SIST EN ISO/IEC 7810:1998

Identification cards - Physical characteristics (ISO/IEC 7810:1995)

Specifies the general requirements for the design and the implementation of the interface equipment within the user's installation which connects to a microgrid or the generating part of a standalone system.

Identifikationskarten - Physikalische Eigenschaften (ISO/IEC 7810:1995)

Cartes d'identification - Caractéristiques physiques (ISO/IEC 7810:1995)

Identification cards - Physical characteristics (ISO/IEC 7810:1995)

General Information

• Status: Withdrawn
• Publication Date: 31-May-1998
• Withdrawal Date: 06-Dec-2020
• ICS: 35.240.15 - Identification cards. Chip cards. Biometrics
• Technical Committee: BFS - Banking and related financial services
• Current Stage: 9900 - Withdrawal (Adopted Project)
• Start Date: 04-Dec-2020
• Due Date: 27-Dec-2020
• Completion Date: 07-Dec-2020
• Directive: TP169 - Pravilnik o temeljnih kvalifikacijah za voznike motornih vozil v cestnem prometu
• Directive: TP205 - Pravilnik o gasilskih uniformah, oznakah, činih, opremi ter izkaznicah
• Directive: TP247 - Pravilnik o spremembah in dopolnitvah Pravilnika o upravljanju s čolni
• Ref Project: EN ISO/IEC 7810:1996 - Identification cards - Physical characteristics (ISO/IEC 7810:1995)

Relations

• Replaces: SIST EN 27816-2:1998 - Identification cards - Integrated circuit(s) with contacts - Part 2: Dimensions and location of the contacts (ISO 7816-2:1988, ed. 1)
• Effective Date: 01-Jun-1998

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO/IEC 7810:1998
01-junij-1998
1DGRPHãþD
SIST EN 27816-2:1998
Identification cards - Physical characteristics (ISO/IEC 7810:1995)
Identification cards - Physical characteristics (ISO/IEC 7810:1995)
Identifikationskarten - Physikalische Eigenschaften (ISO/IEC 7810:1995)
Cartes d'identification - Caractéristiques physiques (ISO/IEC 7810:1995)
Ta slovenski standard je istoveten z: EN ISO/IEC 7810:1996
ICS:
35.240.15 Identifikacijske kartice in Identification cards and
sorodne naprave related devices
SIST EN ISO/IEC 7810:1998 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO/IEC 7810:1998

---------------------- Page: 2 ----------------------

SIST EN ISO/IEC 7810:1998

---------------------- Page: 3 ----------------------

SIST EN ISO/IEC 7810:1998

---------------------- Page: 4 ----------------------

SIST EN ISO/IEC 7810:1998

---------------------- Page: 5 ----------------------

SIST EN ISO/IEC 7810:1998

---------------------- Page: 6 ----------------------

SIST EN ISO/IEC 7810:1998
ISO/IEC
INTERNATIONAL
STANDARD
Second edition
1995-08-I 5
Physical characteristics
Identification cards -
Cartes d’iden tifica tion - Caracte’ristiques physiques
Reference number
ISO/lEC 78103 995(E)

---------------------- Page: 7 ----------------------

SIST EN ISO/IEC 7810:1998
ISO/IEC 7810:1995(E)
Foreword
IS0 (the International Organization for Standardization) and IEC (the
International Electrotechnical Commission) form the specialized system for
worldwide standardization. National bodies that are members of IS0 or
IEC participate in the development of International Standards through
technical committees established by the respective organization to deal
with particular fields of technical activity. IS0 and IEC technical com-
mittees collaborate in fields of mutual interest. Other international organ-
izations, governmental and non-governmental, in liaison with IS0 and IEC,
also take part in the work.
In the field of information technology, IS0 and IEC have established a joint
technical committee, lSO/IEC JTC 1. Draft international Standards adopted
by the joint technical committee are circulated to the member bodies for
voting. Publication as an International Standard requires approval by at
least 75 % of the national bodies casting a vote.
International Standard lSO/IEC 7810 was prepared by Joint Technical
Committee lSO/IEC JTC 1, Information technology, Subcommittee SC 17,
lden tifica tion cards and related devices.
This second edition cancels and replaces the first edition (IS0 7810:1985),
of which it constitutes a technical revision.
0 lSO/lEC 1995
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced
or utilized in any form or by any means, electronic or mechanical, including protocopying and
microfilm, without permission in writing from the publisher.
lSO/IEC Copyright Office l Case postale 56 l CH-1211 Geneve 20 l Switzerland
Printed in Switzerland
ii

---------------------- Page: 8 ----------------------

SIST EN ISO/IEC 7810:1998
@ lSO/IEC ISO/IEC 7810:1995(E)
This International Standard is one of a series of standards describing the
parameters for identification cards as defined in clause 4 and the use of
such cards for international interchange.

