F26.04 - Mechanical Preparation Equipment

ABSTRACT
This specification covers batch-type electric vegetable peeling machines of the following style: Style 1, Size A, and Style 2, Size A, Size B, and Size C. The cylinder or hopper shall be sheet aluminum or stainless steel, or cast iron. Machines intended for marine applications shall be furnished with a stainless steel cylinder. The inside surface of all cylinders shall be covered by silicon carbide or aluminum oxide. The disk shall be cast aluminum, formed stainless steel, or reinforced plastic. The cylinder covering ring shall be cast aluminum, spun sheet aluminum, or fiberglass-reinforced plastic. The supporting base of the flour mounted Style 2 machine shall be steel, aluminum, or stainless steel. The vegetable peeler shall comply to the specified physical requirements specified for the following: (1) cylinder or hopper, (2) disk, (3) vegetable outlet, (4) peel trap, (5) waste outlet, (6) water inlet and sprayer, (7) cylinder covering ring, (8) Style 1, counter mounted, (9) Style 2, floor mounted, (10) waste disposer, (11) electrical devices such as motors, wiring, timer, and switch, and (12) piping, tubing, fittings, and valves. The peeler shall meet the hazard protection requirements including switch guard and shall conform to the performance requirements which shall be tested by operational test.
SCOPE
1.1 This specification covers batch-type vegetable peeling machines.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 The following safety hazards caveat pertains only to the test methods portion, Section 9, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification covers vertical electric food mixing machines in a certain size range (as expressed by bowl capacity). These machines shall be adaptable for mixing, whipping, and beating food products. Optional construction features and attachments that enhance the mixing, beating, or whipping capabilities of the machine are also discussed. These machines shall consists of the following parts, equipment, and accessories: electric drive motor, speed selector, beater shaft, power supply, mixing bowls, agitators, bowl lift, bowl support, base, timer, attachment hub, and bowl truck. Optional equipments for these machines may include mixing bowl extension, bowl adapters, splash covers, and table. In order to determine the mixing machines' overall performance, the following tests shall be done: operational test, speed test, power bowl lift test and run-in test.
SCOPE
1.1 This specification covers vertical electric food mixing machines in the size range (as expressed by bowl capacity) from 5 to 140 qt. These machines shall be adaptable for mixing, whipping, and beating food products. This specification does not include special purpose machines that are intended solely for mixing dough.  
1.2 This specification also covers optional construction features and attachments that enhance the mixing, beating, or whipping capabilities of the machine. This specification does not cover ancillary equipment that can be driven by the attachment hub.  
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.4 The following precautionary caveat pertains only to the test methods portion, Section 9, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification covers commercial electric food cutters with a rotating shallow bowl to carry food products through a set of rotating vertical knives that are on an axis perpendicular to the radii of the bowl. The food cutter can be for counter or table mounting, furnished with or without a table. Food cutters shall be of the following types, sizes, and classes: Types I and II; Sizes 1 and 2; and Classes A and B. Test methods shall be performed to conform with the specified requirements.
SCOPE
1.1 This specification covers commercial electric food cutters with a rotating shallow bowl to carry food products through a set of rotating vertical knives that are on an axis perpendicular to the radii of the bowl. The food cutter can be for counter or table mounting, furnished with or without a table.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 The following precautionary caveat pertains only to the test method portion, Section 10, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification covers commercial food processors intended for bench, table, or floor mounting. Types: type I - this machine shall have a hopper of the continuous, manual-feed type, and type II - this machine shall have a closed-bowl type of hopper. Classes: class 1 - table- or bench-mounted food processor, and class 2 - floor-mounted food processor. Interlock integrity test, plate stopping time test, type I food processor operation tests, type II food processor operation test, motor performance test, power transmission test, and sound level test shall be performed to meet the requirements prescribed.
