SIST EN ISO 9693-1:2012
(Main)Dentistry - Compatibility testing - Part 1: Metal-ceramic systems (ISO 9693-1:2012)
Dentistry - Compatibility testing - Part 1: Metal-ceramic systems (ISO 9693-1:2012)
This part of ISO 9693 specifies test methods for determining the compatibility of metallic and ceramic materials used for dental restorations by testing the composite structure. The requirements given in this part of ISO 9693 are applicable to metallic materials and ceramics when used in combination, and are not applicable to either metallic materials or ceramics when used alone.
Zahnheilkunde - Verbundprüfung - Teil 1: Metall-Keramiksysteme (ISO 9693-1:2012)
Diese Internationale Norm legt Prüfverfahren zur Bestimmung der Verträglichkeit metallischer und keramischer Werkstoffe, die zur Herstellung von Restaurationen in der Zahnheilkunde verwendet werden, fest, indem die Verbundstruktur geprüft wird.
Die Anforderungen dieser Internationalen Norm gelten für metallische Werkstoffe und Keramiken, wenn sie zusammen im Verbund verwendet werden, und die Erfüllung der Anforderungen darf nicht allein für die metallischen Werkstoffe oder die Keramiken behauptet werden.
Zu Anforderungen an metallische Werkstoffe siehe ISO 22674:2006.
Zu Anforderungen an keramische Werkstoffe siehe ISO 6872:2008.
Médecine bucco-dentaire - Essais de compatibilité - Partie 1: Systèmes métallo-céramiques (ISO 9693-1:2012)
Art dentaire - Systèmes pour restaurations dentaires métallo-céramiques
Zobozdravstvo - Preskušanje združljivosti - 1. del: Kovinsko-keramični sistemi (ISO 9693-1:2012)
Ta del standarda ISO 9693 določa preskusne metode za določanje združljivosti kovinskih in keramičnih materialov, ki se uporabljajo za popravila zob, s preskušanjem njihove kompozitne strukture. Zahteve iz tega dela standarda ISO 9693 veljajo za kovinske in keramične materiale, kadar se uporabljajo skupaj, ne veljajo pa za kovinske ali keramične materiale, uporabljene ločeno.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 9693-1:2012
01-maj-2012
1DGRPHãþD
SIST EN ISO 9693:2001
=RER]GUDYVWYR3UHVNXãDQMH]GUXåOMLYRVWLGHO .RYLQVNRNHUDPLþQLVLVWHPL
,62
Dentistry - Compatibility testing - Part 1: Metal-ceramic systems (ISO 9693-1:2012)
Zahnheilkunde - Verbundprüfung - Teil 1: Metall-Keramiksysteme (ISO 9693-1:2012)
Médecine bucco-dentaire - Essais de compatibilité - Partie 1: Systèmes métallo-
céramiques (ISO 9693-1:2012)
Ta slovenski standard je istoveten z: EN ISO 9693-1:2012
ICS:
11.060.10 =RERWHKQLþQLPDWHULDOL Dental materials
SIST EN ISO 9693-1:2012 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 9693-1:2012
---------------------- Page: 2 ----------------------
SIST EN ISO 9693-1:2012
EUROPEAN STANDARD
EN ISO 9693-1
NORME EUROPÉENNE
EUROPÄISCHE NORM
February 2012
ICS 11.060.10 Supersedes EN ISO 9693:2000
English Version
Dentistry - Compatibility testing - Part 1: Metal-ceramic systems
(ISO 9693-1:2012)
Médecine bucco-dentaire - Essais de compatibilité - Partie Zahnheilkunde - Verbundprüfung - Teil 1: Metall-
1: Systèmes métallo-céramiques (ISO 9693-1:2012) Keramiksysteme (ISO 9693-1:2012)
This European Standard was approved by CEN on 14 February 2012.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2012 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 9693-1:2012: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 9693-1:2012
EN ISO 9693-1:2012 (E)
Contents Page
Foreword .3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 9693-1:2012
EN ISO 9693-1:2012 (E)
Foreword
This document (EN ISO 9693-1:2012) has been prepared by Technical Committee ISO/TC 106 "Dentistry" in
collaboration with Technical Committee CEN/TC 55 “Dentistry” the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by August 2012, and conflicting national standards shall be withdrawn at
the latest by August 2012.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 9693:2000.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland, Turkey and the United Kingdom.
