D12 - Soaps and Other Detergents

ABSTRACT
This test method covers the determination of the efficiency of ordinary commercial wetting agents using the skein test. It is applicable under limited and controlled conditions, but does not necessarily yield information correlating with specific end uses. The apparatus is comprised of a hook of standard weight depending on the concentration of the wetting agents and an anchor which shall be a flat, cylindrical, lead slug of specific dimensions. The reagents shall consist of water, acid and base test solutions, and wetting agent. The average of at least four determinations of the sinking time for each concentration of wetting agent shall be obtained and presented in plots with logarithmic coordinates. Standard deviation based on six replicate determinations shall also be calculated for precision.
SCOPE
1.1 This test method2,3 covers the determination of the efficiency of ordinary commercial wetting agents as defined in Terminology D459. This test method is applicable under limited and controlled conditions, but does not necessarily yield information correlating with specific end uses.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This guide details the standard procedures for the preparation of aqueous solutions of soaps and detergents and the determination of their pH. The required reagent for this procedure is distilled water or its equivalent, and the recommended electrodes for the determination of pH are the Fischer Accuphast combination electrode or Orion Ross Sure Flow electrode or their equivalents.
SCOPE
1.1 This guide covers the preparation of aqueous solutions of soaps and detergents and the determination of their pH.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Material Safety Data Sheets are available for reagents and materials. Review them for hazards prior to usage.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

SIGNIFICANCE AND USE
4.1 The guide, as now constituted, is not suitable for ranking of detergent products since no basis is available at this time for correlation of the detergency performance of any particular soiled cloth or clothes with detergency of naturally soiled articles.  
4.2 A suggested procedure for comparing the performance of any two laundry detergents on naturally soiled family items in home laundry equipment under controlled conditions on a paired comparison basis is described in Method D2960.
SCOPE
1.1 This is a guide for measuring the ability of detergents to remove artificially applied soils from fabrics. It is intended as a laboratory screening test to aid in the formulation of detergent products, for quality control and as a basis between the purchaser and seller in standardizing specific products' performance.  
1.2 The relative ranking of detergent products will vary greatly depending on the type of soiled fabrics used in the test. Therefore, selection of the standard soiled fabric to be used in a test shall be made by agreement between the interested parties on the basis of experience.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

SIGNIFICANCE AND USE
5.1 The methods in this guide can be used for screening of fabric softener products or to evaluate their performance, through a single cycle or multiple accumulative cycles, relative to a designated reference product or a comparative product(s).  
5.2 A single assessment of each of the product characteristics tested by these methods will not predict overall performance of the softener product. A single test run under specified fixed conditions cannot be expected to reflect the comparative performance under many other possible conditions of use.
SCOPE
1.1 This guide evaluates the performance characteristics of fabric softener products. It provides guidance for evaluating the on fabric efficacy of treatment chemicals dosed into the wash, rinse, or dryer cycle in a home laundry washer or dryer. This guide can be used for screening of fabric softener products, or to evaluate the products through multiple accumulative cycles.  
1.2 The relative ranking of products assessed by these procedures may be affected by such factors as machine type and settings, fabric load composition, as well as by the washing and drying procedures used.  
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

SIGNIFICANCE AND USE
5.1 The guide can be used to compare anti-redeposition performance of products; however, there is no confirmed basis for correlation of this controlled laboratory technique with consumers’ ranking of anti-redeposition performance.
SCOPE
1.1 This guide provides direction for measuring the ability of detergents to prevent the deposition of soils from detergent solutions onto fabrics. It is intended as a laboratory screening test to aid in the formulation of detergent products, for quality control, and as a basis between the purchaser and seller in standardizing specific products' performance.  
1.2 The anti-soil deposition performance of detergent products will vary greatly depending on the type of soils and fabrics used in the test. Therefore, selection of the soils, fabrics, reference detergents, and test conditions shall be made by agreement between the interested parties on the basis of experience.  
1.3 There is no single or combination of oily soils or particulate soils, or both, that will precisely predict overall the performance of a product or treatment with respect to anti-redeposition as perceived by a consumer. This guide is intended to assess or compare detergent performance with respect to the anti-redeposition performance for the specific soil chosen.  
1.4 The values stated in either inch-pound or SI units are to be regarded separately as the standard. The values given in parentheses are for information only.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Material safety data sheets are available for reagents and materials. Review them for hazards prior to usage.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

SIGNIFICANCE AND USE
5.1 A critical step in preparing a medical device for safe use on the next patient is effective cleaning. Typically cleaning a medical device includes precleaning at the point-of-use, manual and automated methods for removing soil that accumulate during clinical use. The cleaning solution(s) used are almost always water for rinsing and water with a detergent during washing. AAMI TIR34 (also EN 285) provides guidance about the quality of water to be used during reprocessing. This guidance references various test methods to ensure that water meets the recommended quality.  
5.2 When it comes to detergents very little guidance can be found in AAMI, ISO, ASTM, and FDA documents. Further, there are very few consensus methods for evaluating the detergents intended to clean medical devices. The result is that very little detail about detergents, for comparison purposes, is known. As a result, device manufacturers, when authoring their instructions for use (IFU) describe in very generic terms the kind of detergent that can be used to clean their device. Similarly, regulators, also have very little to rely upon for clearing reprocessing instructions. Finally, the healthcare facility, that is ultimately responsible for getting the device clean, has very little detail to assure that one brand of detergent is roughly equivalent to the one used by the medical device manufacturer during validation testing.  
5.3 While consensus standard test methods do not exist for detergents intended to clean medical devices, there are dozens of such test methods when it comes to detergents intended to clean dishes, laundry, floors, countertops, and so forth. Many of these methods are under the domain of ASTM D12: Soaps and other Cleaning Agents Including Detergents. While differences certainly do exist, essentially the detergents used for the other purposes are roughly formulated in the same way. Using existing test methods can drive detergent formulation development or determine the need fo...
SCOPE
1.1 Detergents play a critical role in the cleaning of clinically-used medical devices, but there are few consensus methods for describing the key characteristics of these detergents. This guide identifies consensus standards, ASTM and others, used to characterize detergents in other applications, which can also be used to characterize detergents used to clean clinically-used medical devices.  
1.2 In identifying these test methods, manufacturers of detergents can reference this guide to characterize their detergents.  
1.3 By identifying applicable test methods, gaps may be identified where development of new standardized test methods need to be developed to characterize detergents intended to clean medical devices.  
1.4 By identifying applicable test methods that are used and results reported by detergent manufacturers, test results can be shared and may lead in the future to development of performance criteria for the key characteristics of detergent.  
1.5 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.6 Exclusions:  
1.6.1 This guide is not intended for detergents formulated to remove residues as a result of the manufacturing process.  
1.6.2 This guide does not provide information related to disinfection or disinfecting agents that might be part of a detergent formulation.  
1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the Worl...

