SIST EN IEC 60512-28-100:2025
(Main)Connectors for electrical and electronic equipment - Tests and measurements - Part 28-100: Signal integrity tests up to 2 000 MHz - Tests 28a to 28g (IEC 60512-28-100:2024)
Connectors for electrical and electronic equipment - Tests and measurements - Part 28-100: Signal integrity tests up to 2 000 MHz - Tests 28a to 28g (IEC 60512-28-100:2024)
IEC 60512-28-100:2024 specifies the test methods for signal integrity and transmission performance for connectors specified in respective parts of IEC 60603-7, IEC61076-1, IEC 61076-2, IEC 61076-3 and IEC 63171 series of standards for connecting hardware applications from 0,1 MHz up to 2 000 MHz, with reference to this document.
Note: This document is also suitable for testing signal integrity and transmission performance of connectors up to a lower value of maximum frequency; however, the test methodology specified in the detail specification for any given connector remains the reference conformance test for that connector.
The list of connector series of standards does not preclude referencing this document in other connector manufacturer’s specifications or published standards.
Test procedures provided herein are:
- insertion loss, test 28a;
- return loss, test 28b;
- near-end crosstalk (NEXT) test 28c;
- far-end crosstalk (FEXT), test 28d;
- transverse conversion loss (TCL), test 28f;
- transverse conversion transfer loss (TCTL), test 28g.
Other test procedures referenced herein are:
- shield transfer impedance (ZT), see IEC 60512‑26‑100, test 26e.
- coupling attenuation (aC), see IEC 62153-4-7 and IEC 62153‑4‑12.
- low frequency coupling attenuation (aCLF) see IEC 62153-4-7 and IEC 62153-4-15
This edition includes the following significant technical changes with respect to the previous edition:
-The frequency range has been modified to start at 0,1 MHz instead of 1 MHz, to include single-pair connectors.
-All tables and requirements have been revised down to 0,1 MHz, and partially improved to reduce the impact of the test fixture.
-Formulae to calculate the S-parameters from single-ended parameters have been added.
-A note was added for those parameters which are not applicable to single-pair connectors.
Steckverbinder für elektrische und elektronische Einrichtungen - Mess- und Prüfverfahren - Teil 28-100: Signalintegritätsprüfungen bis 2 000 MHz - Prüfungen 28a bis 28g (IEC 60512-28-100:2024)
Connecteurs pour équipements électriques et électroniques - Essais et mesures - Partie 28-100: Essais d'intégrité des signaux jusqu'à 2 000 MHz - Essais 28a à 28g (IEC 60512-28-100:2024)
L'IEC 60512-28-100:2024 spécifie les méthodes d’essai pour l’intégrité du signal et les performances de transmission pour les connecteurs spécifiés dans les parties respectives de l'IEC 60603-7, l'IEC 61076-1, l'IEC 61076-2, l'IEC 61076-3 et de la série de normes IEC 63171 pour connecter les applications matérielles de 0,1 MHz à 2 000 MHz, en référence au présent document.
NOTE Le présent document convient également pour soumettre à essai l’intégrité des signaux et les performances de transmission des connecteurs jusqu’à une valeur inférieure de fréquence maximale; toutefois, la méthodologie d’essai spécifiée dans la spécification particulière pour un connecteur donné reste l’essai de conformité de référence pour ce connecteur.
La liste de séries de normes concernant les connecteurs n’exclut pas le fait de faire référence au présent document dans d’autres normes publiées ou spécifications des fabricants de connecteurs.
Les procédures d’essai spécifiées ici sont les suivantes:
- perte d’insertion, essai 28a;
- affaiblissement de réflexion, essai 28b;
- paradiaphonie (NEXT), essai 28c;
- télédiaphonie (FEXT), essai 28d;
- perte de conversion transverse (TCL), essai 28f;
- perte de transfert de conversion transverse (TCTL), essai 28g.
Les autres procédures d’essai citées ici en référence sont:
- impédance de transfert, (ZT), voir l’IEC 60512‑26‑100, essai 26e;
- affaiblissement de couplage (aC), voir l’IEC 62153-4-7 et l’IEC 62153‑4‑12;
- affaiblissement de couplage basse fréquence (aCLF), voir l’IEC 62153-4-7 et l’IEC 62153-4-15.