SCOPE
1.1 This specification covers commercial food processors intended for bench, table, or floor mounting.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 The following safety hazards caveat pertains only to the test methods portion, Section 9, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification covers commercial hand operated dough divider machines and semiautomatic and automatic, electrically operated, dough divider and rounding machines with or without interchangeable heads. Dough dividers and dough divider/rounding machines are classified by type, class, size, and styles: Types I, II, III, and IV; Classes I, II, and III; Sizes 1, 2, and 3; and Styles 1, 2, and 3. Operational test and performance test shall be performed to conform with the specified requirements.
SCOPE
1.1 This specification covers commercial hand operated dough divider machines and semiautomatic and automatic, electrically operated, dough divider and rounding machines with or without interchangeable heads.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification covers commercial, electrically operated, bun slicing machines. These slicing machines are classified by type, class, size and style. These machines have three types: Type I is electrically operated with single knife, Type II is electrically operated with dual knife, and Type III is a cluster-bun slicing machine, electrically operated with dual knife. They are also designated into three classes: Class I with a fixed chute, Class II with a adjustable chute, and Class III with automatic/conveyor feed. In terms of size, they come in three kinds: Size I (small), Size II (medium), and Size III(large). In terms of style, they can be classified into three kinds: Style I which is counter top or bench-mounted, Style II which is floor-mounted, and Style III which is portable. Bun slicing machines shall be delivered assembled, ready for mounting, connection to electricity, and use as applicable. The bun slicing machine shall be simple to disassemble and reassemble without special tools or equipment. Requirements for power supply, motor, motor controller, and cutting knife shall be discussed. All components and assemblies of the dough divider and rounder shall be free from dirt and other extraneous materials, burrs, slivers, tool and grind marks, dents, and cracks. Castings, molded parts and stampings shall be free of voids, sand pits, blow holes, and sprues. External surfaces shall be free from kinks, dents, and other deformities. Forming and welding shall not cause damage to the metal and shall be done neatly and accurately.
SCOPE
1.1 This specification covers commercial, electrically operated, bun slicing machines.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification covers the design and performance requirements pertinent to the construction of electrically operated commercial bread slicing machines. Bread slicing machines are classified into types according to feed mechanism, classes according to knife type, and styles into mountability, as follows: Type I—gravity feed; Type II—mechanical single-loaf feed; and Type III—mechanical multiple-loaf feed; Class I—reciprocating knife; Class II—circular knife; Class III—sickle knife; and Class IV—continuous (band) knife; Style I—countertop or stand mounted; Style 2—floor mounted; and Style 3—portable. Representative production models of the bread slicing machines shall pass operational and performance tests, and should function satisfactorily as specified.
SCOPE
1.1 This specification covers commercial, electrically operated, bread slicing machines.  
1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification covers commercial food slicers having electrically driven rotating slicing blades. Food slicers covered in this specification are classified into types and classes. Types: type I - fully automatic (powered carriage); and type II - semiautomatic (manually operated carriage). Classes: class A - bench mounted; class B - pedestal mounted; and class C - stand mounted with casters. Gage plate operation test, slicing rate test, uniformity test, slicer knife test, sharpener test, carriage operation test, power transmission test, switch test, and slicer stand loading test shall be performed to meet the requirements prescribed.
SCOPE
1.1 This specification covers commercial food slicers having electrically driven rotating slicing blades.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 The following precautionary caveat pertains only to the test method portion, Section 9, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification covers batch-type electric vegetable peeling machines of the following style: Style 1, Size A, and Style 2, Size A, Size B, and Size C. The cylinder or hopper shall be sheet aluminum or stainless steel, or cast iron. Machines intended for marine applications shall be furnished with a stainless steel cylinder. The inside surface of all cylinders shall be covered by silicon carbide or aluminum oxide. The disk shall be cast aluminum, formed stainless steel, or reinforced plastic. The cylinder covering ring shall be cast aluminum, spun sheet aluminum, or fiberglass-reinforced plastic. The supporting base of the flour mounted Style 2 machine shall be steel, aluminum, or stainless steel. The vegetable peeler shall comply to the specified physical requirements specified for the following: (1) cylinder or hopper, (2) disk, (3) vegetable outlet, (4) peel trap, (5) waste outlet, (6) water inlet and sprayer, (7) cylinder covering ring, (8) Style 1, counter mounted, (9) Style 2, floor mounted, (10) waste disposer, (11) electrical devices such as motors, wiring, timer, and switch, and (12) piping, tubing, fittings, and valves. The peeler shall meet the hazard protection requirements including switch guard and shall conform to the performance requirements which shall be tested by operational test.
