B08.04 - Precious Metal Coatings

ABSTRACT
This specification covers the requirements for electrodeposited rhodium coatings for engineering applications, usually employed for their corrosion resistance, stable electrical contact resistance, wear resistance, reflectivity, and heat resistance. Coating shall be classified based on their thickness. Specimens shall undergo preparatory preplating procedures such as surface cleaning and stress relief treatment, as well as post-plating embrittlement relief process. Coatings shall be sampled, tested, and conform accordingly to specified requirements as to purity, appearance, adhesion, hydrogen embrittlement, reflectivity, and thickness (to be measured either nondestructively by beta backscatter method or X-ray fluorescence, or destructively by microscopical cross sectioning method).
SCOPE
1.1 This specification covers requirements for electrodeposited coatings of rhodium used for engineering purposes.  
1.2 Coatings of rhodium covered by this specification are usually employed for their corrosion resistance, stable electrical contact resistance, wear resistance, reflectivity, and heat resistance.  
1.3 Appendix X1 covers some typical applications for electrodeposited rhodium.  
1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification establishes the requirements for electrodeposited palladium coatings for use in engineering applications. This specification also covers composite coatings of palladium with a thin gold overplate for applications involving electrical contacts. The plating system shall indicate the basis metal involved, thickness of the underplates, thickness of the palladium coating, and grade of the gold overplate. Coatings shall be sampled, tested, and conform accordingly to specified requirements as to purity, appearance, thickness, dutility, adhesion (to be examined either by bend, heat, or cutting test), and integrity (gross defects, mechanical damage, and porosity).
SCOPE
1.1 This specification covers requirements for electrodeposited palladium coatings containing at least 99.7 mass % of palladium metal. Composite coatings consisting of palladium with a thin gold overplate for applications involving electrical contacts are also covered.  
1.2 Properties—Palladium is the lightest and least noble of the platinum group metals. It has a specific gravity of 12.0, which is substantially less than gold (19.3) and platinum (21.5). This yields a greater volume or thickness of coating and, consequently, some saving of metal weight accompanied by a small sacrifice in corrosion resistance and reflectivity. The following table compares the hardness range of electrodeposited palladium with other electrodeposited noble metals and alloys (1,2).2    
Approximate Hardness (HK25)    
Gold  
50–250  
Palladium  
75–600  
Platinum  
150–550  
Palladium-Nickel  
300–650  
Rhodium  
750–1100  
Ruthenium  
600–1300  
1.3 The values stated in SI units are the preferred values. Values provided in parentheses are for information only.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification establishes the requirements for electrodeposited silver coatings that may be mat, bright, or semibright, and are usually employed as solderable surfaces and for their electrical contact characteristics, high electrical and thermal conductivity, thermocompression bonding, wear resistance on load-bearing surfaces, and spectral reflectivity. Coatings shall be classified into types according to minimum purity, grade according to surface appearance (bright, semibright, or mat), and class according to whether any surface treatment has been applied. Coatings shall undergo preplating operations such as stress relief treatment, strike, and underplating, as well as post-plating embrittlement relief. Coatings shall be sampled, tested, and conform accordingly to specified requirements as to nature, purity, appearance, defects, adhesion, solderability, hardness, spectral reflectance, electrical conductivity, hydrogen embrittlement relief, and thickness (measured either nondestructively by beta backscatter, X-ray spectrometry, or magnetic method, or destructively by coulometric technique or microscopical cross-sectioning procedure).
SCOPE
1.1 This specification covers requirements for electrodeposited coatings of silver used for engineering purposes that may be matt, bright, or semibright and are not less than 98 % silver purity.  
1.2 Coatings of silver covered by this specification are usually employed for solderable surfaces, electrical contact characteristics, high electrical and thermal conductivity, thermocompression bonding, wear resistance of load-bearing surfaces, and spectral reflectivity.  
1.3 In the Appendixes, important characteristics of electrodeposited silver coatings are briefly described which must be considered when used in engineering applications, namely electrical conductivity (see Appendix X1), silver migration (see Appendix X2), thickness (see Appendix X3), hardness (see Appendix X4), and atmospheric tarnish (see Appendix X5).  
