SIST EN ISO 10438-3:2004
(Main)Petroleum, petrochemical and natural gas industries - Lubrication, shaft-sealing and control-oil systems and auxiliaries - Part 3: General-purpose oil systems (ISO 10438-3:2003)
Petroleum, petrochemical and natural gas industries - Lubrication, shaft-sealing and control-oil systems and auxiliaries - Part 3: General-purpose oil systems (ISO 10438-3:2003)
Migrated from Progress Sheet (TC Comment) (2000-07-10): Result of the splitting of WI 00012022 (CC/990921)
Erdöl-, petrochemische und Erdgasindustrie - Schmieröl-, Sperröl- und Regelölversorgungsanlagen und Hilfsanlagen - Teil 3: Ölversorgungsanlagen für allgemeine Anwendungsfälle (ISO 10438-3:2003)
Industries du pétrole, de la pétrochimie et du gaz naturel - Systemes de lubrification, systemes d'étanchéité, systemes d'huile de régulation et leurs auxiliaires - Partie 3: Systemes d'huile pour applications générales (ISO 10438-3:2003)
Petroleum, petrochemical and natural gas industries - Lubrication, shaft-sealing and control-oil systems and auxiliaries - Part 3: General-purpose oil systems (ISO 10438-3:2003)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 10438-3:2004
01-maj-2004
Petroleum, petrochemical and natural gas industries - Lubrication, shaft-sealing
and control-oil systems and auxiliaries - Part 3: General-purpose oil systems (ISO
10438-3:2003)
Petroleum, petrochemical and natural gas industries - Lubrication, shaft-sealing and
control-oil systems and auxiliaries - Part 3: General-purpose oil systems (ISO 10438-
3:2003)
Erdöl-, petrochemische und Erdgasindustrie - Schmieröl-, Sperröl- und
Regelölversorgungsanlagen und Hilfsanlagen - Teil 3: Ölversorgungsanlagen für
allgemeine Anwendungsfälle (ISO 10438-3:2003)
Industries du pétrole, de la pétrochimie et du gaz naturel - Systemes de lubrification,
systemes d'étanchéité, systemes d'huile de régulation et leurs auxiliaires - Partie 3:
Systemes d'huile pour applications générales (ISO 10438-3:2003)
Ta slovenski standard je istoveten z: EN ISO 10438-3:2003
ICS:
75.180.20
SIST EN ISO 10438-3:2004 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
EUROPEAN STANDARD
EN ISO 10438-3
NORME EUROPÉENNE
EUROPÄISCHE NORM
December 2003
ICS 75.180.20
English version
Petroleum, petrochemical and natural gas industries -
Lubrication, shaft-sealing and control-oil systems and auxiliaries
- Part 3: General-purpose oil systems (ISO 10438-3:2003)
Industries du pétrole, de la pétrochimie et du gaz naturel -
Systèmes de lubrification, systèmes d'étanchéité,
systèmes d'huile de régulation et leurs auxiliaires - Partie 3:
Systèmes d'huile pour applications générales (ISO 10438-
3:2003)
This European Standard was approved by CEN on 2 December 2003.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and United
Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2003 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 10438-3:2003 E
worldwide for CEN national Members.
---------------------- Page: 2 ----------------------
EN ISO 10438-3:2003 (E)
Foreword
This document (EN ISO 10438-3:2003) has been prepared by Technical Committee ISO/TC 67
"Materials, equipment and offshore structures for petroleum and natural gas industries" in
collaboration with Technical Committee CEN/TC 12 "Materials, equipment and offshore
structures for petroleum and natural gas industries", the secretariat of which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of
an identical text or by endorsement, at the latest by June 2004, and conflicting national
standards shall be withdrawn at the latest by June 2004.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of
the following countries are bound to implement this European Standard: Austria, Belgium, Czech
Republic, Denmark, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy,
Luxembourg, Malta, Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and
the United Kingdom.
NOTE FROM CMC The foreword is susceptible to be amended on reception of the German
language version. The confirmed or amended foreword, and when appropriate, the normative
annex ZA for the references to international publications with their relevant European
publications will be circulated with the German version.
Endorsement notice
The text of ISO 10438-3:2003 has been approved by CEN as EN ISO 10438-3:2003 without any
modifications.