SCOPE
1.1 This specification covers batch-type vegetable peeling machines.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 The following safety hazards caveat pertains only to the test methods portion, Section 9, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification covers commercial food processors intended for bench, table, or floor mounting. Types: type I - this machine shall have a hopper of the continuous, manual-feed type, and type II - this machine shall have a closed-bowl type of hopper. Classes: class 1 - table- or bench-mounted food processor, and class 2 - floor-mounted food processor. Interlock integrity test, plate stopping time test, type I food processor operation tests, type II food processor operation test, motor performance test, power transmission test, and sound level test shall be performed to meet the requirements prescribed.
SCOPE
1.1 This specification covers commercial food processors intended for bench, table, or floor mounting.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 The following safety hazards caveat pertains only to the test methods portion, Section 9, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification covers commercial hand operated dough divider machines and semiautomatic and automatic, electrically operated, dough divider and rounding machines with or without interchangeable heads. Dough dividers and dough divider/rounding machines are classified by type, class, size, and styles: Types I, II, III, and IV; Classes I, II, and III; Sizes 1, 2, and 3; and Styles 1, 2, and 3. Operational test and performance test shall be performed to conform with the specified requirements.
SCOPE
1.1 This specification covers commercial hand operated dough divider machines and semiautomatic and automatic, electrically operated, dough divider and rounding machines with or without interchangeable heads.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification covers vertical electric food mixing machines in a certain size range (as expressed by bowl capacity). These machines shall be adaptable for mixing, whipping, and beating food products. Optional construction features and attachments that enhance the mixing, beating, or whipping capabilities of the machine are also discussed. These machines shall consists of the following parts, equipment, and accessories: electric drive motor, speed selector, beater shaft, power supply, mixing bowls, agitators, bowl lift, bowl support, base, timer, attachment hub, and bowl truck. Optional equipments for these machines may include mixing bowl extension, bowl adapters, splash covers, and table. In order to determine the mixing machines' overall performance, the following tests shall be done: operational test, speed test, power bowl lift test and run-in test.
SCOPE
1.1 This specification covers vertical electric food mixing machines in the size range (as expressed by bowl capacity) from 5 to 140 qt. These machines shall be adaptable for mixing, whipping, and beating food products. This specification does not include special purpose machines that are intended solely for mixing dough.  
1.2 This specification also covers optional construction features and attachments that enhance the mixing, beating, or whipping capabilities of the machine. This specification does not cover ancillary equipment that can be driven by the attachment hub.  
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.4 The following precautionary caveat pertains only to the test methods portion, Section 9, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification covers commercial electric food cutters with a rotating shallow bowl to carry food products through a set of rotating vertical knives that are on an axis perpendicular to the radii of the bowl. The food cutter can be for counter or table mounting, furnished with or without a table. Food cutters shall be of the following types, sizes, and classes: Types I and II; Sizes 1 and 2; and Classes A and B. Test methods shall be performed to conform with the specified requirements.
SCOPE
1.1 This specification covers commercial electric food cutters with a rotating shallow bowl to carry food products through a set of rotating vertical knives that are on an axis perpendicular to the radii of the bowl. The food cutter can be for counter or table mounting, furnished with or without a table.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 The following precautionary caveat pertains only to the test method portion, Section 10, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification covers the design and performance requirements pertinent to the construction of electrically operated commercial bread slicing machines. Bread slicing machines are classified into types according to feed mechanism, classes according to knife type, and styles into mountability, as follows: Type I—gravity feed; Type II—mechanical single-loaf feed; and Type III—mechanical multiple-loaf feed; Class I—reciprocating knife; Class II—circular knife; Class III—sickle knife; and Class IV—continuous (band) knife; Style I—countertop or stand mounted; Style 2—floor mounted; and Style 3—portable. Representative production models of the bread slicing machines shall pass operational and performance tests, and should function satisfactorily as specified.
