteristics and test methods33.100.01Elektromagnetna združljivost na splošnoElectromagnetic compatibility in general33.060.20Sprejemna in oddajna opremaReceiving and transmitting equipmentICS:Ta slovenski standard je istoveten z:EN 300 330-1 V 1.8.1SIST EN 300 330-1 V1.8.1:2016en01-marec-2016SIST EN 300 330-1 V1.8.1:2016SLOVENSKI
STANDARD
SIST EN 300 330-1 V1.8.1:2016
ETSI EN 300 330-1 V1.8.1 (2015-03) Electromagnetic compatibility and Radio spectrum Matters (ERM); Short Range Devices (SRD); Radio equipment in the frequency range 9 kHz to 25 MHz and inductive loop systems in the frequency range 9 kHz to 30 MHz; Part 1: Technical characteristics and test methods
EUROPEAN STANDARD SIST EN 300 330-1 V1.8.1:2016
ETSI ETSI EN 300 330-1 V1.8.1 (2015-03) 2
Reference REN/ERM-TG28-0436 Keywords radio, RFID, SRD, testing ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00
Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C Association à but non lucratif enregistrée à la Sous-Préfecture de Grasse (06) N° 7803/88
Important notice The present document can be downloaded from: http://www.etsi.org/standards-search The present document may be made available in electronic versions and/or in print. The content of any electronic and/or print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at http://portal.etsi.org/tb/status/status.asp If you find errors in the present document, please send your comment to one of the following services: https://portal.etsi.org/People/CommiteeSupportStaff.aspx Copyright Notification No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm except as authorized by written permission of ETSI. The content of the PDF version shall not be modified without the written authorization of ETSI. The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2015. All rights reserved.
DECTTM, PLUGTESTSTM, UMTSTM and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members. 3GPPTM and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association. SIST EN 300 330-1 V1.8.1:2016
ETSI ETSI EN 300 330-1 V1.8.1 (2015-03) 3 Contents Intellectual Property Rights . 7 Foreword . 7 Modal verbs terminology . 7 Introduction . 8 1 Scope . 9 2 References . 10 2.1 Normative references . 10 2.2 Informative references . 11 3 Definitions, symbols and abbreviations . 12 3.1 Definitions . 12 3.2 Symbols . 13 3.3 Abbreviations . 14 4 Technical requirements specifications . 15 4.1 General requirements . 15 4.1.1 Receiver categorization . 15 4.1.2 General performance criteria . 15 4.1.3 General performance criteria for wireless power transfer (WPT) systems . 15 4.2 Presentation of equipment for testing purposes . 17 4.2.1 Choice of model for testing . 17 4.2.2 Testing of equipment with alternative radiated H-field strengths . 18 4.2.3 Testing of equipment that does not have an external 50 Ω RF connector (integral antenna equipment) . 18 4.2.3.1 Equipment with an internal permanent or temporary antenna connector . 18 4.2.3.2 Equipment with a temporary antenna connector . 18 4.2.3.3 Wireless Power Transfer systems . 18 4.2.4 On-site testing . 18 4.3 Mechanical and electrical design . 18 4.3.1 General . 18 4.3.1.1 WPT . 18 4.3.2 Controls . 18 4.3.3 Transmitter shut-off facility . 19 4.3.4 Receiver mute or squelch . 19 4.3.5 Marking (equipment identification) . 19 4.3.5.1 Equipment identification . 19 4.3.5.2 Equipment marking . 19 4.4 Declarations by the provider . 19 4.5 Auxiliary test equipment . 19 4.6 Interpretation of the measurement results . 19 5 Test conditions, power sources and ambient temperatures . 20 5.1 Normal and extreme test conditions . 20 5.2 Test power source . 20 5.2.1 External test power source . 20 5.2.2 Internal test power source . 20 5.3 Normal test conditions . 20 5.3.1 Normal temperature and humidity . 20 5.3.2 Normal test power source . 21 5.3.2.1 Mains voltage . 21 5.3.2.2 Regulated lead-acid battery power sources . 21 5.3.2.3 Other power sources . 21 5.4 Extreme test conditions . 21 5.4.1 Extreme temperatures . 21 5.4.1.1 Procedure for tests at extreme temperatures . 21 5.4.1.1.1 Procedure for equipment designed for continuous operation . 21 5.4.1.1.2 Procedure for equipment designed for intermittent operation . 21 SIST EN 300 330-1 V1.8.1:2016