1.4 The following hazards caveat pertains only to the test methods section of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification covers requirements for electrodeposited palladium-cobalt alloy coatings containing approximately 80% of palladium and 20% of cobalt. It also covers composite coatings consisting of palladium-cobalt with a thin gold overplate for applications involving electrical contacts. Palladium and palladium-cobalt remain competitive finishes for high reliability applications. The specification deals with material classification, ordering information, materials and manufacture, coating requirements, sampling, test methods, special government requirements, and other requirements.
SCOPE
1.1 This specification covers requirements for electrodeposited palladium-cobalt alloy coatings containing approximately 80 % of palladium and 20 % of cobalt. Composite coatings consisting of palladium-cobalt with a thin gold overplate for applications involving electrical contacts are also covered. Palladium and palladium-cobalt remain competitive finishes for high reliability applications.  
1.2 Properties—Palladium is the lightest and least noble of the platinum group metals (1)2. It has the density of 12 gm per cubic centimeter, specific gravity of 12.0, that is substantially lower than the density of gold, 19.29 gm per cubic centimeter, specific gravity 19.3, and platinum 21.48 gm per cubic centimeter, specific gravity 21.5. The density of cobalt on the other hand is even less than palladium. It is only 8.69 gm per cubic centimeter, specific gravity 8.7. This yields a greater volume or thickness of coating and, consequently, some saving of metal weight and reduced cost. Palladium-cobalt coated surfaces provide a hard surface finish (Test Methods E18), thus decreasing wear and increasing durability. Palladium-cobalt coated surfaces also have a very low coefficient of friction 0.43 compared to hard gold 0.60, thus providing lower mating and unmating forces for electrical contacts (1). Palladium-cobalt has smaller grain size (Test Methods E112), 50 – 150 Angstroms, compared to Hard Gold 200 – 250 Angstroms (1), or 5 – 15 nanometer, compared to hard gold 20 – 25 nanometer (1). Palladium-cobalt has low porosity (Test Method B799) 0.2 porosity index compared to hard gold 3.7 porosity index (1). Palladium-cobalt coated surfaces have high ductility (Practice B489) 3-7 % compared to that of hard gold 1). The palladium-cobalt coated surface is also thermally more stable 395 °C than hard gold 150 °C, and silver 170 °C. The following Table 1 compares the hardness range of electrodeposited palladium-cobalt with other electrodeposited noble metals and alloys (2, 3).  
1.3 Units—The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification establishes the requirements for electrodeposited gold coatings for engineering applications, employed specifically for their corrosion and tarnish resistance (including resistance to fretting corrosion and catalytic polymerization), bondability, low and stable contact resistance, solderability, and infrared reflectivity. This specification does not cover gold coatings produced from autocatalytic, immersion, and vapor deposition. Coatings shall be classified into types, which characterize minimum purity, and codes, which designate Knoop hardness. Coatings shall be sampled, tested and conform to specified requirements as to purity, hardness, appearance, thickness, mass per unit area, ductility, adhesion (assessed by either bend, heat, or cutting test), and integrity (including gross defects, mechanical damage, and porosity).
SCOPE
1.1 This specification covers requirements for electrodeposited gold coatings that contain not less than 99.00 mass % gold and that are used for engineering applications.  
1.2 Specifically excluded from this specification are autocatalytic, immersion, and vapor deposited gold coatings.  
1.3 Gold coatings conforming to this specification are employed for their corrosion and tarnish resistance (including resistance to fretting corrosion and catalytic polymerization), bondability, low and stable contact resistance, solderability, and infrared reflectivity. Several types of coatings, differing in gold purity and hardness, are covered by this specification.  
1.4 The values stated in SI units are to be regarded as the standard. Values provided in parentheses are for information only.  