SCOPE
1.1 This specification covers commercial, electrically operated, bread slicing machines.  
1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ABSTRACT
This specification covers commercial, electrically operated, bun slicing machines. These slicing machines are classified by type, class, size and style. These machines have three types: Type I is electrically operated with single knife, Type II is electrically operated with dual knife, and Type III is a cluster-bun slicing machine, electrically operated with dual knife. They are also designated into three classes: Class I with a fixed chute, Class II with a adjustable chute, and Class III with automatic/conveyor feed. In terms of size, they come in three kinds: Size I (small), Size II (medium), and Size III(large). In terms of style, they can be classified into three kinds: Style I which is counter top or bench-mounted, Style II which is floor-mounted, and Style III which is portable. Bun slicing machines shall be delivered assembled, ready for mounting, connection to electricity, and use as applicable. The bun slicing machine shall be simple to disassemble and reassemble without special tools or equipment. Requirements for power supply, motor, motor controller, and cutting knife shall be discussed. All components and assemblies of the dough divider and rounder shall be free from dirt and other extraneous materials, burrs, slivers, tool and grind marks, dents, and cracks. Castings, molded parts and stampings shall be free of voids, sand pits, blow holes, and sprues. External surfaces shall be free from kinks, dents, and other deformities. Forming and welding shall not cause damage to the metal and shall be done neatly and accurately.
SCOPE
1.1 This specification covers commercial, electrically operated, bun slicing machines.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ABSTRACT
This specification covers commercial food slicers having electrically driven rotating slicing blades. Food slicers covered in this specification are classified into types and classes. Types: type I - fully automatic (powered carriage); and type II - semiautomatic (manually operated carriage). Classes: class A - bench mounted; class B - pedestal mounted; and class C - stand mounted with casters. Gage plate operation test, slicing rate test, uniformity test, slicer knife test, sharpener test, carriage operation test, power transmission test, switch test, and slicer stand loading test shall be performed to meet the requirements prescribed.
SCOPE
1.1 This specification covers commercial food slicers having electrically driven rotating slicing blades.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 The following precautionary caveat pertains only to the test method portion, Section 9, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ABSTRACT
This specification covers batch-type electric vegetable peeling machines of the following style: Style 1, Size A, and Style 2, Size A, Size B, and Size C. The cylinder or hopper shall be sheet aluminum or stainless steel, or cast iron. Machines intended for marine applications shall be furnished with a stainless steel cylinder. The inside surface of all cylinders shall be covered by silicon carbide or aluminum oxide. The disk shall be cast aluminum, formed stainless steel, or reinforced plastic. The cylinder covering ring shall be cast aluminum, spun sheet aluminum, or fiberglass-reinforced plastic. The supporting base of the flour mounted Style 2 machine shall be steel, aluminum, or stainless steel. The vegetable peeler shall comply to the specified physical requirements specified for the following: (1) cylinder or hopper, (2) disk, (3) vegetable outlet, (4) peel trap, (5) waste outlet, (6) water inlet and sprayer, (7) cylinder covering ring, (8) Style 1, counter mounted, (9) Style 2, floor mounted, (10) waste disposer, (11) electrical devices such as motors, wiring, timer, and switch, and (12) piping, tubing, fittings, and valves. The peeler shall meet the hazard protection requirements including switch guard and shall conform to the performance requirements which shall be tested by operational test.