2
---------------------- Page: 3 ----------------------
INTERNATIONAL ISO
STANDARD 10438-3
First edition
2003-12-15
Petroleum, petrochemical and natural gas
industries — Lubrication, shaft-sealing
and control-oil systems and auxiliaries —
Part 3:
General-purpose oil systems
Industries du pétrole, de la pétrochimie et du gaz naturel — Systèmes
de lubrification, systèmes d'étanchéité, systèmes d'huile de régulation
et leurs auxiliaires —
Partie 3: Systèmes d'huile pour applications générales
Reference number
ISO 10438-3:2003(E)
©
ISO 2003
---------------------- Page: 4 ----------------------
ISO 10438-3:2003(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2003
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2003 – All rights reserved
---------------------- Page: 5 ----------------------
ISO 10438-3:2003(E)
Contents Page
Foreword. iv
Introduction . v
1 Scope. 1
2 Normative references . 1
3 Terms, definitions and abbreviated terms. 1
4 Minimum components. 2
5 General. 2
6 Baseplates . 4
7 Oil reservoirs . 4
8 Pumps and drivers. 8
9 Coolers. 11
10 Filters. 13
11 Transfer valves. 15
12 Lube-oil rundown tanks. 15
13 Piping . 15
14 Instrumentation and electrical systems . 16
15 Inspection, testing, and preparation for shipment . 16
16 Vendor's data. 18
Annex A (informative) Typical schemas for general-purpose oil systems. 20
Annex B (informative) General-purpose oil system data sheets. 25
Annex C (informative) Inspector's check list. 33
Annex D (informative) Technical data for cost estimating of general-purpose oil systems . 36
Bibliography . 38
© ISO 2003 – All rights reserved iii
---------------------- Page: 6 ----------------------
ISO 10438-3:2003(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 10438-3 was prepared by Technical Committee ISO/TC 67, Materials, equipment and offshore structures
for petroleum, petrochemical and natural gas industries, Subcommittee SC 6, Processing equipment and
systems.
ISO 10438 consists of the following parts, under the general title Petroleum, petrochemical and natural gas
industries — Lubrication, shaft-sealing and control-oil systems and auxiliaries:
Part 1: General requirements
Part 2: Special-purpose oil systems
Part 3: General-purpose oil systems
Part 4: Self-acting gas seal support systems
iv © ISO 2003 – All rights reserved
---------------------- Page: 7 ----------------------
ISO 10438-3:2003(E)
Introduction
ISO 10438 is based on API Std 614, 4th edn., April 1999, divided into four parts as follows:
Part 1: General requirements is based on Chapter 1 of API Std 614;
Part 2: Special-purpose oil systems is based on Chapter 2 of API Std 614;
Part 3: General-purpose oil systems (this part) is based on Chapter 3 of API Std 614;
Part 4: Self-acting gas seal support systems is based on Chapter 4 of API Std 614.
Users of this part of ISO 10438 should be aware that further or differing requirements might be needed for
individual applications. This part of ISO 10438 is not intended to inhibit a vendor from offering, or the
purchaser from accepting alternative equipment or engineering solutions for the individual application. This
may be particularly appropriate where there is innovative or developing technology. Where an alternative is
offered, the vendor should identify any variations from this part of ISO 10438 and provide details.
This part of ISO 10438 requires the purchaser to specify certain details and features.
A bullet (•) at the beginning of a clause or subclause indicates that either a decision is required or further
information is to be provided by the purchaser. This information or decision should be indicated on suitable
data sheets; otherwise it should be stated in the quotation request (inquiry) or in the order.
© ISO 2003 – All rights reserved v
---------------------- Page: 8 ----------------------
INTERNATIONAL STANDARD ISO 10438-3:2003(E)
Petroleum, petrochemical and natural gas industries —
Lubrication, shaft-sealing and control-oil systems and
auxiliaries —
Part 3:
General-purpose oil systems
1 Scope
This part of ISO 10438 specifies requirements for oil systems supplying lubricating oil to machines in general-
purpose applications for use in the petroleum, petrochemical and natural gas industries as well as in other
industries by agreement. It is intended to be used in conjunction with ISO 10438-1. ISO 10438 in its entirety
specifies requirements for lubrication systems, oil-type shaft-sealing systems, self-acting gas seal systems,
control-oil systems and other auxiliaries for general- or special-purpose applications. These systems can
serve equipment such as compressors, gears, pumps and drivers. General-purpose applications are limited to
lubrication systems.