SIGNIFICANCE AND USE
3.1 The guide, as now constituted, is not suitable for ranking of hand dishwashing products, since no basis is available at this time for correlation of the foam stability of these products using any particular food soil or combination of soils with consumers' ranking of performance.  
3.2 The relative foam stability ranking of hand dishwashing detergent products will vary greatly depending on the type of food soils used in the test. Therefore, selection of the standard food soil to be used in a test shall be made by agreement between the interested parties on the basis of experience.  
3.3 This laboratory screening guide includes flexibility in several areas so as to allow its use by the maximum number of laboratories, without purchase of significant additional equipment. It should be recognized, therefore, that differences in specific equipment may result in a reduced level of interlaboratory and inter-operator precision, and such results must be evaluated with caution.
SCOPE
1.1 This guide provides guidelines for several techniques of measuring the foam stability of light-duty hand dishwashing detergent products in the presence of artificially applied test-food soils. It is intended as a laboratory screening test to aid in the formulation of products, for quality control and as a basis between the formulator and supplier in standardizing foam stability of the detergents.  
1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

SIGNIFICANCE AND USE
3.1 The cloud point temperature is a reproducible characteristic of certain  pure  nonionic surfactants. It is also characteristic of certain nonionic surfactant formulated systems. This test method is appropriate for both systems.
Note 1: If the transition from a distinctly cloudy to a clear solution is not sharp, that is, if it does not take place within a range of 1 °C, this test method is not appropriate.
SCOPE
1.1 This test method covers a procedure to determine the “cloud point” of nonionic surfactants or detergent systems. Cloud Point is the temperature at which dissolved components (solids or liquids) are no longer completely soluble, precipating as a second phase giving the fluid a cloudy appearance. It is limited to those surfactants and detergent systems for which the visible solubility change occurs over a range of 1 °C or less at concentrations of 0.5 % to 1.0 % in DI water between 30 °C and 95 °C.  
1.2 Chemical Limitations—Nonionic surfactants that exhibit a characteristic cloud point in general terms consist of a water-in-soluble moiety condensed with 50 % to 75 % by weight of ethylene oxide. If the level of ethoxylation is too low the surfactant may not be water soluble at temperatures less than 30 °C, and if it is too high no cloud point may exist.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
These test methods detail the standard procedures for the chemical analysis of soaps containing synthetic detergents. The analytical procedures include the determination of the following chemical properties and substances: moisture and other matter volatile at a specified temperature; free alkali or free acid; anhydrous, salt-free soda soap; alcohol-soluble matter; matter insoluble in water; total alkalinity of matter insoluble in alcohol (alkaline salts); sodium silicate; phosphates; phosphates by colorimetric method using molybdenum blue); unsaponified and unsaponifiable matter; free fatty matter; chlorides in alcohol-soluble matter; rosin by McNicoll method; synthetic detergent by difference; and neutral inorganic salts.
SCOPE
1.1 These test methods cover procedures for the chemical analysis of soaps containing synthetic detergents.  
1.2 The analytical procedures appear in the following order:    
Sections  
Moisture and Other Matter Volatile at 105°C (Oven Method)  
5 and 6  
Free Alkali or Free Acid  
7 and 8  
Anhydrous, Salt-Free, Soda Soap  
9 – 12  
Alcohol-Soluble Matter  
13 and 14  
Matter Insoluble in Water  
15 and 15  
Total Alkalinity of Matter Insoluble in Alcohol (Alkaline Salts)  
16 and 17  
Sodium Silicate  
18 – 20  
Phosphates  
21 – 28  
Phosphate (Colorimetric Method Using Molybdenum Blue)  
29 – 34  
Unsaponified and Unsaponifiable Matter  
35 – 39  
Free Fatty Matter  
40  
Chlorides in Alcohol-Soluble Matter  
41 – 43  
Rosin (McNicoll Method)  
44 – 47  
Synthetic Detergent (by Difference)  
48  
Neutral, Inorganic Salts  
49  
1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.4 This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

SIGNIFICANCE AND USE
3.1 This test method assures that the particle size of soaps and detergents conforms to specifications having to do with density and packaging, among others. It also offers a means of controlling the amount of potentially hazardous very low particle size material.
SCOPE
1.1 This test method covers the determination of the particle size of soaps and other detergents by hand sieving and machine sieving methods.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Material Safety Data Sheets are available for reagents and materials. Review them for hazards prior to usage.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
These test methods cover the sampling and chemical analysis of paste, powder, or liquid detergent fatty alkyl sulfates. The different procedure for sampling and chemical analysis of past, powder, or liquid detergent are presented and discussed in details. Distillation test, titration test, and gravimetric test shall be performed to meet the requirements prescribed. The calculations methods for chlorides as sodium chloride are presented in details.
SCOPE
1.1 These test methods cover the sampling and chemical analysis of paste, powder, or liquid detergent fatty alkyl sulfates.  
1.2 The procedures for sampling and analysis appear in the following order:    
Sections  
Sampling:  
Powders and Flakes Packed in Cans or Cartons  
4  
Powders and Flakes in Bulk  
5  
Liquids  
6  
Pastes  
7  
Preparation of Sample  
8  
Moisture by the Distillation Test Method  
11 – 14  
pH  
15  
Alkalinity  
16 – 19  
Alcohol-Soluble Matter  
20 – 22  
Alcohol-Insoluble Matter  
23 and 24  
Unsulfated Material  
25 – 28  
Combined Alcohols  
29 – 32  
Ester SO3:  
Method A. Titration Test Method  
36 and 37    
Sections  
Ester SO3:  
Method B. Gravimetric Test Method  
38 and 39  
Sodium Sulfate  
40 – 43  
Chlorides Calculated as Sodium Chloride (NaCl)  
44 – 47  
1.3 The values stated in either inch-pound or SI units are to be regarded separately as the standard. The values given in parentheses are for information only.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Material Safety Data Sheets are available for reagents and materials. Review them for hazards prior to usage.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
These test methods cover procedures for the sampling and chemical analysis of inorganic alkaline detergents. These detergents include caustic soda, soda ash, modified soda (sequicarbonate type), sodium bicarbonate, sodium metasilicate, trisodium phosphate, tetrasodium pyrophosphate, borax, and sodium triphosphate. Different tests shall be conducted in order to determine the following properties of the detergents: total alkalinity, matter insoluble in water content, apparent density, ignition loss, pH level, turbidity, temperature rise, and particle size. Chemical analysis of the samples shall be performed by using either reverse-flow ion-exchange chromatography or paper chromatography.
SCOPE
1.1 These test methods cover procedures for the sampling and chemical analysis of inorganic alkaline detergents.  
1.2 The procedures appear in the following order:    
Sections  
Caustic Soda:  
Sampling  
5  
Total Alkalinity as Sodium Oxide (Na2O)  
6 – 8  
Sodium Hydroxide (NaOH)  
9 – 11  
Carbonate as Sodium Carbonate (Na2CO3)  
12  
Carbon Dioxide (CO2) by the Evolution Method  
13 – 16  
Soda Ash:  
Sampling  
17  
Matter Volatile at 150 °C to 155 °C  
18 and 19  
Total Alkalinity as Sodium Carbonate (Na2CO3 )  
20 – 22  
Sodium Bicarbonate (NaHCO3)  
23 – 25  
Sodium Bicarbonate (NaHCO3) by Potentiometric Titration  
26 – 28  
Matter Insoluble in Water  
29 and 30  
Apparent Density  
31 and 32  
Modified Soda (Sequicarbonate Type):  
Sampling  
33  
Total Alkalinity as Sodium Oxide (Na2O)  
34 – 36  
Sodium Bicarbonate (NaHCO3) and Sodium Carbonate (Na2CO3)  
37 – 39  
Matter Insoluble in Water  
40  
Sodium Bicarbonate:  
Sampling  
41  
Sodium Bicarbonate, Sodium Carbonate, and Free Moisture  
42 – 45  
Matter Insoluble in Water  
46  
Sodium Metasilicate, Sodium Sesquisilicate and Sodium Orthosil- icate:  
Sampling  
47  
Total Alkalinity as Sodium Oxide (Na2O)  
48 – 50  
Total Silica as SiO2  
51 – 53  
Sodium Metasilicate (Na2SiO3·5H2O)  
54  
Sodium Sesquisilicate (3Na2O·2SiO2·11H2O)  
55  
Matter Insoluble in Water  
56 and 57  
Loss on Ignition of Sodium Sesquisilicate (3Na2O·2SiO2 ·11H2O)  
58 and 59  
Sodium Orthosilicate (Na4SiO4)  
60  
Trisodium Phosphate:  
Sampling  
61  
Trisodium Phosphate (Na3PO4) Content and Phosphorus Pentoxide (P2O5)  
62 – 64  
Trisodium Phosphate Calculated as Na3PO4·12H2O, Na3PO4· H2O, Na3PO4, and as P2O5  
65 – 68  
Total Alkalinity as Sodium Oxide (Na2O)  
69 – 71  
Matter Insoluble in Water  
72 and 73  
Tetrasodium Pyrophosphate:  
Sampling  
74  
Tetrasodium Pyrophosphate
(Na4P2O7)  
75 – 79  
Matter Insoluble in Water  
80 and 81  
Loss on Ignition  
82 and 83  
Borax:  
Sampling  
84  
Total Borate and Excess Alkalinity or Acidity  
85 – 87  
Matter Insoluble in Water  
88 and 89  
Sodium Triphosphate:  
Sampling  
90  
Tritratable Na2O  
91 – 94  
Total P2O5:  
Preferred Method  
95 – 97  
Alternative Method  
98 – 101  
pH Titration  
102 – 107  
Quantitative Separation and Measurement of Various Phosphates:  
Reverse-Flow Ion-Exchange Chromatography (Preferred Method)  
108 – 119  
Paper Chromatographic Method  
120 – 127  
pH of 1 percent Solution  
128  
Turbidity  
129  
Temperature Rise  
130 – 134  
Sulfate  
135 – 137  
Ignition Loss  
140 and 141  
Matter Insoluble in Water  
142 – 144  
Particle Size  
145  
Orthophosphate  
146 – 151  
1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of th...