Konektorji za električno in elektronsko opremo - Preskusi in meritve - 28-100. del: Preskusi signalne celovitosti do 2000 MHz - Preskusi od 28a do 28g (IEC 60512-28-100:2024)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-januar-2025
Konektorji za električno in elektronsko opremo - Preskusi in meritve - 28-100. del:
Preskusi signalne celovitosti do 2000 MHz - Preskusi od 28a do 28g (IEC 60512-28-
100:2024)
Connectors for electrical and electronic equipment - Tests and measurements - Part 28-
100: Signal integrity tests up to 2 000 MHz - Tests 28a to 28g (IEC 60512-28-100:2024)
Steckverbinder für elektrische und elektronische Einrichtungen - Mess- und
Prüfverfahren - Teil 28-100: Signalintegritätsprüfungen bis 2 000 MHz - Prüfungen 28a
bis 28g (IEC 60512-28-100:2024)
Connecteurs pour équipements électriques et électroniques - Essais et mesures - Partie
28-100: Essais d'intégrité des signaux jusqu'à 2 000 MHz - Essais 28a à 28g (IEC 60512
-28-100:2024)
Ta slovenski standard je istoveten z: EN IEC 60512-28-100:2024
ICS:
31.220.10 Vtiči in vtičnice, konektorji Plug-and-socket devices.
Connectors
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD EN IEC 60512-28-100
NORME EUROPÉENNE
EUROPÄISCHE NORM November 2024
ICS 31.220.10 Supersedes EN IEC 60512-28-100:2019
English Version
Connectors for electrical and electronic equipment - Tests and
measurements - Part 28-100: Signal integrity tests up to 2 000
MHz - Tests 28a to 28g
(IEC 60512-28-100:2024)
Connecteurs pour équipements électriques et électroniques Steckverbinder für elektrische und elektronische
- Essais et mesures - Partie 28-100: Essais d'intégrité des Einrichtungen - Mess- und Prüfverfahren - Teil 28-100:
signaux jusqu'à 2 000 MHz - Essais 28a à 28g Signalintegritätsprüfungen bis 2 000 MHz - Prüfungen 28a
(IEC 60512-28-100:2024) bis 28g
(IEC 60512-28-100:2024)
This European Standard was approved by CENELEC on 2024-09-06. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Türkiye and the United Kingdom.
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2024 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN IEC 60512-28-100:2024 E
European foreword
The text of document 48B/3109/FDIS, future edition 3 of IEC 60512-28-100, prepared by SC 48B
"Electrical connectors" of IEC/TC 48 "Electrical connectors and mechanical structures for electrical
and electronic equipment" was submitted to the IEC-CENELEC parallel vote and approved by
CENELEC as EN IEC 60512-28-100:2024.
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2025-11-30
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2027-11-30
document have to be withdrawn
This document supersedes EN IEC 60512-28-100:2019 and all of its amendments and corrigenda (if
any).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
Any feedback and questions on this document should be directed to the users’ national committee. A
complete listing of these bodies can be found on the CENELEC website.
Endorsement notice
The text of the International Standard IEC 60512-28-100:2024 was approved by CENELEC as a
European Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standard indicated:
IEC 60603-7 NOTE Approved as EN IEC 60603-7
IEC 61076-1 NOTE Approved as EN 61076-1
IEC 61076-2 NOTE Approved as EN 61076-2
IEC 61076-3 NOTE Approved as EN 61076-3
IEC 63171 NOTE Approved as EN IEC 63171
IEC 60603-7-81 NOTE Approved as EN 60603-7-81
IEC 60603-7-82 NOTE Approved as EN 60603-7-82
IEC 61076-3-110 NOTE Approved as EN 61076-3-110
IEC 61076-3-104 NOTE Approved as EN 61076-3-104
IEC 61076-2-109 NOTE Approved as EN 61076-2-109
IEC 60603-7-2 NOTE Approved as EN 60603-7-2
IEC 60603-7-3 NOTE Approved as EN 60603-7-3
IEC 60603-7-4 NOTE Approved as EN 60603-7-4
IEC 60603-7-5 NOTE Approved as EN 60603-7-5
IEC 60603-7-41 NOTE Approved as EN 60603-7-41
IEC 60603-7-51 NOTE Approved as EN 60603-7-51
IEC 60603-7-7 NOTE Approved as EN 60603-7-7
IEC 60603-7-71 NOTE Approved as EN 60603-7-71
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1 Where an International Publication has been modified by common modifications, indicated by (mod), the
relevant EN/HD applies.
NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available
here: www.cencenelec.eu.