None of the parts of ISO 10438 is applicable to internal combustion engines.
Typical schemas for general-purpose oil systems are provided in Annex A.
NOTE General-purpose systems supply lubricating oil only (i.e. no seal oil) and do not require an accumulator to
cover transient conditions.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 10438-1:2003, Petroleum, petrochemical and natural gas industries — Lubrication, shaft-sealing and
control-oil systems and auxiliaries — Part 1: General requirements
ISO 14691, Petroleum and natural gas industries — Flexible couplings for mechanical power transmission —
General purpose applications
IEC 60079 (all parts), Electrical apparatus for explosive gas atmospheres
3 Terms, definitions and abbreviated terms
For the purposes of this document, the terms, definitions and abbreviated terms given in ISO 10438-1 apply.
© ISO 2003 – All rights reserved 1
---------------------- Page: 9 ----------------------
ISO 10438-3:2003(E)
4 Minimum components
The bill of material covered below describes the minimum specified system. Manufacturers may substitute
alternatives for any of the options covered in this clause as upgrades to the basic system if required or if
offered as standard for the equipment serviced. In any event, the oil system supplied shall be capable of
supplying sufficient quantities of clean, filtered oil at proper temperature and pressure for start-up and all
operating conditions of the serviced rotating equipment.
The basic oil system shall contain as a minimum the following components:
a) single pump, (cast iron or steel casing) which may be shaft-driven or motor driven;
b) motor driven start-up pump (if required);
c) valves, made of carbon steel with stainless steel trim;
d) oil piping, made of stainless steel with carbon steel slip-on flanges, conforming to the piping system
design code (e.g. ASME B31.3), or stainless steel tubing and fittings;
e) reservoir, made of stainless steel with minimum 3 min retention time, or combined with equipment base;
f) single cooler;
g) single filter with 25 µm nominal pore size;
h) single regulator for control of delivered oil pressure;
i) the following instruments:
1) pressure indicator (PI),
2) temperature indicator (TI),
3) visual level indicator (LI),
4) pressure switch low-low (PSLL).
5 General
5.1 The equipment (including auxiliaries) covered by this part of ISO 10438 shall be designed and
constructed for a minimum service life of 20 years. It is recognized that this is a design criterion.
5.2 The oil system shall be suitable for general-purpose applications as defined in ISO 10438-1. The
system shall be designed as a separate console, or may be designed to be integral with the baseplate of the
equipment it serves. If components are spared, the design shall allow for transfer between and shutdown of
the main and spared components of the system for maintenance without interrupting the operation of the
system or the equipment the system serves.
5.3 The vendor shall assume unit responsibility for all equipment and all auxiliary systems included in the
scope of the order.
5.4 The materials of construction of all major components shall be clearly stated in the vendor's proposal.
Materials shall be identified by reference to applicable international or national standards including the
material grade.
5.5 The purchaser shall specify the required oil supply conditions and the heat load.
2 © ISO 2003 – All rights reserved
---------------------- Page: 10 ----------------------
ISO 10438-3:2003(E)
z 5.6 Control of the sound pressure level (SPL) of all equipment furnished shall be a joint effort of the
purchaser and the vendor. The equipment furnished by the vendor shall conform to the maximum allowable
sound pressure level specified by the purchaser.
5.7 Where oil is supplied from a common system to two or more machines (such as a compressor, a gear,
and a motor), the oil's characteristics shall be specified on the data sheets (such as provided in Annex B) on
the basis of mutual agreement with all vendors supplying equipment served by the common oil system.
NOTE The usual lubricant employed in a common oil system is a hydrocarbon oil of viscosity grade 32 or 46 as
specified in ISO 8068.
5.8 The system shall be designed to supply oil to all equipment specified by the purchaser.
5.9 Oil recycled for control purposes shall originate upstream of the filters.
NOTE This is to minimize the potential for generation of static electricity (or a static charge) that can result when
filtered oil bypasses the equipment and is recycled directly to the reservoir.
z 5.10 The purchaser shall specify whether the installation is indoors (heated or unheated) or outdoors (with or
without a roof) as well as the weather and environmental conditions in which the equipment will operate
(including maximum and minimum temperatures and unusual humidity, dust, or corrosion conditions).
z 5.11 If specified, the arrangement of the equipment, including piping and auxiliaries, shall be developed
jointly by the purchaser and the vendor. The arrangement shall provide adequate clearance areas and safe
access for operation and maintenance.