ABSTRACT
This test method covers the determination of foaming properties of surface-active agents. Glass tubing apparatus for this test method shall include pipet and a receiver. Apparatus requirements like dimensions, shape, calibration marks, rubber stoppers, etc., shall conform to the specifications as indicated in this standard method. Test solution preparation shall include water preheating, adding the surface-active agent while stirring, and solution aging. Test procedure for foaming properties determination shall be done while surface-active solution is aging as indicated in this standard test method. Report shall include test solution concentration, temperature, water hardness, and foam height.
SCOPE
1.1 This test method covers the determination of the foaming properties of surface-active agents as defined in Terminology D459. This test method is applicable under limited and controlled conditions, but does not necessarily yield information correlating with specific end uses. This method is subjected to the operator of the method as the foam heights are not always level and an average height is determined by the user so it is more of a qualitative measurement in these instances. However, for foam measurements results taken on more flat uniform samples this method has more of a quantitative quality.  
1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
These test methods cover the chemical analysis of sulfonated and sulfated oils. Water by distillation with volatile solvent and moisture and volatile matter by hot-plate shall be tested to meet the requirements prescribed. Titration test, extraction-titration test, and ash-gravimetric test shall be performed to meet the requirements specified. Total desulfated fatty matter, total active ingredients, unsaponifiable non-volatile matter, inorganic salts, total alkalinity, and total ammonia shall be tested to meet the requirements prescribed. In the absence of ammonium or triethanolamine soaps test method, brine test method, and in the presence of ammonium or triethanolamine soaps test method shall be performed to meet the requirements prescribed. Water-immiscible organic solvents volatile with steam shall be tested to meet the requirements prescribed.
SCOPE
1.1 These test methods cover the chemical analysis of sulfonated and sulfated oils. The analytical procedures appear in the following order:    
Section  
Moisture:  
Test Method A. Water by Distillation with Volatile Solvent  
4 – 9  
Test Method B. Moisture and Volatile Matter by Hot-Plate Method  
10 – 14  
Organically Combined Sulfuric Anhydride:  
Test Method A. Titration Test  
15 – 19  
Test Method B. Extraction-Titration Test  
20 – 24  
Test Method C. Ash-Gravimetric Test (in the Presence of True
Sulfonates)  
25 – 28  
Total Desulfated Fatty Matter  
29 – 32  
Total Active Ingredients  
33 – 36  
Unsaponifiable Nonvolatile Matter  
37 – 41  
Inorganic Salts  
42 – 46  
Total Alkalinity  
47 – 49  
Total Ammonia  
50 – 52  
Acidity as Free Fatty Acids or Acid Number:  
Test Method A. In the Absence of Ammonium or Triethanolamine Soaps  
53 – 56  
Test Method B. In the Presence of Dark Colored Oils but in the
Absence of Ammonium or Triethanolamine Soaps (Brine Test)  
57 – 60  
Test Method C. In the Presence of Ammonium or Triethanolamine Soaps  
61 – 63  
Water-Immiscible Organic Solvents Volatile with Steam  
64 – 70  
1.2 The values stated in inch-pound units are to be regarded as the standard. The metric equivalents of inch-pound units may be approximate.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Material Safety Data Sheets are available for reagents and materials. Review them for hazards prior to usage.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

SIGNIFICANCE AND USE
3.1 This test method is intended as a laboratory screening test to determine performance of the detergent under actual use conditions, but will not necessarily predict performance under all end-use conditions.
SCOPE
1.1 This guide covers a procedure for measuring performance of a mechanical dishwashing detergent in terms of the buildup of spots and film on glassware. It is designed to evaluate household automatic dishwasher detergents but can be used as a screening test for institutional and commercial dishwashing products.  
1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

SIGNIFICANCE AND USE
5.1 This guide suggests a number of staining agents that are representative of stains commonly encountered in household laundry. The assessment need not be limited to this suggested list of stains, especially if special product types or end uses are being evaluated. This guide can be used to compare stain removal performance of products; however, there is no confirmed basis for correlation of this controlled laboratory technique with consumers’ ranking of stain removal performance.  
5.2 The evaluations generated by this guide should be regarded as diagnostic screening tests that are useful in formulation studies, quality control, and ingredient raw material qualification. This guide provides considerable flexibility in choosing specific stains, washing conditions, and laboratory equipment appropriate to the objective of the evaluation. This procedural latitude may result in a reduced level of interlaboratory precision and such comparison of results must be evaluated with caution.  
5.3 The procedure is applicable to all types of home laundry products including detergents, presoak and prespotter products, bleaches, and detergent boosters and is expected to be applicable to horizontal and vertical axis machines.  
5.4 It is not intended for the evaluation of products or conditions normally associated with commercial laundering or dry cleaning establishments.
SCOPE
1.1 This is a guide for evaluating stain removal performance of home laundry products or home laundering conditions. It provides guidance for the selection, preparation, application, and examination of various types of stains on test fabrics that are subjected to controlled but practical stain removal treatment conditions.  
1.2 There is no single combination of stain and fabric that will predict the overall performance of a product or treatment method. A single test, even with a variety of stains/fabrics, can only predict how products or treatment methods compare under the particular conditions chosen for evaluations. A series of assessments is necessary to evaluate the many aspects of stain removal performance and to simulate consumer experience more closely.  
1.3 In this guide, the use of both traditional top-loader washing machines as well as front and top-loading high-efficiency washers is addressed.  
1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This guide covers the evaluation of the effect of dyestuff color transfer or color loss from dyed fabrics. It is designed as a laboratory screening test to aid in the formulation of detergent products or the comparison of two or more detergents, it is not suitable for detergent or washing machine rankings. The apparatus and materials use in evaluating color transfer or color loss of dyed fabrics are presented in details. The procedure for color transfer in one wash, and color loss in three washes are presented in details.
SCOPE
1.1 This guide covers the evaluation of the effect of dyestuff color transfer or color loss from dyed fabrics. It is designed as a laboratory screening test to aid in the formulation of detergent products or the comparison of two or more detergents.  
1.2 There is no single assessment that will give the overall performance of a laundry product. A single test can only suggest how a formulation performs under the particular conditions chosen for the evaluation and cannot be expected to reflect comparative product performance under the many other possible conditions of use. A series of assessments is always necessary in order to evaluate the many aspects of product performance. It is necessary to conduct confirming tests under controlled but practical home-laundering conditions to simulate consumer experience.  
1.3 The values stated in either inch-pound or SI units are to be regarded separately as the standard. The values given in parentheses are for information only.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