1.5 The following hazards caveat pertains only to the test methods section, Section 9, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification establishes the requirements for electrodeposited palladium coatings for use in engineering applications. This specification also covers composite coatings of palladium with a thin gold overplate for applications involving electrical contacts. The plating system shall indicate the basis metal involved, thickness of the underplates, thickness of the palladium coating, and grade of the gold overplate. Coatings shall be sampled, tested, and conform accordingly to specified requirements as to purity, appearance, thickness, dutility, adhesion (to be examined either by bend, heat, or cutting test), and integrity (gross defects, mechanical damage, and porosity).
SCOPE
1.1 This specification covers requirements for electrodeposited palladium coatings containing at least 99.7 mass % of palladium metal. Composite coatings consisting of palladium with a thin gold overplate for applications involving electrical contacts are also covered.  
1.2 Properties—Palladium is the lightest and least noble of the platinum group metals. It has a specific gravity of 12.0, which is substantially less than gold (19.3) and platinum (21.5). This yields a greater volume or thickness of coating and, consequently, some saving of metal weight accompanied by a small sacrifice in corrosion resistance and reflectivity. The following table compares the hardness range of electrodeposited palladium with other electrodeposited noble metals and alloys (1,2).2    
Approximate Hardness (HK25)    
Gold  
50–250  
Palladium  
75–600  
Platinum  
150–550  
Palladium-Nickel  
300–650  
Rhodium  
750–1100  
Ruthenium  
600–1300  
1.3 The values stated in SI units are the preferred values. Values provided in parentheses are for information only.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ABSTRACT
This specification covers the requirements for electrodeposited rhodium coatings for engineering applications, usually employed for their corrosion resistance, stable electrical contact resistance, wear resistance, reflectivity, and heat resistance. Coating shall be classified based on their thickness. Specimens shall undergo preparatory preplating procedures such as surface cleaning and stress relief treatment, as well as post-plating embrittlement relief process. Coatings shall be sampled, tested, and conform accordingly to specified requirements as to purity, appearance, adhesion, hydrogen embrittlement, reflectivity, and thickness (to be measured either nondestructively by beta backscatter method or X-ray fluorescence, or destructively by microscopical cross sectioning method).
SCOPE
1.1 This specification covers requirements for electrodeposited coatings of rhodium used for engineering purposes.  
1.2 Coatings of rhodium covered by this specification are usually employed for their corrosion resistance, stable electrical contact resistance, wear resistance, reflectivity, and heat resistance.  
1.3 Appendix X1 covers some typical applications for electrodeposited rhodium.  
1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ABSTRACT
This specification covers the requirements for electrodeposited rhodium coatings for engineering applications, usually employed for their corrosion resistance, stable electrical contact resistance, wear resistance, reflectivity, and heat resistance. Coating shall be classified based on their thickness. Specimens shall undergo preparatory preplating procedures such as surface cleaning and stress relief treatment, as well as post-plating embrittlement relief process. Coatings shall be sampled, tested, and conform accordingly to specified requirements as to purity, appearance, adhesion, hydrogen embrittlement, reflectivity, and thickness (to be measured either nondestructively by beta backscatter method or X-ray fluorescence, or destructively by microscopical cross sectioning method).
SCOPE
1.1 This specification covers requirements for electrodeposited coatings of rhodium used for engineering purposes.  
1.2 Coatings of rhodium covered by this specification are usually employed for their corrosion resistance, stable electrical contact resistance, wear resistance, reflectivity, and heat resistance.  
1.3 Appendix X1 covers some typical applications for electrodeposited rhodium.  
1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ABSTRACT
This specification establishes the requirements for electrodeposited silver coatings that may be mat, bright, or semibright, and are usually employed as solderable surfaces and for their electrical contact characteristics, high electrical and thermal conductivity, thermocompression bonding, wear resistance on load-bearing surfaces, and spectral reflectivity. Coatings shall be classified into types according to minimum purity, grade according to surface appearance (bright, semibright, or mat), and class according to whether any surface treatment has been applied. Coatings shall undergo preplating operations such as stress relief treatment, strike, and underplating, as well as post-plating embrittlement relief. Coatings shall be sampled, tested, and conform accordingly to specified requirements as to nature, purity, appearance, defects, adhesion, solderability, hardness, spectral reflectance, electrical conductivity, hydrogen embrittlement relief, and thickness (measured either nondestructively by beta backscatter, X-ray spectrometry, or magnetic method, or destructively by coulometric technique or microscopical cross-sectioning procedure).