ETSI ETSI EN 300 330-1 V1.8.1 (2015-03) 4 5.4.1.2 Extreme temperature ranges . 22 5.4.2 Extreme test source voltages . 22 5.4.2.1 Mains voltage . 22 5.4.2.2 Regulated lead-acid battery power sources . 22 5.4.2.3 Power sources using other types of batteries . 22 5.4.2.4 Other power sources . 23 6 General conditions . 23 6.1 Normal test signals and test modulation . 23 6.1.1 Normal test signals for analogue speech . 23 6.1.2 Normal test signals for data . 23 6.2 Artificial antenna . 23 6.2.1 Artificial antenna for inductive transmitters (non 50 Ω) . 23 6.2.2 Artificial antenna for transmitters with 50 Ω impedance connector . 24 6.3 Test fixture . 24 6.4 Test sites and general arrangements for radiated measurements . 25 6.5 Modes of operation of the transmitter . 25 6.6 Measuring receiver . 25 7 Transmitter requirements . 25 7.1 Transmitter definitions . 26 7.1.1 The inductive loop coil transmitters . 26 7.1.2 The large size loop transmitters . 26 7.1.3 Other transmitters . 26 7.1.4 Product Classes . 26 7.2 Transmitter carrier output levels . 30 7.2.1 H-field (radiated) . 30 7.2.1.1 Definition . 30 7.2.1.2 Methods of measurement . 30 7.2.1.3 Limits . 30 7.2.2 RF carrier current (Product Class 3 only) . 32 7.2.2.1 Definition . 32 7.2.2.2 Methods of measurement . 32 7.2.2.3 Limits . 32 7.2.3 Radiated E-field (Product Class 4 only) . 32 7.2.3.1 Definition . 32 7.2.3.2 Methods of measurement . 32 7.2.3.3 Limits . 33 7.3 Permitted range of operating frequencies . 33 7.3.1 Definition . 33 7.3.2 Method of measurement . 33 7.3.3 Limits . 33 7.4 Permitted frequency range of the modulation bandwidth . 33 7.4.1 Definition . 34 7.4.2 Method of measurement . 34 7.4.3 Limits . 34 7.5 Spurious domain emission limits . 35 7.5.1 Definition . 35 7.5.2 Conducted spurious emissions (Product class 3 only) . 35 7.5.2.1 Methods of measurement (< 30 MHz) . 35 7.5.2.2 Limits . 35 7.5.2.3 Methods of measurement (≥ 30 MHz) . 35 7.5.2.4 Limits . 36 7.5.3 Radiated field strength . 36 7.5.3.1 Methods of measurement (< 30 MHz) . 36 7.5.3.2 Limits . 36 7.5.4 Effective radiated power . 36 7.5.4.1 Methods of measurement (≥ 30 MHz) . 37 7.5.4.2 Limits . 37 8 Receiver requirement . 38 8.1 Adjacent channel selectivity - in band . 38 8.1.1 Definition . 38 SIST EN 300 330-1 V1.8.1:2016
ETSI ETSI EN 300 330-1 V1.8.1 (2015-03) 5 8.1.2 Method of measurement . 38 8.1.3 Limits . 39 8.2 Blocking or desensitization (Receiver category 1 and 2 only) . 39 8.2.1 Definition . 39 8.2.2 Methods of measurement . 39 8.2.3 Limits . 40 8.3 Receiver spurious radiation . 40 8.3.1 Definition . 41 8.3.2 Methods of measurement . 41 8.3.3 Limits . 41 8.3.3.1 Radiated emissions below 30 MHz . 41 8.3.3.2 Radiated emissions above 30 MHz . 41 9 Measurement uncertainty . 41 10 Interpretation of results . 42 10.1 Measurement uncertainty is equal to or less than maximum acceptable uncertainty . 42 Annex A (normative): Radiated measurement . 43 A.1 Test sites and general arrangements for measurements involving the use of radiated fields . 43 A.1.1 Anechoic chamber . 43 A.1.2 Anechoic chamber with a conductive ground plane . 44 A.1.3 Open Area Test Site (OATS) . 45 A.1.3.1 Measurements below 30 MHz . 46 A.1.3.2 Measurements above 30 MHz . 46 A.1.4 Test antenna . 47 A.1.5 Substitution antenna . 48 A.1.6 Measuring antenna . 48 A.2 Guidance on the use of radiation test sites . 48 A.2.1 Verification of the test site . 48 A.2.2 Preparation of the EUT . 48 A.2.3 Power supplies to the EUT . 48 A.2.4 Range length . 49 A.2.4.1 Far-field length above 30 MHz . 49 A.2.4.2 Near-field and Far-field length below 30 MHz . 49 A.2.5 Site preparation . 50 A.3 Coupling of signals . 50 A.3.1 General . 50 A.3.2 Data signals . 50 A.4 Standard test position . 50 A.5 Test fixture . 51 A.5.1 Description . 51 A.5.2 Calibration . 52 A.5.3 Mode of use . 52 A.6 Technical performance of the spectrum analyser . 53 Annex B (normative): H-field limit correction factor for generated E-fields . 54 Annex C (normative): Customized loop antennas . 55 C.1 Product classes related to the antenna loop . 55 C.1.1 Antenna loops below 1 MHz . 55 C.1.2 Antenna loops above 1 MHz . 56 Annex D (informative): Test fixture for measuring inductive transmitter carrier and harmonic currents by use of an artificial antenna (Product Class 3 only) . 58 Annex E (informative): E-fields in the near field at low frequencies . 60 SIST EN 300 330-1 V1.8.1:2016
ETSI ETSI EN 300 330-1 V1.8.1 (2015-03) 6 Annex F (normative): H-field measurements and limits at 3 m and 30 m . 61 F.1 Limits for measurements at 30 m distance . 61 F.2 Limits for measurements at 3 m distance . 62 Annex G (normative): Transmitter emission levels and spectrum mask measurements . 63 Annex H (normative): Generic inductive loop limits in the frequency range 148,5 kHz to 30 MHz . 66 H.1 Introduction . 66 H.2 Radiated H-field strength .