SIGNIFICANCE AND USE
4.1 Significance—Dried blood represents a significant challenge to cleaning surgical instruments. The water-soluble components of blood are easily rendered insoluble when exposed to heat, chemical solutions, or time at room temperature. The water insoluble component of blood is fibrin built up during coagulation. These proteins bind quite readily to the surfaces of surgical instruments making them difficult to remove even with the aid of chemical cleaning agents. Instruments contaminated with blood residue after reprocessing represent a significant threat for infection to healthcare workers and patients. Healthcare facilities typically employ the use of automated instrument washers. These devices combine mechanical action along with chemical cleaning agents in a staged cleaning cycle designed to thoroughly clean surgical instruments. To function properly, these machines must be performing at targeted mechanical efficiency and deliver the correct chemical cleaning agents at the correct temperature, at the correct dosage for the correct period of time. Manufacturers of automated washers and manufacturers of cleaning detergent need to evaluate the performance of their products utilizing a surrogate for surgical instruments soiled with blood. The results of the performance testing will be used to improve product design and for validation of the performance of their product for various regulatory requirements.  
4.2 Use—The regular, periodic use of the blood soil test is a systemic challenge to the functioning of an automated washer. To properly challenge the cleaning device, the test must be analogous to the dried blood soil, to the stainless steel substrate, and to the physical barriers presented by surgical instruments. These physical barriers include the box lock, or pivot joint of a hinged instrument, the serrated tips, and crevices of surgical instruments. On the test coupon, the components of blood are similar to the state of dried blood on instruments. By utiliz...
SCOPE
1.1 This guide is based on a standardized test soil correlating to coagulated blood suitable for screening tests and the evaluation of the cleaning efficiency of washer-disinfectors used for reprocessing of surgical instruments. This guide strictly deals with cleaning and does not describe any methods that are related to disinfection. See Referenced Documents D5343, D4008, D4265, D2960, and D3050 in Section 2 for additional information.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

SIGNIFICANCE AND USE
5.1 This guide suggests methodology for cleaning tests. This methodology can only be applied to assess product performance on typical bathroom soils and is not inclusive of all potential soils present on ceramic tiles or other bathroom surfaces. An assessment of cleaning performance on surfaces other than ceramic tile cannot be presumed since there is no confirmed basis for correlation for this soil on other surface or substrate types.  
5.2 The results of tests based on this guide are regarded as diagnostic screening values useful in formulation studies, quality control, and ingredient raw material qualification. The results of this guide should be compared to control treatments, which are incorporated into each performance evaluation. These results should be considered to be relative to all other treatments in the study and are not absolute values. For interlaboratory comparisons, exact treatment conditions must be established and then results should be compared as relative ranking to the control treatments rather than as absolute values.  
5.3 This guide is applicable to testing all types of multi-purpose household and bathroom cleaners, whether the detergent is prepared by dissolving a soluble powder, a dilutable liquid, or is a non-dilutable product. It may also be useful for evaluation of products or conditions normally associated with industrial or institutional cleaners.
SCOPE
1.1 This guide covers the evaluation of the cleaning performance of products intended for use on ceramic tiles. This guide provides techniques for soiling, cleaning, and evaluating performance of detergent systems under controlled, but practical, hard-surface cleaning conditions.  
Note 1: The soils described in this guide are known in the industry as “soap scum.”  
1.2 Such systems include any detergent, cleaner, or abrasive cleanser intended for cleaning hard surfaces composed of ceramic tile. This guide is not appropriate for evaluating performance on grout. This guide also excludes other surfaces such as glass, resilient flooring, synthetic countertop surfaces or washable wall surfaces. The products for which this guide is intended include solutions of soluble powdered detergent, dilutions of concentrated liquid detergent, or products intended to be used full strength, for example, foams, sprays, liquid, wipes, powders, or paste.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Material Safety Data Sheets are available for reagents. Review them for hazards prior to usage.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

SIGNIFICANCE AND USE
5.1 This test method is used to determine the percent actives in each type of the disinfectant quaternary ammonium salts, and also in the disinfectant products. Quaternary ammonium compounds being the active ingredients in disinfectant-type products require accurate determination to assess the cost and antimicrobial performance of such products.
SCOPE
1.1 This test method covers a potentiometric titration procedure for determining active matter in disinfectant quaternary ammonium salts. This test method is intended for the analysis of quaternary ammonium salts used as disinfectants, and only applies to the following commonly used quaternary ammonium salts: n-alkyldimethylbenzylammonium chloride (see Fig. 1), cetyltrimethylammonium chloride, and a blend of n-octyldecyl dimethylammonium chloride, di-n-octyl dimethylammonium chloride, and di-n-decyldimethyl ammonium chloride (see Fig. 2). Also, this test method can be applied to the analysis of disinfectant type products where the formula ingredients are known and the quaternary ammonium salt is one of the above. Interferences such as amines oxides and betaines present in disinfectant formulations were not tested.  X−  =  chloride, and    R  =  aliphatic, normal C8 − C22.    
1.2 This disinfectant quaternary ammonium salt conforms to the structures in Fig. 1 and Fig. 2.  
1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific precautionary information, see Section 8.

ABSTRACT
This test method covers the determination of ethylene oxide content in polyethoxylated nonionic surfactants. It can also be used for compounds containing propylene oxide or any compounds (glycols and glycol and polyglycol ethers and esters) which form unstable 1,2-diiodides on reaction with hydroiodic acid. The apparatus is comprised of the following: heat source which shall be an electric heater provided with a sliding rheostat or other means of heat control; flasks which shall be equipped with a standard ground-glass joint; condensers with standard joints; gas bubbler filled with dibutyl phthalate; buret; and pipet. The dual apparatus is designed to permit a sample and a blank to be run simultaneously. Reagent grade chemicals or reagents of sufficiently high purity including water, carbon dioxide or nitrogen, lubricant, dibutyl phthalate, glass beads, hydroiodic acid, hydrochloric acid, methanol, potassium dichromate, potassium iodide solution, sodium thiosulfate, and starch indicator solution shall be used in all tests. The ethylene oxide content shall be calculated from the amount of sodium thiosulfate solution required to titrate the sample and the blank, normality of sodium thiosulfate, and weight of the sample. Standard deviations for repeatability and reproducibility shall be estimated to determine the acceptability of the results.
SCOPE
1.1 This test method covers the determination of ethylene oxide in polyethoxylated nonionic surfactants. It can also be used for compounds containing propylene oxide or any compounds (glycols and glycol and polyglycol ethers and esters) which form unstable 1,2-diiodides on reaction with hydriodic acid.  
Note 1: Compounds in which the oxyalkylene group is connected to a nitrogen cannot be entirely decomposed. This can be used to determine the percent of an ethoxylated surfactant in a mixture, if the ethylene oxide content of the ethoxylated surfactant is known.
Note 2: This method reports results as percent ethylene oxide. If this method is applied to unknown compounds or compositions, the analyst should be aware of the possible presence of material other than ethylene oxide.
Note 3: For use on built syndet compositions the organic active ingredient must be isolated in accordance with Test Method D2358.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Material Safety Data Sheets are available for reagents and materials. Review them for hazards prior to usage.