---------------------- Page: 9 ----------------------

SIST EN ISO/IEC 7810:1998
This page intentionally left blank

---------------------- Page: 10 ----------------------

SIST EN ISO/IEC 7810:1998
ISO/IEC 7810:1995(E)
INTERNATIONAL STANDARD @ lSO/IEC
- Physical characteristics
Identification cards
subject to revision and parties to agreements based
1 Scope
on this International Standard are encouraged to
This International Standard specifies the physical investigate the possibility of applying the most recent
characteristics of identification cards including card editions of the standards indicated below. Members
construction, characteristics, and
materials, of IEC and IS0 maintain registers of currently valid
dimensions for three sizes of card. International Standards.
lSO/IEC 10373 specifies the test procedures used to
IS0 7816-I :I 987, Identification cards - Integrated
check cards against the parameters specified in this
circuit(s) cards with contacts - Part 7: Physical
International Standard.
characteristics.
This International Standard specifies the requirements
lSO/IEC 10373:1993, Identification cards - Test
for cards used for identification. It takes into
methods.
consideration both human and machine aspects and
states minimum requirements.
It is the purpose of this series of standards to provide
criteria to which cards shall perform, and methods of
4 Definition
testing. No consideration is given within these
standards to the amount of use, if any, experienced
For the purposes of this International Standard, the
by the card prior to the test. Failure to conform to
following definition applies.
specified criteria should be negotiated between the
involved parties.
4.1 identification card: Card identifying its holder
and issuer which may carry data required as input for
NOTE - Numeric values in the SI and/or Imperial
the intended use of the card and for transactions
measurement system in this International Standard may
based thereon.
have been rounded off and therefore are consistent with,
but not exactly equal to, each other. Either system may be
used, but the two should not be intermixed or reconverted.
The original design was made using the Imperial
measurement system.
5 Dimensions of card types
The nominal dimensions of the three sizes of card are
2 Conformance
shown in table 1.
An identification card is in conformance with this
Table 1 - Nominal dimensions
International Standard if it meets all mandatory
requirements specified herein.
Card Width Height Thickness
type
in in in
mm I I mm I
I mm I
3 Normative references
ID-l 85,60 3,370
53,98 2,125 0,76 0,030
The following standards contain provisions which,
ID-2 105,OO 4,134 74,00 2,913 0,76 0,030
through reference in this text, constitute provisions of
this International Standard. At the time of publication
ID-3 I125,OO 1 4,921 1 88,00 1 3,465 1 0,76 1 0,030 1
the editions indicated were valid. All standards are

---------------------- Page: 11 ----------------------

SIST EN ISO/IEC 7810:1998
@ lSO/IEC
ISO/IEC 7810:1995(E)
5.1 Card type ID-I
7 Card materials
The following dimensions and tolerances apply to
The card shall be made of PVC (polyvinyl chloride)
cards under the standard test atmosphere of 23 OC
and/or PVCA (polyvinyl chloride acetate) or materials
* 3 OC (73 OF * 5 OF) and 40 % to 60 % relative
having equal or better performance such as
humidity.
polyesters, polyethylenes and polycarbonates. Card
insert material may be used. They are not, however,
specified in this International Standard and shall not
51.1 Card width and height
interfere with other requirements specified in this
All points on the edges of the card in the finished
International Standard.
state, except for the rounded corners, shall fall
between two concentric, similarly aligned rectangles
WARNING - Rigid PVC and PVCA are sensitive to
which are dimensioned as follows:
the effects of plasticizers which may be
incorporated in some flexible plastic materials.
.
nembossed card,
Identification cards kept in contact with such
flexible plastics may soften, harden, or deform.
- Outer rectangle: width 85,72 mm (3,375 in)
height 54,03 mm (2,127 in)
- Inner rectangle: width 85,47 mm (3,365 in)
height 53,92 mm (2,123 in)
8 Card characteristics
See figure 1.
8.1 General
I
.
FUII~ emnos
...