NOTE For some pre-engineered general-purpose oil systems, purchaser input might be impractical.
z 5.12 If applicable, the purchaser shall specify minimum requirements for clearance around and access to
components (especially clearance around and access to coolers, filters, and hand valves).
5.13 Motors, electrical components, and electrical installations shall be suitable for the area classification
(class, group, and division or zone) specified on the data sheets and shall meet the requirements of the
applicable part(s) of IEC 60079 as well as local codes specified and furnished by the purchaser (see
ISO 10438-1).
z 5.14 If specified, pumps, filters, strainers, coolers, traps, valves, and all other components that retain oil
under pressure and that are external to the reservoir shall be made of steel.
5.15 Unless otherwise specified, components may be submerged in the reservoir, and these may be made
of cast iron.
z 5.16 If specified, valved vents, drains, and piping shall be furnished to permit draining, cleaning, and refilling
of idle components while the equipment is in operation.
5.17 Coolers, filters, overhead rundown tanks, and other pressure vessels within the scope of the pressure
design code shall conform to the requirements of that code.
5.18 The vendor shall advise the purchaser of, and both parties shall mutually agree upon, any special
provisions that are necessary to ensure that an adequate supply of lube oil is maintained in the event of
complete failure of the lube-oil supply system. These provisions may include stand-by pumps, rundown tanks,
and special arrangements for equipment safety and protection when the equipment decelerates. Provisions
shall be adequate for coast-down time and cool-off time as applicable. The purchaser and the vendor shall
mutually agree upon the system and its components.
5.19 Block valves which interrupt the oil flow to the equipment shall not be installed in oil supply lines
downstream of the filters unless the block valves are part of a component block and bypass arrangement.
© ISO 2003 – All rights reserved 3
---------------------- Page: 11 ----------------------
ISO 10438-3:2003(E)
5.20 Welding of piping and pressure-containing parts, as well as any dissimilar-metal welds and weld repairs,
shall be performed in accordance with the pressure design code or the piping system design code as
applicable.
5.21 When components, which may require later removal for maintenance, are installed using screwed
connections, the connecting piping shall be provided with flanges such that the component may be removed
without requiring cutting pipe or major disassembly of the unit.
6 Baseplates
6.1 The major components (pumps, filters, coolers, and reservoir) shall be mounted directly on structural
steel as a separate console or integrated with the equipment base.
6.2 Unless otherwise specified, console baseplates shall be of the drip-rim type with one or more drain
connections at least DN40 (NPS 1 1/2) in size. Baseplates, mounted components, and decking shall be
arranged and installed to ensure drainage and avoid the retention of liquid.
6.3 The baseplate shall be provided with lifting lugs for at least a four-point lift. The baseplate shall be
designed so that after the components and all piping mounted on it are drained of oil, the package can be
lifted without permanently distorting or otherwise damaging either the baseplate or any component mounted
on it.
z 6.4 If specified, metal decking covering all walk and work areas shall be provided on the top of the
baseplate. If furnished, metal decking shall be non-skid.
z 6.5 If specified, baseplates shall be suitable for grouting.
z 6.6 If specified, the baseplate shall be suitable for column mounting (that is, of sufficient rigidity to be
supported at specified points) without continuous grouting under structural members. The baseplate design
shall be mutually agreed upon by the purchaser and the vendor.
z 6.7 If specified, all welding other than that covered by the pressure design code or the piping system design
code, such as welding on baseplates, non-pressure ducting, lagging, and control panels, shall be performed in
accordance with a structural welding standard (e.g. AWS D1.1).
6.8 The bottom of the baseplate between structural members shall be open. When the baseplate is
installed on a concrete foundation and grouted as specified in 6.5, accessibility for grouting under all load-
carrying structural members shall be provided.
7 Oil reservoirs
7.1 General
Reservoirs shall be separate or combined with the equipment baseplate, and they shall be rigid enough to
prevent sagging and vibration. Components bolted to the reservoir shall be mounted on pads; no bolt holes
shall extend into the reservoir.
7.2 Protection from dirt and water
Reservoirs shall be sealed to prevent dirt and water from entering. Top-surface openings shall be raised at
least 6 mm (1/4 in) and shall have a gasket. When pumps, coolers, or filters are mounted on top of the
reservoir, the reservoir top shall be provided with a drain rim or gutter and one or more drain connections.