ABSTRACT
This test method covers the determination of inorganic active oxygen in bleaching compounds such as perborates, percarbonates, and peroxides by titration of an acidified aqueous solution with a standard solution of potassium permanganate. Tests shall use reagent grade chemicals, reagent water, potassium permanganate standard solution, sodium oxalate, and sulfuric acid. Well mixed sample shall be titrated according to the procedure indicated in this standard method. Active oxygen weight percent shall be calculated using the given formula.
SCOPE
1.1 This test method covers the determination of inorganic“ active oxygen” in bleaching compounds such as perborates, percarbonates, and peroxides but not in persulfates or monopersulfates.  
1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Safety Data Sheets (formerly known as Material Safety Data Sheets) are available for reagents and materials. Review them for hazards prior to usage.

SIGNIFICANCE AND USE
4.1 Alkylbenzene sulfonic acids are important intermediates in the synthetic detergent industry and are defined under “alkyl benzene sulfonate” in Terminology D459. This test method is suitable for the rapid monitoring of the sulfonic and sulfuric acid levels, both of which have a vital bearing on final product performance and appearance.
SCOPE
1.1 This test method is applicable to the determination of sulfonic and sulfuric acids in branched and linear alkylbenzene sulfonic acids used as intermediates in synthetic detergents.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Material Safety Data Sheets are available for reagents and materials. Review them for hazards prior to usage.

SIGNIFICANCE AND USE
3.1 Alcohol ethoxylates and alkylphenol ethoxylates are important surfactants in household and industrial cleaners. They may be used as either nonionic surfactants or sulfated and used as anionic surfactants. Careful control of the ethoxylate characteristics is desired as variations may result in either desirable or undesirable end-use properties.
SCOPE
1.1 These test methods cover the various test methods used to evaluate those properties pertinent to the characterization of alcohol ethoxylates and alkylphenol ethoxylates with respect to suitability for desired uses.  
1.2 The procedures for sampling and analysis appear in the following order:    
Sections  
Sampling  
Liquids  
6  
Solids  
7  
Methods of Chemical Analysis  
Water or moisture  
8  
Refractive index  
9 and 10  
pH  
11  
Acidity or basicity  
12 and 13  
Hydroxyl number  
14 – 20  
Cloud point  
21  
Iodine number  
22  
Ash  
23  
Iron  
24  
Ethylene oxide content  
25  
Polyethylene glycols  
26 – 32  
1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Material Safety Data Sheets are available for reagents and materials. Review them for hazards prior to usage. Specific hazard statements appear in Section 5 and Note 1 and Note 3.

SIGNIFICANCE AND USE
4.1 This test method is suitable in research, development, and manufacturing control to monitor the level of citrate, a sequestering agent, in powder and liquid detergents.  
4.2 Accurate determination of sequestering agent is important in evaluating cost and performance of detergent products.
SCOPE
1.1 This test method covers a potentiometric titration procedure for the determination of citrate in liquid and powder detergents.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Material Safety Data Sheets are available for reagents and materials. Review them for hazards prior to usage. Specific safety precautions are given in Section 8.

ABSTRACT
This test method covers atomic absorption tests applicable to powdered laundry detergents containing clay and zeolite. The test sample is fused with lithium metaborate, dissolved in acid, its silicon and aluminum content measured by atomic absorption, and the silicon/aluminum (Si/Al) ratio calculated. The clay and zeolite content of the test sample is calculated from the Si/Al ratio of the test sample and the Si/Al ratio of the clay and zeolite expected in the test sample. This test method is based on the linear relationship between the relative composition (or ratio) of clay/zeolite in detergent powders and the Si/Al ratio of such detergents.
SCOPE
1.1 This test method covers atomic absorption tests applicable to powdered laundry detergents containing clay and zeolite.2  
1.2 The values stated in SI units are to be regarded as the standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ABSTRACT
This test method covers the determination of ethylene diamine tetraacetate (EDTA) in soaps and synthetic detergents. Throughout this test method EDTA represents the hydrated disodium salt containing 2 moles of H 2
SCOPE
1.1 This test method covers the determination of ethylene diamine tetraacetate (EDTA) in soaps and synthetic detergents. Throughout this test method EDTA represents the hydrated disodium salt containing 2 moles of H2O. In the chemical literature this is frequently abbreviated to Na2H2Y4 · 2H2O.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Material Safety Data Sheets are available for reagents and materials. Review them for hazards prior to usage.

SIGNIFICANCE AND USE
3.1 These test methods are suitable for setting specifications on linear detergent alkylates and for quality control where these alkylates are manufactured or are used in a manufacturing process.  
3.2 The gas chromatography test is useful in identifying linear detergent alkylates produced by the various manufacturing processes and for determining the applicability of a linear detergent alkylate to a particular end use. Test conditions have been optimized for resolution of the C-9 to C-15 linear detergent alkylates and the presence of higher or lower chain lengths will be readily apparent but may produce erroneous results. The tetralin structures have not been sufficiently identified to allow determination of tetralins, and small unidentified components are reported as tetralins and unidentifieds.  
3.3 Some linear detergent alkylates use a manufacturing process with an organic chloride as a precursor. This test may be used to ensure that the chloride content of the alkylate is not excessive for a particular end use.  
3.4 The platinum-cobalt color test is useful in determining that the color of the linear detergent alkylate will not contribute to the color of the end use product.  
3.5 The refractive index and specific gravity tests are possible aids in the identification of linear detergent alkylates and in evaluating alkylates for gross contaminants.  
3.6 The water test is suitable for determining that linear detergent alkylates do not contain amounts of water deleterious to further processing.
SCOPE
1.1 These test methods cover chemical and physical tests applicable to linear detergent alkylates, evaluating those properties which characterize linear detergent alkylates with respect to its suitability for desired uses.  
Note 1: Linear detergent alkylates comprises linear alkylbenzenes prepared by varying processes of varying linear alkyl chain length. The alkylate is sulfonated for surfactant use, the largest application being in detergent products. Careful control of linear detergent alkylate characteristics is desired; during sulfonation, variations of the sulfonate can occur that may result in either desirable or undesirable end-use properties.  
1.2 The test methods appear as follows:    
Section  
Composition by Gas Chromatography  
7 – 15  
Chlorides  
16 – 27  
Color  
28 – 30  
Refractive Index  
31 – 33  
Specific Gravity  
34 – 36  
Water  
37 – 39  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Material Safety Data Sheets are available for reagents and materials. Review them for hazards prior to usage. See also Note 1 and Section 21.

ABSTRACT
This specification covers sodium bicarbonate for use in various washing, cleaning, and scouring processes. As received sodium bicarbonate shall conform to the chemical requirements according to this specification. Sodium bicarbonate shall be a white, uniform powder, and caking shall be readily disintegrated. Sampling and chemical analysis shall be in accordance with the ASTM standard test methods of alkaline detergents.
SCOPE
1.1 This specification covers material suitable for use in various washing, cleaning, and scouring processes, with or without soap as conditions demand, and where a mildly alkaline material is desired. (Warning—This material may be hazardous if not properly managed. Precautionary information for the safe use, storage, and disposal of this material should be preliminarily obtained from suppliers and others. In case of personal accident with this material, apply appropriate first aid; telephone nearest Poison Control Center for assistance, and get medical attention immediately.)

SIGNIFICANCE AND USE
3.1 This test method is suitable in research, development, and manufacturing control to monitor the level of NTA, a sequestering agent, in powder and liquid detergents.  
3.2 Accurate determination of a sequestering agent is important in evaluating cost and performance of detergent products.
SCOPE
1.1 This test method describes the determination of nitrilotriacetates (NTA) in detergents.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific safety precautions, see 6.5.

SIGNIFICANCE AND USE
33.1 This method is suitable as a quality control test for the measurement of color in alpha olefin sulfonates.
SCOPE
1.1 These test methods cover the chemical analysis of alpha olefin sulfonates. The analytical procedures appear in the following order:
Sections  
Moisture by the Distillation Method  
4 – 8  
Sodium Sulfate  
9 – 14  
Neutral Oil  
15 – 19  
Chlorides Calculated as Sodium Chloride (NaCl)  
20 – 24  
Alkalinity  
25 – 29  
pH  
30 and 31  
Determination of Color  
32 – 37  
Determination of Active Content by Methylene Blue Titration  
38 – 47  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific precaution statement see 36.1. Material safety data sheets are available for reagents and materials. Review them for hazards prior to usage.