SCOPE
1.1 This specification covers requirements for electrodeposited coatings of silver used for engineering purposes that may be mat, bright, or semibright and are not less than 98 % silver purity.  
1.2 Coatings of silver covered by this specification are usually employed for solderable surfaces, electrical contact characteristics, high electrical and thermal conductivity, thermocompression bonding, wear resistance of load-bearing surfaces, and spectral reflectivity.  
1.3 In the Appendixes important characteristics of electrodeposited silver coatings are briefly described which must be considered when used in engineering applications, namely electrical conductivity (see Appendix X1), silver migration (see Appendix X2), thickness (see Appendix X3), hardness (see Appendix X4), and atmospheric tarnish (see Appendix X5).  
1.4 The following hazards caveat pertains only to the test methods section of this specification:  This standard does not purport to address the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ABSTRACT
This specification covers requirements for electrodeposited palladium-cobalt alloy coatings containing approximately 80% of palladium and 20% of cobalt. It also covers composite coatings consisting of palladium-cobalt with a thin gold overplate for applications involving electrical contacts. Palladium and palladium-cobalt remain competitive finishes for high reliability applications. The specification deals with material classification, ordering information, materials and manufacture, coating requirements, sampling, test methods, special government requirements, and other requirements.
SCOPE
1.1 This specification covers requirements for electrodeposited palladium-cobalt alloy coatings containing approximately 80% of palladium and 20% of cobalt. Composite coatings consisting of palladium-cobalt with a thin gold overplate for applications involving electrical contacts are also covered. Palladium and palladium-cobalt remain competitive finishes for high reliability applications.  
1.2 Properties—Palladium is the lightest and least noble of the platinum group metals (1)2. IIt has the density of 12 gm per cubic centimeter, specific gravity of 12.0, that is substantially lower than the density of gold, 19.29 gm per cubic centimeter, specific gravity 19.3, and platinum 21.48 gm per cubic centimeter, specific gravity 21.5. The density of cobalt on the other hand is even less than palladium. It is only 8.69 gm per cubic centimeter, specific gravity 8.7. This yields a greater volume or thickness of coating and, consequently, some saving of metal weight and reduced cost. Palladium-cobalt coated surface provides a hard surface finish (ASTM E18) thus decreasing wear and increasing durability. Palladium-cobalt coated surface also has very low coefficient of friction 0.43 compared to hard gold 0.60 thus providing lower mating and unmating forces for electrical contacts (1) 2. Palladium-cobalt has smaller grain size (ASTM E112), 50 – 150 Angstroms, compared to Hard Gold 200 – 250 Angstroms (1)2. 5 – 15 nanometer, compared to hard gold 20 – 25 nanometer (1)2. Palladium-cobalt has low porosity (ASTM B799) 0.2 porosity index compared to hard gold 3.7 porosity index (1)2. Palladium-cobalt coated surface has higher ductility (ASTM B489) 3-7 than that of hard gold 3,4).2TABLE 1 - Hardness of Noble Metals    
Approximate Hardness (HK25)  
Gold  
50–250  
Palladium  
75–600  
Platinum  
150–550  
Palladium-Nickel  
300–650  
Palladium-Cobalt  
500–650  
Rhodium  
750–1100  
Ruthenium  
600–1300
1.3 Units—The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Some specific hazards statements are given in Section 7 on Hazards.

ABSTRACT
This specification establishes the requirements for electrodeposited gold coatings for engineering applications, employed specifically for their corrosion and tarnish resistance (including resistance to fretting corrosion and catalytic polymerization), bondability, low and stable contact resistance, solderability, and infrared reflectivity. This specification does not cover gold coatings produced from autocatalytic, immersion, and vapor deposition. Coatings shall be classified into types, which characterize minimum purity, and codes, which designate Knoop hardness. Coatings shall be sampled, tested and conform to specified requirements as to purity, hardness, appearance, thickness, mass per unit area, ductility, adhesion (assessed by either bend, heat, or cutting test), and integrity (including gross defects, mechanical damage, and porosity).