SCOPE
1.1 This specification covers batch-type vegetable peeling machines.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 The following safety hazards caveat pertains only to the test methods portion, Section 9, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ABSTRACT
This specification covers commercial hand operated dough divider machines and semiautomatic and automatic, electrically operated, dough divider and rounding machines with or without interchangeable heads. Dough dividers and dough divider/rounding machines are classified by type, class, size, and styles: Types I, II, III, and IV; Classes I, II, and III; Sizes 1, 2, and 3; and Styles 1, 2, and 3. Operational test and performance test shall be performed to conform with the specified requirements.
SCOPE
1.1 This specification covers commercial hand operated dough divider machines and semiautomatic and automatic, electrically operated, dough divider and rounding machines with or without interchangeable heads.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ABSTRACT
This specification covers commercial food processors intended for bench, table, or floor mounting. Types: type I - this machine shall have a hopper of the continuous, manual-feed type, and type II - this machine shall have a closed-bowl type of hopper. Classes: class 1 - table- or bench-mounted food processor, and class 2 - floor-mounted food processor. Interlock integrity test, plate stopping time test, type I food processor operation tests, type II food processor operation test, motor performance test, power transmission test, and sound level test shall be performed to meet the requirements prescribed.
SCOPE
1.1 This specification covers commercial food processors intended for bench, table, or floor mounting.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 The following safety hazards caveat pertains only to the test methods portion, Section 9, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ABSTRACT
This specification covers vertical electric food mixing machines in a certain size range (as expressed by bowl capacity). These machines shall be adaptable for mixing, whipping, and beating food products. Optional construction features and attachments that enhance the mixing, beating, or whipping capabilities of the machine are also discussed. These machines shall consists of the following parts, equipment, and accessories: electric drive motor, speed selector, beater shaft, power supply, mixing bowls, agitators, bowl lift, bowl support, base, timer, attachment hub, and bowl truck. Optional equipments for these machines may include mixing bowl extension, bowl adapters, splash covers, and table. In order to determine the mixing machines' overall performance, the following tests shall be done: operational test, speed test, power bowl lift test and run-in test.
SCOPE
1.1 This specification covers vertical electric food mixing machines in the size range (as expressed by bowl capacity) from 5 to 140 qt. These machines shall be adaptable for mixing, whipping, and beating food products. This specification does not include special purpose machines that are intended solely for mixing dough.  
1.2 This specification also covers optional construction features and attachments that enhance the mixing, beating, or whipping capabilities of the machine. This specification does not cover ancillary equipment that can be driven by the attachment hub.  
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.4 The following precautionary caveat pertains only to the test methods portion, Section 9, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ABSTRACT
This specification covers commercial electric food cutters with a rotating shallow bowl to carry food products through a set of rotating vertical knives that are on an axis perpendicular to the radii of the bowl. The food cutter can be for counter or table mounting, furnished with or without a table. Food cutters shall be of the following types, sizes, and classes: Types I and II; Sizes 1 and 2; and Classes A and B. Test methods shall be performed to conform with the specified requirements.
SCOPE
1.1 This specification covers commercial electric food cutters with a rotating shallow bowl to carry food products through a set of rotating vertical knives that are on an axis perpendicular to the radii of the bowl. The food cutter can be for counter or table mounting, furnished with or without a table.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 The following precautionary caveat pertains only to the test method portion, Section 10, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ABSTRACT
This specification covers the design and performance requirements pertinent to the construction of electrically operated commercial bread slicing machines. Bread slicing machines are classified into types according to feed mechanism, classes according to knife type, and styles into mountability, as follows: Type I—gravity feed; Type II—mechanical single-loaf feed; and Type III—mechanical multiple-loaf feed; Class I—reciprocating knife; Class II—circular knife; Class III—sickle knife; and Class IV—continuous (band) knife; Style I—countertop or stand mounted; Style 2—floor mounted; and Style 3—portable. Representative production models of the bread slicing machines shall pass operational and performance tests, and should function satisfactorily as specified.