SIGNIFICANCE AND USE
4.1 This test method is of use to anyone engaged in compositional analysis of detergent formulations. This would include formulators, and analysts employed by companies that manufacture the components usually included in such formulations.
SCOPE
1.1 This test method covers the analysis for the apparent sodium toluene sulfonate (NaTS) content of detergents.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Material Safety Data sheets are available for reagents and materials. Review them for hazards prior to usage.

SCOPE
1.1 This terminology covers soaps and other detergents.

SIGNIFICANCE AND USE
4.1 This test method offers a means of determining anionic detergents commonly found in laundry, dishwashing, and other cleaning materials. Accurate determination of the anionic active substance is highly important in assessing the cost and effectiveness of such cleaning substances.  
4.2 This test method is not affected by low molecular weight sulfonates, such as those of toluene and xylene commonly found in detergent formulations, when these substances are present up to 15 weight % of active material.
SCOPE
1.1 This test method covers the determination of the amount of synthetic anionic ingredient in a surfactant by direct titration with a standardized cationic reagent. The test method is a simple and convenient means for the quantitative estimation of the anionic material. The end point is detected by the transfer of a colored complex from an organic solvent phase to an aqueous phase. The colored complex is formed by the addition of a solution of dye to a solution of the anionic surfactant. This complex is soluble in the organic-solvent phase and insoluble in the aqueous phase. When this solution is titrated with a standardized solution of a cationic reagent, the dye is displaced from the colored complex and, being water-soluble, migrates to the aqueous phase. Therefore, a cationic titrating solution that has been standardized against a characterized anionic agent can be used to analyze for other anionics of known molecular mass.  
1.2 This test method is applicable to alkylaryl sulfonates, alkyl sulfonates, alkyl sulfates and hydroxy-sulfates, alkylphenol- and fatty alcohol ethoxy-sulfates and dialkylsulfosuccinates. It applies to active materials containing one hydrophilic group per molecule.  
1.3 The analytical procedures appear in the following order:    
Sections  
Reagents  
6    
Primary Standard  
8    
Purity  
8.2  
Alcohols  
8.3  
Free Acid or Alkali  
8.4  
Preparation of Mixed Indicator Solution  
9    
Preparation of Hyamine Solution  
10    
Standardization of Hyamine Solution  
11    
General Procedure for Anionic-Active Material  
12  
1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. A precautionary statement appears in Section 7. Material Safety Data Sheets are available for reagents and materials. Review them for hazards prior to usage.

ABSTRACT
This test method covers the procedure for the separation and purification of active ingredient from surfactants and syndet compositions. The separated active ingredient may be used for qualitative examinations. The method also permits the estimation of total active ingredient level present in the sample under test. The method method yields the active ingredient together with other alcohol-soluble materials and therefore is useful only in estimating the actual active ingredient level.
SCOPE
1.1 This test method covers the procedure for the separation and purification of active ingredient from surfactants and syndet compositions. The separated active ingredient may be used for qualitative examinations. This test method also permits the estimation of total active ingredient level present in the sample under test.  
1.2 This test method yields the active ingredient together with other alcohol-soluble materials and therefore is useful only in estimating the actual active ingredient level. Correction for the amount of the most common contaminant, sodium chloride, is shown by a separate determination.  
1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Material Safety Data Sheets are available for reagents and materials. Review them for hazards prior to usage.

SIGNIFICANCE AND USE
5.1 Anionic surfactants are the most widely used of the synthetic detergents. ASTM methods in current use for their determination involve two-phase aqueous/chloroform titrations with the organic dyes methylene blue (Test Method D1681) or disulphine blue/dimidium bromide (Test Method D3049) as indicators. One advantage of the potentiometric method is that it eliminates the use of chloroform whose use is restricted for environmental and toxicological reasons.  
5.2 This test method is intended for use as described in 1.1.
SCOPE
1.1 This test method describes a potentiometric titration procedure for determining the anionic active matter in detergents. It is intended for the analysis of anionic surfactants such as detergent range alkylbenzenesulfonates, α-olefin sulfonates, alcohol sulfates, and alcohol ethosulfates. It has not been tested for surfactant formulations.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Material Safety Data Sheets are available for reagents and materials. Review them for hazards prior to usage.  (A) Methylene blue method.(B) Mixed indicator method.

ABSTRACT
This test method covers commercial synthetic detergents and built detergent formulations that do not contain organic additives such as amides. This test method involves measurement of the ultraviolet absorbance of the sample at the maximum absorbance point for sodium alkylbenzene sulfonate and at a selected background point in order to determine the amount of active ingredient present. The percentage of alcohol-soluble matter, absorptivity value and percentage of active ingredient shall be calculated in accordance to the specified requirements.
SCOPE
1.1 This test method covers commercial synthetic detergents and built detergent formulations that do not contain organic additives such as amides. Optical dyes and materials normally found in formulated detergents do not interfere; however, materials other than sulfonates that possess strong ultraviolet absorptions must be absent. The indicated sample size and aliquoting scheme is based on samples containing 30 to 40% of active ingredient.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Material Safety Data Sheets are available for reagents and materials. Review them for hazards prior to usage.

ABSTRACT
This test method covers the enzymatic determination of citrate in both liquid and solid synthetic detergents. The test method is applicable to most detergents containing citrate at a minimum concentration of approximately 5 %. The apparatus to be used in the determination of citrate shall includes interval timer, micropipet, and spectrophotometer. An enzyme system that is based upon the selective cleavage of citrate by citrate lyase (citrate oxaloacetate-lyase; EC 4.1.3.6) shall be employed. One of the products, oxaloacetate, shall be reduced to malate by malic dehydrogenase (L-malate: NAD oxidoreductase; EC 1.1.1.37) with the simultaneous oxidation of reduced (beta)-nicotinamide adenine dinucleotide to (beta)-nicotinamide adenine dinucleotide, oxidized form. The course of the reaction shall be measured spectrophotometrically. The decrease in absorbance at 340 nm caused by the formation of (beta)-nicotinamide adenine dinucleotide, oxidized form, is directly proportional to the concentration of citrate.
SCOPE
1.1 This test method covers the enzymatic determination of citrate in both liquid and solid synthetic detergents. The test method is applicable to most detergents containing citrate at a minimum concentration of approximately 5 % (1-8).2  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Material Safety Data Sheets are available for reagents and materials. Review them for hazards prior to usage.

ABSTRACT
These test methods detail the standard procedures for the sampling and chemical analysis of chlorine-containing bleaches including sodium hypochlorite (soda bleach) solutions, calcium hypochlorite, and chloroisocyanuric acids and their derived salts. Tests for sodium hypochlorite include the determination of available chlorine, sodium chlorate, total chorine, sodium chloride, total alkalinity as sodium oxide, and free alkali as sodium hydroxide. Tests for calcium hypochlorite include the determination of available chlorine, and water. And finally, tests for chloroisocyanuric acids and their derived salts include the determination of available chlorine by iodometric-thiosulfate and arsenite-iodometric methods, and moisture.
SCOPE
1.1 These test methods cover the sampling and chemical analysis of chlorine-containing bleaches. The methods appear in the following order:    
Sections  
Sodium Hypochlorite (Soda Bleach) Solutions:  
Sampling  
5  
Available Chlorine  
6 – 9  
Sodium Chlorate  
10 – 14  
Total Chlorine  
15 – 18  
Sodium Chloride  
19 and 20  
Total Alkalinity as Sodium Oxide (Na2O)  
21 – 24  
Free Alkali as Sodium Hydroxide (NaOH)  
25 – 28  
Calcium Hypochlorite:  
Sampling  
30  
Available Chlorine  
31 – 34  
Water  
35 – 40  
Chloroisocyanuric Acids and Their Derived Salts:  
Sampling  
42  
Available Chlorine (Iodometric—Thiosulfate Method)  
43 – 46  
Available Chlorine (Arsenite—Iodometric Method)  
47 – 50  
Moisture  
51 – 54  
1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Material Safety Data Sheets are available for reagents and materials. Review them for hazards prior to usage.