...
ETSI EN 300 330-1 V1.8.1 (2015-03)
EUROPEAN STANDARD
Electromagnetic compatibility
and Radio spectrum Matters (ERM);
Short Range Devices (SRD);
Radio equipment in the frequency range
9 kHz to 25 MHz and inductive loop systems
in the frequency range 9 kHz to 30 MHz;
Part 1: Technical characteristics and test methods
---------------------- Page: 1 ----------------------
2 ETSI EN 300 330-1 V1.8.1 (2015-03)
Reference
REN/ERM-TG28-0436
Keywords
radio, RFID, SRD, testing
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2015.
All rights reserved.
TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.
TM
3GPP and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI
---------------------- Page: 2 ----------------------
3 ETSI EN 300 330-1 V1.8.1 (2015-03)
Contents
Intellectual Property Rights . 7
Foreword . 7
Modal verbs terminology . 7
Introduction . 8
1 Scope . 9
2 References . 10
2.1 Normative references . 10
2.2 Informative references . 11
3 Definitions, symbols and abbreviations . 12
3.1 Definitions . 12
3.2 Symbols . 13
3.3 Abbreviations . 14
4 Technical requirements specifications . 15
4.1 General requirements . 15
4.1.1 Receiver categorization . 15
4.1.2 General performance criteria . 15
4.1.3 General performance criteria for wireless power transfer (WPT) systems . 15
4.2 Presentation of equipment for testing purposes . 17
4.2.1 Choice of model for testing . 17
4.2.2 Testing of equipment with alternative radiated H-field strengths . 18
4.2.3 Testing of equipment that does not have an external 50 Ω RF connector (integral antenna
equipment) . 18
4.2.3.1 Equipment with an internal permanent or temporary antenna connector . 18
4.2.3.2 Equipment with a temporary antenna connector . 18
4.2.3.3 Wireless Power Transfer systems . 18
4.2.4 On-site testing . 18
4.3 Mechanical and electrical design . 18
4.3.1 General . 18
4.3.1.1 WPT . 18
4.3.2 Controls . 18
4.3.3 Transmitter shut-off facility . 19
4.3.4 Receiver mute or squelch . 19
4.3.5 Marking (equipment identification) . 19
4.3.5.1 Equipment identification . 19
4.3.5.2 Equipment marking . 19
4.4 Declarations by the provider . 19
4.5 Auxiliary test equipment . 19
4.6 Interpretation of the measurement results . 19
5 Test conditions, power sources and ambient temperatures . 20
5.1 Normal and extreme test conditions . 20
5.2 Test power source . 20
5.2.1 External test power source . 20
5.2.2 Internal test power source . 20
5.3 Normal test conditions . 20
5.3.1 Normal temperature and humidity . 20
5.3.2 Normal test power source . 21
5.3.2.1 Mains voltage . 21
5.3.2.2 Regulated lead-acid battery power sources . 21
5.3.2.3 Other power sources . 21
5.4 Extreme test conditions . 21
5.4.1 Extreme temperatures . 21
5.4.1.1 Procedure for tests at extreme temperatures . 21
5.4.1.1.1 Procedure for equipment designed for continuous operation . 21
5.4.1.1.2 Procedure for equipment designed for intermittent operation . 21
ETSI
---------------------- Page: 3 ----------------------
4 ETSI EN 300 330-1 V1.8.1 (2015-03)
5.4.1.2 Extreme temperature ranges . 22
5.4.2 Extreme test source voltages . 22
5.4.2.1 Mains voltage . 22
5.4.2.2 Regulated lead-acid battery power sources . 22
5.4.2.3 Power sources using other types of batteries . 22
5.4.2.4 Other power sources . 23
6 General conditions . 23
6.1 Normal test signals and test modulation . 23
6.1.1 Normal test signals for analogue speech . 23
6.1.2 Normal test signals for data . 23
6.2 Artificial antenna . 23
6.2.1 Artificial antenna for inductive transmitters (non 50 Ω) . 23
6.2.2 Artificial antenna for transmitters with 50 Ω impedance connector . 24
6.3 Test fixture . 24
6.4 Test sites and general arrangements for radiated measurements . 25
6.5 Modes of operation of the transmitter . 25
6.6 Measuring receiver . 25
7 Transmitter requirements . 25
7.1 Transmitter definitions . 26
7.1.1 The inductive loop coil transmitters . 26
7.1.2 The large size loop transmitters . 26
7.1.3 Other transmitters . 26
7.1.4 Product Classes . 26