SCOPE
1.1 This specification covers commercial, electrically operated, bread slicing machines.
1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ABSTRACT
This specification covers commercial, electrically operated, bun slicing machines. These slicing machines are classified by type, class, size and style. These machines have three types: Type I is electrically operated with single knife, Type II is electrically operated with dual knife, and Type III is a cluster-bun slicing machine, electrically operated with dual knife. They are also designated into three classes: Class I with a fixed chute, Class II with a adjustable chute, and Class III with automatic/conveyor feed. In terms of size, they come in three kinds: Size I (small), Size II (medium), and Size III(large). In terms of style, they can be classified into three kinds: Style I which is counter top or bench-mounted, Style II which is floor-mounted, and Style III which is portable. Bun slicing machines shall be delivered assembled, ready for mounting, connection to electricity, and use as applicable. The bun slicing machine shall be simple to disassemble and reassemble without special tools or equipment. Requirements for power supply, motor, motor controller, and cutting knife shall be discussed. All components and assemblies of the dough divider and rounder shall be free from dirt and other extraneous materials, burrs, slivers, tool and grind marks, dents, and cracks. Castings, molded parts and stampings shall be free of voids, sand pits, blow holes, and sprues. External surfaces shall be free from kinks, dents, and other deformities. Forming and welding shall not cause damage to the metal and shall be done neatly and accurately.
SCOPE
1.1 This specification covers commercial, electrically operated, bun slicing machines.
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ABSTRACT
This specification covers commercial food slicers having electrically driven rotating slicing blades. Food slicers covered in this specification are classified into types and classes. Types: type I - fully automatic (powered carriage); and type II - semiautomatic (manually operated carriage). Classes: class A - bench mounted; class B - pedestal mounted; and class C - stand mounted with casters. Gage plate operation test, slicing rate test, uniformity test, slicer knife test, sharpener test, carriage operation test, power transmission test, switch test, and slicer stand loading test shall be performed to meet the requirements prescribed.
SCOPE
1.1 This specification covers commercial food slicers having electrically driven rotating slicing blades.
1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.
1.3 The following precautionary caveat pertains only to the test method portion, Section 9, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ABSTRACT
This specification covers batch-type electric vegetable peeling machines of the following style: Style 1, Size A, and Style 2, Size A, Size B, and Size C. The cylinder or hopper shall be sheet aluminum or stainless steel, or cast iron. Machines intended for marine applications shall be furnished with a stainless steel cylinder. The inside surface of all cylinders shall be covered by silicon carbide or aluminum oxide. The disk shall be cast aluminum, formed stainless steel, or reinforced plastic. The cylinder covering ring shall be cast aluminum, spun sheet aluminum, or fiberglass-reinforced plastic. The supporting base of the flour mounted Style 2 machine shall be steel, aluminum, or stainless steel. The vegetable peeler shall comply to the specified physical requirements specified for the following: (1) cylinder or hopper, (2) disk, (3) vegetable outlet, (4) peel trap, (5) waste outlet, (6) water inlet and sprayer, (7) cylinder covering ring, (8) Style 1, counter mounted, (9) Style 2, floor mounted, (10) waste disposer, (11) electrical devices such as motors, wiring, timer, and switch, and (12) piping, tubing, fittings, and valves. The peeler shall meet the hazard protection requirements including switch guard and shall conform to the performance requirements which shall be tested by operational test.
SCOPE
1.1 This specification covers batch-type vegetable peeling machines.
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.3 The following safety hazards caveat pertains only to the test methods portion, Section 9, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ABSTRACT
This specification covers commercial hand operated dough divider machines and semiautomatic and automatic, electrically operated, dough divider and rounding machines with or without interchangeable heads. Dough dividers and dough divider/rounding machines are classified by type, class, size, and styles: Types I, II, III, and IV; Classes I, II, and III; Sizes 1, 2, and 3; and Styles 1, 2, and 3. Operational test and performance test shall be performed to conform with the specified requirements.
SCOPE
1.1 This specification covers commercial hand operated dough divider machines and semiautomatic and automatic, electrically operated, dough divider and rounding machines with or without interchangeable heads.
