SIST EN 4119:2004
(Main)Aerospace series - Nuts, bihexagonal, self-locking, deep counterbored, in heat resisting steel FE-PA92HT (A286), silver plated on thread - Classification: 1 100 MPa (at ambient temperature) / 650°C
Aerospace series - Nuts, bihexagonal, self-locking, deep counterbored, in heat resisting steel FE-PA92HT (A286), silver plated on thread - Classification: 1 100 MPa (at ambient temperature) / 650°C
This standard specifies the characteristics of self-locking bihexagonal nuts with deep counterbore in FE-PA92HT, silver plated on thread, for aerospace applications.
Classification: 1 100 MPa ) I 650 °C )
Aerospace series - Nuts, bihexagonal, self-locking, deep counterbored, in heat resisting steel FE-PA92HT (A286), silver plated on thread - Classification: 1 100 MPa (at ambient temperature) / 650°C
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Aerospace series - Nuts, bihexagonal, self-locking, deep counterbored, in heat resisting steel FE-PA92HT (A286), silver plated on thread - Classification: 1 100 MPa (at ambient temperature) / 650°CAerospace series - Nuts, bihexagonal, self-locking, deep counterbored, in heat resisting steel FE-PA92HT (A286), silver plated on thread - Classification: 1 100 MPa (at ambient temperature) / 650°C49.030.30MaticeNutsICS:Ta slovenski standard je istoveten z:EN 4119:2003SIST EN 4119:2004en01-maj-2004SIST EN 4119:2004SLOVENSKI
STANDARD
SIST EN 4119:2004
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 4119January 2003ICS 49.030.30English versionAerospace series - Nuts, bihexagonal, self-locking, deepcounterbored, in heat resisting steel FE-PA92HT (A286), silverplated on thread - Classification: 1 100 MPa (at ambienttemperature) / 650°CThis European Standard was approved by CEN on 2 June 2002.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,Hungary, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and UnitedKingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2003 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 4119:2003 ESIST EN 4119:2004
EN 4119:2003 (E)2ContentspageForeword.31Scope.32Normative references.33Required characteristics.43.1Configuration - Dimensions - Tolerances – Masses.43.2Materials.43.3Surface treatment.44Designation.65Marking.66Technical specification.6SIST EN 4119:2004
EN 4119:2003 (E)3ForewordThis document (EN 4119:2003) has been prepared by the European Association of Aerospace Manufacturers –Standardization (AECMA-STAN).Afte
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.