7.2 Transmitter carrier output levels . 30
7.2.1 H-field (radiated) . 30
7.2.1.1 Definition . 30
7.2.1.2 Methods of measurement . 30
7.2.1.3 Limits . 30
7.2.2 RF carrier current (Product Class 3 only) . 32
7.2.2.1 Definition . 32
7.2.2.2 Methods of measurement . 32
7.2.2.3 Limits . 32
7.2.3 Radiated E-field (Product Class 4 only) . 32
7.2.3.1 Definition . 32
7.2.3.2 Methods of measurement . 32
7.2.3.3 Limits . 33
7.3 Permitted range of operating frequencies . 33
7.3.1 Definition . 33
7.3.2 Method of measurement . 33
7.3.3 Limits . 33
7.4 Permitted frequency range of the modulation bandwidth . 33
7.4.1 Definition . 34
7.4.2 Method of measurement . 34
7.4.3 Limits . 34
7.5 Spurious domain emission limits . 35
7.5.1 Definition . 35
7.5.2 Conducted spurious emissions (Product class 3 only) . 35
7.5.2.1 Methods of measurement (< 30 MHz) . 35
7.5.2.2 Limits . 35
7.5.2.3 Methods of measurement (≥ 30 MHz) . 35
7.5.2.4 Limits . 36
7.5.3 Radiated field strength . 36
7.5.3.1 Methods of measurement (< 30 MHz) . 36
7.5.3.2 Limits . 36
7.5.4 Effective radiated power . 36
7.5.4.1 Methods of measurement (≥ 30 MHz) . 37
7.5.4.2 Limits . 37
8 Receiver requirement . 38
8.1 Adjacent channel selectivity - in band . 38
8.1.1 Definition . 38
ETSI
---------------------- Page: 4 ----------------------
5 ETSI EN 300 330-1 V1.8.1 (2015-03)
8.1.2 Method of measurement . 38
8.1.3 Limits . 39
8.2 Blocking or desensitization (Receiver category 1 and 2 only) . 39
8.2.1 Definition . 39
8.2.2 Methods of measurement . 39
8.2.3 Limits . 40
8.3 Receiver spurious radiation . 40
8.3.1 Definition . 41
8.3.2 Methods of measurement . 41
8.3.3 Limits . 41
8.3.3.1 Radiated emissions below 30 MHz . 41
8.3.3.2 Radiated emissions above 30 MHz . 41
9 Measurement uncertainty . 41
10 Interpretation of results . 42
10.1 Measurement uncertainty is equal to or less than maximum acceptable uncertainty . 42
Annex A (normative): Radiated measurement . 43
A.1 Test sites and general arrangements for measurements involving the use of radiated fields . 43
A.1.1 Anechoic chamber . 43
A.1.2 Anechoic chamber with a conductive ground plane . 44
A.1.3 Open Area Test Site (OATS) . 45
A.1.3.1 Measurements below 30 MHz . 46
A.1.3.2 Measurements above 30 MHz . 46
A.1.4 Test antenna . 47
A.1.5 Substitution antenna . 48
A.1.6 Measuring antenna . 48
A.2 Guidance on the use of radiation test sites . 48
A.2.1 Verification of the test site . 48
A.2.2 Preparation of the EUT . 48
A.2.3 Power supplies to the EUT . 48
A.2.4 Range length . 49
A.2.4.1 Far-field length above 30 MHz . 49
A.2.4.2 Near-field and Far-field length below 30 MHz . 49
A.2.5 Site preparation . 50
A.3 Coupling of signals . 50
A.3.1 General . 50
A.3.2 Data signals . 50
A.4 Standard test position . 50
A.5 Test fixture . 51
A.5.1 Description . 51
A.5.2 Calibration . 52
A.5.3 Mode of use . 52
A.6 Technical performance of the spectrum analyser . 53
Annex B (normative): H-field limit correction factor for generated E-fields . 54
Annex C (normative): Customized loop antennas . 55
C.1 Product classes related to the antenna loop . 55
C.1.1 Antenna loops below 1 MHz . 55
C.1.2 Antenna loops above 1 MHz . 56
Annex D (informative): Test fixture for measuring inductive transmitter carrier and
harmonic currents by use of an artificial antenna (Product Class 3
only) . 58
Annex E (informative): E-fields in the near field at low frequencies . 60
ETSI
---------------------- Page: 5 ----------------------
6 ETSI EN 300 330-1 V1.8.1 (2015-03)
Annex F (normative): H-field measurements and limits at 3 m and 30 m . 61
F.1 Limits for measurements at 30 m distance . 61
F.2 Limits for measurements at 3 m distance . 62
Annex G (normative): Transmitter emission levels and spectrum mask measurements . 63
Annex H (normative): Generic inductive loop limits in the frequency range
148,5 kHz to 30 MHz . 66
H.1 Introduction . 66
H.2 Radiated H-field strength . 66
H.2.1 Methods of measurements . 66
H.2.2 Radiated H-field strength limit .
