SIST EN ISO 13257:2018
(Main)Thermoplastics piping systems for non-pressure applications - Test method for resistance to elevated temperature cycling (ISO 13257:2010)
Thermoplastics piping systems for non-pressure applications - Test method for resistance to elevated temperature cycling (ISO 13257:2010)
ISO 13257:2010 specifies a method for testing the resistance of thermoplastics piping systems for soil and waste discharge inside buildings, application area "B", or buried in the ground within the building structure, application areas "BD" or "UD", to 1 500 cycles of elevated temperature cycling.
Rohrleitungssysteme aus Thermoplasten für drucklose Anwendungen - Prüfverfahren für die Temperaturbeanspruchbarkeit (ISO 13257:2010)
Systèmes de canalisations thermoplastiques pour applications sans pression - Méthode d'essai de résistance à des cycles de température élevée (ISO 13257:2010)
L'ISO 13257:2010 spécifie une méthode d'essai de résistance des systèmes de canalisations thermoplastiques pour l'évacuation des eaux usées et eaux-vannes à l'intérieur des bâtiments, zone d'application «B», ou enterrées sous le bâtiment, zones d'application «BD» ou «UD», à 1 500 cycles à une température élevée.
Plastomerni cevni sistemi, ki delujejo po težnostnem principu - Metoda za preskus odpornosti proti zvišani temperaturi (ISO 13257:2010)
Standard ISO 13257:2010 določa metodo za preskušanje odpornosti plastomernih cevnih odvodnih sistemov v zgradbah (območje uporabe »B«) ali vkopanih v zemljo znotraj stavbne konstrukcije (območje uporabe »BD« ali »UD«), ko so izpostavljeni 1500 ciklom krožeče povišane temperature.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 13257:2018
01-januar-2018
1DGRPHãþD
SIST EN 1055:1997
Plastomerni cevni sistemi, ki delujejo po težnostnem principu - Metoda za preskus
odpornosti proti zvišani temperaturi (ISO 13257:2010)
Thermoplastics piping systems for non-pressure applications - Test method for
resistance to elevated temperature cycling (ISO 13257:2010)
Rohrleitungssysteme aus Thermoplasten für drucklose Anwendungen - Prüfverfahren für
die Temperaturbeanspruchbarkeit (ISO 13257:2010)
Systèmes de canalisations thermoplastiques pour applications sans pression - Méthode
d'essai de résistance à des cycles de température élevée (ISO 13257:2010)
Ta slovenski standard je istoveten z: EN ISO 13257:2017
ICS:
23.040.20 Cevi iz polimernih materialov Plastics pipes
SIST EN ISO 13257:2018 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 13257:2018
---------------------- Page: 2 ----------------------
SIST EN ISO 13257:2018
EN ISO 13257
EUROPEAN STANDARD
NORME EUROPÉENNE
October 2017
EUROPÄISCHE NORM
ICS 23.040.20; 91.140.80 Supersedes EN 1055:1996
English Version
Thermoplastics piping systems for non-pressure
applications - Test method for resistance to elevated
temperature cycling (ISO 13257:2010)
Systèmes de canalisations thermoplastiques pour Rohrleitungssysteme aus Thermoplasten für drucklose
applications sans pression - Méthode d'essai de Anwendungen - Prüfverfahren für die
résistance à des cycles de température élevée (ISO Temperaturbeanspruchbarkeit (ISO 13257:2010)
13257:2010)
This European Standard was approved by CEN on 19 September 2017.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2017 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 13257:2017 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 13257:2018
EN ISO 13257:2017 (E)
Contents Page
European Foreword . 3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 13257:2018
EN ISO 13257:2017 (E)
European Foreword
The text of ISO 13257:2010 has been prepared by Technical Committee ISO/TC 138 “Plastics pipes,
fittings and valves for the transport of fluids” of the International Organization for Standardization
(ISO) and has been taken over as EN ISO 13257:2017 by Technical Committee CEN/TC 155 “Plastics
piping systems and ducting systems” the secretariat of which is held by NEN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by April 2018 and conflicting national standards shall be
withdrawn at the latest by October 2020.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 1055:1996.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia,
Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands,
Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
the United Kingdom.
Endorsement notice
The text of ISO 13257:2010 has been approved by CEN as a EN ISO 13257:2017 without any
modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 13257:2018
---------------------- Page: 6 ----------------------
SIST EN ISO 13257:2018
INTERNATIONAL ISO
STANDARD 13257
First edition
2010-06-01
Thermoplastics piping systems for non-
pressure applications — Test method for
resistance to elevated temperature
cycling
Systèmes de canalisations thermoplastiques pour applications sans
pression — Méthode d'essai de résistance à des cycles de température
élevée
Reference number
ISO 13257:2010(E)
©
ISO 2010
---------------------- Page: 7 ----------------------
SIST EN ISO 13257:2018
ISO 13257:2010(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
COPYRIGHT PROTECTED DOCUMENT
© ISO 2010
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2010 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 13257:2018
ISO 13257:2010(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 13257 was prepared by Technical Committee ISO/TC 138, Plastics pipes, fittings and valves for the
transport of fluids, Subcommittee SC 1, Plastics pipes and fittings for soil, waste and drainage (including land
drainage).
© ISO 2010 – All rights reserved iii
---------------------- Page: 9 ----------------------
SIST EN ISO 13257:2018
---------------------- Page: 10 ----------------------
SIST EN ISO 13257:2018
INTERNATIONAL STANDARD ISO 13257:2010(E)
Thermoplastics piping systems for non-pressure
applications — Test method for resistance to elevated
temperature cycling
1 Scope
This International Standard specifies a method for testing the resistance of thermoplastics piping systems for
soil and waste discharge inside buildings, application area “B”, or buried in the ground within the building
structure, application areas “BD” or “UD”, to 1 500 cycles of elevated temperature cycling.
NOTE This method assesses leaktightness and resistance to sagging.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO/TS 7024, Plastics piping systems for soil and waste discharge (low and high temperature) inside
buildings — Thermoplastics — Recommended practice for installation
3 Terms and definitions, and symbols
3.1 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
3.1.1
nominal outside diameter
d
n
specified diameter assigned to a nominal size (DN/OD or DN/ID)
NOTE It is expressed in millimetres.
3.1.2
expansion gap
E
distance between the bottom of a socket and the spigot of the inserted component allowing expansion of the
system
NOTE Adapted from ISO/TS 7024:2005, def
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.