Endorsement notice
The text of ISO 9693-1:2012 has been approved by CEN as a EN ISO 9693-1:2012 without any modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 9693-1:2012
---------------------- Page: 6 ----------------------
SIST EN ISO 9693-1:2012
INTERNATIONAL ISO
STANDARD 9693-1
First edition
2012-02-15
Dentistry — Compatibility testing —
Part 1:
Metal-ceramic systems
Médecine bucco-dentaire — Essais de compatibilité —
Partie 1: Systèmes métallo-céramiques
Reference number
ISO 9693-1:2012(E)
©
ISO 2012
---------------------- Page: 7 ----------------------
SIST EN ISO 9693-1:2012
ISO 9693-1:2012(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2012
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO’s
member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2012 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 9693-1:2012
ISO 9693-1:2012(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International
Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 9693-1 was prepared by Technical Committee ISO/TC 106, Dentistry, Subcommittee SC 2,
Prosthodontic materials.
1)
This first edition of ISO 9693-1, together with ISO 9693-2 , cancels and replaces ISO 9693:1999. It also
incorporates the Amendment ISO 9693:1999/Amd 1:2005.
ISO 9693 consists of the following parts, under the general title Dentistry — Compatibility testing:
— Part 1: Metal-ceramic systems
The following parts are under preparation:
— Part 2: Ceramic-ceramic systems
1) Under preparation.
© ISO 2012 – All rights reserved iii
---------------------- Page: 9 ----------------------
SIST EN ISO 9693-1:2012
ISO 9693-1:2012(E)
Introduction
Dental metallic materials and ceramics are suitable for use in the fabrication of metal-ceramic dental restorations.
iv © ISO 2012 – All rights reserved
---------------------- Page: 10 ----------------------
SIST EN ISO 9693-1:2012
INTERNATIONAL STANDARD ISO 9693-1:2012(E)
Dentistry — Compatibility testing —
Part 1:
Metal-ceramic systems
1 Scope
This part of ISO 9693 specifies test methods for determining the compatibility of metallic and ceramic materials
used for dental restorations by testing the composite structure.
The requirements given in this
...
SLOVENSKI STANDARD
oSIST prEN ISO 9693-1:2010
01-oktober-2010
=RER]GUDYVWYR3UHVNXãDQMH]GUXåOMLYRVWLGHO .RYLQVNRNHUDPLþQLVLVWHPL
,62',6
Dentistry - Compatibility testing - Part 1: Metal-ceramic systems (ISO/DIS 9693-1:2010)
Zahnheilkunde - Verbundprüfung - Teil 1: Metall-Keramiksysteme (ISO/DIS 9693-1:2010)
Médecine bucco-dentaire - Essais de compatibilité - Partie 1: Systèmes métallo-
céramiques (ISO/DIS 9693-1:2010)
Ta slovenski standard je istoveten z: prEN ISO 9693-1
ICS:
11.060.10 =RERWHKQLþQLPDWHULDOL Dental materials
oSIST prEN ISO 9693-1:2010 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN ISO 9693-1:2010
---------------------- Page: 2 ----------------------
oSIST prEN ISO 9693-1:2010
EUROPEAN STANDARD
DRAFT
prEN ISO 9693-1
NORME EUROPÉENNE
EUROPÄISCHE NORM
July 2010
ICS 11.060.10 Will supersede EN ISO 9693:2000
English Version
Dentistry - Compatibility testing - Part 1: Metal-ceramic systems
(ISO/DIS 9693-1:2010)
Médecine bucco-dentaire - Essais de compatibilité - Partie Zahnheilkunde - Verbundprüfung - Teil 1: Metall-
1: Systèmes métallo-céramiques (ISO/DIS 9693-1:2010) Keramiksysteme (ISO/DIS 9693-1:2010)
This draft European Standard is submitted to CEN members for parallel enquiry. It has been drawn up by the Technical Committee
CEN/TC 55.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations which
stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other language
made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the
same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to
provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2010 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN ISO 9693-1:2010: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
oSIST prEN ISO 9693-1:2010
prEN ISO 9693-1:2010 (E)
Contents Page
Foreword .3
2
---------------------- Page: 4 ----------------------
oSIST prEN ISO 9693-1:2010
prEN ISO 9693-1:2010 (E)
Foreword
This document (prEN ISO 9693-1:2010) has been prepared by Technical Committee ISO/TC 106 "Dentistry"
in collaboration with Technical Committee CEN/TC 55 “Dentistry” the secretariat of which is held by DIN.