...
Final draft ETSI EN 300 330-1 V1.8.1 (2014-12)
EUROPEAN STANDARD
Electromagnetic compatibility
and Radio spectrum Matters (ERM);
Short Range Devices (SRD);
Radio equipment in the frequency range
9 kHz to 25 MHz and inductive loop systems
in the frequency range 9 kHz to 30 MHz;
Part 1: Technical characteristics and test methods
---------------------- Page: 1 ----------------------
2 Final draft ETSI EN 300 330-1 V1.8.1 (2014-12)
Reference
REN/ERM-TG28-0436
Keywords
radio, RFID, SRD, testing
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
http://portal.etsi.org/chaircor/ETSI_support.asp
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2014.
All rights reserved.
TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.
TM
3GPP and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI
---------------------- Page: 2 ----------------------
3 Final draft ETSI EN 300 330-1 V1.8.1 (2014-12)
Contents
Intellectual Property Rights . 7
Foreword . 7
Modal verbs terminology . 7
Introduction . 8
1 Scope . 9
2 References . 10
2.1 Normative references . 10
2.2 Informative references . 11
3 Definitions, symbols and abbreviations . 12
3.1 Definitions . 12
3.2 Symbols . 13
3.3 Abbreviations . 14
4 Technical requirements specifications . 15
4.1 General requirements . 15
4.1.1 Receiver categorization . 15
4.1.2 General performance criteria . 15
4.1.3 General performance criteria for wireless power transfer (WPT) systems . 15
4.2 Presentation of equipment for testing purposes . 17
4.2.1 Choice of model for testing . 17
4.2.2 Testing of equipment with alternative radiated H-field strengths . 18
4.2.3 Testing of equipment that does not have an external 50 Ω RF connector (integral antenna
equipment) . 18
4.2.3.1 Equipment with an internal permanent or temporary antenna connector . 18
4.2.3.2 Equipment with a temporary antenna connector . 18
4.2.3.3 Wireless Power Transfer systems . 18
4.2.4 On-site testing . 18
4.3 Mechanical and electrical design . 18
4.3.1 General . 18
4.3.1.1 WPT . 18
4.3.2 Controls . 18
4.3.3 Transmitter shut-off facility . 19
4.3.4 Receiver mute or squelch . 19
4.3.5 Marking (equipment identification) . 19
4.3.5.1 Equipment identification . 19
4.3.5.2 Equipment marking . 19
4.4 Declarations by the provider . 19
4.5 Auxiliary test equipment . 19
4.6 Interpretation of the measurement results . 19
5 Test conditions, power sources and ambient temperatures . 20
5.1 Normal and extreme test conditions . 20
5.2 Test power source . 20
5.2.1 External test power source . 20
5.2.2 Internal test power source . 20
5.3 Normal test conditions . 20
5.3.1 Normal temperature and humidity . 20
5.3.2 Normal test power source . 21
5.3.2.1 Mains voltage . 21
5.3.2.2 Regulated lead-acid battery power sources . 21
5.3.2.3 Other power sources . 21
5.4 Extreme test conditions . 21
5.4.1 Extreme temperatures . 21
5.4.1.1 Procedure for tests at extreme temperatures . 21
ETSI
---------------------- Page: 3 ----------------------
4 Final draft ETSI EN 300 330-1 V1.8.1 (2014-12)
5.4.1.1.1 Procedure for equipment designed for continuous operation . 21
5.4.1.1.2 Procedure for equipment designed for intermittent operation . 21
5.4.1.2 Extreme temperature ranges . 22
5.4.2 Extreme test source voltages . 22
5.4.2.1 Mains voltage . 22
5.4.2.2 Regulated lead-acid battery power sources . 22
5.4.2.3 Power sources using other types of batteries . 22
5.4.2.4 Other power sources . 23
6 General conditions . 23
6.1 Normal test signals and test modulation . 23
6.1.1 Normal test signals for analogue speech . 23
6.1.2 Normal test signals for data . 23
6.2 Artificial antenna . 23
6.2.1 Artificial antenna for inductive transmitters (non 50 Ω) . 23
6.2.2 Artificial antenna for transmitters with 50 Ω impedance connector . 24
6.3 Test fixture . 24
6.4 Test sites and general arrangements for radiated measurements . 25
6.5 Modes of operation of the transmitter . 25
6.6 Measuring receiver . 25
7 Transmitter requirements . 25
7.1 Transmitter definitions . 26
7.1.1 The inductive loop coil transmitters . 26
7.1.2 The large size loop transmitters . 26