SCOPE
1.1 This specification covers requirements for electrodeposited gold coatings that contain not less than 99.00 mass % gold and that are used for engineering applications.
1.2 Specifically excluded from this specification are autocatalytic, immersion, and vapor deposited gold coatings.
1.3 Gold coatings conforming to this specification are employed for their corrosion and tarnish resistance (including resistance to fretting corrosion and catalytic polymerization), bondability, low and stable contact resistance, solderability, and infrared reflectivity. Several types of coatings, differing in gold purity and hardness, are covered by this specification.
1.4 The values stated in SI units are to be regarded as the standard. Values provided in parentheses are for information only.
1.5 The following hazards caveat pertains only to the test methods section, Section 9, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ABSTRACT
This specification establishes the requirements for electrodeposited gold coatings for engineering applications, employed specifically for their corrosion and tarnish resistance (including resistance to fretting corrosion and catalytic polymerization), bondability, low and stable contact resistance, solderability, and infrared reflectivity. This specification does not cover gold coatings produced from autocatalytic, immersion, and vapor deposition. Coatings shall be classified into types, which characterize minimum purity, and codes, which designate Knoop hardness. Coatings shall be sampled, tested and conform to specified requirements as to purity, hardness, appearance, thickness, mass per unit area, ductility, adhesion (assessed by either bend, heat, or cutting test), and integrity (including gross defects, mechanical damage, and porosity).
SCOPE
1.1 This specification covers requirements for electrodeposited gold coatings that contain not less than 99.00 mass % gold and that are used for engineering applications.
1.2 Specifically excluded from this specification are autocatalytic, immersion, and vapor deposited gold coatings.
1.3 Gold coatings conforming to this specification are employed for their corrosion and tarnish resistance (including resistance to fretting corrosion and catalytic polymerization), bondability, low and stable contact resistance, solderability, and infrared reflectivity. Several types of coatings, differing in gold purity and hardness, are covered by this specification.
1.4 The values stated in SI units are to be regarded as the standard. Values provided in parentheses are for information only.
1.5 The following hazards caveat pertains only to the test methods section, Section 9, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ABSTRACT
This specification establishes the requirements for electrodeposited gold coatings for engineering applications, employed specifically for their corrosion and tarnish resistance (including resistance to fretting corrosion and catalytic polymerization), bondability, low and stable contact resistance, solderability, and infrared reflectivity. This specification does not cover gold coatings produced from autocatalytic, immersion, and vapor deposition. Coatings shall be classified into types, which characterize minimum purity, and codes, which designate Knoop hardness. Coatings shall be sampled, tested and conform to specified requirements as to purity, hardness, appearance, thickness, mass per unit area, ductility, adhesion (assessed by either bend, heat, or cutting test), and integrity (including gross defects, mechanical damage, and porosity).
SCOPE
1.1 This specification covers requirements for electrodeposited gold coatings that contain not less than 99.00 mass % gold and that are used for engineering applications.
1.2 Specifically excluded from this specification are autocatalytic, immersion, and vapor deposited gold coatings.
1.3 Gold coatings conforming to this specification are employed for their corrosion and tarnish resistance (including resistance to fretting corrosion and catalytic polymerization), bondability, low and stable contact resistance, solderability, and infrared reflectivity. Several types of coatings, differing in gold purity and hardness, are covered by this specification.
1.4 The values stated in SI units are to be regarded as the standard. Values provided in parentheses are for information only.
1.5 The following hazards caveat pertains only to the test methods section, Section 9, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ABSTRACT
This specification establishes the requirements for electrodeposited palladium coatings for use in engineering applications. This specification also covers composite coatings of palladium with a thin gold overplate for applications involving electrical contacts. The plating system shall indicate the basis metal involved, thickness of the underplates, thickness of the palladium coating, and grade of the gold overplate. Coatings shall be sampled, tested, and conform accordingly to specified requirements as to purity, appearance, thickness, dutility, adhesion (to be examined either by bend, heat, or cutting test), and integrity (gross defects, mechanical damage, and porosity).
