A01.94 - U.S. Government Requirements for Steel Mill and Foundry Products

ABSTRACT
These practices cover the packaging, marking, and loading of steel products for shipment, and are intended to deliver the products to their destination in good condition. It is also intended that these recommendations be used as guides for attaining uniformity, simplicity, adequacy, and economy in the shipment of steel products. These practices cover semi-finished steel products, bars, bar-size shapes and sheet pilings, rods, wire and wire products, tubular products, plates, sheets, and strips, tin mill products, and castings.
SCOPE
1.1 This guide covers the packaging, marking, and loading of steel products for shipment. Assuming proper handling in transit, this guide is intended to assist shippers in packaging and loading steel products to arrive at their destination safely and in good condition. It is also intended that this guide may be used for attaining uniformity, simplicity, sufficiency, and economy in the shipment of steel products.  
1.2 This guide applies to semi-finished steel products, bars, structural shapes and sheet piling, rods, wire and wire products, tubular products, plates, sheets, and strips, tin mill products, and castings.  
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
These practices cover the packaging, marking, and loading of steel products for shipment, and are intended to deliver the products to their destination in good condition. It is also intended that these recommendations be used as guides for attaining uniformity, simplicity, adequacy, and economy in the shipment of steel products. These practices cover semi-finished steel products, bars, bar-size shapes and sheet pilings, rods, wire and wire products, tubular products, plates, sheets, and strips, tin mill products, and castings.
SCOPE
1.1 This guide covers the packaging, marking, and loading of steel products for shipment. Assuming proper handling in transit, this guide is intended to assist shippers in packaging and loading steel products to arrive at their destination safely and in good condition. It is also intended that this guide may be used for attaining uniformity, simplicity, sufficiency, and economy in the shipment of steel products.  
1.2 This guide applies to semi-finished steel products, bars, structural shapes and sheet piling, rods, wire and wire products, tubular products, plates, sheets, and strips, tin mill products, and castings.  
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ABSTRACT
These practices cover the packaging, marking, and loading of steel products for shipment, and are intended to deliver the products to their destination in good condition. It is also intended that these recommendations be used as guides for attaining uniformity, simplicity, adequacy, and economy in the shipment of steel products. These practices cover semi-finished steel products, bars, bar-size shapes and sheet pilings, rods, wire and wire products, tubular products, plates, sheets, and strips, tin mill products, and castings.
SCOPE
1.1 These practices cover the packaging, marking, and loading of steel products for shipment. Assuming proper handling in transit, the practices are intended to deliver the products to their destination in good condition. It is also intended that these recommendations be used as guides for attaining uniformity, simplicity, adequacy, and economy in the shipment of steel products.
1.2 These practices cover semi-finished steel products, bars, bar-size shapes and sheet piling, rods, wire and wire products, tubular products, plates, sheets, and strips, tin mill products, and castings. A glossary of packaging, marking, and loading terms is also included.
1.3 The practices are presented in the following sequence:
1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.5This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
WITHDRAWN RATIONALE
These practices cover the packaging, marking, and loading of steel products for shipment. Assuming proper handling in transit, the practices are intended to deliver the products to their destination in good condition. It is also intended that these recommendations be used as guides for attaining uniformity, simplicity, adequacy, and economy in the shipment of steel products.
Formerly under the jurisdiction of Committee A01 on Steel, Stainless Steel and Related Alloys, this practice was withdrawn in January 2014 in accordance with section 10.6.3 of the Regulations Governing ASTM Technical Committees, which requires that standards shall be updated by the end of the eighth year since the last approval date.

SCOPE
1.1 These practices cover the packaging, marking, and loading of steel products for domestic shipment. Assuming proper handling in transit, the practices are intended to deliver the products to their destination in good condition. It is also intended that these recommendations be used as guides for attaining uniformity, simplicity, adequacy, and economy in the domestic shipment of steel products.
1.2 These practices cover semi-finished steel products, bars, bar-size shapes and sheet piling, rods, wire and wire products, tubular products, plates, sheets, and strips, tin mill products, and castings. A glossary of packaging, marking, and loading terms is also included.
1.3 The practices are presented in the following sequence: SectionGeneral Provisions 4General 4.1Railcar Loading4.2Truck Loading 4.3Barge Loading 4.4Air Shipment4.5Packaging Materials4.6Package Identification4.7Weight and Count 4.8Packaging Lists or Tally4.9Loss or Damage4.10Semifinished Steel Products 5Hot-Rolled Bars and Bar-Size Shapes6Cold-Finished Bars7Structural Shapes and Steel Sheet Piling8Rods, Wire, and Wire Products9Tubular Products10Plates11Sheets and Strip12Tin Mill Products13Castings14