7.1.3 Other transmitters . 26
7.1.4 Product Classes . 26
7.2 Transmitter carrier output levels . 30
7.2.1 H-field (radiated) . 30
7.2.1.1 Definition . 30
7.2.1.2 Methods of measurement . 30
7.2.1.3 Limits . 30
7.2.2 RF carrier current (Product Class 3 only) . 32
7.2.2.1 Definition . 32
7.2.2.2 Methods of measurement . 32
7.2.2.3 Limits . 32
7.2.3 Radiated E-field (Product Class 4 only) . 32
7.2.3.1 Definition . 32
7.2.3.2 Methods of measurement . 32
7.2.3.3 Limits . 33
7.3 Permitted range of operating frequencies . 33
7.3.1 Definition . 33
7.3.2 Method of measurement . 33
7.3.3 Limits . 33
7.4 Permitted frequency range of the modulation bandwidth . 33
7.4.1 Definition . 34
7.4.2 Method of measurement . 34
7.4.3 Limits . 34
7.5 Spurious domain emission limits . 35
7.5.1 Definition . 35
7.5.2 Conducted spurious emissions (Product class 3 only) . 35
7.5.2.1 Methods of measurement (< 30 MHz) . 35
7.5.2.2 Limits . 35
7.5.2.3 Methods of measurement (≥ 30 MHz) . 35
7.5.2.4 Limits . 36
7.5.3 Radiated field strength . 36
7.5.3.1 Methods of measurement (< 30 MHz) . 36
7.5.3.2 Limits . 36
7.5.4 Effective radiated power . 36
7.5.4.1 Methods of measurement (≥ 30 MHz) . 37
7.5.4.2 Limits . 37
8 Receiver requirement . 38
ETSI
---------------------- Page: 4 ----------------------
5 Final draft ETSI EN 300 330-1 V1.8.1 (2014-12)
8.1 Adjacent channel selectivity - in band . 38
8.1.1 Definition . 38
8.1.2 Method of measurement . 38
8.1.3 Limits . 39
8.2 Blocking or desensitization (Receiver category 1 and 2 only) . 39
8.2.1 Definition . 39
8.2.2 Methods of measurement . 39
8.2.3 Limits . 40
8.3 Receiver spurious radiation . 40
8.3.1 Definition . 41
8.3.2 Methods of measurement . 41
8.3.3 Limits . 41
8.3.3.1 Radiated emissions below 30 MHz . 41
8.3.3.2 Radiated emissions above 30 MHz . 41
9 Measurement uncertainty . 41
10 Interpretation of results . 42
10.1 Measurement uncertainty is equal to or less than maximum acceptable uncertainty . 42
Annex A (normative): Radiated measurement . 43
A.1 Test sites and general arrangements for measurements involving the use of radiated fields . 43
A.1.1 Anechoic chamber . 43
A.1.2 Anechoic chamber with a conductive ground plane . 44
A.1.3 Open Area Test Site (OATS) . 45
A.1.3.1 Measurements below 30 MHz . 46
A.1.3.2 Measurements above 30 MHz . 46
A.1.4 Test antenna . 47
A.1.5 Substitution antenna . 48
A.1.6 Measuring antenna . 48
A.2 Guidance on the use of radiation test sites . 48
A.2.1 Verification of the test site . 48
A.2.2 Preparation of the EUT . 48
A.2.3 Power supplies to the EUT . 48
A.2.4 Range length . 49
A.2.4.1 Far-field length above 30 MHz . 49
A.2.4.2 Near-field and Far-field length below 30 MHz . 49
A.2.5 Site preparation . 50
A.3 Coupling of signals . 50
A.3.1 General . 50
A.3.2 Data signals . 50
A.4 Standard test position . 50
A.5 Test fixture . 51
A.5.1 Description . 51
A.5.2 Calibration . 52
A.5.3 Mode of use . 52
A.6 Technical performance of the spectrum analyser . 53
Annex B (normative): H-field limit correction factor for generated E-fields . 54
Annex C (normative): Customized loop antennas . 55
C.1 Product classes related to the antenna loop . 55
C.1.1 Antenna loops below 1 MHz . 55
C.1.2 Antenna loops above 1 MHz . 56
Annex D (informative): Test fixture for measuring inductive transmitter carrier and
harmonic currents by use of an artificial antenna (Product Class 3
only) . 58
ETSI
---------------------- Page: 5 ----------------------
6 Final draft ETSI EN 300 330-1 V1.8.1 (2014-12)
Annex E (informative): E-fields in the near field at low frequencies . 60
Annex F (normative): H-field measurements and limits at 3 m and 30 m . 61
F.1 Limits for measurements at 30 m distance . 61
F.2 Limits for measurements at 3 m distance . 62
Annex G (normative): Transmitter emission levels and spectrum mask measurements . 63
Annex H (normative): Generic inductive loop limits in the frequency range
148,5 kHz to 30 MHz . 66
H.1 Introduction . 66
H.2 Radiated H-field strength . 66
H.2.1 Methods of measurements . 66
H.2.2 Radiated H-field strength limit .