This document is currently submitted to the parallel Enquiry.
This document will supersede EN ISO 9693:2000.
Endorsement notice
The text of ISO/DIS 9693-1:2010 has been approved by CEN as a prEN ISO 9693-1:2010 without any
modification.
3
---------------------- Page: 5 ----------------------
oSIST prEN ISO 9693-1:2010
---------------------- Page: 6 ----------------------
oSIST prEN ISO 9693-1:2010
DRAFT INTERNATIONAL STANDARD ISO/DIS 9693-1
ISO/TC 106/SC 2 Secretariat: ANSI
Voting begins on: Voting terminates on:
2010-07-08 2010-12-08
INTERNATIONAL ORGANIZATION FOR STANDARDIZATION • МЕЖДУНАРОДНАЯ ОРГАНИЗАЦИЯ ПО СТАНДАРТИЗАЦИИ • ORGANISATION INTERNATIONALE DE NORMALISATION
Dentistry — Compatibility testing —
Part 1:
Metal-ceramic systems
Médecine bucco-dentaire — Essais de compatibilité —
Partie 1: Systèmes métallo-céramiques
(Revision of second edition of ISO 9693:1999 and of ISO 9693:1999/Amd.1:2005)
ICS 11.060.10
ISO/CEN PARALLEL PROCESSING
This draft has been developed within the International Organization for Standardization (ISO), and
processed under the ISO-lead mode of collaboration as defined in the Vienna Agreement.
This draft is hereby submitted to the ISO member bodies and to the CEN member bodies for a parallel
five-month enquiry.
Should this draft be accepted, a final draft, established on the basis of comments received, will be
submitted to a parallel two-month approval vote in ISO and formal vote in CEN.
To expedite distribution, this document is circulated as received from the committee secretariat.
ISO Central Secretariat work of editing and text composition will be undertaken at publication
stage.
Pour accélérer la distribution, le présent document est distribué tel qu'il est parvenu du
secrétariat du comité. Le travail de rédaction et de composition de texte sera effectué au
Secrétariat central de l'ISO au stade de publication.
THIS DOCUMENT IS A DRAFT CIRCULATED FOR COMMENT AND APPROVAL. IT IS THEREFORE SUBJECT TO CHANGE AND MAY NOT BE
REFERRED TO AS AN INTERNATIONAL STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS BEING ACCEPTABLE FOR INDUSTRIAL, TECHNOLOGICAL, COMMERCIAL AND USER PURPOSES, DRAFT
INTERNATIONAL STANDARDS MAY ON OCCASION HAVE TO BE CONSIDERED IN THE LIGHT OF THEIR POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN NATIONAL REGULATIONS.
RECIPIENTS OF THIS DRAFT ARE INVITED TO SUBMIT, WITH THEIR COMMENTS, NOTIFICATION OF ANY RELEVANT PATENT RIGHTS OF WHICH
THEY ARE AWARE AND TO PROVIDE SUPPORTING DOCUMENTATION.
©
International Organization for Standardization, 2010
---------------------- Page: 7 ----------------------
oSIST prEN ISO 9693-1:2010
ISO/DIS 9693-1
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall
not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the
unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
Copyright notice
This ISO document is a Draft International Standard and is copyright-protected by ISO. Except as permitted
under the applicable laws of the user's country, neither this ISO draft nor any extract from it may be
reproduced, stored in a retrieval system or transmitted in any form or by any means, electronic, photocopying,
recording or otherwise, without prior written permission being secured.
Requests for permission to reproduce should be addressed to either ISO at the address below or ISO's
member body in the country of the requester.
ISO copyright office
Case postale 56 CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Reproduction may be subject to royalty payments or a licensing agreement.
Violators may be prosecuted.
©
ii ISO 2010 – All rights reserved
---------------------- Page: 8 ----------------------
oSIST prEN ISO 9693-1:2010
ISO/DIS 9693-1
Contents Page
Foreword . iv
Introduction . v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Requirements . 1
4.1 Biocompatibility . 1
4.2 Properties of metal-ceramic system . 1
5 Sampling . 2
5.1 Metallic material . 2
5.2 Ceramic . 2
6 Test methods . 2
6.1 Linear thermal expansion . 2
6.2 Glass transition temperature . 2
6.3 Young’s Modulus . 2
6.4 Metal-ceramic bond characterization (Schwickerath crack initiation test) .
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.