4 © ISO 2003 – All rights reserved
---------------------- Page: 12 ----------------------
ISO 10438-3:2003(E)
7.3 Oil connections and internal piping
7.3.1 All oil return flow streams shall be hydraulically located as far away from the pump suction
connections as possible.
NOTE The use of the term “hydraulically located as far away” is intended to convey the concept that return flow
streams can be directed by internal piping or baffling to avoid disturbing the oil flow at pump inlets. This internal piping or
baffling could be used in lieu of external connections physically located such a distance from the pump suctions that they
avoid disturbing the oil flow at the pump inlets.
7.3.2 All atmospheric oil return connections (including fill connections) shall be located above the maximum
operating level and shall transport oil (via open-top stilling tubes or degassing trays). Stilling tubes shall have
bottom baffles.
7.3.3 Pump suction connections shall be located at least 50 mm (2 in) above the reservoir bottom.
7.3.4 Reservoir pipe connections DN40 (NPS 1 1/2) and larger shall be flanged.
7.4 Manways and drains
7.4.1 Each reservoir shall be furnished with a valved drain connection.
7.4.2 Manway openings shall be provided which will permit unobstructed access for inspection and cleaning
of all interior compartments. Manways shall be located on top of the reservoir and if entry is required for
cleaning each manway shall be at least 600 mm × 600 mm (24 in × 24 in). If access is not required for
cleaning, a minimum 150 mm (6 in) diameter opening shall be provided.
z 7.4.3 If specified, to ensure complete drainage, the bottom of each reservoir shall be sloped to a low point
drain.
z 7.4.4 If specified, a flanged drain connection (with a valve and a blind flange) at least 50 mm (2 in) in size
shall be provided.
7.5 Features and appendages
z 7.5.1 The oil reservoir shall have the following features and appendages:
a) the capacity to settle moisture and foreign matter adequately and to provide allowance for rundown from
the entire system;
b) provisions to eliminate air and minimize migration of foreign matter to each pump suction;
c) a reservoir level indicator such as a dipstick, level gauge, or bull’s eye;
d) if specified, an oil level glass arranged to cover the span from at least 25 mm (1 in) above the rundown
level to 50 mm (2 in) below the pump suction-loss level. The oil level glass shall be located as far away as
possible from the oil return lines and be visible from the perimeter of the unit. The maximum and
minimum operating levels, rundown level, and suction-loss level shall be indicated on the glass. If more
than one level glass is provided, they shall be offset. The top glass shall be of the weld pad type;
e) a weatherproof, corrosion-resistant filter-breather cap at least 50 mm (2 in) in size (this connection may
also be used as a fill opening);
f) if specified, a fill opening at least 50 mm (2 in) in size which automatically closes (normally held shut by a
spring) and is equipped with a stainless steel fine-mesh strainer basket that has an open area equal to
200 % of the internal pipe area;
g) internal baffles that are not gas-tight;
© ISO 2003 – All rights reserved 5
---------------------- Page: 13 ----------------------
ISO 10438-3:2003(E)
h) Individual non-pressurized reservoir return lines that enter the reservoir above the rundown level
(see 7.6.1.1);
i) if specified, a low-level alarm which actuates at the minimum operating.
7.6 Capacity and configurations
7.6.1 Definitions of levels
7.6.1.1 The rundown level (1 in Figure 1) is the highest level that oil in the reservoir may reach when the
entire system is shut down.
7.6.1.2 The maximum operating level (2 in Figure 1) is the highest level that oil will reach during normal
operation of the equipment.
7.6.1.3 The minimum operating level (3 in Figure 1) is the lowest level that oil will reach during normal
operation of the equipment.
7.6.1.4 The suction-loss level (4 in Figure 1) is the level at which the pump begins to lose prime. The
pump suction level is defined by the pump suction vortex and net positive suction head requirements.
7.6.1.5 The charge capacity is the total volume below the rundown level.
7.6.1.6 The normal operating range is any level between the maximum and minimum operating levels.
7.6.1.7 The retention capacity is the total volume below the minimum operating level.
7.6.1.8 Retention time is the time allowed for disengagement of entrained air or gas.
7.6.1.9 The rundown capacity is the volume between the rundown level and the maximum operating level.
7.6.1.10 The working capacity is the volume between the minimum operating level and the suc
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.