...
Draft ETSI EN 300 330-1 V1.8.0 (2014-06)
European Standard
Electromagnetic compatibility
and Radio spectrum Matters (ERM);
Short Range Devices (SRD);
Radio equipment in the frequency range
9 kHz to 25 MHz and inductive loop systems
in the frequency range 9 kHz to 30 MHz;
Part 1: Technical characteristics and test methods
---------------------- Page: 1 ----------------------
2 Draft ETSI EN 300 330-1 V1.8.0 (2014-06)
Reference
REN/ERM-TG28-0436
Keywords
Radio, RFID, SRD, testing
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
http://portal.etsi.org/chaircor/ETSI_support.asp
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2014.
All rights reserved.
TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.
TM
3GPP and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI
---------------------- Page: 2 ----------------------
3 Draft ETSI EN 300 330-1 V1.8.0 (2014-06)
Contents
Intellectual Property Rights . 7
Foreword . 7
Modal verbs terminology . 7
Introduction . 7
1 Scope . 9
2 References . 10
2.1 Normative references . 10
2.2 Informative references . 11
3 Definitions, symbols and abbreviations . 12
3.1 Definitions . 12
3.2 Symbols . 13
3.3 Abbreviations . 13
4 Technical requirements specifications . 14
4.1 General requirements . 14
4.1.1 Receiver categorization . 14
4.1.2 General performance criteria . 15
4.1.3 General performance criteria for wireless power transfer (WPT) systems . 15
4.2 Presentation of equipment for testing purposes . 16
4.2.1 Choice of model for testing . 17
4.2.2 Testing of equipment with alternative radiated H-field strengths . 17
4.2.3 Testing of equipment that does not have an external 50 Ω RF connector (integral antenna
equipment) . 17
4.2.3.1 Equipment with an internal permanent or temporary antenna connector . 17
4.2.3.2 Equipment with a temporary antenna connector . 17
4.2.3.3 Wireless Power Transfer systems . 18
4.2.4 On-site testing . 18
4.3 Mechanical and electrical design . 18
4.3.1 General . 18
4.3.1.1 WPT . 18
4.3.2 Controls . 18
4.3.3 Transmitter shut-off facility . 18
4.3.4 Receiver mute or squelch . 18
4.3.5 Marking (equipment identification) . 18
4.3.5.1 Equipment identification . 18
4.3.5.2 Equipment marking . 19
4.4 Declarations by the provider . 19
4.5 Auxiliary test equipment . 19
4.6 Interpretation of the measurement results . 19
5 Test conditions, power sources and ambient temperatures . 19
5.1 Normal and extreme test conditions . 19
5.2 Test power source . 19
5.2.1 External test power source . 19
5.2.2 Internal test power source . 20
5.3 Normal test conditions . 20
5.3.1 Normal temperature and humidity . 20
5.3.2 Normal test power source . 20
5.3.2.1 Mains voltage . 20
5.3.2.2 Regulated lead-acid battery power sources . 20
5.3.2.3 Other power sources . 20
5.4 Extreme test conditions . 20
5.4.1 Extreme temperatures . 20
5.4.1.1 Procedure for tests at extreme temperatures . 20
ETSI
---------------------- Page: 3 ----------------------
4 Draft ETSI EN 300 330-1 V1.8.0 (2014-06)
5.4.1.1.1 Procedure for equipment designed for continuous operation . 21
5.4.1.1.2 Procedure for equipment designed for intermittent operation . 21
5.4.1.2 Extreme temperature ranges . 21
5.4.2 Extreme test source voltages . 21
5.4.2.1 Mains voltage . 21
5.4.2.2 Regulated lead-acid battery power sources . 22
5.4.2.3 Power sources using other types of batteries . 22
5.4.2.4 Other power sources . 22
6 General conditions . 22
6.1 Normal test signals and test modulation . 22
6.1.1 Normal test signals for analogue speech . 22
6.1.2 Normal test signals for data . 23
6.2 Artificial antenna . 23
6.2.1 Artificial antenna for inductive transmitters (non 50 Ω) . 23
6.2.2 Artificial antenna for transmitters with 50 Ω impedance connector . 23
6.3 Test fixture . 24
6.4 Test sites and general arrangements for radiated measurements . 24
6.5 Modes of operation of the transmitter . 24
6.6 Measuring receiver . 25
7 Transmitter requirements . 25
7.1 Transmitter definitions . 25
7.1.1 The inductive loop coil transmitters . 25
7.1.2 The large size loop transmitters . 26
7.1.3 Other transmitters . 26