SCOPE
1.1 This specification covers requirements for electrodeposited palladium coatings containing at least 99.7 mass % of palladium metal. Composite coatings consisting of palladium with a thin gold overplate for applications involving electrical contacts are also covered.
1.2 Properties—Palladium is the lightest and least noble of the platinum group metals. It has a specific gravity of 12.0, which is substantially less than gold (19.3) and platinum (21.5). This yields a greater volume or thickness of coating and, consequently, some saving of metal weight accompanied by a small sacrifice in corrosion resistance and reflectivity. The following table compares the hardness range of electrodeposited palladium with other electrodeposited noble metals and alloys (1,2).
  Approximate Hardness (HK25) Gold50–250 Palladium75–600 Platinum150–550 Palladium-Nickel300–650 Rhodium750–1100 Ruthenium600–1300
1.3 The values stated in SI units are the preferred values. Values provided in parentheses are for information only.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ABSTRACT
This specification covers the requirements for electrodeposited rhodium coatings for engineering applications, usually employed for their corrosion resistance, stable electrical contact resistance, wear resistance, reflectivity, and heat resistance. Coating shall be classified based on their thickness. Specimens shall undergo preparatory preplating procedures such as surface cleaning and stress relief treatment, as well as post-plating embrittlement relief process. Coatings shall be sampled, tested, and conform accordingly to specified requirements as to purity, appearance, adhesion, hydrogen embrittlement, reflectivity, and thickness (to be measured either nondestructively by beta backscatter method or X-ray fluorescence, or destructively by microscopical cross sectioning method).
SCOPE
1.1 This specification covers requirements for electrodeposited coatings of rhodium used for engineering purposes.
1.2 Coatings of rhodium covered by this specification are usually employed for their corrosion resistance, stable electrical contact resistance, wear resistance, reflectivity, and heat resistance.
1.3 Appendix X1 covers some typical applications for electrodeposited rhodium.
1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ABSTRACT
This specification establishes the requirements for electrodeposited silver coatings that may be mat, bright, or semibright, and are usually employed as solderable surfaces and for their electrical contact characteristics, high electrical and thermal conductivity, thermocompression bonding, wear resistance on load-bearing surfaces, and spectral reflectivity. Coatings shall be classified into types according to minimum purity, grade according to surface appearance (bright, semibright, or mat), and class according to whether any surface treatment has been applied. Coatings shall undergo preplating operations such as stress relief treatment, strike, and underplating, as well as post-plating embrittlement relief. Coatings shall be sampled, tested, and conform accordingly to specified requirements as to nature, purity, appearance, defects, adhesion, solderability, hardness, spectral reflectance, electrical conductivity, hydrogen embrittlement relief, and thickness (measured either nondestructively by beta backscatter, X-ray spectrometry, or magnetic method, or destructively by coulometric technique or microscopical cross-sectioning procedure).
SCOPE
1.1 This specification covers requirements for electrodeposited coatings of silver used for engineering purposes that may be mat, bright, or semibright and are not less than 98 % silver purity.
1.2 Coatings of silver covered by this specification are usually employed for solderable surfaces, electrical contact characteristics, high electrical and thermal conductivity, thermocompression bonding, wear resistance of load-bearing surfaces, and spectral reflectivity.
1.3 In the Appendixes important characteristics of electrodeposited silver coatings are briefly described which must be considered when used in engineering applications, namely electrical conductivity (see Appendix X1), silver migration (see Appendix X2), thickness (see Appendix X3), hardness (see Appendix X4), and atmospheric tarnish (see Appendix X5).
1.4 The following hazards caveat pertains only to the test methods section of this specification:  This standard does not purport to address the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ABSTRACT
This specification establishes the requirements for electrodeposited gold coatings for engineering applications, employed specifically for their corrosion and tarnish resistance (including resistance to fretting corrosion and catalytic polymerization), bondability, low and stable contact resistance, solderability, and infrared reflectivity. This specification does not cover gold coatings produced from autocatalytic, immersion, and vapor deposition. Coatings shall be classified into types, which characterize minimum purity, and codes, which designate Knoop hardness. Coatings shall be sampled, tested and conform to specified requirements as to purity, hardness, appearance, thickness, mass per unit area, ductility, adhesion (assessed by either bend, heat, or cutting test), and integrity (including gross defects, mechanical damage, and porosity).