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ABSTRACT
This specification covers commercial electric food cutters with a rotating shallow bowl to carry food products through a set of rotating vertical knives that are on an axis perpendicular to the radii of the bowl. The food cutter can be for counter or table mounting, furnished with or without a table. Food cutters shall be of the following types, sizes, and classes: Types I and II; Sizes 1 and 2; and Classes A and B. Test methods shall be performed to conform with the specified requirements.
SCOPE
1.1 This specification covers commercial electric food cutters with a rotating shallow bowl to carry food products through a set of rotating vertical knives that are on an axis perpendicular to the radii of the bowl. The food cutter can be for counter or table mounting, furnished with or without a table.
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.3 The following precautionary caveat pertains only to the test method portion, Section 10, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ABSTRACT
This specification covers vertical electric food mixing machines in a certain size range (as expressed by bowl capacity). These machines shall be adaptable for mixing, whipping, and beating food products. Optional construction features and attachments that enhance the mixing, beating, or whipping capabilities of the machine are also discussed. These machines shall consists of the following parts, equipment, and accessories: electric drive motor, speed selector, beater shaft, power supply, mixing bowls, agitators, bowl lift, bowl support, base, timer, attachment hub, and bowl truck. Optional equipments for these machines may include mixing bowl extension, bowl adapters, splash covers, and table. In order to determine the mixing machines' overall performance, the following tests shall be done: operational test, speed test, power bowl lift test and run-in test.
SCOPE
1.1 This specification covers vertical electric food mixing machines in the size range (as expressed by bowl capacity) from 5 to 140 qt. These machines shall be adaptable for mixing, whipping, and beating food products. This specification does not include special purpose machines that are intended solely for mixing dough.
1.2 This specification also covers optional construction features and attachments that enhance the mixing, beating, or whipping capabilities of the machine. This specification does not cover ancillary equipment that can be driven by the attachment hub.
1.3 The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard.
1.4 The following precautionary caveat pertains only to the test methods portion, Section 9, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ABSTRACT
This specification covers commercial food processors intended for bench, table, or floor mounting. Types: type I - this machine shall have a hopper of the continuous, manual-feed type, and type II - this machine shall have a closed-bowl type of hopper. Classes: class 1 - table- or bench-mounted food processor, and class 2 - floor-mounted food processor. Interlock integrity test, plate stopping time test, type I food processor operation tests, type II food processor operation test, motor performance test, power transmission test, and sound level test shall be performed to meet the requirements prescribed.
SCOPE
1.1 This specification covers commercial food processors intended for bench, table, or floor mounting.
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.3 The following safety hazards caveat pertains only to the test methods portion, Section 9, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ABSTRACT
This specification covers commercial food slicers having electrically driven rotating slicing blades. Food slicers covered in this specification are classified into types and classes. Types: type I - fully automatic (powered carriage); and type II - semiautomatic (manually operated carriage). Classes: class A - bench mounted; class B - pedestal mounted; and class C - stand mounted with casters. Gage plate operation test, slicing rate test, uniformity test, slicer knife test, sharpener test, carriage operation test, power transmission test, switch test, and slicer stand loading test shall be performed to meet the requirements prescribed.
SCOPE
1.1 This specification covers commercial food slicers having electrically-driven rotating slicing blades.  
1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.  
1.3 The following precautionary caveat pertains only to the test method portion, Section 9, of this specification:  This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ABSTRACT
This specification covers batch-type electric vegetable peeling machines of the following style: Style 1, Size A, and Style 2, Size A, Size B, and Size C. The cylinder or hopper shall be sheet aluminum or stainless steel, or cast iron. Machines intended for marine applications shall be furnished with a stainless steel cylinder. The inside surface of all cylinders shall be covered by silicon carbide or aluminum oxide. The disk shall be cast aluminum, formed stainless steel, or reinforced plastic. The cylinder covering ring shall be cast aluminum, spun sheet aluminum, or fiberglass-reinforced plastic. The supporting base of the flour mounted Style 2 machine shall be steel, aluminum, or stainless steel. The vegetable peeler shall comply to the specified physical requirements specified for the following: (1) cylinder or hopper, (2) disk, (3) vegetable outlet, (4) peel trap, (5) waste outlet, (6) water inlet and sprayer, (7) cylinder covering ring, (8) Style 1, counter mounted, (9) Style 2, floor mounted, (10) waste disposer, (11) electrical devices such as motors, wiring, timer, and switch, and (12) piping, tubing, fittings, and valves. The peeler shall meet the hazard protection requirements including switch guard and shall conform to the performance requirements which shall be tested by operational test.