7.1.4 Product Classes . 26
7.2 Transmitter carrier output levels . 30
7.2.1 H-field (radiated) . 30
7.2.1.1 Definition . 30
7.2.1.2 Methods of measurement . 30
7.2.1.3 Limits . 30
7.2.2 RF carrier current (Product Class 3 only) . 31
7.2.2.1 Definition . 31
7.2.2.2 Methods of measurement . 32
7.2.2.3 Limits . 32
7.2.3 Radiated E-field (Product Class 4 only) . 32
7.2.3.1 Definition . 32
7.2.3.2 Methods of measurement . 32
7.2.3.3 Limits . 33
7.3 Permitted range of operating frequencies . 33
7.3.1 Definition . 33
7.3.2 Method of measurement . 33
7.3.3 Limits . 33
7.4 Permitted frequency range of the modulation bandwidth . 34
7.4.1 Definition . 34
7.4.2 Method of measurement . 34
7.4.3 Limits . 34
7.5 Spurious domain emission limits . 35
7.5.1 Definition . 35
7.5.2 Conducted spurious emissions (Product class 3 only) . 35
7.5.2.1 Methods of measurement (< 30 MHz) . 35
7.5.2.2 Limits . 35
7.5.2.3 Methods of measurement (≥ 30 MHz) . 35
7.5.2.4 Limits . 36
7.5.3 Radiated field strength . 36
7.5.3.1 Methods of measurement (< 30 MHz) . 36
7.5.3.2 Limits . 36
7.5.4 Effective radiated power . 36
7.5.4.1 Methods of measurement (≥ 30 MHz) . 37
7.5.4.2 Limits . 37
8 Receiver requirement . 38
ETSI
---------------------- Page: 4 ----------------------
5 Draft ETSI EN 300 330-1 V1.8.0 (2014-06)
8.1 Adjacent channel selectivity - in band . 38
8.1.1 Definition . 38
8.1.2 Method of measurement . 38
8.1.3 Limits . 39
8.2 Blocking or desensitization (Receiver category 1 and 2 only) . 39
8.2.1 Definition . 39
8.2.2 Methods of measurement . 39
8.2.3 Limits . 40
8.3 Receiver spurious radiation . 40
8.3.1 Definition . 41
8.3.2 Methods of measurement . 41
8.3.3 Limits . 41
8.3.3.1 Radiated emissions below 30 MHz . 41
8.3.3.2 Radiated emissions above 30 MHz . 41
9 Measurement uncertainty . 41
10 Interpretation of results . 42
10.1 Measurement uncertainty is equal to or less than maximum acceptable uncertainty . 42
Annex A (normative): Radiated measurement . 43
A.1 Test sites and general arrangements for measurements involving the use of radiated fields . 43
A.1.1 Anechoic chamber . 43
A.1.2 Anechoic chamber with a conductive ground plane . 44
A.1.3 Open Area Test Site (OATS) . 45
A.1.3.1 Measurements below 30 MHz . 46
A.1.3.2 Measurements above 30 MHz . 46
A.1.4 Test antenna . 47
A.1.5 Substitution antenna . 48
A.1.6 Measuring antenna . 48
A.2 Guidance on the use of radiation test sites . 48
A.2.1 Verification of the test site . 48
A.2.2 Preparation of the EUT . 48
A.2.3 Power supplies to the EUT . 48
A.2.4 Range length . 49
A.2.4.1 Far-field length above 30 MHz . 49
A.2.4.2 Near-field and Far-field length below 30 MHz . 49
A.2.5 Site preparation . 50
A.3 Coupling of signals . 50
A.3.1 General . 50
A.3.2 Data signals . 50
A.4 Standard test position . 50
A.5 Test fixture . 51
A.5.1 Description . 51
A.5.2 Calibration . 52
A.5.3 Mode of use . 52
A.6 Technical performance of the spectrum analyser . 53
Annex B (normative): H-field limit correction factor for generated E-fields . 54
Annex C (normative): Customized loop antennas . 55
C.1 Product classes related to the antenna loop . 55
C.1.1 Antenna loops below 1 MHz . 55
C.1.2 Antenna loops above 1 MHz . 56
Annex D (informative): Test fixture for measuring inductive transmitter carrier and
harmonic currents by use of an artificial antenna (Product Class 3
only) . 58
ETSI
---------------------- Page: 5 ----------------------
6 Draft ETSI EN 300 330-1 V1.8.0 (2014-06)
Annex E (informative): E-fields in the near field at low frequencies . 60
Annex F (normative): H-field measurements and limits at 3 m and 30 m . 61
F.1 Limits for measurements at 30 m distance . 61
F.2 Limits for measurements at 3 m distance . 62
Annex G (normative): Transmitter emission levels and spectrum mask measurements . 63
Annex H (normative): Generic inductive loop limits in the frequency range
148,5 kHz to 30 MHz . 66
H.1 Introduction . 66
H.2 Radiated H-field strength . 66
H.2.1 Methods of measurements . 66
H.2.2 Radiated H-field strength limit .
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.