ABSTRACT
This test method covers the assay of alkaline protease enzymes. This procedure is applicable to enzyme preparations with high activity but is inapplicable to formulated detergent products or air samples. The apparatus and reagents used in testing the assay for alkaline protease enzymes are presented.
SCOPE
1.1 This test method covers the assay of alkaline protease enzymes. This procedure is applicable to enzyme preparations with high activity but is inapplicable to formulated detergent products or air samples.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Material Safety Data Sheets are available for reagents and materials. Review them for hazards prior to usage.

SIGNIFICANCE AND USE
5.1 The guide can be used to compare anti-redeposition performance of products; however, there is no confirmed basis for correlation of this controlled laboratory technique with consumers’ ranking of anti-redeposition performance.
SCOPE
1.1 This guide provides direction for measuring the ability of detergents to prevent the deposition of soils from detergent solutions onto fabrics. It is intended as a laboratory screening test to aid in the formulation of detergent products, for quality control, and as a basis between the purchaser and seller in standardizing specific products' performance.  
1.2 The anti-soil deposition performance of detergent products will vary greatly depending on the type of soils and fabrics used in the test. Therefore, selection of the soils, fabrics, reference detergents, and test conditions shall be made by agreement between the interested parties on the basis of experience.  
1.3 There is no single or combination of oily soils or particulate soils, or both, that will precisely predict overall the performance of a product or treatment with respect to anti-redeposition as perceived by a consumer. This guide is intended to assess or compare detergent performance with respect to the anti-redeposition performance for the specific soil chosen.  
1.4 The values stated in either inch-pound or SI units are to be regarded separately as the standard. The values given in parentheses are for information only.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Material safety data sheets are available for reagents and materials. Review them for hazards prior to usage.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

SIGNIFICANCE AND USE
5.1 The methods in this guide can be used for screening of fabric softener products or to evaluate their performance, through a single cycle or multiple accumulative cycles, relative to a designated reference product or a comparative product(s).  
5.2 A single assessment of each of the product characteristics tested by these methods will not predict overall performance of the softener product. A single test run under specified fixed conditions cannot be expected to reflect the comparative performance under many other possible conditions of use.
SCOPE
1.1 This guide evaluates the performance characteristics of fabric softener products. It provides guidance for evaluating the on fabric efficacy of treatment chemicals dosed into the wash, rinse, or dryer cycle in a home laundry washer or dryer. This guide can be used for screening of fabric softener products, or to evaluate the products through multiple accumulative cycles.  
1.2 The relative ranking of products assessed by these procedures may be affected by such factors as machine type and settings, fabric load composition, as well as by the washing and drying procedures used.  
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

SIGNIFICANCE AND USE
5.1 A critical step in preparing a medical device for safe use on the next patient is effective cleaning. Typically cleaning a medical device includes precleaning at the point-of-use, manual and automated methods for removing soil that accumulate during clinical use. The cleaning solution(s) used are almost always water for rinsing and water with a detergent during washing. AAMI TIR34 (also EN 285) provides guidance about the quality of water to be used during reprocessing. This guidance references various test methods to ensure that water meets the recommended quality.  
5.2 When it comes to detergents very little guidance can be found in AAMI, ISO, ASTM, and FDA documents. Further, there are very few consensus methods for evaluating the detergents intended to clean medical devices. The result is that very little detail about detergents, for comparison purposes, is known. As a result, device manufacturers, when authoring their instructions for use (IFU) describe in very generic terms the kind of detergent that can be used to clean their device. Similarly, regulators, also have very little to rely upon for clearing reprocessing instructions. Finally, the healthcare facility, that is ultimately responsible for getting the device clean, has very little detail to assure that one brand of detergent is roughly equivalent to the one used by the medical device manufacturer during validation testing.  
5.3 While consensus standard test methods do not exist for detergents intended to clean medical devices, there are dozens of such test methods when it comes to detergents intended to clean dishes, laundry, floors, countertops, and so forth. Many of these methods are under the domain of ASTM D12: Soaps and other Cleaning Agents Including Detergents. While differences certainly do exist, essentially the detergents used for the other purposes are roughly formulated in the same way. Using existing test methods can drive detergent formulation development or determine the need fo...
SCOPE
1.1 Detergents play a critical role in the cleaning of clinically-used medical devices, but there are few consensus methods for describing the key characteristics of these detergents. This guide identifies consensus standards, ASTM and others, used to characterize detergents in other applications, which can also be used to characterize detergents used to clean clinically-used medical devices.  
1.2 In identifying these test methods, manufacturers of detergents can reference this guide to characterize their detergents.  
1.3 By identifying applicable test methods, gaps may be identified where development of new standardized test methods need to be developed to characterize detergents intended to clean medical devices.  
1.4 By identifying applicable test methods that are used and results reported by detergent manufacturers, test results can be shared and may lead in the future to development of performance criteria for the key characteristics of detergent.  
1.5 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.6 Exclusions:  
1.6.1 This guide is not intended for detergents formulated to remove residues as a result of the manufacturing process.  
1.6.2 This guide does not provide information related to disinfection or disinfecting agents that might be part of a detergent formulation.  
1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the Worl...

SIGNIFICANCE AND USE
3.1 The guide, as now constituted, is not suitable for ranking of hand dishwashing products, since no basis is available at this time for correlation of the foam stability of these products using any particular food soil or combination of soils with consumers' ranking of performance.  
3.2 The relative foam stability ranking of hand dishwashing detergent products will vary greatly depending on the type of food soils used in the test. Therefore, selection of the standard food soil to be used in a test shall be made by agreement between the interested parties on the basis of experience.  
3.3 This laboratory screening guide includes flexibility in several areas so as to allow its use by the maximum number of laboratories, without purchase of significant additional equipment. It should be recognized, therefore, that differences in specific equipment may result in a reduced level of interlaboratory and inter-operator precision, and such results must be evaluated with caution.
SCOPE
1.1 This guide provides guidelines for several techniques of measuring the foam stability of light-duty hand dishwashing detergent products in the presence of artificially applied test-food soils. It is intended as a laboratory screening test to aid in the formulation of products, for quality control and as a basis between the formulator and supplier in standardizing foam stability of the detergents.  
1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

SIGNIFICANCE AND USE
3.1 The cloud point temperature is a reproducible characteristic of certain  pure  nonionic surfactants. It is also characteristic of certain nonionic surfactant formulated systems. This test method is appropriate for both systems.
Note 1: If the transition from a distinctly cloudy to a clear solution is not sharp, that is, if it does not take place within a range of 1°C, this test method is not appropriate.
SCOPE
1.1 This test method covers a procedure to determine the “cloud point” of nonionic surfactants or detergent systems. Cloud Point is the temperature at which dissolved components (solids or liquids) are no longer completely soluble, precipating as a second phase giving the fluid a cloudy appearance. It is limited to those surfactants and detergent systems for which the visible solubility change occurs over a range of 1°C or less at concentrations of 0.5 to 1.0 % in DI water between 30 and 95°C.  
1.2 Chemical Limitations—Nonionic surfactants that exhibit a characteristic cloud point in general terms consist of a water-in-soluble moiety condensed with 50 to 75 % by weight of ethylene oxide. If the level of ethoxylation is too low the surfactant may not be water soluble at temperatures less than 30°C, and if it is too high no cloud point may exist.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