SCOPE
1.1 This specification covers batch-type vegetable peeling machines.
1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.
1.3 The following safety hazards caveat pertains only to the test methods portion, Section 9, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

SCOPE
1.1 This specification covers vertical electric food mixing machines in the size range (as expressed by bowl capacity) from 5 to 140 qt. These machines shall be adaptable for mixing, whipping, and beating food products. This specification does not include special purpose machines that are intended solely for mixing dough.
1.2 This specification also covers optional construction features and attachments that enhance the mixing, beating, or whipping capabilities of the machine. This specification does not cover ancillary equipment that can be driven by the attachment hub.
1.3 The values stated in inch-pound units are to be regarded as the standard.
1.4 The following precautionary caveat pertains only to the test methods portion, Section , of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

SCOPE
1.1 This specification covers batch-type vegetable peeling machines.
1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.
1.3 The following safety hazards caveat pertains only to the test methods portion, Section , of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

SCOPE
1.1 This specification covers commercial hand operated dough divider machines and semi-automatic and automatic, electrically operated, dough divider and rounding machines with or without interchangeable heads.
1.2 The values stated in inch-pound units are to be regarded as the standard. The SI values given in parentheses are for information only.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

SCOPE
1.1 This specification covers commercial food processors intended for bench, table, or floor mounting.
1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.
1.3 The following safety hazards caveat pertains only to the test methods portion, Section , of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

SCOPE
1.1 This specification covers commercial electric food cutters with a rotating shallow bowl to carry food products through a set of rotating vertical knives that are on an axis perpendicular to the radii of the bowl. The food cutter can be for counter or table mounting, furnished with or without a table.
1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.  
1.3 The following precautionary caveat pertains only to the test method portion, Section 10, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

SCOPE
1.1 This specification covers commercial food slicers having electrically-driven rotating slicing blades.  
1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.  
1.3 The following precautionary caveat pertains only to the test method portion, Section 9, of this specification:  This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

SCOPE
1.1 This specification covers vertical electric food mixing machines in the size range (as expressed by bowl capacity) from 12 to 140 qt. These machines shall be adaptable for mixing, whipping, and beating food products. This specification does not include special purpose machines that are intended solely for mixing dough.  
1.2 This specification also covers optional construction features and attachments that enhance the mixing, beating, or whipping capabilities of the machine. This specification does not cover ancillary equipment that can be driven by the attachment hub.  
1.3 The values stated in inch-pound units are to be regarded as the standard.  
1.4 The following precautionary caveat pertains only to the test methods portion, Section 9, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

SCOPE
1.1 This specification covers batch-type vegetable peeling machines.
1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.
1.3 The following safety hazards caveat pertains only to the test methods portion, Section 12, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

SCOPE
1.1 This specification covers commercial food processors intended for bench or table mounting.
1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.
1.3 The following safety hazards caveat pertains only to the test methods portion, Section 10, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

SCOPE
1.1 This specification covers commercial hand operated dough divider machines and semi-automatic and automatic, electrically operated, dough divider and rounding machines with or without interchangeable heads.
1.2 The values stated in inch-pound units are to be regarded as the standard. The SI values given in parentheses are for information only.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

SCOPE
1.1 This specification covers commercial electric food cutters with a rotating shallow bowl to carry food products through a set of rotating vertical knives that are on an axis perpendicular to the radii of the bowl. The food cutter can be for counter or table mounting, furnished with or without a table.
1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.  
1.3 The following precautionary caveat pertains only to the test method portion, Section 10, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.