Publication Year Title EN/HD Year
IEC 60050-581 - International Electrotechnical Vocabulary - - -
Part 581: Electromechanical components
for electronic equipment
IEC 60512-1 - Connectors for electrical and electronic EN IEC 60512-1 -
equipment - Tests and measurements -
Part 1: Generic specification
IEC 60512-26-100 - Connectors for electronic equipment - EN 60512-26-100 -
Tests and measurements - Part 26-100:
Measurement setup, test and reference
arrangements and measurements for
connectors according to IEC 60603-7 -
Tests 26a to 26g
IEC 60512-27-100 - Connectors for electronic equipment - EN 60512-27-100 -
Tests and measurements - Part 27-100:
Signal integrity tests up to 500 MHz on
60603-7 series connectors - Tests 27a to
27g
IEC 60512-27-200 - Connectors for electrical and electronic EN IEC 60512-27-200 -
equipment - Tests and measurements -
Part 27-200: Additional specifications for
signal integrity tests up to 2 000 MHz on
IEC 60603-7 series connectors - Tests 27a
to 27g
IEC 60512-29-100 - Connectors for electronic equipment - EN 60512-29-100 -
Tests and measurements - Part 29-100:
Signal integrity tests up to 500 MHz on
M12 style connectors - Tests 29a to 29g
IEC 60603-7 - Connectors for electronic equipment - Part EN IEC 60603-7 -
7: Detail specification for 8-way,
unshielded, free and fixed connectors
IEC 61076-1 - Connectors for electronic equipment - EN 61076-1 -
Product requirements - Part 1: Generic
specification
IEC 61076-3-104 - Connectors for electrical and electronic EN 61076-3-104 -
equipment - Product requirements - Part 3-
104: Detail specification for 8-way,
shielded free and fixed connectors for data
transmissions with frequencies up to 2 000
MHz
IEC 61076-3-110 - Connectors for electrical and electronic EN 61076-3-110 -
equipment - Product requirements - Part 3-
110: Detail specification for free and fixed
connectors for data transmission with
frequencies up to 3 000 MHz
IEC 61156-1 - Multicore and symmetrical pair/quad - -
cables for digital communications - Part 1:
Generic specification
IEC 61169-15 - Radio-frequency connectors - Part 15: EN IEC 61169-15 -
Sectional specification - RF coaxial
connectors with inner diameter of outer
conductor 4,13 mm (0,163 in) with
threaded coupling - Characteristic
impedance 50 Ω (type SMA)
IEC 61169-16 - Radio-frequency connectors - Part 16: EN 61169-16 -
Sectional specification - RF coaxial
connectors with inner diameter of outer
conductor 7 mm (0,276 in) with screw
coupling - Characteristics impedance 50
ohms (75 ohms) (type N)
IEC 62153-4-6 - Metallic cables and other passive - -
components test methods - Part 4-6:
Electromagnetic compatibility (EMC) -
Surface transfer impedance - line injection
method
IEC 62153-4-7 - Metallic cables and other passive EN IEC 62153-4-7 -
components test methods - Part 4-7:
Electromagnetic compatibility (EMC) -Test
method for measuring of transfer
impedance Z and screening attenuation
T
aS or coupling attenuation aC of connectors
and assemblies - Triaxial tube in tube
method
IEC 62153-4-12 - Metallic communication cable test methods - -
- Part 4-12: Electromagnetic compatibility
(EMC) - Coupling attenuation or screening
attenuation of connecting hardware -
Absorbing clamp method
IEC 62153-4-15 - Metallic cables and other passive EN IEC 62153-4-15 -
components test methods - Part 4-15:
Electromagnetic compatibility (EMC) - Test
method for measuring transfer impedance
and screening attenuation - or coupling
attenuation with triaxial cell
IEC 63171 - Connectors for electrical and electronic EN IEC 63171 -
equipment - Shielded or unshielded free
and fixed connectors for balanced single-
pair data transmission with current-carrying
capacity - General requirements and tests
ISO/IEC 11801-1 - Information technology - Generic cabling - -
for customer premises - Part 1: General
requirements
IEC 60512-28-100 ®
Edition 3.0 2024-08
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
colour
inside
Connectors for electrical and electronic equipment – Tests and measurements –
Part 28-100: Signal integrity tests up to 2 000 MHz – Tests 28a to 28g
Connecteurs pour équipements électriques et électroniques – Essais
et mesures –
Partie 28-100: Essais d’intégrité des signaux jusqu’à 2 000 MHz – Essais 28a
à 28g
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 31.220.10 ISBN 978-2-8322-9504-5
– 2 – IEC 60512-28-100:2024 © IEC 2024
CONTENTS
FOREWORD . 6
1 Scope . 8
2 Normative references . 8
3 Terms, definitions and abbreviated terms . 10
3.1 Terms and definitions. 10
3.2 Abbreviated terms . 10
4 Overall test arrangement . 11
4.1 General . 11
4.2 Test instrumentation . 11
4.2.1 General . 11
4.2.2 Vector network analyser . 11
4.2.3 RF switching unit . 11
4.2.4 Reference loads and termination loads . 11
4.3 Measurement precautions . 12
4.4 Mixed mode S-parameter nomenclature . 12
4.5 Coaxial cables and interconnections for network analysers . 13
4.6 Characteristic for switching matrices . 14
4.7 Test fixture types . 14
4.8 Requirements for termination performance at calibration plane . 14
4.9 Reference loads for calibration . 14
4.10 Calibration . 15
4.10.1 General . 15
4.10.2 Calibration test interface .
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.