SIGNIFICANCE AND USE
5.1 The guide can be used to compare anti-redeposition performance of products; however, there is no confirmed basis for correlation of this controlled laboratory technique with consumers’ ranking of anti-redeposition performance.
SCOPE
1.1 This guide provides direction for measuring the ability of detergents to prevent the deposition of soils from detergent solutions onto fabrics. It is intended as a laboratory screening test to aid in the formulation of detergent products, for quality control, and as a basis between the purchaser and seller in standardizing specific products' performance.  
1.2 The anti-soil deposition performance of detergent products will vary greatly depending on the type of soils and fabrics used in the test. Therefore, selection of the soils, fabrics, reference detergents, and test conditions shall be made by agreement between the interested parties on the basis of experience.  
1.3 There is no single or combination of oily soils or particulate soils, or both, that will precisely predict overall the performance of a product or treatment with respect to anti-redeposition as perceived by a consumer. This guide is intended to assess or compare detergent performance with respect to the anti-redeposition performance for the specific soil chosen.  
1.4 The values stated in either inch-pound or SI units are to be regarded separately as the standard. The values given in parentheses are for information only.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Material safety data sheets are available for reagents and materials. Review them for hazards prior to usage.

ABSTRACT
These test methods cover the chemical analysis of sulfonated and sulfated oils. Water by distillation with volatile solvent and moisture and volatile matter by hot-plate shall be tested to meet the requirements prescribed. Titration test, extraction-titration test, and ash-gravimetric test shall be performed to meet the requirements specified. Total desulfated fatty matter, total active ingredients, unsaponifiable non-volatile matter, inorganic salts, total alkalinity, and total ammonia shall be tested to meet the requirements prescribed. In the absence of ammonium or triethanolamine soaps test method, brine test method, and in the presence of ammonium or triethanolamine soaps test method shall be performed to meet the requirements prescribed. Water-immiscible organic solvents volatile with steam shall be tested to meet the requirements prescribed.
SCOPE
1.1 These test methods cover the chemical analysis of sulfonated and sulfated oils. The analytical procedures appear in the following order:    
Section  
Moisture:  
Test Method A. Water by Distillation with Volatile Solvent  
4 – 9  
Test Method B. Moisture and Volatile Matter by Hot-Plate Method  
10 – 14  
Organically Combined Sulfuric Anhydride:  
Test Method A. Titration Test  
15 – 19  
Test Method B. Extraction-Titration Test  
20 – 24  
Test Method C. Ash-Gravimetric Test (in the Presence of True
Sulfonates)  
25 – 28  
Total Desulfated Fatty Matter  
29 – 32  
Total Active Ingredients  
33 – 36  
Unsaponifiable Nonvolatile Matter  
37 – 41  
Inorganic Salts  
42 – 46  
Total Alkalinity  
47 – 49  
Total Ammonia  
50 – 52  
Acidity as Free Fatty Acids or Acid Number:  
Test Method A. In the Absence of Ammonium or Triethanolamine Soaps  
53 – 56  
Test Method B. In the Presence of Dark Colored Oils but in the
Absence of Ammonium or Triethanolamine Soaps (Brine Test)  
57 – 60  
Test Method C. In the Presence of Ammonium or Triethanolamine Soaps  
61 – 63  
Water-Immiscible Organic Solvents Volatile with Steam  
64 – 70  
1.2 The values stated in inch-pound units are to be regarded as the standard. The metric equivalents of inch-pound units may be approximate.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Material Safety Data Sheets are available for reagents and materials. Review them for hazards prior to usage.

ABSTRACT
These test methods cover the sampling and chemical analysis of paste, powder, or liquid detergent fatty alkyl sulfates. The different procedure for sampling and chemical analysis of past, powder, or liquid detergent are presented and discussed in details. Distillation test, titration test, and gravimetric test shall be performed to meet the requirements prescribed. The calculations methods for chlorides as sodium chloride are presented in details.
SCOPE
1.1 These test methods cover the sampling and chemical analysis of paste, powder, or liquid detergent fatty alkyl sulfates.  
1.2 The procedures for sampling and analysis appear in the following order:    
Sections  
Sampling:  
Powders and Flakes Packed in Cans or Cartons  
4  
Powders and Flakes in Bulk  
5  
Liquids  
6  
Pastes  
7  
Preparation of Sample  
8  
Moisture by the Distillation Test Method  
11 – 14  
pH  
15  
Alkalinity  
16 – 19  
Alcohol-Soluble Matter  
20 – 22  
Alcohol-Insoluble Matter  
23 and 24  
Unsulfated Material  
25 – 28  
Combined Alcohols  
29 – 32  
Ester SO3:  
Method A. Titration Test Method  
36 and 37    
Sections  
Ester SO3:  
Method B. Gravimetric Test Method  
38 and 39  
Sodium Sulfate  
40 – 43  
Chlorides Calculated as Sodium Chloride (NaCl)  
44 – 47  
1.3 The values stated in either inch-pound or SI units are to be regarded separately as the standard. The values given in parentheses are for information only.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Material Safety Data Sheets are available for reagents and materials. Review them for hazards prior to usage.

ABSTRACT
These test methods detail the standard procedures for the chemical analysis of soaps containing synthetic detergents. The analytical procedures include the determination of the following chemical properties and substances: moisture and other matter volatile at a specified temperature; free alkali or free acid; anhydrous, salt-free soda soap; alcohol-soluble matter; matter insoluble in water; total alkalinity of matter insoluble in alcohol (alkaline salts); sodium silicate; phosphates; phosphates by colorimetric method using molybdenum blue); unsaponified and unsaponifiable matter; free fatty matter; chlorides in alcohol-soluble matter; rosin by McNicoll method; synthetic detergent by difference; and neutral inorganic salts.
SCOPE
1.1 These test methods cover procedures for the chemical analysis of soaps containing synthetic detergents.  
1.2 The analytical procedures appear in the following order:    
Sections  
Moisture and Other Matter Volatile at 105°C (Oven Method)  
5 and 6  
Free Alkali or Free Acid  
7 and 8  
Anhydrous, Salt-Free, Soda Soap  
9 – 12  
Alcohol-Soluble Matter  
13 and 14  
Matter Insoluble in Water  
15 and 15  
Total Alkalinity of Matter Insoluble in Alcohol (Alkaline Salts)  
16 and 17  
Sodium Silicate  
18 – 20  
Phosphates  
21 – 28  
Phosphate (Colorimetric Method Using Molybdenum Blue)  
29 – 34  
Unsaponified and Unsaponifiable Matter  
35 – 39  
Free Fatty Matter  
40  
Chlorides in Alcohol-Soluble Matter  
41 – 43  
Rosin (McNicoll Method)  
44 – 47  
Synthetic Detergent (by Difference)  
48  
Neutral, Inorganic Salts  
49  
1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.4 This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ABSTRACT
This test method covers the determination of the efficiency of ordinary commercial wetting agents using the skein test. It is applicable under limited and controlled conditions, but does not necessarily yield information correlating with specific end uses. The apparatus is comprised of a hook of standard weight depending on the concentration of the wetting agents and an anchor which shall be a flat, cylindrical, lead slug of specific dimensions. The reagents shall consist of water, acid and base test solutions, and wetting agent. The average of at least four determinations of the sinking time for each concentration of wetting agent shall be obtained and presented in plots with logarithmic coordinates. Standard deviation based on six replicate determinations shall also be calculated for precision.
SCOPE
1.1 This test method2,3 covers the determination of the efficiency of ordinary commercial wetting agents as defined in Terminology D459. This test method is applicable under limited and controlled conditions, but does not necessarily yield information correlating with specific end uses.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.