SCOPE
1.1 This specification covers requirements for electrodeposited gold coatings that contain not less than 99.00 mass % gold and that are used for engineering applications.
1.2 Specifically excluded from this specification are autocatalytic, immersion, and vapor deposited gold coatings.
1.3 Gold coatings conforming to this specification are employed for their corrosion and tarnish resistance (including resistance to fretting corrosion and catalytic polymerization), bondability, low and stable contact resistance, solderability, and infrared reflectivity. Several types of coatings, differing in gold purity and hardness, are covered by this specification.
1.4 The values stated in SI units are to be regarded as the standard. Values provided in parentheses are for information only.
The following hazards caveat pertains only to the test methods section, Section , of this specification:This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ABSTRACT
This specification covers the requirements for electrodeposited rhodium coatings for engineering applications, usually employed for their corrosion resistance, stable electrical contact resistance, wear resistance, reflectivity, and heat resistance. Coating shall be classified based on their thickness. Specimens shall undergo preparatory preplating procedures such as surface cleaning and stress relief treatment, as well as post-plating embrittlement relief process. Coatings shall be sampled, tested, and conform accordingly to specified requirements as to purity, appearance, adhesion, hydrogen embrittlement, reflectivity, and thickness (to be measured either nondestructively by beta backscatter method or X-ray fluorescence, or destructively by microscopical cross sectioning method).
SCOPE
1.1 This specification covers requirements for electrodeposited coatings of rhodium used for engineering purposes.
1.2 Coatings of rhodium covered by this specification are usually employed for their corrosion resistance, stable electrical contact resistance, wear resistance, reflectivity, and heat resistance.
1.3 Appendix XI covers some typical applications for electrodeposited rhodium.
1.4 This standard does not purport to address all of the safety problems associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ABSTRACT
This specification establishes the requirements for electrodeposited palladium coatings for use in engineering applications. This specification also covers composite coatings of palladium with a thin gold overplate for applications involving electrical contacts. The plating system shall indicate the basis metal involved, thickness of the underplates, thickness of the palladium coating, and grade of the gold overplate. Coatings shall be sampled, tested, and conform accordingly to specified requirements as to purity, appearance, thickness, dutility, adhesion (to be examined either by bend, heat, or cutting test), and integrity (gross defects, mechanical damage, and porosity).
SCOPE
1.1 Purity -This specification covers requirements for electrodeposited palladium coatings containing at least 99.7 mass % of palladium metal.
1.2 Properties -Palladium is the lightest and least noble of the platinum group metals. It has a specific gravity of 12.0, which is substantially less than gold (19.3) and platinum (21.5). This yields a greater volume or thickness of coating and, consequently, some saving of metal weight accompanied by a small sacrifice in corrosion resistance and reflectivity. The hardness range of electrodeposited palladium compares favorably with the other electroplated noble metals and their alloys.  
1.3 The values stated in SI units are the preferred values. Values provided in parentheses are for information only.
1.4 The following hazards caveat pertains only to the test methods section of this specification: This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

SCOPE
1.1 This specification covers requirements for electrodeposited gold coatings that contain not less than 99.00 mass % gold and that are used for engineering applications.
1.2 Specifically excluded from this specification are autocatalytic, immersion, and vapor deposited gold coatings.
1.3 Gold coatings conforming to this specification are employed for their corrosion and tarnish resistance (including resistance to fretting corrosion and catalytic polymerization), bondability, low and stable contact resistance, solderability, and infrared reflectivity. Several types of coatings, differing in gold purity and hardness, are covered by this specification.
1.4 The values stated in SI units are to be regarded as the standard. Values provided in parentheses are for information only.
1.5 The following hazards caveat pertains only to the test methods section, Section 9, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

SCOPE
1.1 This specification covers requirements for electrodeposited gold coatings that contain not less than 99.00 mass % gold and that are used for engineering applications.
1.2 Specifically excluded from this specification are autocatalytic, immersion, and vapor deposited gold coatings.
1.3 Gold coatings conforming to this specification are employed for their corrosion and tarnish resistance (including resistance to fretting corrosion and catalytic polymerization), bondability, low and stable contact resistance, solderability, and infrared reflectivity. Several types of coatings, differing in gold purity and hardness, are covered by this specification.
1.4 The values stated in SI units are to be regarded as the standard. Values provided in parentheses are for information only.
1.5 The following hazards caveat pertains only to the test methods section, Section 9, of this specification:This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

SCOPE
1.1 This specification covers requirements for electrodeposited gold coatings that contain not less than 99.00 mass % gold and that are used for engineering applications.
1.2 Specifically excluded from this specification are autocatalytic, immersion, and vapor deposited gold coatings.
1.3 Gold coatings conforming to this specification are employed for their corrosion and tarnish resistance (including resistance to fretting corrosion and catalytic polymerization), bondability, low and stable contact resistance, solderability, and infrared reflectivity. Several types of coatings, differing in gold purity and hardness, are covered by this specification.
1.4 The values stated in SI units are to be regarded as the standard. Values provided in parentheses are for information only.
1.5 The following hazards caveat pertains only to the test methods section, Section 9, of this specification:This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

SCOPE
1.1 This specification covers requirements for electrodeposited coatings of rhodium used for engineering purposes.
1.2 Coatings of rhodium covered by this specification are usually employed for their corrosion resistance, stable electrical contact resistance, wear resistance, reflectivity, and heat resistance.
1.3 Appendix XI covers some typical applications for electrodeposited rhodium.
1.4 This standard does not purport to address all of the safety problems associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

SCOPE
1.1 Purity -This specification covers requirements for electrodeposited palladium coatings containing at least 99.7 mass % of palladium metal.
1.2 Properties -Palladium is the lightest and least noble of the platinum group metals. It has a specific gravity of 12.0, which is substantially less than gold (19.3) and platinum (21.5). This yields a greater volume or thickness of coating and, consequently, some saving of metal weight accompanied by a small sacrifice in corrosion resistance and reflectivity. The hardness range of electrodeposited palladium compares favorably with the other electroplated noble metals and their alloys.  
1.3 The values stated in SI units are the preferred values. Values provided in parentheses are for information only.
1.4 The following hazards caveat pertains only to the test methods section of this specification: This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

SCOPE
1.1 This specification covers requirements for electrodeposited coatings of silver used for engineering purposes that may be mat, bright, or semibright and are not less than 98% silver purity.  
1.2 Coatings of silver covered by this specification are usually employed for solderable surfaces, electrical contact characteristics, high electrical and thermal conductivity, thermocompression bonding, wear resistance of load-bearing surfaces, and special reflectivity.  
1.3 In the Appendixes important characteristics of electrodeposited silver coatings are briefly described which must be considered when used in engineering applications, namely electrical conductivity (see Appendix X1), silver migration (see Appendix X2), thickness (see Appendix X3), hardness (see Appendix X4), and atmospheric tarnish (see Appendix X5).  
1.4 The following hazards caveat pertains only to the test methods section of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

SCOPE
1.1 This specification covers requirements for electrodeposited coatings of silver used for engineering purposes that may be mat, bright, or semibright and are not less than 98% silver purity.  
1.2 Coatings of silver covered by this specification are usually employed for solderable surfaces, electrical contact characteristics, high electrical and thermal conductivity, thermocompression bonding, wear resistance of load-bearing surfaces, and special reflectivity.  
1.3 In the Appendixes important characteristics of electrodeposited silver coatings are briefly described which must be considered when used in engineering applications, namely electrical conductivity (see Appendix X1), silver migration (see Appendix X2), thickness (see Appendix X3), hardness (see Appendix X4), and atmospheric tarnish (see Appendix X5).  
1.4 The following hazards caveat pertains only to the test methods section of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.